WES610N - only one MAC address for all connected devices

Hi! I use a WES610N 4-port WLAN bridge to connect my audio and video devices (Pioneer AV receiver, Samsung TV set and a WD Live TV box) to my E4200 router upstairs. This works fine and the WLAN connection works stable and fast. There's a Synology 212j NAS running DM 3.2 connected to my E4200 router. On this NAS a DLNA/UPnP media server is running to stream audio and video from the NAS to my Receiver, to my TV set and to the WD Live TV box. Audio and video is ok but i also want to send photos from the NAS direct to the TV and WD Live. To see the photos in the correct solution i have to configure a DLNA profile on the media server for each DLNA client which connects to the media server. I have to configute this based on the device name, IP address and MAC address shown in the clinet list of the media server. So far so good - and here's my problem: Every device connected to the WES610N is seen with the same MAC address - the one of the WES610 - by the media server. This confuses the server and it's not possible to assign a DLNA profile to each of the devices (TV, Receiver, WD box) because the IP - MAC pairing always changes when one of the devices sends data packets to the media server. So the assigned profile configuration gets lost and switches back to standard DLNA profile and photos can not be displayed correct by the devices. So what i would need is that every device connected to the WES610N is seen by the media server by it's on MAC address. Is there a solution or are there plans to implement this in future firmware versions? Thx, BR Christian

You can try the following combination of settings :-
A] With the help of Cisco Connect Software (if at all you have installed the router with the help of this software)
1] Open the software and go to the option which says "Router Settings"
2] Then click on the option which says "Advanced Settings" which will take you to the router's configuration page.
3] Lower the MTU (Maximum Transmission Unit) from 1500 to 1400 or less (usually found on your routers main/ basic setup page)
4] Then click on Security tab disable SPI Firewall Protection, uncheck Filter Anonymous Internet Requests...
B] If you haven't installed Cisco Connect then you can log on to the router's user interface using it's default IP address in the browser which is 192.168.1.1 and type in 'admin' as the password leaving the user name field blank. This will take you to the router's web interface and then follow steps as mentioned above to make the changes.
Then check the connectivity status...

Similar Messages

  • Should you use only one smtp address for all email accounts?

    My iPhone and iPad will not send mail from either of two email accounts. Ive checked the smtp settings and passwords several times. I have several email accounts with different providers/servers though, so should there only be one server chosen for all? Cant figure out why my email won't send! Anyone know an answer?

    No.  Each mail provider has its own SMTP server. And you won't be able to send email from one provider's email account through another provider's smtp server.
    Each account should have its provider's SMTP server set as its Primary Server.  And The rest of the smtp servers should be turned off for that particular account. 

  • I want only one apple ID for all my devices

    I have an apple ID and so does my wife.  Between the four family members we 8 plus apple devices.  I want to put everything on hers and just have one.  Mine has the least amount of music and apps.  Can it be done? How do you do it without losing anything?

    What exactly are you wanting to do. It is a little unclear from your post. You've also posted in the iTunes Match forum. Does your question have something to do with iTunes Match?
    Keep in mind that if you all have your own content purchased with indvidual iTunes Store accounts, trying to consolidate is going to cause everyone big headaches. But if you give us more details perhaps we can help you sort it out.

  • I have an Airport Extreme as my router and am using time capsule to extend the network in my new house. My ISP is only providing me 4-5 ip addresses and wants me to set up my router to issue out new ip addresses for all my devices.How do I fix this?Help

    I have an Airport Extreme as my router and am using time capsule to extend the network in my new house. My ISP is only providing me 4-5 ip addresses and wants me to set up my router to issue out new ip addresses for all my devices.How do I fix this?Help.
    They said I need to change my settings to NAT settings. I haven't been able to figure out or find anything. I have also spoken to Apple Support on the phone for hours without being able to figure out how to do this ( i don't think he knew much either lol.) Please help me because I've got about 15-20 devices in my house that require to be connected to the internet and this is just making things ridiculously slow and painful for me.
    Thanks!

    It is on DHCP & NAT under router mode yet my isp is still the one issuing ip addresses to my devices instead of the router issuing them

  • E4200 v2 - Uses multiple MAC addresses for the same device

    This unit seems pretty good at first but on looking at the Web interface I noticed that it was using multiple mac addresses for the same device and showing devices on the lan on the Wireless side and other odd things.
    After a week of running it the home server network started to get erratic, it would seem to all point to dns and dhcp issues in the router.
    Seems the V1 had the same issues that they did not fix on this.
    The Cisco connect software shows 5 devices the Web based utility shows 3??.
    Its pretty bad that they charge nearly $200 and cannot be bothered to finish the unit or address the issues that were in V1.

    I am afraid I didn't get the clear picture of the issue mentioned in the post. Could you please elaborate a little bit? If you connect a device/computer wired and then later you connect it wirelessly. It is obvious that you would get to see two different MAC addresses for the same device, one for the LAN adaptor and other one for WLAN adaptor. If that is what you are referring to?
    Secondly, may I  know, what issues did you face with DNS and DHCP in the router? Is it not able to resolve the DNS or something else or DHCP is not sending IP address to the clients?

  • How to force RH9 to use only one master stylesheet for all Word imports?

    I have set a stylesheet (css) as the default for my RH9 WebHelp project in project settings. When I import Word documents into the project, the edit import setting dialog does not show this stylesheet in the list of available stylesheets for the import.
    What is happening instead is a proliferation of unwanted stylesheets derived from all the imported documents. I then have to manually re-set all the new topics to the master stylesheet.
    How can I stop this, and force RH9 to use only the one master stylesheet for all imports?

    cid:[email protected]
    Hi Peter,
    That’s what I thought I was doing in the Project Settings>Import tab>CSS for Style Mapping selection. Maybe that isn’t what it’s meant to do. It’s just getting annoying having all these unneeded files popping up in the project manager so that I have trouble distinguishing the “real” topics from the extra stuff.
    Michael West | Business Improvement | Aurecon
    Ph: +61 3 8683 1996 | Fax: +61 3 8683 1444 | Mob: 0407 485 228
    Email: [email protected]
    PO Box 321, South Melbourne | VIC 3205 | Australia
    http://www.aurecongroup.com
    http://www.aurecongroup.com/apac/groupentity/

  • [Windows] list MAC addresses of ethernet-connected devices to AEBS?

    I have an ethernet connected device (among others) that is running headless, so I need to create a static IP ("DHCP Reservation") based on the MAC address to SSH into the device.
    This device is connected to my AEBS with an ethernet cable, and I cannot figure out where in the Airport Utility app lists MAC addresses connected by ethernet. This is very easy if it were a wirelessly connected device but it appears the Airport Utility -> Advanced -> Logging and Statistics tab -> "Logs and Statistics" only holds information of wirelessly connected devices.
    I am connecting to my AEBS with the most updated Airport Utility for Windows v5.6.1
    So, where do you find the MAC addresses listed of ethernet-connected devices using Windows Airport Utility?

    but it appears the Airport Utility -> Advanced -> Logging and Statistics tab -> "Logs and Statistics" only holds information of wirelessly connected devices.
    That would be true if the AEBS is configured in Bridge Mode.  In this case, another device....you likely call this your modem....is providing DHCP information to all connected devices. That is the device where you need to locate MAC Addresses and set up Static IP addresses.....not the AEBS.
    If your AirPort Extreme is in charge of providing DHCP services, then the window in Airport Utility will have a DHCP tab, which will display all of this information for both wired and wireless devices.  If you don't see a DHCP tab....this is yet another confirmation that the AEBS is in Bridge Mode.

  • MAC addresses of ethernet-connected devices to AEBS?

    I have an ethernet connected device (among others) that is running headless, so I need to create a static IP ("DHCP Reservation") based on the MAC address to SSH into the device.
    This device is connected to my AEBS with an ethernet cable, and I cannot figure out where in the Airport Utility app lists MAC addresses connected by ethernet. This is very easy if it were a wirelessly connected device but it appears the Airport Utility -> Advanced -> Logging and Statistics tab -> "Logs and Statistics" only holds information of wirelessly connected devices.
    I am connecting to my AEBS with the most updated Airport Utility for Windows v5.6.1

    but it appears the Airport Utility -> Advanced -> Logging and Statistics tab -> "Logs and Statistics" only holds information of wirelessly connected devices.
    That would be true if the AEBS is configured in Bridge Mode.  In this case, another device....you likely call this your modem....is providing DHCP information to all connected devices. That is the device where you need to locate MAC Addresses and set up Static IP addresses.....not the AEBS.
    If your AirPort Extreme is in charge of providing DHCP services, then the window in Airport Utility will have a DHCP tab, which will display all of this information for both wired and wireless devices.  If you don't see a DHCP tab....this is yet another confirmation that the AEBS is in Bridge Mode.

  • Only one X session for all normal users combined possible

    Hi, I'm currently experimenting with the new xorg-server 1.16 with which it is possible to start and run the X server as a user.
    Setup: No display manager running. startx is used. No modifications of global xserverrc or other files.
    ~/.xinitrc looks like this for all users:
    startxfce4
    As root it is possible to start multiple X sessions (on different virtual terminals of course).
    But as a user only one X session is possible.
    After user flo has started a X session on tty1, the following occurs:
    Permissions for tty2 before startx
    crw------- 1 boolian tty 4, 2 24. Jul 10:24 /dev/tty2
    If I try to start a second X session via startx on another virtual terminal (here: tty2), the process aborts with the following message:
    X.Org X Server 1.16.0
    Release Date: 2014-07-16
    X Protocol Version 11, Revision 0
    Build Operating System: Linux 3.15.1-1-ARCH x86_64
    Current Operating System: Linux flo.tower 3.15.6-1-ARCH #1 SMP PREEMPT Fri Jul 18 07:06:42 CEST 2014 x86_64
    Kernel command line: BOOT_IMAGE=../vmlinuz-linux root=/dev/sda1 rw initrd=../initramfs-linux.img
    Build Date: 18 July 2014 07:12:40PM
    Current version of pixman: 0.32.6
    Before reporting problems, check http://wiki.x.org
    to make sure that you have the latest version.
    Markers: (--) probed, (**) from config file, (==) default setting,
    (++) from command line, (!!) notice, (II) informational,
    (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
    (==) Log file: "/home/boolian/.local/share/xorg/Xorg.1.log", Time: Thu Jul 24 10:24:21 2014
    (==) Using config directory: "/etc/X11/xorg.conf.d"
    (EE)
    Fatal server error:
    (EE) xf86OpenConsole: Cannot open virtual console 2 (Permission denied)
    (EE)
    (EE)
    Please consult the The X.Org Foundation support
    at http://wiki.x.org
    for help.
    (EE) Please also check the log file at "/home/boolian/.local/share/xorg/Xorg.1.log" for additional information.
    (EE)
    (EE) Server terminated with error (1). Closing log file.
    xinit: giving up
    xinit: unable to connect to X server: Connection refused
    xinit: server error
    After this unsuccessful call to startx, the permissions for the tty2 have changed, but only the owner not the rwx flags.
    crw------- 1 root tty 4, 2 24. Jul 10:24 /dev/tty2
    Interestingly the permissions for the tty with the running X server stay as expected all the time.
    crw------- 1 flo tty 4, 1 24. Jul 10:37 /dev/tty1
    My first guess was, that the suid bit of Xorg.wrap has something to do with it. But I moved the binary and the behavior stayed the same.
    Another guess is, that systemd-logind has something to do with it as it is repsonsible for the permissions (see [0] and [1]).
    Can anybody reproduce this behaviour?
    Has anybody hints where to go next? I'm currently building a new kernel with the audit framework enabled to check which process changes the permission of the tty when startx is called.
    I'm reluctant to open a bug report as I know too little about the problem or whether it is a bug at all.
    Greetings.
    [0]http://dvdhrm.wordpress.com/2013/08/24/ … -on-linux/
    [1]http://dvdhrm.wordpress.com/2013/08/24/ … ing-works/

    I have captured all systemcalls which go to /dev/tty2 (which is dev with major 4 and minor 2) with the following auditctl line:
    -a always,exit -F arch=x86_64 -S all -F devmajor=4 -F devminor=2 -F key=vt2222
    This is the result:
    [root@flo rules.d]# ausearch -i -k vt2222
    type=CONFIG_CHANGE msg=audit(24.07.2014 13:19:49.400:83) : auid=flo ses=1 op="add rule" key=vt2222 list=exit res=yes
    type=PROCTITLE msg=audit(24.07.2014 13:19:53.749:84) : proctitle=/sbin/agetty
    type=PATH msg=audit(24.07.2014 13:19:53.749:84) : item=0 name=/dev/tty2 inode=24 dev=00:05 mode=character,620 ouid=root ogid=tty rdev=04:02 nametype=NORMAL
    type=CWD msg=audit(24.07.2014 13:19:53.749:84) : cwd=/
    type=SYSCALL msg=audit(24.07.2014 13:19:53.749:84) : arch=x86_64 syscall=stat success=yes exit=0 a0=0x6665a0 a1=0x7fffea504e50 a2=0x7fffea504e50 a3=0x666590 items=1 ppid=1 pid=5903 auid=unset uid=root gid=root euid=root suid=root fsuid=root egid=root sgid=root fsgid=root tty=tty2 ses=unset comm=login exe=/usr/bin/login key=vt2222
    type=PROCTITLE msg=audit(24.07.2014 13:19:53.749:85) : proctitle=/sbin/agetty
    type=PATH msg=audit(24.07.2014 13:19:53.749:85) : item=0 name=/dev/tty2 inode=24 dev=00:05 mode=character,620 ouid=root ogid=tty rdev=04:02 nametype=NORMAL
    type=CWD msg=audit(24.07.2014 13:19:53.749:85) : cwd=/
    type=SYSCALL msg=audit(24.07.2014 13:19:53.749:85) : arch=x86_64 syscall=lstat success=yes exit=0 a0=0x6665a0 a1=0x7fffea5050c0 a2=0x7fffea5050c0 a3=0x7fffea504d00 items=1 ppid=1 pid=5903 auid=unset uid=root gid=root euid=root suid=root fsuid=root egid=root sgid=root fsgid=root tty=tty2 ses=unset comm=login exe=/usr/bin/login key=vt2222
    type=PROCTITLE msg=audit(24.07.2014 13:19:53.749:86) : proctitle=/sbin/agetty
    type=PATH msg=audit(24.07.2014 13:19:53.749:86) : item=0 name=/dev/tty2 inode=24 dev=00:05 mode=character,620 ouid=root ogid=tty rdev=04:02 nametype=NORMAL
    type=CWD msg=audit(24.07.2014 13:19:53.749:86) : cwd=/
    type=SYSCALL msg=audit(24.07.2014 13:19:53.749:86) : arch=x86_64 syscall=access success=yes exit=0 a0=0x6665a0 a1=W_OK|R_OK a2=0x7fffea5050c0 a3=0x7fffea504d00 items=1 ppid=1 pid=5903 auid=unset uid=root gid=root euid=root suid=root fsuid=root egid=root sgid=root fsgid=root tty=tty2 ses=unset comm=login exe=/usr/bin/login key=vt2222
    type=PROCTITLE msg=audit(24.07.2014 13:19:53.749:87) : proctitle=/sbin/agetty
    type=PATH msg=audit(24.07.2014 13:19:53.749:87) : item=0 name=(null) inode=24 dev=00:05 mode=character,620 ouid=root ogid=tty rdev=04:02 nametype=NORMAL
    type=SYSCALL msg=audit(24.07.2014 13:19:53.749:87) : arch=x86_64 syscall=fchown success=yes exit=0 a0=0x0 a1=0x0 a2=0x0 a3=0x7fffea504d00 items=1 ppid=1 pid=5903 auid=unset uid=root gid=root euid=root suid=root fsuid=root egid=root sgid=root fsgid=root tty=tty2 ses=unset comm=login exe=/usr/bin/login key=vt2222
    type=PROCTITLE msg=audit(24.07.2014 13:19:53.749:88) : proctitle=/sbin/agetty
    type=PATH msg=audit(24.07.2014 13:19:53.749:88) : item=0 name=(null) inode=24 dev=00:05 mode=character,620 ouid=root ogid=root rdev=04:02 nametype=NORMAL
    type=SYSCALL msg=audit(24.07.2014 13:19:53.749:88) : arch=x86_64 syscall=fchmod success=yes exit=0 a0=0x0 a1=0600 a2=0x0 a3=0x7fffea504d00 items=1 ppid=1 pid=5903 auid=unset uid=root gid=root euid=root suid=root fsuid=root egid=root sgid=root fsgid=root tty=tty2 ses=unset comm=login exe=/usr/bin/login key=vt2222
    type=PROCTITLE msg=audit(24.07.2014 13:19:53.749:89) : proctitle=/sbin/agetty
    type=PATH msg=audit(24.07.2014 13:19:53.749:89) : item=0 name=/dev/tty2 inode=24 dev=00:05 mode=character,600 ouid=root ogid=root rdev=04:02 nametype=NORMAL
    type=CWD msg=audit(24.07.2014 13:19:53.749:89) : cwd=/
    type=SYSCALL msg=audit(24.07.2014 13:19:53.749:89) : arch=x86_64 syscall=open success=yes exit=0 a0=0x6665a0 a1=O_RDWR|O_NONBLOCK a2=0x7f7a7bb9edf0 a3=0x7fffea504ce0 items=1 ppid=1 pid=5903 auid=unset uid=root gid=root euid=root suid=root fsuid=root egid=root sgid=root fsgid=root tty=tty2 ses=unset comm=login exe=/usr/bin/login key=vt2222
    type=PROCTITLE msg=audit(24.07.2014 13:19:54.409:91) : proctitle=/sbin/agetty
    type=PATH msg=audit(24.07.2014 13:19:54.409:91) : item=0 name=(null) inode=24 dev=00:05 mode=character,600 ouid=root ogid=root rdev=04:02 nametype=NORMAL
    type=SYSCALL msg=audit(24.07.2014 13:19:54.409:91) : arch=x86_64 syscall=fchown success=yes exit=0 a0=0x0 a1=0x3e8 a2=0x5 a3=0x683ce7 items=1 ppid=1 pid=5903 auid=flo uid=root gid=root euid=root suid=root fsuid=root egid=root sgid=users fsgid=root tty=tty2 ses=15 comm=login exe=/usr/bin/login key=vt2222
    type=PROCTITLE msg=audit(24.07.2014 13:19:54.409:92) : proctitle=/sbin/agetty
    type=PATH msg=audit(24.07.2014 13:19:54.409:92) : item=0 name=(null) inode=24 dev=00:05 mode=character,600 ouid=flo ogid=tty rdev=04:02 nametype=NORMAL
    type=SYSCALL msg=audit(24.07.2014 13:19:54.409:92) : arch=x86_64 syscall=fchmod success=yes exit=0 a0=0x0 a1=0600 a2=0x5 a3=0x683ce7 items=1 ppid=1 pid=5903 auid=flo uid=root gid=root euid=root suid=root fsuid=root egid=root sgid=users fsgid=root tty=tty2 ses=15 comm=login exe=/usr/bin/login key=vt2222
    type=PROCTITLE msg=audit(24.07.2014 13:19:54.413:93) : proctitle=login -- flo
    type=PATH msg=audit(24.07.2014 13:19:54.413:93) : item=0 name=/dev/tty2 inode=24 dev=00:05 mode=character,600 ouid=flo ogid=tty rdev=04:02 nametype=NORMAL
    type=CWD msg=audit(24.07.2014 13:19:54.413:93) : cwd=/
    type=SYSCALL msg=audit(24.07.2014 13:19:54.413:93) : arch=x86_64 syscall=open success=yes exit=3 a0=0x6665a0 a1=O_RDWR|O_NONBLOCK a2=0x0 a3=0x7fffea504d00 items=1 ppid=5903 pid=5914 auid=flo uid=root gid=users euid=root suid=root fsuid=root egid=users sgid=users fsgid=users tty=tty2 ses=15 comm=login exe=/usr/bin/login key=vt2222
    type=PROCTITLE msg=audit(24.07.2014 13:19:54.416:94) : proctitle=/usr/bin/tty
    type=PATH msg=audit(24.07.2014 13:19:54.416:94) : item=0 name=/dev/tty2 inode=24 dev=00:05 mode=character,600 ouid=flo ogid=tty rdev=04:02 nametype=NORMAL
    type=CWD msg=audit(24.07.2014 13:19:54.416:94) : cwd=/home/flo
    type=SYSCALL msg=audit(24.07.2014 13:19:54.416:94) : arch=x86_64 syscall=stat success=yes exit=0 a0=0x10d4060 a1=0x7fff388a7470 a2=0x7fff388a7470 a3=0x10d4050 items=1 ppid=5915 pid=5916 auid=flo uid=flo gid=users euid=flo suid=flo fsuid=flo egid=users sgid=users fsgid=users tty=tty2 ses=15 comm=tty exe=/usr/bin/tty key=vt2222
    type=PROCTITLE msg=audit(24.07.2014 13:20:38.319:95) : proctitle=/usr/bin/Xorg.bin
    type=PATH msg=audit(24.07.2014 13:20:38.319:95) : item=0 name=/dev/tty2 inode=24 dev=00:05 mode=character,600 ouid=root ogid=tty rdev=04:02 nametype=NORMAL
    type=CWD msg=audit(24.07.2014 13:20:38.319:95) : cwd=/home/flo
    type=SYSCALL msg=audit(24.07.2014 13:20:38.319:95) : arch=x86_64 syscall=open success=no exit=-13(Permission denied) a0=0x82715c a1=O_RDWR|O_NONBLOCK a2=0x0 a3=0x0 items=1 ppid=5937 pid=5938 auid=flo uid=flo gid=users euid=flo suid=flo fsuid=flo egid=users sgid=users fsgid=users tty=tty2 ses=15 comm=Xorg.bin exe=/usr/bin/Xorg.bin key=vt2222
    Look at the last block in PATH and the block before the last. The ouid changes (owner of file) but there is no process which does this.
    Am I deciphering this right?
    Greetings

  • Only one ringtone works for all contacts despite them having separate rings

    I have 25 rings (is that too much?)
    And 33 contacts. The majority of them have their own ringtone.
    However, despite me assigning them a ringtone-- only one tone (the one assigned under "Sounds" plays for all of them.
    I didn't have this problem before.

    You said you did not have this problem "Before", before what? What changed?
    33 is no too much, I have 50-60 or so, w/o issue.
    Try Resetting the iPhone
    Reset the iPhone by holding the sleep/wake button at the top right of the device and the home button at the bottom center of the face at the same time. Hold them both until you see the screen go black and the white Apple logo appear. When this happens, you can let go - the iPhone is rebooting.
    I have not seen this issue before, so basic troubleshooting may help.

  • Finding DHCP addresses for LAN connected devices

    i am suffering from information overwhelm!
    can anyone tell me how I can find out the DHCP assigned addresses for devices that are connected to my airport extreme via wired connections to the lan?
    i have a voip box connected to the base station and i need to know it's 10.0.1.x address so that i can work with the voip company to check why that box is currently having problems.
    tia for any and all help!
    iMac G5 (PowerPC) & MacBook   Mac OS X (10.4.8)  

    You should be able to choose Logs and Statistics from
    the Base station menu and then choose the DHCP
    clients tab. That will show you all of the DHCP
    leases currently in use.
    It appears that there is a problem displaying DHCP information for wired clients.
    I discovered that if you disable the wireless (I'm only running wired clients), the Logs and Statistics tab only shows "Logs". The other tabs are not even displayed.
    When I turn the Wireless back on, the other tabs re-appear but are empty (no entries). This appears to be a bug that will hopefully be corrected in the next update
    PowerMac G5   Mac OS X (10.4.8)  
    PowerMac G5   Mac OS X (10.4.8)  

  • Can I use one email address for two apple devices? (One iPad2 and one iMac.)

    I've been trying to find this information by searching the web and I can't find a good answer.
    Can I use [email protected] for my "iPad AppleID" and use the same email address for my "iMac AppleID"?

    your mail account has nothing to do with your apple id or device or even platform
    you activate your mail account in your mail-app on your device, just pay attention you activate your account as IMAP and not as POP or Exchange
    I suppose Verizon.net offers IMAP  too?
    citation from Wikipedia :
    IMAP supports both on-line and off-line modes of operation. E-mail clients using IMAP generally leave messages on the server until the user explicitly deletes them. This and other characteristics of IMAP operation allow multiple clients to manage the same mailbox. Most e-mail clients support IMAP in addition to Post Office Protocol (POP) to retrieve messages; however, fewer e-mail services support IMAP. IMAP offers access to the mail storage. Clients may store local copies of the messages, but these are considered to be a temporary cache.

  • HT5622 We family wants to use only one apple ID for all devices ie iMac ( 4 persons sharing desktop), IPads (2nos) how we should be going about sharing same

    And how to create separate log in IDs for each person on IMac PCM.
    I am first time user of IMac,

    iCloud is not designed for multi-user use. If everyone has the same login, then they will all see the same emails, contacts, calendars and so on. If you want them to be separate then everyone needs their own Apple ID and iCloud account. Each separate iCloud account needs to be on a different device or a different user account on your Mac.
    You should be aware that any one device can create a maximum of three iCloud accounts, so with more than three you will have to set up remaining accounts on another device - you can do this from iPads so you shouldn't have a problem.

  • HT1911 My daughters ipod has been disabled and I just want to reset password for the ipod not itunes account.  We have one itunes account for all our devices (so I can control what they purchase).

    Why is itunes so difficult to navigate around?

    You will need to connect the iPod to a computer's iTunes, and you may need to put it into recovery mode : http://support.apple.com/kb/ht1808 - you should then be able to reset the iPod and restore / resync the content to it.
    If it's done via computer that it hasn't been synced to, and therefore doesn't have a backup on it, then from http://support.apple.com/kb/HT1212 :
    If you restore on a different computer that was never synced with the device, you will be able to unlock the device for use and remove the passcode, but your data will not be present.

  • How to get One Selection Screen for all queries?

    Hi Experts,
    I have three queries having selection screens. All the selection screen have the same variables, but the reports are different.
    I have created a workbook having these three queries. Each time when the workbook opens, the three selection screen pops up one after the another. Same values are entered in all the selection screens.
    Now the user wants only one selection screen for all the three reports. Is it possible? I tried but I do not see any way.
    I think there should be some way of getting it done.
    Waiting for your inputs,
    With kind regards,
    Shreeem

    Hi
    If a workbook contains multiple queries that use the same variable, you are prompted to enter the variable values again for each query. To avoid this, set the Display Duplicate Variables Only Once flag.
    Goto Workbook Settings>Under Variables Tab>select Display Duplicate Variables only Once
    http://help.sap.com/saphelp_nw70ehp1/helpdata/EN/54/a493f7256b43698191a2623e5a0532/frameset.htm
    Hope this helps,
    Aparna Duvvuri

Maybe you are looking for