WET160N - Bridge between wireless equipaments e wire local network

Hi,
I want buy the WET160N to make a bridge between my wireless equipaments e my wire local network (same network address 192.168.1.0/24) but, before buy, I would like to know if the WET160N can make a bridge between wireless equipament and my wire local network using the some network address.
ps.: I don't want use the wifi router or gateway, just a bridge.

Yes you can use WET610N and make it work as a bridge between your Wired and Wireless equipments.

Similar Messages

Express as bridge between ethernet-linked computer and Extreme network?

I know similar questions have been asked before, but I just wanted to double-check before buying an Airport Express. So, thanks for any help ...
I currently have a wireless network at home, facilitated by an Airport Extreme (the most recent model, with internal modem).
I also have a PowerMac G4 ("mirror door drive"), which is too old to take an Airport Extreme card.
The PowerMac and the Extreme are too far apart to easily connect by ethernet.
I was hoping to buy an Airport Express which I could connect to the PowerMac via ethernet, and therefore have my computer talk to the Extreme network via the bridged Express. A bit like having an external wireless "card", instead of an internal one.
I believe this is possible, if both Express and Extreme have "WDS" enabled? And that it'll work despite the fact that Apple tech support habitually claim that it doesn't?
Also, if it does work, does anyone know if my computer should display the modem dial-up "uptime" when connected? I know that computers that are wirelessly connected to the Extreme DO display this, but if a computer is connected to it via ethernet, it doesn't (which doesn't make sense to me, but there you go...)
Thanks very much for your help on this! And sorry if this is a repeat question. Even the Airport Express is a lot of money, if it turns out not to work as I hoped.
Having spoken to Australian Apple tech support several times, I get the impression that they're not even based on the same continent as me, and seem to be bluffing that they can even understand me fully. So I'm afraid I don't have much confidence that what they're telling me is true.
Cheers,
Wayne

Currently I connect directly to an Airport Extreme
via ethernet, and that doesn't seem to facilitate
that, for some reason, even though computers that
connect to it wirelessly can see the uptime.
Missed that.
Running a non-Airport Mac and using dial-up internal modem on the AEBS and can not hang up
http://www.ifelix.co.uk/tech/1005.html
The Java utility has a timer as well.
iFelix

Wireless Bridge between WAG120N and E1500

I have my internet coming into my WAG120N and going out wirelessly. I want to setup a wireless bridge between this and an E1500, so I can connect my TV to the E1500 (via an ethernet cable) and have it access the internet. Unfortunatly I can run a cable from the WAG120N to where the TV is. So it I can get the E1500 wirelessly bridged to the WAG120N, I hope I can get around this issue.
I have updated the firmware ont he E1500 to get Bridging support, but from what I can tell it only provides bridging via an ethernet cable. Is there away to bridge wirelessly?
Cheers
Mike
Solved!
Go to Solution.

1. Linksys wireless routers don't support wireless bridging.
2. Either install 3rd party firmware like dd-wrt or tomato or buy a dedicated wireless bridge and connect the E1500 to the bridge. That way you can also use the wireless in the E1500 for wireless connections.
3. Otherwise check power line ethernet. That's often a better and more reliable solution.

Wireless Bridge between 2 building

Hi !
I need a wireless bridge between a second building (across the street, about 100' direct) to our main building and a switch.
Can anyone recommend me a good products/solutions.
The purpose of this bridge is to connect the remote office via a small Cisco Switch with 6 computers, and 6 IP Phones w/video.
Thanks !

The 1300 comes in two flavors, one with internal antenna and the other with external antenna connectors. For the distance you indicated I would use the internal antenna model, it is rated for up to 1.25 miles and requires less accuracy in alignment than the YAGI antenna. I believe the spread of the signal is 15 degrees on the built in antenna.
The YAGI could be used with the external antenna model but will limit your exterior coverage for users other than the remote bridge.
Seth

Setup of bridge between 2 AIR-AP1262N-E-K9

The conduit between the core cabinet and access wire centre was accidentally damaged and no F/O cables can be pulled through for connection. I now need to setup bridging between two Air-AP1262N-E-K9 wireless devices. As I do not know the technology at all I need some help with this please.......

Hi Jerome,
The 1310 definitely can work with the internal antenna but... is the AP mounted somewhere? Some mounting options imply an external antenna as they position the internal antenna toward the wall...

Wireless Equipment for 1 or 2 Km.

Hi,
I'm trying to connect two places for my customer, the distance is 1 or 2Km.
What model of wireless equipment I can use for this link ?.
We'll have, VoIP, Video and data.
Do you have any recommendation ?.
Thank you.

First, you can probably use 1242 APs with patch antennas, but if the distance is more than 1km, it will probably not work.
Next is a 1300 series with an integrated antenna. Before selecting this bridge, I would suggest you make sure that there is little or no interference in the 2.4 GHz range at both of your locations (Has only G radio). AIR-BR1310G-A-K9 part number.
Last and best, are the 1400 series with an integrated antenna, we have had no issues with those running at 8 miles. (54mbps 28dBi dish). AIR-BR1410A-A-K9 part number. This is a 5.8 GHz bridge.
For either 1300 or 1400, make sure to order proper length power injector cables and any other accessories:
http://www.cisco.com/en/US/prod/collateral/wireless/ps7183/ps469/product_data_sheet09186a008022b11b_ps5279_Products_Data_Sheet.html
Also, check out the calculator utility:
http://www.cisco.com/en/US/prod/collateral/wireless/ps5679/ps5861/prod_technical_reference0900aecd800f9155.xls

Bridge between airport card and ethernet port

My son wants to access the internet through the ethernet port to connect his xbox 360. My airport extreme base station is upstairs and my powermac g5 is in the basement and connects to the internet through the airport network (airport extreme card to base station). One of his friends says he can configure a bridge between his wireless card and his ethernet port on his windows computer and was trying to do it on my mac. Can a bridge be configured between the airport extreme card and the ethernet port on the g5 which will allow an ethernet device to connect to the internet? Any advice will greatly appreciated. Thank you.
Larry

I have used an external ethernet bridge in the past. What I am wondering is: How can the airport card be configured to create a bridge to the ethernet port on the computer, so the game console could be connected to the back of the g5 with an ethernet cable and then connected to the tv with a/v cables. Do I have to use some external device to provide an internet connection to the game console or is there some way to share the connection from the airport card to the ethernet port?

Configure a Bridge between Websphere MQ 6.0(MQSeries) and Weblogic9.2

Bridge between Websphere MQ 6.0(Previously MQSeries) and Weblogic 9.2
At Websphere MQ 6.0 side:
³ Create a folder by the name JNDI-Directory under C drive
³ Create the queue manager by using the command at the command prompt:
crtmqm testqmgr or you can create it by GUI also.
³ Start the queue manager: strmqm testqmgr. or you can start it by GUI also
³Define Local Queues in the newly created queue manager testqmgr by using GUI or by using Commands .Assume we have created a local queue by the name MyMDBQueue.
³ Create a file by the name MyAdmin.config,It¡¦s a configuration file under C:\Program Files\IBM\WebSphere MQ\Java\bin directory.
Now add the following entries into the config file
INITIAL_CONTEXT_FACTORY=com.sun.jndi.fscontext.RefFSContextFactory
PROVIDER_URL=file:/C:/JNDI-Directory
SECURITY_AUTHENTICATION=none
Without the above step also you can do that. How it means
You have a file called JMSAdmin.config under C:\Program Files\IBM\WebSphere MQ\Java\bin directory.jsut uncomment the above mentioned 3 properties and comment the remaing that¡¦s it.
Next run the below command
C:\Program Files\IBM\WebSphere MQ\Java\bin>JMSAdmin.bat ¡Vcfg MyAdmin.config
Once you run the above command you will see
this prompt InitCtx>.
Now your command prompt will stop at
InitCtx>
Just type the following commands
a) InitCtx> def xaqcf(SenderQCF) qmgr(testqmgr) press enter
b) InitCtx> def q(MyMDBQueue) qmgr(testqmgr) queue(MyMDBQueue) press enter
c) InitCtx> end press enter
At step a it will create a queue connection factory by the name SenderQCF UNDER QueueManager testqmgr
At step b it will create a queue by the name MyMDBQueue UNDER
QueueManager testqmgr
At step c Its ends the Context cration process
At Weblogic 9.2 side:
Go to your domain location lib folder i.e. In my system it¡¦s in C:\bea\user_projects\domains\bplus_domain\lib. Add the following jars in lib folder
1) com.ibm.mq.jar
2) com.ibm.mqjms.jar
3) commonservices.jar
4) connector.jar
5) dhbcore.jar
6) fscontext.jar
7) jms.jar
8) jta.jar
9) ldap.jar
10) postcard.jar
11) providerutil.jar
Now restart the weblogic server. now the server reads all the jars
Open console of weblogic9
Go to Services³Messaging³Bridges³Jms bridge destination. under this create new
jms bridge destination.
Source of jms bridge destination:
Adapter JNDI Name: eis.jms.WLSConnectionFactofyNoTX
Classpath:<optional>
Connection URL: file:/C:/JNDI-Directory
Initial Context Factory: com.sun.jndi.fscontext.RefFSContextFactory
Connection Factory JNDI Name: SenderQCF
Destination JNDI Name: MyMDBQueue
Destination Type:Queue
User Name: <optional>
User Password: <optional>
Confirm User Password: <optional>
Now activate the changes what you have made
Destination of jms bridge destination:
Adapter JNDI Name: eis.jms.WLSConnectionFactofyNoTX
Classpath: < optional>
Connection URL: t3://localhost:7001
Initial Context Factory: weblogic.jndi.WLInitialContextFactory
Connection Factory JNDI Name: ConnectionFactory1
Destination JNDI Name: ResponseQueue
Destination Type:Queue
User Name: < optional>
User Password: < optional>
Confirm User Password: < optional>
Now configure a new Bridge by using above configured two source and destination
jms bridge destinations
At source you have to select Other JMS.don¡¦t select Weblogic7 or Higher because the source of this bridge is WebsphreMQ, not weblogic
Now once again RESTART The weblogic9.2 serever and put one message on WebsphreMq queue and check whether it reaches the destination queue of weblogic
Enjoy the session

Is this working for you? What errors do you get in the logs (bam, EL)?

Home Sharing not working between wireless PC's / devices and ethernet wired PC's on the same router.

Home Sharing is not working between wireless PC's / devices and ethernet wired PC's on the same router. I installed a new Verizon FIOS ActionTec MI424WR GigE wireless / ethernet router, replacing the original FIOS router. With the old router Home Sharing worked fine across and among all iOS and Windows wired and wireless devices. With the new router Home Sharing works between and among the Wired PC's but not between the wired PC's and the Wireless connected PC's or iOS devices. Home Sharing also works between and among the wireless connected PC's and iOS decices but not between them and the wired PC's.
Only the router was changed. No changes were made to any of the devices except all were updated with the latest version of iTunes 10.7.0.21 and the iSO devices were updated to iOS vrsion 6.01. Three PC's are wired and all are running Windows 7. There also is a Windows Home Server connected to the router by ethernet port. It does not run iTunes but does provide WebDAV services to my iOS devices. This works fine. Two PC's are wireless, one running Windows 7 and one running Windows 8. All of the PC's are connected to the same (new) router via it's ethernet ports and it's wireless access point. Two of the wired PC's are connected via a high-speed ethernet hup that is connected to the router (Home Sharing works fine between the two PC's on the hub and the PC on the router). All wired and wireless devices on the router are visible and members of the router's Home/Office virtual network.
All of the PC's are visible in the Windows network and all shared files are accessable from all PC's, both wired and wireless.
Obviously the router seems to be the issue, something between the ethernet and the wireless access point components. I checked the settings and found nothing that would prevent Home Sharing between the wired and wireless devices. There is no setting that isolates the wireless network. I have done the following:
Read the router user manual and checked all the settings
Rebooted the router and tested.
Turned off the router's firewall and tested.
Home Sharing is turned on all the devices and all use the same Apple ID.
Restarted iTunes and tested.
Verified iTunes is "Allowed" in each PC's firewall.
Again, I can Home Share between the two wireless PC's but not between either of the wireless PC's and any of the wired PC's. I can Home Share between my iPads and iPhones and either of the two wireless PC's but not with any of the wired PC's. I can Home Share between any of the wired PC's but not between any wired PC and a wireless PC or iOS device.
I hope someone may have had a similar problem and has a fix suggestion. I'm stumped! I have a;so contacked ActionTec and awaiting an answer.

Solution from ActionTec is:
Log into your router.
Click the Advanced icon
Cclick Yes
Click on the IGMP Proxy
Select Disable
Click Apply

CISCO ASR901 BRIDGE BETWEEN 2 INTERFACES

Hi All!
I'm looking for some way to make a transparent bridge between two interfaces of a Cisco router ASR901 , is there any possibility? I ask this because I have a scenario where I would use the ASR901 to the following question :
POP01 (                       ) ASR901 g0 / 6 -------- > ISG_7206
POP02 ( MPLS CLOUD )               g0 / 7 -------- > ISG_7206
POP03 (                       )
The ASR901 will focus EoMPLS with other points in the network and pass on to ISG routers , ie , VLANs would have to be two ports with XConnect to a remote router , the configuration would be something like this :
interface GigabitEthernet0/6
Core description : MPLS CONC PPPOE02
no ip address
negotiation auto
hold- queue 1024 in
hold- queue 1024 in October
service instance 4095 ethernet
encapsulation dot1q 4094
rewrite ingress tag pop 1 symmetric
interface GigabitEthernet0/7
Core description : 7206_PPPOE_01
no ip address
negotiation auto
service instance 4095 ethernet
encapsulation dot1q 4094
rewrite ingress tag pop 1 symmetric
end
L2VPN XConnect context TEST
ethernet interworking
member 201.55.127.202 1212 encapsulation mpls group TEST
member GigabitEthernet0 / 7 service -instance TEST 4095 group priority 1
member GigabitEthernet0 / 6 service -instance 4095
redundancy group delay 1 3 TEST
But without an interface that was redundant of other , what I need is the 2 interfaces in " bridge " making a XConnect to a remote router , and these 2 interfaces connected ISGs in 2 to make a balance .

Hi,
This discussion is for IOS-XR related questions. You should post your question under Service Provider > MPLS.
thanks,
rivalino

CISCO ASR901 BRIDGE BETWEEN 2 INTERFACES WITH XCONNECT

Hi All!
I'm looking for some way to make a transparent bridge between two interfaces of a Cisco router ASR901 , is there any possibility? I ask this because I have a scenario where I would use the ASR901 to the following question :
POP01 (                            ) ASR901 g0 / 6 -------- > ISG_7206
POP02 ( MPLS CLOUD )                   g0 / 7 -------- > ISG_7206
POP03 (                            )
The ASR901 will focus EoMPLS with other points in the network and pass on to ISG routers , ie , VLANs would have to be two ports with XConnect to a remote router , the configuration would be something like this :
interface GigabitEthernet0/6
Core description : MPLS CONC PPPOE02
no ip address
negotiation auto
hold- queue 1024 in
hold- queue 1024 in October
service instance 4095 ethernet
encapsulation dot1q 4094
rewrite ingress tag pop 1 symmetric
interface GigabitEthernet0/7
Core description : 7206_PPPOE_01
no ip address
negotiation auto
service instance 4095 ethernet
encapsulation dot1q 4094
rewrite ingress tag pop 1 symmetric
end
L2VPN XConnect context TEST
ethernet interworking
member 201.55.127.202 1212 encapsulation mpls group TEST
member GigabitEthernet0 / 7 service -instance TEST 4095 group priority 1
member GigabitEthernet0 / 6 service -instance 4095
redundancy group delay 1 3 TEST
But without an interface that was redundant of other , what I need is the 2 interfaces in " bridge " making a XConnect to a remote router , and these 2 interfaces connected ISGs in 2 to make a balance .

Hello,
I do not believe that the ASR901 will do this without help from an upstream device. If I understand correctly, you want to build a bridge-domain with 3 EFPs: 2 physical ports, and one pseudowire. As of the last IOS revision that I have configured on this platform, the 901 doesn't support the pseudowire on a bridge-domain, only a service instance.
It seems to me that you would need an upstream box involved to support this.
Either:
Build 2 pseudowires to an upstream box that supports this configuration (like an ME 3600x, ME3800x, or 9k).
or
Associate both service instances to a common bridge domain that is extended to an upstream box that is initiating the pseudowire. More platforms would support this, since it does not require supporting the pseudowire on a bridge domain.
...Unless you are looking to build an LACP channel-group on the interfaces connected to the ISGs to load-balance. The 901 supports LACP, and it also supports building an EFP (service instance) on the channel-group interface. This technically makes the 2 physical interfaces one EFP. The part of this that I have not tried is building a pseudowire on an EFP on a channel-group.
Hope this helps.
Jason

Wi-fi bridge between two routers TP-LINK WR841ND (WDS). HP 1536 dnf MFP connect to one of this routers (copper). My Ipad or Iphone can't find HP 1536 dnf MFP (using Eprint). Ipad and iphone connect to router across WiFi.

Hello.
I have wi-fi bridge between two routers TP-LINK WR841ND.
The name of this technology - WDS.
HP Laser JET 1536 dnf MFP connect to one of this routers (copper).
Second device (my NETBOOK) connect to second router (WiFi).
I have good communication between NETBOOK and HP Laser JET 1536 dnf MFP via WiFI-bridge.
In usual case NETBOOK can find (and can Ping) network printer and make a print some files.
But my Ipad or Iphone can't find HP Laser JET 1536 dnf MFP (using Eprint). Ipad and iphone connect
to router across WiFi.
Please, help!

Are you using the ePrint Mobile App, the ePrint Printer Control App, or just trying to send an email to the printer's ePrint email address?
Does AirPrint work?
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

Connection between Wireless network (shared) and wired network through a router/modem

I have a windows 8.1 X64 installed on my pc. i have connected a USB wireless network adapter to it so that i can connect to another wireless
network. my internet connection comes from this device as well.
I've got a Modem/router/AP (TD-W8970) and i set it up to work as wireless router with DHCP server enabled. i wanted to share my internet
connection that comes from wireless network adapter in home so i did the followings:
1. connected the WAN port of my router to the Ethernet port of my PC.
2. in windows' network adapter settings i shared my wireless network adapter's connection with the Ethernet port.
now i can connect with my laptop to my wireless router and use internet connection that is being shared by PC's wireless adapter but i
can't connect to the PC in order to have a home group with it or use the shared files/folders in PC.
More Details:
Wireless network adapter local settings:
IPv4 Default Gateway/ DNS server/ DHCP server = 192.168.1.1
IPv4 address: 192.168.1.4 - IPv4 subnet mask: 255.255.255.0
Ethernet
port settings:
IPv4 address: 192.168.137.1
IPv4 subnet mask: 255.255.255.0 .
my question is how to make that connection like a LAN and what configuration do i need to apply on both router or PC.
Thanks in Advance!

Hi,
Please try the following steps for test to configure your network sharing.
1. Open CMD, type ipconfig/all. Then remember USB wireless card DNS server address.
2. Open Network Connection, Change Adapter settings, USB adapter properties, check network sharing.
3. Open Local network connection, generally speaking, Router's default lan address is 192.168.1.1, you can asign the desktop PC IP as 192.168.1.2.
4. Access into Router management interface, then enable router's DHCP service. Set its gateway same as sharing host address, DNS server same as USB wlan's DNS server address.
Roger Lu
TechNet Community Support

Communicating between Air apps on local network?

I am trying to build an AIR application that allows communication on a local network only. Can I use the Local Connection to achieve this or is that only to communicate between apps on a single machine. The functionality I am trying to achieve is simple check in/out app to let users know when someone is already working in a folder. I already have the functionality built for this, I just need to be able to broadcast events to another AIR app on a local network. Can anyone help or shot this down? Thanks in advance.

You are right: you can only use LocalConnection for communication between AIR applications (and SWF content in browsers) on a single machine.
You may want to build a server application that the other AIR applications communicate with via a socket connection.

Bridge between DropTarget and TransferHandler

Bridge between DropTarget and TransferHandler
Hypothetically, what if you have:
1) old code which uses a DropTarget to tie together a JEditorPane and a DropTargetListener
2) the desire to set on newish GUI code a TransferHandler. It�s a custom GUI TreeTable component that I want to be the source of the data only (COPY).
When I tried to mock something up and drag something from the new GUI to the old GUI, I did not see a Transferable set in the DropTargetDropEvent of the drop method
Thoughts? Has anyone ever done such a thing before? Google did not reveal much.
The mock up code I have is intertwined with the system so I cannot share it.
Thanks.

Try setting a breakpoint in the listener method and see if the event is recognised.

WET160N - Bridge between wireless equipaments e wire local network

Similar Messages

Maybe you are looking for