WGB Issue

Hi;
I am having the 4402 wireless lan controller running with 7.0.116.0 code and LAP 1250 and WGB 1250. I configured the WGB AP with the mobility fine tuning commands. But sometimes the WGB and its clients cannot be pingable. If we trying with console , from the dot11 associations we can see that its already connected to the parent and dot1radio is up. Did any one come across with the issue and whats the solution.

What kind of clients are behind the IE3000's? Are they passive?
The proper way to work with the passive clients is putting their MAC address in the Mac Filtering in the WLC and enabling the "passive client" in the WLAN.
Then you enable L2 bridge forwarding on the 1300 with the "bridge 1 addressxxxx.xxxx.xxxx forward FastEthernet0" command.
Then you add a static arp entry in the L3 switch that the SVI resides on.
When you don't have connectivity to 1300. Keep a ping going to it and then try to ping it from your IE3000. If it starts pinging from you computer immediately after that - it sounds like you have an ARP issue.
Is it possible to post the configs of the IE3000's and 1300's?

Similar Messages

  • ISSUE on Mesh with WGB

    Dear all,
    We have issues with our mesh network, we have a 2 WLC 5508 ver7.0.220.0 (connected to 3560 with LAG) 16 APs1524, 60 Bridges 1300 ver12.3.8-JA2 configured like Workgroup bridge (mobile stations), 20 Switches IE3000 connected to WGB and services connected to SW IE3000.
    Network is working relatively fine, links in our backhaul is OK SNR lower is 21 and max hops on  MAP is 2, we have just one wlan configured, with passive client feature enabled, multicast feature is also enabled, in two times when one MAP is moved to another position (is mining environment) network present instability we have following symptoms:
    Connectivity (through PRTG) with WGB is flapping so services behind were affected.
    We understand if moved a MAP into Mesh probably network convergence, but when network is stable the symptom are maintained, the most strange is from the network we don’t have connectivity to 1300 however connectivity to Switch is OK, in fact we can connect to SWITCH and from it we can connect to 1300 when we are inside Bridge everything interfaces are up including radios, logs show some deauthenticate, but we have configuration without authentication just for now. In WCS we have a alarm CPU Receive Multicast Queue is full on Controller in the time that issue is arise. We make to following actions:
    Enable Multicast, previously the final customer disable this feature.
    Vlans  were pruned to the WLC to only what it needs
    Disable passive client (two weeks ago was enabled), in this point the services is more stable WGB is response from network and services is no affected, so we understand with the passive client is enabled the proxy ARP feature is disabled, so we make to captures in Switch IE300 for another issue one week ago,  and we saw too many ARP broadcast from Gateway to all WGB and clients connected to WGB, so our doubts is this symptom is in relation with the message on WCS, version on 1300.
    Any comment or action is welcome.
    Thanks a lot!

    What kind of clients are behind the IE3000's? Are they passive?
    The proper way to work with the passive clients is putting their MAC address in the Mac Filtering in the WLC and enabling the "passive client" in the WLAN.
    Then you enable L2 bridge forwarding on the 1300 with the "bridge 1 addressxxxx.xxxx.xxxx forward FastEthernet0" command.
    Then you add a static arp entry in the L3 switch that the SVI resides on.
    When you don't have connectivity to 1300. Keep a ping going to it and then try to ping it from your IE3000. If it starts pinging from you computer immediately after that - it sounds like you have an ARP issue.
    Is it possible to post the configs of the IE3000's and 1300's?

  • 1131AG(ROOT AP) to 1131AG(WGB) Multicast Issue

    I have two 1131AG with one configured as a Root AP and another as a WGB. Everything is working great except passing multicast traffic between the two.
    Any one know why?
    Thanks,
    Steve

    The Reliable multicast messages from the access point to workgroup bridges setting limits reliable delivery of multicast messages to approximately 20 Cisco Aironet Workgroup Bridges that are associated to the wireless device. The default setting, disabled, reduces the reliability of multicast delivery to allow more workgroup bridges to associate to the wireless device. Access points and bridges normally treat workgroup bridges not as client devices but as infrastructure devices, like access points or bridges. Treating a workgroup bridge as an infrastructure device means that the wireless device reliably delivers multicast packets, including Address Resolution Protocol (ARP) packets, to the workgroup bridge. For more information on this read http://www.cisco.com/en/US/docs/wireless/access_point/12.4_3g_JA/configuration/guide/s43rf.html#wp1085924

  • WLC 5508 8.0.100 AP dropout anf fallback issue

    After WLC upgrade to 8.0.100 [ not in HA mode], the AP seem to be dropping out and reconnect using the fallback to IP-  inspite of the statically configured IP on the AP
    Running Outdoor mesh AIR-CAP1552E-N-K9 on WLC 5508
    (Cisco Controller) >show boot
    Primary Boot Image............................... 8.0.100.0 (default) (active)
    Backup Boot Image................................ 7.6.101.2
    =========
    Last AP disconnect details
    - Reason for last AP connection failure.................... The AP has been reset by the controller
    - Last AP disconnect reason................................ Unknown failure reason
    Last join error summary
    - Type of error that occurred last......................... Lwapp join request rejected
    - Reason for error that occurred last...................... No Mwar payload found in join request
    - Time at which the last join error occurred............... Dec 03 00:05:26.114
    AP disconnect details
    - Reason for last AP connection failure.................... The AP has been reset by the controller

    We downgraded the WLC to  7.4.121.0 and finally got rid of the DHCP problem
    But encountered a new issue
    The WGB once connected to the mesh AP does not reconnect to the network  , auth failure-   AIR-SAP1602E-Z-K9 running  - ap1g2-k9w7-mx.152-2.JB2
    Local EAP auth configured for WGB client on the WLC
    Looks more like the WGB stuck in a state , unable to negotiate its credentials
    Controller log
    *dot1xMsgTask: Mar 24 10:33:52.737: #DOT1X-3-WPA_SEND_STATE_ERR: 1x_kxsm.c:1404 Unable to send EAPOL-key msg  - invalid WPA state (0) - client f4:0f:1b:23:03:37
    Attached is the debug and client status from WLC
    Any  idea what is going on
    Thanks

  • WLC 5508 - WGBs & HREAP on LAN

    So, I really have two questions here.  For some background information, I have a wireless network with two WLC 5508 controllers and 220 LWAPs in the same location as the controllers.  All APs are currently in local mode.  I run a few guest networks as well as some other client networks.  One client in particular uses their network to connect mobile machines to their VLAN.  The only issue is that the machines do not have wireless adapters.  Instead, the manufacturer put inside the chassis, a D-Link WGB, which has an ethernet cable, you then have to plug into the ethernet port.  These devices cannot seem to connect to the network.  I have found, the WGBs do associate on the network, but the wired client behind it cannot pass traffic onto the VLAN.  I have also tried connecting PCs with different SOHO style WGBs from different manufacturers with the same result.
    After going through Cisco's documentation, I found that using 1230s in WGB mode can resolve this issue since they use IAPP to communicate the MAC table of the wired side clients they service back to the controller.  I have configured a 1230, and used it as the WGB for the client machine instead of the D-Link and it does seem to work, but this would mean configuring a considerable number of 1230s to hand over to the client.
    The first question would be, Is there something I am missing that I would need to do in order to allow SOHO style WGBs to forward wired side client traffic onto the network while LWAPs are in local mode? Or would the WGB NEED to support IAPP?
    The second question is that, I may have found another solution to this already, but would like some input prior to committing.
    This client also uses these same machines with the same WGBs inside the chassis at another location where the client operates the network themselves.  They also use the same WLC model with the same version, and same APs.  The only difference is that they use H-REAP mode with local switching.
    I also tested this idea, and it seemed to work.  With the AP in H-REAP mode, and the client's WLAN set to local switching, the machine and WGB connected with no problem.
    So the question with this, would be; would there be any disadvantages in running all 220 APs at this location in H-REAP mode?  What would I be losing if anything?  Also, I would like to keep all other WLANs centrally switched.
    I understand what the difference would be for this client's WLAN if I ran in H-REAP mode with local switching, but what would the difference be in the other guest WLANs if I set them to be centrally switched?  (Is there any difference between running APs in local mode vs running APs in H-REAP with central switching?)

    Hey,
    I read your quesiton quickly so I might miss some points, but I think you need to do some more configuraiton for your passive clients behind the WGB:
    '''snip'''
    Passive Clients Behind a WGB
    The controller might not be able to see passive clients behind a WGB. Clients (such as cameras and programmable logic devices) do not initiate a traffic stream unless they are connected. Complete these steps in order avoid this issue:
    Add a static MAC filter entry for the passive WGB device and MAC filter entry for the devices that are behind it.
    Use this command in order to enable MAC filtering on the WLAN along with aaa override:config macfilter ipaddress MAC_address IP_address
    Add a static entry on the WGB IOS-based device: bridge 1 addressxxxx.xxxx.xxxx forward FastEthernet0Note: In addition, increase the dot11 activity timer.
    Add a static ARP entry on the L3 router:
    hostname(config)#arp
          arpa
    '''snip'''
    Reference: http://tiny.cc/cjsxu
    Also, know please that WGB is not supported with hybrid REAP (H-REAP).
    Even if it worked with you sometimes, it is not supported and cisco did not design it to work with HREAP.
    http://bit.ly/yLn9D1
    I am only aware about one difference between central switching HREAP and local mode; which is that any limitation applied to HREAP will be applied if it is central switching. just like our situation with WGB with HREAP.

  • Wierd DHCP Issue

    Hello All,
    I facing a very wierd  DHCP issue and would like to know your thoughts on it.
    I have my wired clients on vlan 1 and wireless cleints(eap-peap) on VLAN 2.
    We are facing an issue where multiple wired clients who were on access port vlan 1 are receiving IP address from wireless subnet(vlan2) -their DHCP server was the WLC virtual gateway IP address(1.1.1.1). This is causing an outage to few wired clients.
    The WLC trunk does not have vlan 1 allowed on its ports and all APs are in local mode and all on access vlan.
    I'm not entirely sure whats causing this, but only way I think this is possible is  that 'A Client' laptop has his network connections  bridged - his wired nic on VLAN 1 and wireless NIC on vlan 2, acting like a WGB, which is causing new wired clients(vlan1) DHCP broadcast request forwared through the bidge mode laptop to AP--> WLC. Do you think this is possible??
    Havent been able to identify which client is causing this issue yet.
    Has anyone faced a similar issue and anyway to block this through WLC/ACS policy?
    Thanks
    Jino

    Hi,
    Might we consider to make use of network monitor to take a look at the traffics for the 1.1.1.1 address?
    How to use Network Monitor to capture network traffic
    Download link here:
    Microsoft Network Monitor 3.4
    Best regards
    Michael Shao
    TechNet Community Support

  • WGB with AP1310 and LAP with WLC in 4.1

    I make a WGB with a autonomous AP1310 and an LAP manage by a WLC2006 in 4.1 version.
    The bridge is up and working, but it's very strange:
    - The bridge is up and i can always ping the IP of the BRI interface of the 1310.
    - When the bridge go up, i see the IP of computer behind the 1310 in a Wireless client list of the controler, but i can ping it only 25% of time.
    - If i wait a long time, the MAC/IP are leaving the Wireless client list of the controler and i can ping the computeur. At this time, if i do a "debug arp enable" on the controler i didn't see ARP response from the controler for computeur bihind the bridge.
    Does anyone have the same problem ? Does anyone do WBG with controler in 4.1 ? Any issues ?
    Thanx for your help.

    Hello,
    Thanks for your prompt replies.
    @Saritha:
    1. On new document Save call is giving message as "NOT Modified", as i didn't perform any actions.So Yes, I'm able to perform SAVE.
    2. Yes, I have performed other operations like creating a Report.
    @Eric: 3. Yes, the folder which I'm trying to save is writable for the user.
    My Observation: When I'm trying to 'SAVE AS' on new document its giving 500 error as I said earlier.
    1. But, after creating new document, I created a new Report for that document, then 'SAVE AS' working. That means after performing some action/modifying the document 'SAVE AS'  is working for me.
    2. Same issue(500 error) observed when trying to perform 'SAVE AS' call on the EXISTING document as well (which is create in BI Launchpad, refreshing and working fine).
    So, is it mandatory to perform any action (which brings the document to Modify mode [i guess]) before this 'SAVE AS' call ?
    Thanks,
    Ram

  • WGB association/re-association timing

    Hi Guys,
    Just want to ask a question:  what is the acceptable association or reassociation time for the WGB?
    Our environment is on a shipyard, and AP's are mounted on a light mast around 30 meters high, and our WGB clients are mounted on the cranes, these cranes are moving around the area.  The cranes are around 15 meters high.  We are implementing Cisco LEAP.   I have noticed that the association or re-association timing of some of our WGB clients are taking around 50 seconds and some are more than 60 seconds before it was able to re-associate to another AP.
    So in this case, is this a normal condition?

    Hi Kaye,
    This issue is only happening to some but not all WGB Clients.  We did some site survey just using the netstumbler on the crane level and was able to see some rogue AP's, however their signal strength is not that strong at around -90 to -100 dbm.  Could this rogue AP's caused this issue to happen?  What are other external factors that may contribute to this interference?
    Thanks!

  • New DVR Issues (First Run, Channel Switching, etc.)

    I've spent the last 30 minutes trying to find answers through the search with no luck, so sorry if I missed something.
    I recently switched to FIOS from RCN cable in New York.  I've gone through trying to setup my DVR and am running into issues and was hoping for some answers.
    1.  I setup two programs to record at 8PM, I was watching another channel at the time and only half paying attention.  Around 8:02 I noticed a message had popped up asking if I would like to switch channels to start recording.  I was expecting it to force it to switch like my old DVR, but in this case it didn't switch and I missed the first two minutes of one of the shows.  I typically leave my DVR on all day and just turn off the TV, this dual show handling will cause issues with that if I forget to turn off the DVR.  Is there a setting I can change that will force the DVR to choose one of the recording channels?
    2.  I setup all my recordings for "First Run" because I only want to see the new episodes.  One show I setup was The Daily Show on comedy central, which is shown weeknights at 11pm and repeated 3-4 times throughout the day.  My scheduled recordings is showing all these as planned recordings even though only the 11pm show is really "new".  Most of the shows I've setup are once a week so they aren't a problem, but this seems like it will quickly fill my DVR.  Any fixes?
    Thanks for the help.
    Solved!
    Go to Solution.

    I came from RCN about a year ago.  Fios is different in several ways, not all of them desirable.  Here are several ways to get--and fix--unwanted recordings from a series recording setup.
    Some general principles. 
    Saving changes.  When you originally create a series with options, or if you go back to edit the options for an existing series, You MUST save the Series Options changes.  Pretty much everywhere else in the user interface, when you change an option, the change takes effect immediately--but not in Series Options.  Look at the Series Options window.  Look at the far right side.  There is a vertical "Save" bar, which you must navigate to and click OK on to actually save your changes.  Exiting the Series Options window without having first saved your changes loses all your attempted changes--immediately.
    Default Series Options.  This is accessed  from [Menu]--DVR--Settings--Default Series Options.  This will bring up the series options that will automatically be applied to the creation of a NEW series. The options for every previously created series will not be affected by a subsequent modification of the Default Series Options.  You should set these options to the way you would like them to be for the majority of series recordings that you are likely to create.  Be sure to SAVE your changes.  This is what you will get when you select "Create Series Recording" from the Guide.  When creating a new series recording where you think that you may want options different from the default, select "Create Series with Options" instead.  Series Options can always be changed for any individual series set up later--but not for all series at once.
    Non-series recordings.  With Fios you have no directly available options for these.  With RCN and most other DVRs, you can change the start and end times for individual episodes, including individual episodes that are also in a series.  With Fios, your workarounds are to create a series with options for a single program, then delete the series later;  change the series options if the program is already in a series, then undo the changes you made to the series options later; or schedule recordings of the preceding and/or following shows as needed.
    And now, to the unwanted repeats. 
    First, make sure your series options for the specific series in question--and not just the series default options--include "First Run Only".  If not, fix that and SAVE.  Then check you results by viewing the current options using the Series Manager app under the DVR menu.
    Second, and most annoying, the Guide can have repeat programs on your channel tagged as "New".  It happens.  Set the series option "Air Time" to "Selected Time".  To make this work correctly, you must have set up the original series recording after selecting the program in the Guide at the exact time of a first run showing (11pm, in your case), and not on a repeat entry in the Guide.  Then, even it The Daily Show is tagged as New for repeat showings, these will be ignored. 
    Third, another channel may air reruns of the program in your series recording, and the first showing of a rerun episode on the other channel may be tagged as "New".  These can be ignored in your series if you set the series option "Channel" to "Selected Channel".  Related to this, if there is both an SD and HD channel broadcasting you series program, you will record them both if the series option "Duplicates" is set to "Yes".  However, when the Channel option is set to "Selected Channel", the Duplicates Option is always effectively "No", regardless of what shows up on the options screen.  
    As for you missing two minutes,  I have sereral instances in which two programs start recording at the same time.  To the best of my recollection, whenever the warning message has appeared, ignoring it has not caused a loss of recording time.  You might have an older software version.  Newest is v.1.8.  Look at Menu--Settings--System Info.  Or, I might not have noticed the loss of minutes.  I regularly see up to a minute of previous programming at the start of a recording, or a few missing seconds at the beginning or end of a recording.  There are a lot of possibilities for that, but the DVR clock being incorrect is not one of them.  With RCN, the DVR clocks occasionally drifted off by as much as a minute and a half.

  • Pension issue Mid Month Leaving

    Dear All,
    As per rule sustem should deduct mid month joining/leaving/absences or transfer scenarios, the Pension/PF Basis will be correspondingly prorated. But our system is not doing this. In RT table i have found 3FC Pension Basis for Er c 01/2010                    0.00           6,500.00.
    Employee leaving date is 14.04.2010. system is picking pension amout as 541. Last year it was coming right.
    Please suggest.
    Ashwani

    Dear Jayanti,
    We required prorata basis pension in case of left employees and system is not doing this. This is the issue. As per our PF experts Pension amount should come on prorata basis for left employees in case they left mid of month.System is doing prorata basis last year but from this year it is deducting 541. I am giving two RT cases of different years.
    RT table for year 2010. DOL 26.04.2010
    /111 EPF Basis              01/2010                    0.00           8,750.00 
    /139 VPF Basis              01/2010                    0.00           8,750.00 
    /3F1 Ee PF contribution     01/2010                    0.00           1,050.00 
    /3F3 Er PF contribution     01/2010                    0.00             509.00 
    /3F5 Ee Mon PF contribution 01/2010                    0.00           1,050.00 
    /3F6 Ee Ann PF contribution 01/2010                    0.00          12,600.00 
    /3F9 PF adm chrgs * 1,00,00 01/2010                    0.00              96.25 
    /3FA PF basis for Ee contri 01/2010                    0.00           8,750.00 
    /3FB PF Basis for Er Contri 01/2010                    0.00           8,750.00 
    /3FJ VPF basis for Ee contr 01/2010                    0.00           8,750.00 
    /3FL PF Basis for Er Contri 01/2010                    0.00           6,500.00 
    /3F4 Er Pension contributio 01/2010                    0.00             541.00
    /3FC Pension Basis for Er c 01/2010                    0.00           6,500.00
    /3FB PF Basis for Er Contri 01/2010                    0.00           8,750.00
    /3FC Pension Basis for Er c 01/2010                    0.00           6,500.00
    /3FJ VPF basis for Ee contr 01/2010                    0.00           8,750.00
    /3FL PF Basis for Er Contri 01/2010                    0.00           6,500.00
    /3R3 Metro HRA Basis Amount 01/2010                    0.00           8,750.00
    1BAS Basic Salary           01/2010                    0.00           8,750.00
    RT table for year 2009. DOL 27.10.2009
                                                                                    /111 EPF Basis              07/2009                    0.00           9,016.13
    /139 VPF Basis              07/2009                    0.00           9,016.13
    /3F1 Ee PF contribution     07/2009                    0.00           1,082.00
    /3F3 Er PF contribution     07/2009                    0.00             628.00
    /3F5 Ee Mon PF contribution 07/2009                    0.00           1,082.00
    /3F6 Ee Ann PF contribution 07/2009                    0.00           8,822.00
    /3F9 PF adm chrgs * 1,00,00 07/2009                    0.00              99.18
    /3FA PF basis for Ee contri 07/2009                    0.00           9,016.00
    /3FB PF Basis for Er Contri 07/2009                    0.00           9,016.00
    /3FJ VPF basis for Ee contr 07/2009                    0.00           9,016.00
    /3FL PF Basis for Er Contri 07/2009                    0.00           5,452.00
    /3FB PF Basis for Er Contri 07/2009                    0.00           9,016.00 
    /3FC Pension Basis for Er c 07/2009                    0.00           5,452.00 
    /3FJ VPF basis for Ee contr 07/2009                    0.00           9,016.00 
    /3FL PF Basis for Er Contri 07/2009                    0.00           5,452.00 
    /3R4 Non-metro HRA Basis Am 07/2009                    0.00           9,016.13 
    1BAS Basic Salary           07/2009                    0.00           9,016.13 
    Now please suggest what to do. where is the problem  ? If have also checked EXIT_HINCALC0_002 but nothing written in it.
    With Regards
    Ashwani

  • Open PO Analysis - BW report issue

    Hello Friends
    I constructed a query in BW in order to show Open Purchase Orders. We have custom DSO populated with standard
    datasource 2lis_02_itm (Purcahse Order Item). In this DSO we mapped the field ELIKZ to the infoobject 0COMP_DEL
    (Delivery completed).
    We loaded the data from ECC system for all POs and found the following issue for Stock Transport Purchase orders (DocType = UB).
    We have a PO with 4 line items. For line items 10 and 20, Goods issued, Goods received and both the flags "Delivery
    complete" and "Final delivery" checked. For line items 30 and 40, only delivery indicator note is issued for zero
    quantity and Delivery complete flag is checked (Final delivery flag is not checked) in ECC system. For this PO, the
    delivery completion indicator is not properly updated in the DSO for line items 30 and 40. The data looks like the
    following:
    DOC_NUM     DOC_ITEM       DOCTYPE     COMP_DEL
    650000001       10     UB        X
    650000001       20     UB        X
    650000001       30     UB
    650000001       40     UB      
    When we run the Open PO analysis report on BW side this PO is appearing in the report but the same is closed in ECC
    system.
    Any help is appreciated in this regard.
    Thanks and Regards
    sampath

    Hi Priya and Reddy
       Thanks for your response.
                         Yes the indicator is checked in EKPO table for items 30 and 40 and delta is running regularly for more than 1 year and no issues with other POs. This is happening only for few POs of type Stock Transport (UB).
                        I already checked the changes in ME23N and the Delivery completed indicator was changed and it reflected in EKPO table. Further, i checked the PSA records for this PO and i am getting the records with the Delivery completed flag but when i update from PSA to DSO the delivery completed indicator is not updating properly.
                       In PSA, for item 30 i have the following entries. Record number 42 is capturing the value X for ELIKZ but after that i am getting two more records 43 and 44 with process key 10 and without X for ELIKZ. I think this is causing the problem.
    Record No.    Doc.No.                    Item              Processkey         Rocancel     Elikz
        41               6500000001            30                    11                            X           ---    
        42               6500000001            30                    11                            ---           X
        43               6500000001            30                    10                            X           ---
        44               6500000001            30                    10                            ---         ---
    (Here --- means blank)        
    Thanks and Regards
    sampath

  • HP LaserJet Enterprise 600 M602 driver issue

    Hello,
    I've got issue with 600-series printers. We use the latest UPD drivrer ver. 61.175.1.18849 and print from XenApp 6.5. The error occurs every time when users try to print jpg files from XenApp session. It only happens with 600 series printers and UPD.
    Also I've tried to assign native 600-series driver ver. 6.3.9600.16384 and it works good. But with that driver system says that it's color printer and it brokes our printing reports. These reports are very important for us. So we can't use printer and that driver as well.
    Printer installed on Windows Server 2012 R2. All clients are Windows 7 x64. XenApp Servers are Server 2008R2.
    Is it possible to get fixed UPD driver or correct native driver for Server 2012 R2?
    Regards,
    Anatoly

    I am sorry, but to get your issue more exposure I would suggest posting it in the commercial forums since this is a commercial printer. You can do this at Printers - LaserJet.
    Click on New Post.
    I hope this helps.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • Windows 7 displays error message when exiting +cursor issue

    Two issues here. CS5 Phoshop on Wind 7 64 bit.
    Physical processor count: 8
    Processor speed: 3073 MHz
    Built-in memory: 12279 MB
    Free memory: 9577 MB
    Memory available to Photoshop: 10934 MB
    Memory used by Photoshop: 80 %
    Image tile size: 128K
    First issue is since the latest automatic Adobe update (why fix what isn't broken?) Every time I now exit Photoshop I get the message "Adobe QT Server has stoped working" and occasionally it happens when I exit bridge. Indesign is also behaving badly. I can no longer start a previous document from file manager without ID crashing out.
    The other is the cursors in Clone and erase lose their edge (become invisable) for no reason - well not quite. Noise Ninja crashed Photoshop when I tried to use it. I reinstalled it and all is well. The cursor issue seems to be intermittant but came back (for no reason) after I reinstalled NN. I can't seem to change the cursor, no matter what I do. The problem is now seriously affecting how I work. Almost enough to go back to Win XP which ran CS5 Photoshop flawlessly.
    Any help will be gratefully accepted.
    Doug

    function(){return A.apply(null,[this].concat($A(arguments)))}
    doug87510 wrote:
    The recent problem is the entire outline of the cursor (including the crosshair in the middle) was missing at any size of cursor. All I had was exactly what I'd get if I used a real spraygun.
    Well, that issue is simply a matter of hitting the Caps Lock key.  When Caps Lock is on, you'll see the cursor outline, and when it is off you'll see a crosshair.  That's a feature, not a bug.
    Glad to hear the 11.1 drivers are out.  I will download them and try them now myself.
    Regarding "Adobe QT" crashing...  QT brings to mind QuickTime, though that is Apple, not Adobe.  Do you have Apple QuickTime installed?
    Regarding memory usage, with 12 GB of installed RAM, you should be able to set Photoshop to use 90% or more in Edit - Preferences - Performance.
    -Noel

  • Issue in Creation of Periodicals for Contracts in CRM7.0

    Hello,
    I have a requirement to create Contracts in CRM7.0 system.
    And I am doing this using the BAPI *BAPI_BUSPROCESSND_CREATEMULTI*
    Good part is Contract Order gets created, but onlywith Header Details.
    The issues i am facing --
    1. I need to know what kind/type of data must be passed to the interface parameters, the F1 Help/Documentation is vague.
    2. I am passing data in the INPUT FIELDS structure with the Object ID, Handle Number, Reference GUID and Fieldname,
        here what does 'Logical Key' field indicate? What should be passed here.
        What does 'REFERENCE KIND' field indicate, i have been passng 'A' for everything (to be frank i dont know whats its significance is!!).
    3. With so much, My Order gets created but with less than half details, i.e. the Objects not getting created are -  Partner, Product, terms/appointments, Status, LongTexts......
    Any help/inputs would be appreciated.
    Hope my problem is stated clearly ...
    --Regards
    Dedeepya

    Hi Anu,
    i found my solution by debugging with existing data or while creating it in CRMD_ORDER.
    Ensure that you are passing a correct entry in INPUT_FIELDS structure.
    As i haven't worked on rebates i woudlnt be able to help you, I suggest you debug to arrive at a solution.
    You can preset your break-points at :-
    1. FM - CRM_ORDER_MAINTAIN
    2. CRM_ORDER_MAINTAIN_MULTI_OW -- Debug through the complete FM.
    3. CRM_ORDER_PREPARE_MULTI_OW -- The data is set in this function module.
    Regards
    Dedeepya C

  • Issue in creation of plant related data at receiving server using BD10

    Hi all,
    This is regarding Material master creation using B10.I am using MATMAS05 message type for sending data from one system to another.Data is sent and received successfully.When i go in mm03 i can see all the views created successfully accept views related to PLANT.Please guide to resolve the issue.
    When i entered into Log-
    1)"The field MBEW-BKLAS is defined as a required field; it does not contain an entry".
    2)"No material master data exists for material AB_08.04.09(30) in plant 4001".
    My segemnt is as follows-
    ZMATMAS05                      matmas05
           E1MARAM                        Master material general data (MARA)
               Z1KLART                        KLART----
    My extention
               E1MARA1                        Additional Fields for E1MARAM
               E1MAKTM                        Master material short texts (MAKT)
               E1MARCM                        Master material C segment (MARC)
                   Z1AUSPM                        E1AUSPMDistribution of Classification:----
    My extention
                   E1MARC1                        Additional Fields for E1MARCM
                   E1MARDM                        Master material warehouse/batch segment (MARD)
                   E1MFHMM                        Master material production resource/tool (MFHM)
                   E1MPGDM                        Master material product group
                   E1MPOPM                        Master material forecast parameter
                   E1MPRWM                        Master material forecast value
                   E1MVEGM                        Master material total consumption
                   E1MVEUM                        Master material unplanned consumption
                   E1MKALM                        Master material production version
               E1MARMM                        Master material units of measure (MARM)
               E1MBEWM                        Master material material valuation (MBEW)
               E1MLGNM                        Master material material data per warehouse number (MLGN)
               E1MVKEM                        Master material sales data (MVKE)
               E1MLANM                        Master material tax classification (MLAN)
               E1MTXHM                        Master material long text header
               E1CUCFG                        CU: Configuration data
           E1UPSLINK                      Reference from Object to Superior UPS
    Thanks.
    Edited by: sanu debu on Apr 27, 2009 7:10 PM

    CREATE CONTROLFILE SET DATABASE "NEWDB" NORESETLOGS ARCHIVELOGAlso when you are setting a new database, the option should be RESETLOGS and not NORESETLOGS.
    'D:\APP\ADMINISTRATOR\ORADATA\NEWDB\ONLINELOG\O1_MF_2_7FK0XKB8_.LOG
    D:\APP\ADMINISTRATOR\ORADATA\NEWDB\DATAFILE\O1_MF_SYSTEM_7FK0SKN0_.DBFWhy underscore(_) at the end of the datafile name. Any specific reason ?

Maybe you are looking for