Westell 7500 Wireless modem/router help please.

Hi, newbie here
I recently purchased a laptop for the first time in my life and I am trying to connect it to a wireless connection, which I have never done as well. I am using a Westell 7500 modem provided to me by Verizon. I did a bit of researched and apparently (if I'm correct) I don't need a wireless router or any other devices to get wireless internet.
If I am correct, I went to my modem's IP address and turned on wireless. I set up and changed the SSID and enabled a pass phrase, and I connected to the network at the bottom right. It connects, but there is no internet connection. What I mean by this is that it connects to the device successfully, but there is a triangular yellow warning sign with an exclamation mark on my internet bar at the bottom right and in my "Network and Sharing center" it says "no internet access."
Am I doing something wrong or do I need to buy an wireless router? Any help would be appreciated, thanks.

You do not need to buy a wireless router. the 7500 will do the job! I assume you have windows 7. OPen network and sharing center, manage wirleless networks, do you have any entries for your Verizon ISP? If yes delete the entry and go to step 2.
If no go to desktop and press f1 to bring up help - search for (Setp 2) "set up wirless network" and let us know if that works for you. Welcome to the forum
If a forum member gives an answer you like, please give them the Kudos they deserve. If a member gives you the answer to your question, mark the answer as Accepted Solution so others can see the solution to the problem. Thanks !!!
http://forums.verizon.com/t5/Verizon-net-Email/Fix-for-Missing-Inbox-sent-folders-etc-with-Internet-Explorer-11/m-p/647399

Similar Messages

How to use a Westell 7500 as a router-switch ?

I have an extra Verizon Westell 7500 DSL modem router (A90-750015-07). How do I turn it into a router-switch that will take an ethernet (not DSL) network feed (with internet access) and distribute it among a few devices and put those devices into some kind of sub-network so they see each other? I'm not using technical terms here - please teach me.
My wife is going to rent a small temporary office that provides internet access via a socket in the wall. Let's assume it's a typical RJ-45 ethernet socket. The internet speed might actually be pretty good - maybe 30Mbs down and very fast up. The total internet capacity is shared with other temporary offices in the facility, but let's assume we'll have enough for our needs.
If the only thing I bring is a single computer, I could use a J-45 ethernet cable to plug its network card directly into this socket and be done. But I'll be bringing at least two computers and a small printer/scanner. Both computers will need to share the internet access, and both computers and the printer/scanner will need to "see" each other. (Just like at home.)
So, if I plug the extra Westell 7500 into the network wall socket and then my PCs and printer into the Westell, I should get what I need here, yes? How do I do this exactly, step-by-step?
I have experimented at home and have maybe 10% success. At home, I don't have an ethernet socket in the wall, but I do have my current (not Westell) modem-router, and it has an unused LAN socket, which I am pretending is the office's ethernet socket. I connected a test computer to the Westell 7500 and logged onto the Westell 7500's embedded server (192.168.1.1), changed its VersaPort from "LAN ethernet port" to "WAN uplink port", connected the newer modem-router's unused LAN socket to the Westell 7500's E1/Uplink socket with a J45 cable, went to the Westell 7500's "Advanced" page and ran "Detect WAN Configuration". That changed the Westell 7500's "WAN uplink port Settings Protocal" from PPPoE to Routed IP. The Westell 7500 now also says its "Broadband Connection Type" is "Routed Bridge".
The test computer connected to the Westell 7500 shows it is connected to the Westell 7500, but it cannot connect all the way through to the internet. At the start, the newer modem-router shows the Westell is connected to it, and the newer modem-router has given the Westell a DHCP address of 192.168.1.5. But after a few minutes, the newer modem-router doesn't show the Westell any more. If I re-run Detect WAN Configuration on the Westell 7500, it says "Automatic Protocol Detecion is in progress" but then "DHCP server was found ... PPPoE server not found", and then the newer modem-router shows the Westell 7500 again as 192.168.1.5. But the test computer does not have internet access.
What exactly should I do with the additional settings in the Westell 7500 to make this work?
If there's a great web site to explain this to me, please point me there.
Thanks.

The answer is at
http://www.tomshardware.com/answers/id-1856344/convert-westell-7500-router-switch.html#11803251
and the links in that post.

Do you have to set up AE inBridge mode with existing wireless modem router?

Hi
I've just bought the AE and Apple TV. My plan was to basically use my existing Netgear wireless modem router for the internet only and set up the AE as the wireless router. I also bought the AE to boost the strength, print wirelessly and I thought it might work better with the Apple TV. The other things I use on my home network are ipad, iphone 4, HP DV6 Notebook, Toshiba Notebook and PS3.
I've plugged the Netgear into the AE with an Ethernet cable. I initially started with the "replace existing access point with AE", as I thought I was replacing the Netgear with the AE. This option left me with internet working and a blinking amber light on the AE.
I then did a hard reset and started again. I diabled the wireless on my old modem/router and chose the "create wireless network" option in airport utility. I think it worked because I have internet and a green light but to be honest I have no idea what I did. I know it's in bridge mode but only because I didn't know how to set up the other options.
Also, I've ended up with three networks out of this process. The default network for the AE (but it has one of those yellow error icons next to it in the available network list), the one I set up and a 5ghz of the one I set up. Neither the default network of the 5ghz network show up in the Internet and Networking control panel, which is where I delete them. I just thought this was odd.
What I'd like to know:
Do you have to set it up in bridge mode when you have an existing wireless modem/router?
If not, is there any benefit to setting the AE up as the router instead of using the Netgear?
If I create a new network should the default network still be showing up in my list of available networks or have I done something wrong?
If I have a 5ghz network, does that mean that the other network I created is only 2.4ghz or is it still dual band?
Considering the devices I have would it be beneficial for me to have a 5ghz network for certain devices only like the Apple TV?
As you can probably tell I have no idea what I am doing. I'm basically just clicking stuff and seeing if it works.
Any help/advice is much appreciated
Thanks
Jo

Hello Jo Sugden. Welcome to the Apple Discussions!
Do you have to set it up in bridge mode when you have an existing wireless modem/router?
You don't have to but, most likely, it will be the best configuration choice when you have the 802.11n AirPort Extreme Base Station (AEBSn) connected to your main Internet router by Ethernet. In this configuration, all NAT & DHCP services will continue to be provided by the Netgear router. This will allow all wired or wireless clients connected to the AEBSn to get their IP address (and be on the same subnet) from the Netgear ... and this would allow clients connected to either router to "see" each other.
If not, is there any benefit to setting the AE up as the router instead of using the Netgear?
If, for some reason, you wanted to create a separate subnet, configuring the AEBSn as a router would allow for this.
If I create a new network should the default network still be showing up in my list of available networks or have I done something wrong?
By default, your AEBSn will create two wireless networks with the same Network Name; one broadcasting in the 5 GHz band, and the other in the 2.4 GHz band. The default name for both of these will be Apple Network NNNNNN. You have the option, within the AirPort Utility, to change the names of each network.
When connected by Ethernet, and in bridge mode, it would be beneficial to name your AEBSn's networks the same as that provided by the Netgear. This would create what is called a "roaming" network ... where you literally can roam with a laptop from one router to the other and still be on the "same" network. This also is a way to extend the wireless range of the Netgear.
If I have a 5ghz network, does that mean that the other network I created is only 2.4ghz or is it still dual band?
As a minimum, you will have three wireless networks: one provided by the Netgear and two provided by the AEBSn. By giving them all the same Network Name, they will appear as one to any wireless client. However, they will all show up in a utility like iStumbler or AirRadar.
Considering the devices I have would it be beneficial for me to have a 5ghz network for certain devices only like the Apple TV?
Yes. Operating a wireless network in the 802.11n Radio Mode in the 5 GHz Radio Band offers the best potential bandwidth ... around 300+ Mbps. The only real drawback of the higher frequency band is that the signal strength drops off more rapidly with distance than in the lower frequency band. Also higher frequencies cannot penetrate objects (like walls) as well.
Ideally, you would want to place your Apple TV or other streaming devices in the same room as the 5 GHz network ... or connect them to the router by Ethernet.

Old printer with new wireless modem/router

i just installed a new wireless modem/router and need to get my printer to work with my comps....i think i need to reassign the IP address and enter the wep...but dont know how

Hi dduve,
Set up a static IP address for your printer, click here and follow the steps in this document to set one up. Let me know if you need more help.
I worked on behalf of HP.

Configuring a new Airport Extreme with an existing Wireless Modem Router

I have an existing Wireless Modem Router (brand: Riger) and have an existing wireless network. Recently purchased an AirPort.
What is the best way to install a new AirPort Extreme? I know i have to connect the AirPort Extreme to the modem via ethernet cable.
Do i allow the AirPort to use the existing setting from my old wireless modem router?
Or do i create a new network with different name and password?
Anybody can help or show me where i can look up on this?
Thanks

Hello akramaziz. Welcome to the Apple Discussions!
Since the new 802.11n AirPort Extreme Base Station (AEBSn) will be connected to the existing Wireless Modem Router by Ethernet, it should be reconfigured as a bridge.
(ref: AirPort Utility > Select the AEBSn > Manual Setup > Internet > Internet Connection > Connection Sharing = Off (Bridge Mode))
As a bridge, the AEBSn will allow the existing router to continue to provide both NAT & DHCP services for all network clients.

I recently bought an external hard drive and attached it to a wireless modem router. The problem is that i can't access it from my macbook. I get a "connection failed" and "the server is available on your computer. Access the volumes and files locally".

Well I believe I described the problem above. I want only to add that the external hard drive is a Seagate FreeAgent GoFlex Drive 1TB and the wireless modem router is a Belkin N Plus (model F5D8635-4 v1). Also, in the finder window under "shared" I see a "belkinserver" and when I click it, it says "connection failed". If I click "connect as" I get the "the server "belkinserver" is available on your computer..." which I mentioned above. I tried to connect macbook via ethernet to the modem router and then when I typed "smb://belkinserver" it immediately prompted me for a username and a password and when I typed them finally I got to enter the contents of the hard drive! So what's the problem wirelessly?

If your external drive does not have an independent power supply, you may wish to consider a couple of lower-cost options before tossing the drive. Bus-powered drives have no external power source and must get all their power from the computer. They can exceed the computer's USB energy budget.
Cheapest option:
1 Meter USB 2.0 A to 5 Pin Mini B Cable - Auxiliary USB "Y" Power Design for external hard drives.
This gets power from two of the computers USB porst sna can provide enough power to wake up an under-performaing bus-powered drive.
If you don't have enough ports to use this, try the next cheapest option:
Newer Technology 7 Port Hi-Speed USB 2.0 Hub with Power Adapter for Mac & PC
Such a hub has a an independent power supply to make up for wahat the comptuer fails to provide.

Time Capsule and Wireless Modem/Router

I have recently just moved. In my old apartment I have my time capsule connected to my modem that was not wireless, and I was using it creating a wireless network and backing up my mac book pro.
Now that I have moved, my new cable company has supplied me with a modem and wireless router in 1. It creates its own wireless network.
The internet works fine on the network supplied by the new router. When I plug in my TC into the router (using a ethernet cable) it still backs up my mac book, however the light still flashes and still wont connect or make a new network.
I am wondering what is the best way to set up my new wireless modem/router with my time capsule:
Should I leave as is with it still backing up my macbook or is there a better way to set it up so I have my own mac network supplied by the TC, as well as the current one supplied by the company router?

You have a choice here..
The simple way to set this up is bridge the TC.. I think that is how it must be setup otherwise your Mac could not back up to it.
The fact that the wireless network of the TC is unavailable is not a major issue unless the current router is slow.
You can do a reset of the TC.. I recommend to still download and use 5.6 utility
http://support.apple.com/kb/DL1482
Still far superior to the one in Lion. You might need to do it at first with ethernet directly to the TC and set up wireless again.. use short name with no spaces no special characters. Fix and lock the 2.4ghz wireless channel.
Go to the internet tab, connection sharing and make sure the connection sharing is set to off bridge mode.
Once you do that, plug the TC back into the main router by ethernet.. reboot the whole system.. restart in order modem.. tc.. clients. It should now appear as TC wireless network.
The alternative is to turn off wireless or even bridge the modem router and use the TC in router mode. You will need to look up how to do that. That would make the current modem just like your old one which was a straight pure modem.. but you can easily run into trouble so I think it is not the best option here.

Using Airport Extreme (802.11n) with Netgear Wireless Modem Router

I have a quick question, can I use the Airport Extreme in a wireless modem router?(http://www.netgear.co.uk/wirelessadslrouterdg834g.php)
By plugging the Airport into the Netgear router would I be able to by pass and run a network this way. I have a 802.11n enabled MacBook and Apple TV, the Netgear is the weakest link!!!
Many thanks.

neptune2000's post was implying that you connect the AirPort Extreme base station (AEBS) to the Netgear.
The AEBS does NOT contain a modem. Therefore you will need a modem, either the Netgear or another.

I cannot retrieve the password for the wifi connection on my imac and so cannot access the internet with my ipad at home. I have a cable modem. Help please!

I cannot retrieve the password for the wifi connection on my imac and so cannot access the internet with my ipad at home. I have a cable modem. Help please!

If you mean that you cannot remember the password for your WiFi network this will work for you - or it should work if you are the administrator on the Mac.
You will need to be logged in as the administrator on your Mac and you must know the password - Open Keychain Access on your Mac in the utilities folder, click on Passwords. Find the Airport Network Password listed on the right. Double click on it. Click on show password in the the window that pops up. Enter your administrator password when prompted and click allow.
If Keychain is locked - you must enter the administrator password there as well to unlock it and access the password.
If you have set the Mac up for Internet Sharing for the iPad to share the Mac's connection, just create a new network On the Mac with Internet sharing and a new password.

Using Westell 7500 DSL Modem as Secondary Router with Actiontec Router?

Hi, I had just recently switched to Verizon FiOS internet from Verizon DSL service, and I'm happy with the service so far. But I have found the range of the Actiontec router to fall short of what I need it to be. I was wondering whether anyone here has tried repurposing the Westell 7500 modem as a secondary router?
I spent the better part of two days looking up ways to do this and couldn't find anything regarding my specific situation. I know one can repurpose a DSL modem as a router to be used with a cable internet modem (have not done this myself), and I also stumbled upon this FAQ (http://www.dslreports.com/faq/12506) on how to connect a secondary router to the Actiontec router. However I couldn't find anything specifically regarding the Westell modem. I've tweaked many settings in the modem without success.
Is this even possible?
Thank you.
Solved!
Go to Solution.

#1 You logged into your primary router, found the DHCP range, and re-adjusted it as need be (From step 1 to step 5) of http://www.dslreports.com/faq/12506 ?
#2 If not, do that first.
#3 If so, great.
If the Westell is using the Red and Black Firmware - In the Westell..
a) Select the My Network icon, then select Network Connections from the left menu.
b) On the Broadband Connection screen, click the word LAN
c) On the next screen remove the checkmark from Private LAN DHCP Server enable.
d) Where it says Modem IP Address, make that IP Address outside of the primary router's DHCP Server Range.
For exampe if the Primary router's IP Address is 192.168.1.1, the Starting IP Address is 192.168.1.11, the Ending IP Address is 192.168.1.254 - then you could make the secondary router's LAN IP 192.168.1.2
e) Click Apply or Save Settings.
As addressed on http://www.dslreports.com/faq/13600
there is also the White and Blue firmware.
If your Westell looks more like the sample screens that you see at
http://myplace.frontier.com/~paradise.cowgirl/6100.htm
Then
a) In the Westell select Configuration and select Private LAN Connection.
b) Uncheck Private LAN DHCP Server Enable
c) Where it says Modem IP Address, make that IP Address outside of the primary router's DHCP Server Range.
For exampe if the Primary router's IP Address is 192.168.1.1, the Starting IP Address is 192.168.1.11, the Ending IP Address is 192.168.1.254 - then you could make the secondary router's LAN IP 192.168.1.2
d) Click Apply or Save Settings.
Please note this only how to convert a router (including a DSL modem) into acting as a Hub/Switch/Wap.
This is not how to use this device as your primary router with any broadband type of device that is not (or can not be) configured to handle the public IP.
For example, not how to have a Westell 6100 be in bridge mode (bridge-bridge, not bridge-routed bridge or not PPPoE) and have your Westell 7500 handle the public IP (bridge-routed bridge or PPPoE).
If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it. If anyone has been helpful to you, please show your appreciation by clicking the "Kudos" button.

Can Westell 327W DSL modem/router receive wireless signal?

I have a spare Westell 327W wired/wireless DSL modem/router. I need a wireless access point for a G4 Power Mac away from an Apple Extreme. I knew how to make the Westell 327W in a bridge mode. Is there a way to make 327W communicate wirelessly with a FIOs modem/router?
Thank you very much.
Robert

Hmmm, perhaps something like this with a USB extension cord would be a solution, they have better Range even without an extension than Airport cards ime...
http://eshop.macsales.com/Item_XLR8YourMac.cfm?ID=10303&Item=NWTMXP802NU2C

Airport Extreme and Netgear DGN2200 Modem Router - Help

Hi everyone,
I’m from Italy, sorry for my English. I hope I will explain my problem well enough.
In some weeks I gonna buy my first iMac (after years and years on Win-PCs). For Christmas my family gave me an Airport Extreme for present. This is the first Apple product that comes into my house (..not really an happy entrance until now).
I’m just getting mad about setting this Airport Extreme. I would want to use it as a wireless extender ; I tried almost all possible setups searching for days on the web , but nothing. It doesn’t work. The Apple assistance is always busy in the hours I can be at home and the Extreme still remains a well-done-elegant white brick on the desk..
Situation:
-     I’m working on a Windows PC now (Windows 7)
-     I use a Netgear Modem wireless Router DGN2200 plugged via Ethernet cable to the PC
-     I downloaded Airport utility for windows 5.6.1
-     The Airport Extreme is new (5th generation)
My wish:
-     Using the Airport Extreme in another room of my house connected wirelessly to my existing Netgear router, as an extender of the network
Problems that I found:
-     Wirelessly the base is not found by Airport utility
-     To find the base I have to plug an Ethernet cable from the Netgear Router to a port on the Airport base, but not the first WAN port, I have to use one of the others.
-     When I find the base I try setting-up it with the Bridge Mode, but then it gives errors 6753 or 10057.
-     I tried to change settings on the Netgear Router or reset them, but nothing ..
and so on many tries.
If someone of you had the same Netgear Modem Router (DGN2200) and use an Airport Extreme base like an extender in bridge mode, please tell me what configuration, in the Router Modem and on the Airport base, works fine.
Thank you very much in advance.
Best regards.

I can only create a “New Wireless Network” (no bridge mode) connected to Netgear Modem Router by Ethernet cable , in this way I would have 2 networks, one from the Netgear and another from the Airport, but the source of wireless will be in the same room (because they will be connected together by cable).
I already provided the instructions for this in my post above. Here they are again:
Configure the AirPort to "create a wireless network" using the same wireless network name, same wireless security and same wireless password as the Netgear network....and...configure the AirPort Extreme in Bridge Mode to work correctly on the network.
If you do this, then the AirPort and Netgear devices will work together to act like one "big" network. That is because you have two routers producing the same network.
If I bought 2 Powerline extenders, one connected close to the Netgear Router and the other one connected to power line in the other room,
could I connect by cable the Airport Extreme to the second extender
If you cannot connect an Ethernet cable from the Netgear to the AirPort Extreme, then you might be able to use a pair of Ethernet powerline adapters to send the signal over the AC wiring in your home.
I have not found powerline products to be reliable in general when I have used them, so make sure that you understand the store's return policies in advance if you decide to try them.

Best wireless modem/router for Comcast internet service?

Hello!
I am looking to switch internet service from Verizon DSL to Comcast. I have a MacBook Pro using Airport Extreme (supports 802.11 a/b/g/n), and my other computer is an iMac (OS 10.5.8, iMac 6,1), with a printer and a Roku box (I'm also thinking about switching to Apple TV). All are currently set-up wirelessly with a combined modem/router.
I know that there is a list of a bunch of potentials on the Comcast website, but I'm looking for real experience from Mac users. Good, bad or neutral comments are appreciated.
Thank you!
Ken

Don't pay Comcast monthly for a router. Buy a router. A router is a router, the best routers are Cisco based rackmount devices. Honestly the AirPort Express and Extreme are amazing and work quite well with Apple products. Plus if you purchase one and get AppleCare on it you get AWESOME support from your friendly AppleCare advisors... sure as **** beats going to India and talking to Fred.

WIreless Modem/Router and Phone service

I am ready to install wireless gateway, but I have 3 phones one with cord and two cordelss. If I use wireless gateway for phone service will I lose access to those phones not plugged into the modem/router?

Hello,If all phones are connected via that single RJ11 (Phone Cable) then you should be set. Everything needs to be directly plugged into the modem, or via a splitter. Your cordless phones base-station needs to be connected to the Gateway to operate.

Lynksys E900 Wireless-N300 Router - Help needed to share internet connection from PC to home network

Hi, I'm hoping someone can help me out with a problem I have:
I am currently connecting my PC to a mobile phone as a Wireless Access Point to give that PC access the internet. I also have a small home network, with one other PC and a Game Console. I own a Linksys E900 Wireless-N300 Router. My problem is this. How do I share that internet connection with the rest of the home network?
To the best of my knowledge its not possible to connect my mobile phone directly to my Linksys E900 Wireless-N300 Router, although if anyone has any ideas how to do this I'd love to hear!
So my alternative idea is to connect to the internet via one PC, set up that internet connection as "Shared." and then allow the other devices on the home network to connect thru this. My question is how do I set up my Linksys E900 Wireless-N300 Router to allow my other PC and game console connect to the internet? Bridge Mode? PPPoE? Any help or suggestions would be greatly appreciated! PS: both PC's are running on Windows 8

I have Cisco Linksys E900 router. I want to make my home Wi-Fi zone. But I don’t have Static IP. One more thing is that Service provider have web page Authentication. I have username and pass.
I am able to make SSID and security for my WI-FI LAN. I can use internet on one device. If I tried from second device again it’s asking me for username and password. While login it’s showing your first session in not logout. (Means I have to logout from 1st device and have to login on 2nd device.)
Is there any option that I can Use my all devices at same time?

Westell 7500 Wireless modem/router help please.

Similar Messages

Maybe you are looking for