Welcome to the Solutions and Architectures Data Center & Virtualization Community

Welcome to the Solutions and Architectures Data Center & Virtualization Community. We encourage everyone to share their knowledge  and start conversations related to Data Center and Virtualization  Solutions and architectures.All topics are welcome, including  Servers – Unified Computing, Data Center Security, Data Center  Switching, Data Center Management and Automation, Storage Networking,  Application Networking Services and solutions to solve business  problems.
Remember,  just like in the workplace,  be courteous to your fellow forum  participants. Please refrain from  using disparaging or obscene language  or posting advertisements.
Cheers,
Dan Bruhn 

Hi,
I have a question...
I going to install two Nexus 7009 with three N7K-F248XP-25  modules on each one, I am planning to create 3 VDC, but at the initial configuration the system does not show the ethernets ports of these modules, even with the show inventory and show module I can see tah the modules are recognized and its status is OK. There is something that I have to do before start to configure these modules...? enable some feature or license in order to see the ports with show running CLI...?

Similar Messages

  • Welcome to the Solutions and Architectures Collaboration Community

    Welcome to the Solutions and Architectures Collaboration Community. We encourage everyone to share their knowledge  and start conversations related to Collaboration Solutions and  architectures.All topics are welcome, including Collaboration  Applications, Customer Collaboration, Telepresence, Unified  Communications and solutions to solve business problems.
    Remember,  just like in the workplace,  be courteous to your fellow forum  participants. Please refrain from  using disparaging or obscene language  or posting advertisements.
    Cheers,
    Dan Bruhn

    Hi,
    I have a question...
    I going to install two Nexus 7009 with three N7K-F248XP-25  modules on each one, I am planning to create 3 VDC, but at the initial configuration the system does not show the ethernets ports of these modules, even with the show inventory and show module I can see tah the modules are recognized and its status is OK. There is something that I have to do before start to configure these modules...? enable some feature or license in order to see the ports with show running CLI...?

  • Welcome to the Design and Architecture Community

    Welcome to the Network Infrastructure Design and Architecture Community.  We encourage everyone to share their knowledge and start conversations on design and overall network topology. All topics are welcome, including requirements and constraints of the network, tools and techniques, issues of hierarchy, leading practices, services, build strategies, architectures and solutions to solve business problems.
    Remember, just like in the workplace, be courteous to your fellow forum participants. Please refrain from using disparaging or obscene language or posting advertisements.
    Cheers,
    Dan BruhnCSC Community Manager

    been waiting to see a forum like this. This forum should amalgamate all the other areas like R&S, security, DC design, and provide more quality , proven solns and discuss problems/challenges as well. Will be following this forum regularly
    thanks dan for creating this community
    Regards Kishore

  • Welcome to Solutions and Architectures Borderless Networks Community

    Welcome to the Solutions and Architectures Borderless Networks Community.  We encourage everyone to share their knowledge and start conversations related to Borderless Solutions and architectures. All topics are welcome, including Switches, Routers, Security, Wireless, Cloud and System Management, WAN Optimization and solutions to solve business problems.
    Remember,  just like in the workplace, be courteous to your fellow forum  participants. Please refrain from using disparaging or obscene language  or posting advertisements.
    Cheers,
    Dan Bruhn       

    Hi,
    I have a question...
    I going to install two Nexus 7009 with three N7K-F248XP-25  modules on each one, I am planning to create 3 VDC, but at the initial configuration the system does not show the ethernets ports of these modules, even with the show inventory and show module I can see tah the modules are recognized and its status is OK. There is something that I have to do before start to configure these modules...? enable some feature or license in order to see the ports with show running CLI...?

  • New Solutions And Architectures Community

    I am pleased to announce the launch of our new Cisco Solutions and Architectures Community with sub-communities for Borderless Networks, Collaboration, Data Center & Virtualization.  We encourage everyone to share their knowledge and start conversations  related to network design and overall Cisco network topology.
    All topics are welcome, including WAN, LAN, enterprise, service provider, data center / virtualization, wireless, security, collaboration, voice & video network design architecture and solutions to solve business problems.
    The  content from our pilot Network Infrastructure “Design and Architecture”  community will be merged into the appropriate Solutions and  Architectures sub-community.
    Cheers,
    Dan

    Hi,
    I have a question...
    I going to install two Nexus 7009 with three N7K-F248XP-25  modules on each one, I am planning to create 3 VDC, but at the initial configuration the system does not show the ethernets ports of these modules, even with the show inventory and show module I can see tah the modules are recognized and its status is OK. There is something that I have to do before start to configure these modules...? enable some feature or license in order to see the ports with show running CLI...?

  • Replication between 130 nodes and 1 Data Center

    Hi everyone.
    I have 130 database nodes (Oracle Standard Edition One) with a big distance of separation, and 1 Data Center with 3 nodes (Oracle Real Application Cluster 10g R2). The connection between nodes and datacenter is through various ISP ( WAN).
    I have exactly the same model design of database in nodes and datacenter.
    DataCenter is a repository of data for reporting to directors and dictate the business rules to guide all nodes.
    Each node have approximately 15 machines connected with desktop application.
    In other words Desktop Application with a Backend Database (node).
    My idea of replication is not instantly, when a transaction commit in a node then replicate to datacenter. Also over nigth replicate images because is heavy, approximately 1 mg per image. Each image correspond to one transaction.
    On the orher hand i have to replicate some data from datacenter to nodes, business rule, for example: new company names, new persons, new prohibitions, etc.
    My problem is to determine th best way to replicate data through nodes to datacenter.
    Please somebody could suggest me the best solution.
    Thanks in advanced.

    Last I checked, Streams and multi-master replication require enterprise edition databases at both ends, which rules them out for the sort of deployment you're envisioning.
    If a given table will only ever be modified on nodes or on the master site, never both, you can build everything as read-only materialized views. This would probably require, though, that the server at the data center have 130 copies of each table, 1 per node. For schemas of any size, this obviously gets complicated very quickly. For asynchronous replcation to work, you'd need to schedule periodic refreshes, which assumes that you have relatively stable internet connections between the nodes and the data center.
    I guess I would tend to question the utility of having so many nodes. Is it really necessary to have so many? Or could you just beef up the master and have everyone connect directly?
    Justin
    Distributed Database Consulting, Inc.
    http://www.ddbcinc.com/askDDBC

  • My iPhone 5 has broken and is being replaced with a new iPhone tomorrow. However, My carrier (orange) will b picking up my broken iPhone and I am unsure how to secure the content and icloud data on the broken phone. Is there a way to display the data?

    My iPhone 5 has broken and is being replaced with a new iPhone tomorrow. However, My carrier (orange) will b picking up my broken iPhone and I am unsure how to secure the content and icloud data on the broken phone. Is there a way to disable the data held on it and ensure that if it is fixed, nobody can use/see my data and access my account?

    Hi Gazpan,
    Thanks for visiting Apple Support Communities.
    I recommend using the steps in this article to back up your iPhone if possible:
    iOS: Back up and restore your iOS device with iCloud or iTunes
    http://support.apple.com/kb/ht1766
    You may also find this advice helpful for your situation:
    What to do before selling or giving away your iPhone, iPad, or iPod touch
    http://support.apple.com/kb/ht5661
    If you no longer have your iOS device
    If you're using iCloud and Find My iPhone on the device, you can erase the device remotely and remove it from your account by signing in to icloud.com/find, selecting the device, and clicking Erase. When the device has been erased, click Remove from Account.
    If you're unable to complete either of the above steps, you should change your Apple ID password. Changing your password won't remove any personal information that is cached on the device, but it will make sure that the new owner can't delete your information from iCloud.
    Cheers,
    Jeremy

  • The contacts and calendar data on my iPod touch will not sync with my Mac

    I have a 2nd generation ipod touch, and an iMac running iTunes 8.2.1.
    I have been away from my mac for a few months and have entered a lot of contact and calendar info into my ipod touch.
    Now, when I try to sync the contacts and calendar data on my ipod touch with my mac, the data will not sync to my mac.
    Similarly, for the last couple months, the contact and calendar data on my ipod touch has not been able to sync with my mobileme account.
    I cannot afford to lose the contact and calendar data on my ipod touch.
    Can anyone kindly inform me how to fix this syncing problem without losing such data?

    DGKSA wrote:
    I ended up entering the data onto my Mac, then nuking my iPod touch with a restore.
    So, there is no need to respond to my question.
    You can also mark your post as "solved" if you solved your problem on your own.
    Only the original topic poster has the option to mark replies as either Helpful or Solved or to not mark a reply at all. The originator can also end the discussion by marking the topic as "answered," which displays a green star at the top of the topic page to let everyone know that the topic contains valid helpful information.
    copied from "Terms of Use"

  • How to display the username and current date in OAF  page Footer region

    Hi,
    I need to display the username and Current-Date in footer region.If anybody knows the procedure then please share with me.
    Thanks
    Divya Agarwal

    Hi,
    Read this Thread:--
    You have to capture the UserName and Date in the Process Request Method of page Controller and invoke a method which will subsequently get and set the value in some attribute.
    String userName = pageContext.getUserName();
    How to populate Current Date and Time in OAF page through CO
    Thanks
    --Anil                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                   

  • Increment the version and current date in .ver file

    Hi All,
    I have the version.ver file and it looks like
    [version]
    BuildDates=2014.10.01
    Script=01
    MainVersion=1.00.00.00:01
    I want to increment the values and current date if i trigger the build using batch script. The output i need is like this
    BuildDates=yy.mm.dd (current date)
    Script=02
    MainVersion=1.00.00.00:02
    Thanks in advance

    Thanks for your reply. This is my script
    @echo off>newfile&setlocal enabledelayedexpansion
    :: set up your date here. It probably won't match my format so you'll need to adapt:
    set dt=%date:~10,4%.%date:~7,2%.%date:~4,2%
    for /f "skip=2 tokens=2,3 delims==:" %%a in ("filename") do (
    set v= %%b
    set v= !v: 0=!
    set /a v+=1
    set v=0!v!
    set v=!v:~-2!
    >>newfile echo SCRIPT=!v!
    >>newfile echo BuildDates=%dt%
    >>newfile echo MajorVersion=%%a:!v!
    goto :aa
    :aa
    more +3 "filename" >> newfile
    del "filename"
    ren newfile "filename"
    Before execute the script my file will be look like:
    version]
    BuildDates=date
    Script=09
    MainVersion=3.00.00.00:09
    after executing i am getting the output value as
    BuildDates=date
    Script=01
    MainVersion=19:01
    MainVersion=3.00.00.00:09

  • Save the file and give date & time stamp

    1. Reading the Excel file from the selection screen as a parameter.
    2. Using F.M. ALSM_EXCEL_TO_INTERNAL_TABLE reading Excel file into
        Internal table.
    3. Implementing the Business Logic.
    4. Move output to Final Internal table.
    5. Final internal table should generate a Flat file. By using GUI_DOWNLOAD.
    6. That flat file should be saved with the name and location given in the Excel.
    7. When ever I run the program output file will generate in the same location but with date and time stamp. Because I’m running the program for range of employees say initially I run for 1 – 10,000 employees next 10,001- 20,000 like that.
    Whenever I run for 2nd time it will overwrite the previous output, that’s the reason I’m using date and time stamp.
    Eg:
    PERSONAL Numbers              Name                                         Location
    00000001                 xxxxx-24.04.2007-10.30          C:\        
    00000002                 xxxxx-24.04.2007-10.35
    00000003                 xxxxx-25.04.2007-10.40
    00000004                                  xxxxx-25.04.2007-10.30
    Can any one help me how to save the file and give date & time stamp through hardcode?
    please help me in this issue.

    I am not clear with your problem. Based on the understanding of your question,
    there  can be two cases.
    1- U want to insert time stamp in the output file.
    2- Time stamp is already there, u just have to solve the overwriting issue.
    If your question goes with option 2, You can make use of import parameters
    <b>CONFIRM_OVERWRITE</b> : Which will ask for confirmation before overwriting.
    <b>APPEND</b> : which you can choose either to append the data to the existing file or overwrite it.
    Please inform if the issue is not resolved.
    Message was edited by:
            BINU RAJ BINU

  • I don't see the BLStart and BLFinish Dates

    Hello
    I have project A and the time to assign as a project baseline B newly imported, I can't see the BLFinish and BLStart dates.
    Project B has a start and end dates, but when he is assigned as the project BaseLine A, no dates are displayed.
    See the screenshot: http://img213.imageshack.us/img213/7217/blproblem.jpg
    Thanks
    AHR

    Hi.
    The baseline is correct assigned.
    See the screenshots.
    Maintain Baseline: http://img411.imageshack.us/img411/2231/maintainbl.jpg
    Assign Baseline: http://img440.imageshack.us/img440/3105/assignbl.jpg
    I´m schedule with date 02Aug10
    any idea?
    Thanks

  • Standard Idoc or BAPI to trasfer the routes and stages data

    Hi guys,
    We want to transfer the routes and stages data from one SAP system to other SAP system . can u suggest any standard idocs or BAPIs to do the job.
    thanks
    sankar
    Edited by: sudhakar murthy on Apr 1, 2009 10:18 AM

    hello guys
    any idea on this????
    thanks

  • Calculate the working days having the start and end dates only

    Hi,
    Can BIP be able to calculate the working days having the start and end dates only? It is like the NETWORKDAYS function in Excel. (i.e. excluding weekends and holidays).
    Thanks.

    Not out of the box.
    But You could extend your BIP functions
    Look at here:
    http://blogs.oracle.com/xmlpublisher/2009/05/bip_by_extension.html
    Based on that what you need is similar to the following Java code:
    http://objectlabkit.sourceforge.net/
    regards
    Jorge A.

  • Getting the start  and end dates of the week

    Hi,
    I was stuck with a problem in getting the start date and end date of the week,i know the month ,week and year also,with these three values how can i get the start and end dates of a week.please help me
    Thanks

    There is no simple way. It has to be a math calculation.
    There are several ways you can get the dates. First you have to know what day is January 1st and what day is december 31st for a particular year. Second you have to check whether the given year is a leap year or not. Based on the abvove information you should be able to find out what day is a particular date.
    Hope this helps to get you started.
    - Venkat Dhurjati.

Maybe you are looking for