Weired issue odd IP's can ping the VIP and even can't on the Nexus 9K switch.

Hello experts!
we have two nexus 9k core, attached to the HP Blade v7000 chasis and VPC configured. All Vlans are HSRP are configured. VPC is configured successfully. But the weird this is that source IP address 10.1.2.3 can ping the dest VIP (on the loadblanacer) but 10.1.2.4 can't ie all odd IP's can ping the vip and even IP's can't ping and this is happening in all other Vlans. No firewall no security applience ... windows firewalls are turned off, no ACL's on the swtiches. If I shut down the interface on nexus 1 then all IP's can ping the VIP, as soon as I unshut the interface then .4 stops pinging, and if I shutdown the interface on nexus 2 then all IP's can ping. 10 gig links are connected to Flex fabric card and vpc port channel is up. Any thoughts or help ?
Nexus 1 Nexus 2

Similar Messages

Weired issue odd IP's can ping the VIP and even can't!

Hello experts!
we have two nexus 9k core, attached to the HP Blade v7000 chasis and VPC configured. All Vlans are HSRP are configured. VPC is configured successfully. But the weird this is that source IP address 10.1.2.3 can ping the dest VIP (on the loadblanacer) but 10.1.2.4 can't ie all odd IP's can ping the vip and even IP's can't ping and this is happening in all other Vlans. No firewall no security applience ... windows firewalls are turned off, no ACL's on the swtiches. If I shut down the interface on nexus 1 then all IP's can ping the VIP, as soon as I unshut the interface then .4 stops pinging, and if I shutdown the interface on nexus 2 then all IP's can ping. 10 gig links are connected to Flex fabric card and vpc port channel is up. Any thoughts or help ?
                               Nexus 1                                                                                                                        Nexus 2

Nexus 1
show hsrp active brief
                     P indicates configured to preempt.
                     |
Interface   Grp Prio P State    Active addr      Standby addr     Group addr
Vlan99      1   120 P Active   local            10.104.0.3       10.104.0.1      (conf)
Vlan160     5   120 P Active   local            10.104.5.3       10.104.5.1      (conf)
Vlan200     6   120 P Active   local            10.104.6.3       10.104.6.1      (conf)
Vlan210     7   120 P Active   local            10.104.7.3       10.104.7.1      (conf)
Vlan310     9   120 P Active   local            10.104.9.3       10.104.9.1      (conf)
Vlan350     11 120 P Active   local            10.104.11.3      10.104.11.1     (conf)
Vlan450     13 120 P Active   local            10.104.13.3      10.104.13.1     (conf)
Vlan700     14 120 P Active   local            10.104.14.6      10.104.14.4     (conf)
Vlan750     15 120 P Active   local            10.104.15.3      10.104.15.1     (conf)
=======================
Nexus 2
show hsrp active brief
                     P indicates configured to preempt.
                     |
Interface   Grp Prio P State    Active addr      Standby addr     Group addr
Vlan100     3   120 P Active   local            10.104.2.2       10.104.2.1
(conf)
Vlan150     4   120 P Active   local            10.104.4.2       10.104.4.1
(conf)
Vlan199     2   120 P Active   local            10.104.1.2       10.104.1.1
(conf)
Vlan300     8   120 P Active   local            10.104.8.2       10.104.8.1
(conf)
Vlan320     10 120 P Active   local            10.104.10.2      10.104.10.1
(conf)
Vlan400     12 120 P Active   local            10.104.12.2      10.104.12.1
(conf)
Vlan760     16 120 P Active   local            10.104.16.2      10.104.16.1

Interlace issues from 1080i50 to - iDVD, PS3, Apple TV and even FCE canvas

Hello all,
I am struggling to get smooth output from my FCE, interlace is thwarting me at every turn. I can produce a smooth DVD but at low quality with a work around as described at end of post, but really want smooth HD file, here is my workflow an plight
Have captured footage with Panasonic HDC-SD5 AVCHD camcorder in 1920 x 1080i50, imported into FCE with the newer 1920x1080 apple intermediate codec at 25fps
On inspection in the canvas set to 100% I see interlace jaggies, play back is not smooth either. So this is the first question should I really interlace in the canvas at this point?
Export to iDVD, use Quicktime Movie export, import into iDVD and produce DVD - result awful not smooth and blurred.
So try to export a HD MP4 , using Quicktime conversion. I produced in 1080i at 25fps and it's jumpy and blurred on the PS3 in playback. Then I did one at 29.97fps and as expected the video jumped every second BUT there were periods of smooth HD playback so I was so close! But just could not find the correct export setting.
Export to Apple TV directly from FCE produce awful results, however if I use the Quicktime movie and run it through visual hub I can encode for Apple TV using H.264 it de-interlaces correctly but movei not smooth (so it just removes a frame)
So, over a period of 2 days I have tried seemingly every export in Quicktime conversion for PS3 and Apple TV, VisualHub conversions and MPEG StreamClip all producing blurred or jumpy results due to interlacing.
The only smooth output was achived by using technique of another poster
Export Quicktime Movie and use Mpeg_StreamClip exportthat movie in
DVPRO50, set to PAL and 16:9, no deinterlace
then take movie and drop into iDVD and resulting DVD is Smooth
BUT quality is poor.
So, the main question is
How do I get all my nice HD footage out of FCE and onto Apple TV, PS3 or even iDVD in quality and without interlace making it jumpy or jaggy.
Any help would be greatly appreciated.
Cheers
Andy.

Wow thanks for quick reply. Apologies I didn't give full info.
I am viewing DVD on TV - well a plasma being played via DVD on PS3.
BUT, DVPRO50 is the only output that shows a "smooth" movie, if I playback on the canvas at 50% the interlace line are gone due to the scaling BUT the movie plays jumpy, so the DVPRo50 method is the only way I can get a smooth pan for example, every other method just gives a jumpy playback on DVD.
iDVD is set to Production quality, when I do a QT movie direct to iDVD without the DVPRO50, the quality is better but the movie is jumpy.
The movie is also 47 minutes long - it's quite big, file produced is about 19GB.
Also I understand about getting HD quality and BlueRay disk etc, but I would expect to get DVD quality from iDVD, doing the DVPRO50 conversion makes it pretty bad. but smooth!
As I said the anooying things is when I exported to MP4 on quicktime at 1080 HD and 18000kbps and 29.97 it also plays smooth for a short bursts of a few seconds (albeit jumping every second to 25 -> 29.97 issues), in 25 fps it's just blurry and jumpy. (playback on PS3)
Thanks

ACE30 - PING to VIP and Client side SVI not working

Hi Guys,
Having setup the ACE30 based on the configuration guides, I've been able to get basic load balancing working, probes, stickness etc. However in testing connectivty, I've noticed that from the real server on the backend I cannot seem to PING:
1. The VIP for the web service that the server is a part of
2. The Client side SVI
I'd like this to work to ensure full connectivity.
I've applied ACLs to the Client side SVI (on the ACE) to allow this in both directions, and also removed any ACLs attached to the client side SVI on the MSFC where the subnet is actually homed. However I just cannot seem to PING the Client side SVI on the ACE, or the VIP. Trying to understand if this is normal behavior.
Have inserted my config below for completeness.
ACE30 Config
login timeout 60
hostname ACE1
boot system image:c6ace-t1k9-mz.A90_6_3_5.bin
boot system image:c6ace-t1k9-mz.A4_1_0.bin
resource-class RC_1
limit-resource all minimum 10.00 maximum unlimited
access-list all line 8 extended permit ip any any
access-list v6-any line 8 extended permit ip anyv6 anyv6
class-map type management match-any REMOTE_ACCESS
description Remote access traffic match
2 match protocol telnet any
3 match protocol ssh any
4 match protocol icmp any
5 match protocol https any
policy-map type management first-match REMOTE_MGMT_ALLOW_POLICY
class REMOTE_ACCESS
    permit
interface vlan 768
description Management connectivity
ip address 10.20.40.72 255.255.255.0
service-policy input REMOTE_MGMT_ALLOW_POLICY
no shutdown
ip route 0.0.0.0 0.0.0.0 10.20.40.254
context VC_1
allocate-interface vlan 11
allocate-interface vlan 186
member RC_1
username admin password 5 $1$STizNv5q$i96.Qrt4C4SfHkbLyVT74. role Admin domain default-domain
username www password 5 $1$ZAn8bOtv$xmmNlH8akF6iYfXdQCKMo1 role Admin domain default-domain
ssh key rsa1 1024 force
! VC_1
ACE1/VC_1# sh run
probe http HTTP_PROBE1
interval 15
passdetect interval 60
expect status 200 200
open 1
rserver host RS_MONASH_WEB1
description Test Monash Web Server 1
ip address 10.194.27.177
inservice
serverfarm host SF_MONASH_WEB
probe HTTP_PROBE1
rserver RS_MONASH_WEB1 80
    inservice
sticky ip-netmask 255.255.255.255 address source STICKY_MONASH_WEB
timeout 3600
serverfarm SF_MONASH_WEB
class-map type management match-any REMOTE_ACCESS
description Remote access traffic match
2 match protocol ssh any
3 match protocol telnet any
4 match protocol icmp any
5 match protocol https any
class-map match-all VS_MONASH_WEB
2 match virtual-address 10.194.11.1 tcp eq www
access-list ALLOW_TRAFFIC_TOWARDS_ACE extended permit ip any any
access-list ALLOW_TRAFFIC_TOWARDS_ACE extended permit icmp any any
policy-map type management first-match REMOTE_MGMT_ALLOW_POLICY
class REMOTE_ACCESS
    permit
policy-map type loadbalance first-match PM_MONASH_WEB_LB
class class-default
    sticky-serverfarm STICKY_MONASH_WEB
policy-map multi-match PM_MULTI_MATCH_CLIENT_VIP
class VS_MONASH_WEB
    loadbalance vip inservice
    loadbalance policy PM_MONASH_WEB_LB
service-policy input REMOTE_MGMT_ALLOW_POLICY
interface vlan 11
description Client connectivity on Vlan 11
ip address 10.194.11.250 255.255.255.0
access-group input ALLOW_TRAFFIC_TOWARDS_ACE
access-group out ALLOW_TRAFFIC_TOWARDS_ACE       ! not sure if this is required as well?
service-policy input PM_MULTI_MATCH_CLIENT_VIP
no shutdown
interface vlan 186
description CSM www monash
ip address 10.194.27.189 255.255.255.240
access-group input ALLOW_TRAFFIC_TOWARDS_ACE    ! not sure if this is required?
access-group out ALLOW_TRAFFIC_TOWARDS_ACE      ! not sure if this is required?
ip dhcp relay server 130.194.15.17
ip dhcp relay server 130.194.15.1
ip dhcp relay enable
no shutdown
ip route 0.0.0.0 0.0.0.0 10.194.11.254
6500s
! test-clay1-gw - ACE connects to this 6500
svclc multiple-vlan-interfaces
svclc module 2 vlan-group 2
svclc vlan-group 2 11,171-499,768
! test-clay0-gw - Where Client side subnet, VLAN11 is homed
interface Vlan11
description Testlab server subnet
ip address 10.194.11.253 255.255.255.0
no shut
ip route 10.194.27.176 255.255.255.240 10.194.11.250
thanks
Sheldon

To ping your VIP of the webserver, you should apple the service-policy input command on VLAN 186 too. Currently the VIP only listens on VLAN 11. For the SVI i think that was forbidden by security reason, but i cant remember anymore. Maybe you just need to put the management policy on the interface VLAN 186. If it dont work, then my first guess was right

DOM support for 40G transponders on the Nexus 3172PQ switch

I have a new Nexus 3172PQ system which supports 40G transponders, but when the "sh inter ether 1/49 trans det" command is executed, the system responds with DOM is not enabled. I have transponders that support DOM in the system (QSFP-40G-LR4). IOS is 6.0.2. Question is does the 3172 support DOM for the 40G transponders?

FEX dual home is planned for mid next year.
MP BGP VPN V4 not supported on the platform. Not sure about the roadmap item either.

Main Server cannot ping the 2nd server in another location but the 2nd server can ping the main server

I have 3 servers : Main server, and 2 file servers in another country.
My main server can only ping the 2nd file server.
But both of our 2 file servers from another country can ping the main server.
In short, I cannot remote to the first file server.
The settings on both file servers are the same. And I don't have issues in accessing the 2nd file server using the Main server.
Can somebody have the patience to help me figure out the issue?

Being able to ping the server does not mean that you remotely access it.
If you are trying to RDP a server then you need to check that RDP is enabled on the server and that traffic to port 3389 is not blocked or filtered. You can use PortQryUI for checking.
For testing, you can temporary disable security software running on the servers and try again. Also, check the filtering done on network equipment in between your servers.
This posting is provided AS IS with no warranties or guarantees , and confers no rights.
Ahmed MALEK
My Website Link
My Linkedin Profile
My MVP Profile

The meaning of Interface Ethernet250/1 under the Nexus 2000 is connected to Nexus 5000 switch

Dear all,
Recently, I prepared and deploy a network monitoring system to monitor the new generation Nexus connected network. With using snmpwalk to query the interfacs information from the Nexus 5000 switch (one Nexus 2000 is connected to it via FlexLink), I found that other than normal Nexus 5000 and 2000 ports(ifName to be Ethernet1/1, Ethernet1/2, ... Ethernet190/1/1, Ethernet190/1/2...), a series of interface with ifName Ethernet250/1, Ethernet250/2, .... to be appeared in the interface SNMP tree. With logged into the Nexus 5000 and issue display interface command, I can only found the information on the normal interfaces but not the abnormal interface Ethernet250/1, ...
Would someone know what is it (do E250/1 is a logical interface like port channel or VLAN) and how to monitor it ? Thanks in advances.
HC Wong

I've not seen that myself. Could it perhaps be a VPC (Virtual Portchannel)?

DNS Issues - Can ping server name and IPs but not FQDNs.

Hi All,
Hopefully some one can help me here, I am having an issue where one of my domain attached servers cannot ping any FQDNs in the environment but it can ping the host names and the IPs and look up the host names from a reverse look up.
We have done the following troubleshooting:
Flushed and registered DNS cache.
Restarted the DNS client and net logon services on the effected server
Preformed standard checks and commands such as:
Checked the event logs and found there were warnings for DNS registration.
Compared the DNS settings in the network adapters across the rest of the servers in the environment and found that they were all the same. DNS Suffixes are added in the correct order and are set to register.
Pinging FQDNs which is not giving any results.
Tracert FQDNs which is also not giving any results.
Nslookup which is querying the DNS server directly and giving results as expected
Ran the command which reported successful: dcdiag /test:registerindns /dnsdomain:sub.domain.net /v
Checked and updated the permissions on DNS for the affected server to give the server full control of its own DNS entry.
Replaced the DNS Client service DLL with one from a server that is working as expected.
Also worth noting is that the affected server (as well as every other server in the environment) has 2 NICs, one that communicates with DNS and AD and the other does not have any DNS IPs set.
Not this is not the first time this happened, a reboot fixed the issue before but it seems to be a reoccurring problem now.
If any one can shed some light on this issue I would be grateful.
Regards,
Steve.

Hi Steve,
First, we should confirm if this issue is caused by DNS.
When you ping the FQDN, does the server show the correct corresponding IP address?
If no, there should be some error messages. If it is possible, please post the screenshot of this issue.
To check the process about how does server resolve the FQDN, please follow the steps below:
clear local DNS cache with command ipconfig /flushdns
perform the network capture
ping the specified FQDN
Check the DNS traffic
To download Network Monitor, please click the link below:
http://www.microsoft.com/en-hk/download/details.aspx?id=4865
Besides, have you tried to update the NIC driver to the latest version?
Best Regards.
Steven Lee Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

My Mac will not let me install any software I download. In some cases (Like quicktime) i get a message that says "Can't create the folder" I have it with adobe air and its creating all sorts of issues. My software is up to date and I have 10.8.2.

A whole bunch of issues here.
I can't install any software. It started when iPlayer stopped working at all. This led me to try to update software versions such as Adobe Air to 3.5 (Failed) then quicktime player 7.6.6 as recommended (Failed) then the printer packed up and I have tried to install the downloaded software drivers for Canon from the Apple site (Failed again)
In all cases they let me download so I have the file, but not install.
Quicktime tells me it can't install a file "/var/folders/15....then a long string of numbers....ending in T//install.1347YKihUc".
The Canon Print Driver has a very similar message.
Adobe Air says "An error occurred whilst installing....contact my administrator" which is me and I am fine with it ;-)
Remember this all started because my iPlayer (and my printer) just stopped working and I have been trying to fix those.
I am a bit techy but not much.
Can anyone assist?
Many Thanks.
Fozzie65

I have Firefox 3.6.6, and now that Firefox 4.0 is available, it crashes constantly. Sometimes less than 5 minutes after I open it. I have a Mac 10.4.11, so Firefox 4.0 isn't an option for me. When I asked Ff to check my plug-ins it said there was an error and to check back later. Twice.
Because I didn't have any (any) problems with my Ff before the upgrade became available, I am forced to question if Ff has done something to make the earlier version crash so you'll upgrade, but I can't afford to upgrade my Mac right now.
In the meantime, I do need a browser that works! I dislike Safari, Chrome is also not available on Mac 10.4.11, and Explorer is just plain not available on Mac.
Do you have any suggestions on how to fix my Firefox 3.6.6?
Ty

VPN - Can't ping the next hop

Next some advise... i've configured a VPN server -pptp on my router, create a vpn for client to site. At the moment, client computer can connect and established a connection to router. I can ping from client to router (192.168.5.1) but can't ping 192.168.5.2(switch) or 192.168.10.X (workstations)
What i'm trying to achieve is to access the internal network (192.168.10.X) which is from the layer 3 switch's end. Any help/extra eye would be good.
Here are my network design and config below:
Client Computer ---> Internet ---> (1.1.1.1) Cisco Router 881 (192.168.5.1) ---> Dell Powerconnect 6248 switch (192.168.5.2) --> Workstation(192.168.10.x)
Cisco 881 Router
aaa new-model
aaa authentication ppp default local
vpdn enable
vpdn-group PPTP-VPDN
accept-dialin
protocol pptp
virtual-template 1
interface FastEthernet0
description Link to Switch
switchport access vlan 5
interface FastEthernet1
no ip address
interface FastEthernet2
no ip address
interface FastEthernet3
switchport access vlan 70
no ip address
interface FastEthernet4
description INTERNET WAN PORT
ip address [EXTERNAL IP]
ip nat outside
ip virtual-reassembly in
duplex full
speed 100
crypto map VPN1
interface Vlan1
no ip address
interface Vlan5
description $ES_LAN$
ip address 192.168.5.1 255.255.255.248
no ip redirects
no ip unreachables
ip nat inside
ip virtual-reassembly in
interface Vlan70
ip address [EXTERNAL IP]
ip virtual-reassembly in
ip tcp adjust-mss 1452
interface Virtual-Template1
ip unnumbered FastEthernet4
encapsulation ppp
peer default ip address pool defaultpool
ppp authentication chap ms-chap
ip local pool defaultpool 192.168.10.200 192.168.10.210
ip forward-protocol nd
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 600 life 86400 requests 10000
ip nat inside source list NO-NAT interface FastEthernet4 overload
ip route 0.0.0.0 0.0.0.0 [EXTERNAL IP]
ip route 192.168.0.0 255.255.0.0 192.168.5.2
ip access-list extended NO-NAT
deny ip 192.168.0.0 0.0.255.255 10.1.0.0 0.0.255.255
permit ip 192.168.0.0 0.0.255.255 any
ip access-list extended VLAN70
permit ip [EXTERNAL IP] 0.0.0.15 192.168.10.0 0.0.1.255
permit tcp [EXTERNAL IP] 0.0.0.15 any eq smtp
permit tcp [EXTERNAL IP] 0.0.0.15 any eq www
permit tcp [EXTERNAL IP] 0.0.0.15 any eq 443
permit tcp [EXTERNAL IP] 0.0.0.15 any eq domain
permit udp [EXTERNAL IP] 0.0.0.15 any eq domain
ip access-list extended VPN
permit ip 192.168.10.0 0.0.1.255 10.1.0.0 0.0.1.255
permit ip [EXTERNAL IP] 0.0.0.15 10.1.0.0 0.0.1.255
ip access-list extended WAN
Layer 3 Switch - Dell Powerconnect 6224
ip routing
ip route 0.0.0.0 0.0.0.0 192.168.5.1
interface vlan 5
name "Connect to Cisco Router"
routing
ip address 192.168.5.2 255.255.255.248
exit
interface vlan 10
name "internal network"
routing
ip address 192.168.10.1 255.255.255.0
exit
interface ethernet 1/g12
switchport mode acesss vlan 5
exit
interface ethernet 1/g29
switchport mode access vlan 10
exit

Hi Samuel,
I went through your configuration and picked up some problematic lines..
First of all you can't have your vpn-pool to be in the 192.168.10.x/24 range because you already have that subnet used behind the switch ( this would only be possible if you had 192.168.10.x range directly connected to the router ). Also, you can't bind your Virtual Template to the WAN ip, it should bind to a interface with a subnet that includes your vpn-pool IP range.
The cleanest way to do this is,
Create a new loop back interface with a new subnet
interface loopback 0
ip address 192.168.99.1 255.255.255.0
Have new vpn pool defined,
ip local pool defaultpool 192.168.99.200 192.168.99.210
Change your Template to point the new loopback interface,
interface Virtual-Template1
ip unnumbered loopback0
encapsulation ppp
peer default ip address pool defaultpool
ppp authentication chap ms-chap
All the vpn clients will get an IP from 192.168.99.200 192.168.99.210 range. And they will be able to get in to the router and up to the desired 192.168.10.x/24 range behind the router. Packets will get in to the switch and then in to the host. Host will reply through the gateway( switch ) -> router -> Client.
PS: Earlier, even if your packets get to the host, the host will never try to send the reply packets back through the gateway ( switch ) because from its(hosts) point of view, the packet came from the same Lan, so the host will just try to "arp" for the senders MAC and will eventually time out)
Hope this helps.
Please don't forget to rate/mark helpful posts
Shamal

I can't seem to get my iMac (late 2009 model) into automatic sleep mode. If I manually put it into sleep I don't have any issues. I used to solve the issue by running "PleaseSleep" application but that doesn't work anymore since Lion.

I can't seem to get my iMac (late 2009 model) into automatic sleep mode. If I manually put it into sleep I don't have any issues.
I used to solve the issue by running "PleaseSleep" application but that doesn't work anymore since Lion. I now want to fix the underlying problem.
I'm not running any weird background processes and in my energy saver settings I've tagged "put the hard disk to sleep when possible:, "allow power button to put computer to sleep" and "automatically reduce brigthness". All pretty standard.
Is there anyone who can give me some pointers ?

Today I solved the same problem for my iMac running Snow Leopard. See https://discussions.apple.com/thread/3008791#15947706. The method may help you, too.
For me it was the DynDNS Updater preventing my iMac from automatically entering sleep mode.
To my knowledge the cause of this sleep problem can only be a peripheral device or a process. So I suggest to first unplug all peripherals and test whether that's the cause. If not, I suggest to terminate one process after another and to test automatic entering of sleep mode after each. Start with user processes; continue with system process if necessary.
At least that's the way I found the offending process. Fortunately, I was able to change the configuration of that process to allow again automatic entering of sleep mode.
Good luck!

I have installed the agent 10 or 15 times and one installation hasfailed, no error appeared during the installation but I am havinginconsistent issues with my ethernet card not working here and there. Werebooted and can log into Novell client but th

I have installed the agent 10 or 15 times and one installation has failed, no error appeared during the installation but I am having inconsistent issues with my ethernet card not working here and there. We rebooted and can log into Novell client but the login prompt did not appear for ESM client or the icon was not in the systray. Everything seems to work, besides at times (a couple times today) it terminates his ethernet card/connection. I would re-image his computer but he has several applications and it would take several hours, so I am hoping someone has an idea to fix this issue. So I was trying to figure out why he did not get the prompt to login and why it's not in the systray and it appears to not have completed the install? I checked the add/remove programs, its not listed within their, I also checked the registry and found nothing for endpoint within their, but the files are within c:\program files\novell\zenworks endpoint security.
I have also tried uninstalling it but that fails due to it "not being installed", and it will not reinstall over itself either.
I did notice that stuninstdrv.exe is running in task manager. Any help would be great...
Windows xp sp3
ESM 3.5.154
Thanks,
Andy

If you are searching the registry, check for the "Senforce" string. It should be at HKLM\Software\Senforce
Try running the install program for the ZSC with the following command line:
setup.exe /V"STUNINSTALL=1"
If you've specified an uninstall password, try this one instead:
setup.exe /V"STUNINSTALL=1 STUIP=password"" (please note the double quote at the end)
Let me know if that helped you.
Daniel
>>>
From: Andy_DeWees<[email protected] du>
To:novell.support.zenworks.endpoint-security-management
Date: 2/5/2009 12:52 PM
Subject: I have installed the agent 10 or 15 times and one installation hasfailed, no error appeared during the installation but I am havinginconsistent issues with my ethernet card not working here and there. Werebooted and can log into Novell client but the login prompt did not appearfor ESM client or the icon was not in the systray. Everything seems towork, besides at times (a couple times today) it terminates his ethernetcard/connection. I would re-image his computer but he has severalapplications and
I have installed the agent 10 or 15 times and one installation has failed, no error appeared during the installation but I am having inconsistent issues with my ethernet card not working here and there. We rebooted and can log into Novell client but the login prompt did not appear for ESM client or the icon was not in the systray. Everything seems to work, besides at times (a couple times today) it terminates his ethernet card/connection. I would re-image his computer but he has several applications and it would take several hours, so I am hoping someone has an idea to fix this issue. So I was trying to figure out why he did not get the prompt to login and why it's not in the systray and it appears to not have completed the install? I checked the add/remove programs, its not listed within their, I also checked the registry and found nothing for endpoint within their, but the files are within c:\program files\novell\zenworks endpoint security.
I have also tried uninstalling it but that fails due to it "not being installed", and it will not reinstall over itself either.
I did notice that stuninstdrv.exe is running in task manager. Any help would be great...
Windows xp sp3
ESM 3.5.154
Thanks,
Andy

I have a Mac on my home network and also a Systemline music server on same network. My PC was able to find the server but my MAC cannot. I can ping the server from the mac, but cannot actually connect . Also can't add the mac as a location from server

I have a Mac on my home network and also a Systemline music server on same network. My PC was able to find the server but my MAC cannot. I can ping the server from the mac, but cannot actually connect . Also can't add the mac as a location from server, despite following the Systemline instructions that impy this can be done.
Can anyone please advise what I am doing wrong?

Hi LowLuster
Thanks for reply. I am not an expert on these sharing protocols but I think I have turned on SMB sharing but still wont connect. I tried adding netwrik drive by using cntrl K in finder and using smb\\network address but nothing. It is driving me mad!!

How do I fix the compatibility issue between my iPhone 4S with iOS 7 and my Pioneer car stereo? There was no problem with iOS 6, but now I get a message saying "this device is not compatible" and so I can't use Netflix for example. How do I fix it?

How do I fix the compatibility issue between my iPhone 4S with iOS 7 and my Pioneer car stereo? There was no problem with iOS 6, but now I get a message saying "this device is not compatible" and so I can't use Netflix for example. How do I fix it?

This is a typical response from the manufacturer. Did you try the fix that Lawrence mentioned. When Apple or any other phone manufacturer update phone software, they have the latest Bluetooth installed. It is usually the problem with the radio manufacturer that they devices are using the older Bluetooth protocols. You can try this support document http://support.apple.com/kb/TS3581 and see if anything there helps, but generally it requires the radio manufacturer to update their firmware.

The screen on my MacBook goes black often. I can still see a faint image of what's on the screen, and can only get it to illuminate by moving it back and forth. What could the issue be? How can it be fixed?

The screen on my MacBook goes black often. I can still see a faint image of what's on the screen, and can only get it to illuminate by moving it back and forth. What could the issue be? How can it be fixed?

The startup disk may need repairing ...
Launch Disk Utility located in HD > Applications > Utilities
Select the startup disk on the left then select the First Aid tab.
Click: Verify Disk (not Verify Disk Permissions)
If the disk needs repairing, restart your Mac while holding down the Command + R keys. From there you can access the built in utilities in OS X Recovery to repair the startup disk.

Weired issue odd IP's can ping the VIP and even can't on the Nexus 9K switch.

Similar Messages

Maybe you are looking for