What are normal readings

I have been using the CoreDuoTemp app to gauge CPU activity and temperature i have the MBP 2.0 and right now i have typed a yes command into terminal and i get a reading of 70degrees celsius and 100% cpu usage but my "current" value only shows 1000MHZshouldn't that be 2000 given that it is a 2.0, on my previous MBP the 1.83 it would give a current of 1833, when it was maxed
Need some help, this is the 4th MBP from apple, because the first 3 had serious defects that made the computer unusable.
and even after i did all the updates to this one as soon as i got it, i am still getting the super HOT area above the F keys

It sounds like every thing is pretty much "normal" with your MBP. have you read this part for the MBP spcifications page?
"MacBook Pro continuously monitors system thermal and power conditions, and may adjust processor speed as needed to maintain optimal system operation."
Regards,

Similar Messages

What are normal business hours for support?

What are normal business hours for Apple Support in the Hong Kong region?
The support page at:
http://www.apple.com/hk/en/support/iphone/contact/
and the phone number, when called, do not specify normal business hours. In fact, the phone number, when called, only says "call back during normal business hours".
Please... are they open on Sunday, Saturday, 8pm, 7pm, ????????

Really kb1951, I did try calling on Saturday, about 6pm. They were closed. But that does not answer my question. And "normal" support lines do address their hours in the recording.
Additionally, if you call at 4pm, even, how does that tell you when they open??? Should I call at 7am, 8am, 9am, 10am, just to get my answer?
You trying to answer my question based on what other businesses do is really a waste of your and my time. As you're just "guessing". I can guess. I don't need you for that!
I came to the support community for a reason - to get an answer, not a guess.

Powermac G5: What are normal temperatures?

I recently started paying attention to the temp readouts using a temp monitor. Now im not sure what the normal temps are for my processors, but 180.00F seemed really high. I am running dual 2.7's.
Can anyone tell me what the normal range of temperatures are for a G5 with similar specs? Im not sure if i should be concearned or not..
G5 Power Mac
Dual 2.7g
4g Ram
6800 Ultra
2x 400gb HDD
Thanks so much for any assistance.

Hello all,
I'm using a G5 2,5GHz DP and I recognized also that the CPU temperature was quite high. Also I found the noise of the fans quite annoying. They were spinning up i.e. when opening FileMaker databases over a network or when I was starting an iChat video conference and so on.
Then I found out the following procedure to reduce the temperature of the CPUs and also the noise of the fans:
First download CHUD from the Apple Developer pages and install it.
http://developer.apple.com/tools/download/
After successful installation you'll find a preference pane called "Processor" in the "System Preferences". Open this Preference Panel and activate the option "Allow NAP".
Then please open the Preference Panel "Energy Saver" and there click onto "Options" at the top of the window. Then you'll see a preference for the CPU performance which you should set to "Minimal".
I know that this will cost performance, but if I do really need best CPU performance I can set it to "Maximum". All the time when I just use my G5 for normal office work, it is much more quiet than before. Of course this is not a solution for server or XGrid environments, but it is perfect for offices.
The average CPU temperature of the upper CPU (A) has been reduced from 75° C to around 60° C. The average temperature of the lower CPU (B) went down from around 65° C to 50° C.
Hope this helps.
Juergen

What are normal operating temperatures of the i7-2620 in the X220, using TPFanControl?

So I finally got TPFanControl working on my X220 after I really started noticing the fan spinning up and producing high-pitched whine. The fan had begun to remain on all the time, even while on battery with the CPU sitting at 800MHz. I could have sworn the fan remained off a lot of the time beforehand.
So, what are the normal operating temps of the i7-2620CPU? Right now plugged in at "Balanced" speed, jumping between 2.7GHz and 800MHz and with the fan manually set to "7," 4500rpm, in TPFanControl, it shows the temperature at 63C. On battery at 800MHz, the temp goes between 50C and 60C.
CPU Utilization remains at 7% when on batteries, 0-4% while plugged in at idle.
Are those normal numbers? If not, do I have some kind of problem with the thermal paste or heatsink, or dust?

at idle? no my fan is hardly audible at idle.
what you are describing sounds like a problem with the either fan, or improper installation, in which cases you would need warranty.
If you boot the laptop into the bios menu, does the fan come on?
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

Early 2009, 24" iMac: What are normal operating temps?

My iMac overheats and automatically shuts down frequently. Sometimes, just watching a movie on Quicktime causes the CPU to top 80C and cause a shutdown. Fans never run faster than 3500-3600rpm.
Another thing that I noticed, is that the hiutil process runs twice a day using 100% of my processor, and always causes an overheat and shurtdown.
Can anyone direct me to normal operating temps for this model iMac, or advise what may be worng?
This sreenshot displays temps (Celcius) with only Safari running. With uTorrent running (not actually feeding peers), and Quicktime, I get an overheat.
TEMPS                                   FANS
HD Macintosh   54                Optical drive   801rpm
CPU                    55               Hard Drive      1599rpm
CPU Heatsink   51               CPU Fan          3580rpm
Ambient              39
CPU Diode        72
CPU Heatsink   60
HD Bay               54
Mem Controller 57
Processor 2.93 GHz Intel Core 2 Duo
Memory 4 GB 1067 MHz DDR3
Graphics NVIDIA GeForce GT 120 256 MB
Running Mountain Lion 10.8.

Your temps are somewhat high, but still within acceptable levels.
I would be more comfortable seeing many of the temps in the 40 degree Celsius range.
Your CPU temps are on the high side and probably why your CPU fans are running high.
When was the last time you clear out any of the dust, lint and fine dirt particles from your iMac.
IF you've never done this, you need to completely unplug your iMac, find a heavy blanket or towel to lay your iMac, face down on the soft material. Using a special electronics vacuum, a portable, plug in vacuum or standardnhiuse vacuum with hose and attchments, using either the bare hose end or crvice tool, carefully and slowly vacuum all air intake and exhaust vents, openings and all of the ports to get rid of as much fine dust, dirt and lint as possible.
Do not use a vacuum attachment with brushes. This could cause a problem with random static charges.
Once this is done, re-setup your iMac, plug all your peripherals in and then do an SMC reset by plugging in your iMac to power. Wait 5 seconds, then power up your iMac.
Then report back here with any changes in temps.

What are Normal Disk Speeds

I think that my hard drive is very slow. That's how it seems. This is what hdparm shows:
[kirk@localhost ~]$ sudo hdparm -Tt /dev/sdb3
/dev/sdb3:
Timing cached reads: 1660 MB in 2.00 seconds = 829.94 MB/sec
Timing buffered disk reads: 236 MB in 3.03 seconds = 77.94 MB/sec
[kirk@localhost ~]$ sudo hdparm -Tt /dev/sdb3
/dev/sdb3:
Timing cached reads: 1662 MB in 2.00 seconds = 831.09 MB/sec
Timing buffered disk reads: 226 MB in 3.02 seconds = 74.80 MB/sec
[kirk@localhost ~]$ sudo hdparm -Tt /dev/sdb3
/dev/sdb3:
Timing cached reads: 1718 MB in 2.00 seconds = 858.59 MB/sec
Timing buffered disk reads: 234 MB in 3.00 seconds = 77.90 MB/sec
[kirk@localhost ~]$ df -h
Filesystem Size Used Avail Use% Mounted on
/dev/sdb3 23G 9.3G 13G 43% /
none 1013M 196K 1013M 1% /dev
none 1013M 0 1013M 0% /dev/shm
/dev/sdb1 183M 12M 162M 7% /boot
/dev/sdb5 92G 23G 65G 26% /srv
/dev/sdb6 175G 93G 74G 56% /home
/dev/sdg1 1.9G 213M 1.7G 12% /media/disk
[kirk@localhost ~]$ sudo hdparm -Tt /dev/sdb6
/dev/sdb6:
Timing cached reads: 1614 MB in 2.00 seconds = 806.60 MB/sec
Timing buffered disk reads: 218 MB in 3.02 seconds = 72.22 MB/sec
[kirk@localhost ~]$ sudo hdparm -Tt /dev/sdb5
/dev/sdb5:
Timing cached reads: 1544 MB in 2.00 seconds = 772.22 MB/sec
Timing buffered disk reads: 236 MB in 3.02 seconds = 78.20 MB/sec
Are these times slow?

Wait, there's more
But nothing LOOKS funny to me either here. But I tell you, opening a file in OpenOffice or sometimes just typing a URL into Firefox takes 10 times what I think it should. It was faster before, too. Not sure what/when it changed.
Dec 9 16:45:25 localhost kernel: usb 1-3.1: USB disconnect, address 19
Dec 9 16:45:26 localhost kernel: usb 1-3: new high speed USB device using ehci_hcd and address 20
Dec 9 16:45:26 localhost kernel: usb 1-3: configuration #1 chosen from 1 choice
Dec 9 16:45:26 localhost kernel: hub 1-3:1.0: USB hub found
Dec 9 16:45:26 localhost kernel: hub 1-3:1.0: 4 ports detected
Dec 9 16:45:26 localhost kernel: usb 1-3.1: new high speed USB device using ehci_hcd and address 21
Dec 9 16:45:26 localhost kernel: usb 1-3.1: configuration #1 chosen from 1 choice
Dec 9 16:45:26 localhost kernel: scsi14 : SCSI emulation for USB Mass Storage devices
Dec 9 16:45:26 localhost kernel: usb-storage: device found at 21
Dec 9 16:45:26 localhost kernel: usb-storage: waiting for device to settle before scanning
Dec 9 16:45:31 localhost kernel: hub 1-3:1.0: cannot reset port 1 (err = -71)
Dec 9 16:45:31 localhost kernel: hub 1-3:1.0: cannot reset port 1 (err = -71)
Dec 9 16:45:31 localhost kernel: hub 1-3:1.0: cannot reset port 1 (err = -71)
Dec 9 16:45:31 localhost kernel: hub 1-3:1.0: cannot reset port 1 (err = -71)
Dec 9 16:45:31 localhost kernel: hub 1-3:1.0: cannot reset port 1 (err = -71)
Dec 9 16:45:31 localhost kernel: hub 1-3:1.0: Cannot enable port 1. Maybe the USB cable is bad?
Dec 9 16:45:31 localhost kernel: hub 1-3:1.0: cannot disable port 1 (err = -71)
Dec 9 16:45:31 localhost kernel: hub 1-3:1.0: cannot reset port 1 (err = -71)
Dec 9 16:45:31 localhost kernel: hub 1-3:1.0: cannot reset port 1 (err = -71)
Dec 9 16:45:31 localhost kernel: hub 1-3:1.0: cannot reset port 1 (err = -71)
Dec 9 16:45:31 localhost kernel: hub 1-3:1.0: cannot reset port 1 (err = -71)
Dec 9 16:45:31 localhost kernel: hub 1-3:1.0: cannot reset port 1 (err = -71)
Dec 9 16:45:31 localhost kernel: hub 1-3:1.0: Cannot enable port 1. Maybe the USB cable is bad?
Dec 9 16:45:31 localhost kernel: hub 1-3:1.0: cannot disable port 1 (err = -71)
Dec 9 16:45:31 localhost kernel: hub 1-3:1.0: cannot reset port 1 (err = -71)
Dec 9 16:45:31 localhost kernel: hub 1-3:1.0: cannot reset port 1 (err = -71)
Dec 9 16:45:31 localhost kernel: hub 1-3:1.0: cannot reset port 1 (err = -71)
Dec 9 16:45:31 localhost kernel: hub 1-3:1.0: cannot reset port 1 (err = -71)
Dec 9 16:45:31 localhost kernel: hub 1-3:1.0: cannot reset port 1 (err = -71)
Dec 9 16:45:31 localhost kernel: hub 1-3:1.0: Cannot enable port 1. Maybe the USB cable is bad?
Dec 9 16:45:31 localhost kernel: hub 1-3:1.0: cannot disable port 1 (err = -71)
Dec 9 16:45:31 localhost kernel: hub 1-3:1.0: cannot reset port 1 (err = -71)
Dec 9 16:45:31 localhost kernel: hub 1-3:1.0: cannot reset port 1 (err = -71)
Dec 9 16:45:31 localhost kernel: hub 1-3:1.0: cannot reset port 1 (err = -71)
Dec 9 16:45:31 localhost kernel: hub 1-3:1.0: cannot reset port 1 (err = -71)
Dec 9 16:45:31 localhost kernel: hub 1-3:1.0: cannot reset port 1 (err = -71)
Dec 9 16:45:31 localhost kernel: hub 1-3:1.0: Cannot enable port 1. Maybe the USB cable is bad?
Dec 9 16:45:31 localhost kernel: hub 1-3:1.0: cannot disable port 1 (err = -71)
Dec 9 16:45:31 localhost kernel: hub 1-3:1.0: cannot disable port 1 (err = -71)
Dec 9 16:45:31 localhost kernel: usb-storage: device scan complete
Dec 9 16:45:31 localhost kernel: hub 1-3:1.0: hub_port_status failed (err = -71)
Dec 9 16:48:24 localhost kernel: usb 4-1: new full speed USB device using uhci_hcd and address 2
Dec 9 16:48:24 localhost kernel: usb 4-1: configuration #1 chosen from 1 choice
Dec 9 16:49:34 localhost kernel: usb 1-3.1: USB disconnect, address 21
Dec 9 16:49:34 localhost kernel: usb 1-3: reset high speed USB device using ehci_hcd and address 20
Dec 9 16:49:35 localhost kernel: usb 1-3.1: new high speed USB device using ehci_hcd and address 23
Dec 9 16:49:35 localhost kernel: usb 1-3.1: configuration #1 chosen from 1 choice
Dec 9 16:49:35 localhost kernel: scsi15 : SCSI emulation for USB Mass Storage devices
Dec 9 16:49:35 localhost kernel: usb-storage: device found at 23
Dec 9 16:49:35 localhost kernel: usb-storage: waiting for device to settle before scanning
Dec 9 16:49:40 localhost kernel: scsi 15:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0
Dec 9 16:49:40 localhost kernel: sd 15:0:0:0: Attached scsi generic sg2 type 0
Dec 9 16:49:40 localhost kernel: scsi 15:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0
Dec 9 16:49:40 localhost kernel: sd 15:0:0:1: Attached scsi generic sg3 type 0
Dec 9 16:49:40 localhost kernel: sd 15:0:0:0: [sdc] Attached SCSI removable disk
Dec 9 16:49:40 localhost kernel: scsi 15:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0
Dec 9 16:49:40 localhost kernel: sd 15:0:0:2: Attached scsi generic sg4 type 0
Dec 9 16:49:40 localhost kernel: scsi 15:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0
Dec 9 16:49:40 localhost kernel: sd 15:0:0:3: Attached scsi generic sg5 type 0
Dec 9 16:49:40 localhost kernel: usb-storage: device scan complete
Dec 9 16:49:40 localhost kernel: sd 15:0:0:1: [sdd] Attached SCSI removable disk
Dec 9 16:49:40 localhost kernel: sd 15:0:0:3: [sdf] Attached SCSI removable disk
Dec 9 16:49:40 localhost kernel: sd 15:0:0:2: [sde] Attached SCSI removable disk
Dec 9 17:01:01 localhost dhcpcd: received SIGALRM, rebinding lease
Dec 9 17:01:01 localhost dhcpcd: eth0: reading lease `/var/lib/dhcpcd/dhcpcd-eth0.lease'
Dec 9 17:01:01 localhost dhcpcd: eth0: rebinding lease of 10.0.0.1
Dec 9 17:01:01 localhost dhcpcd: sending signal 14 to pid 1131
Dec 9 17:01:01 localhost dhcpcd: eth0: sending DHCP_REQUEST (xid 0x7b6fcecc), next in 3.53 seconds
Dec 9 17:01:01 localhost dhcpcd: eth0: acknowledged 10.0.0.1 from 10.0.0.138
Dec 9 17:01:01 localhost dhcpcd: eth0: leased 10.0.0.1 for 86400 seconds
Dec 9 17:01:01 localhost dhcpcd: eth0: adding IP address 10.0.0.1/24
Dec 9 17:01:01 localhost dhcpcd: eth0: writing lease `/var/lib/dhcpcd/dhcpcd-eth0.lease'
Dec 9 17:01:01 localhost dhcpcd: eth0: executing `/usr/lib/dhcpcd/dhcpcd-run-hooks', reason REBIND

What are normal Core and Motherboard temperatures

I recently purchased a HP Probook Laptop 4530s. I installed CPUID and it says that the core temp is 56c and the motherboard is 56c is this a normal operating temp?
Nothing left in my right brain, nothing right in my left brain.

""""There's no need to use any fan control software. Besides the software only increases the fan idle speed and has no other impact. The use of it could also void your warranty.""""
first of all.....smc fancontrol does what its supposed to do...cool off your mac....when i boot in to vista and play cod4 on my mac i use fan control...it keeps the temp down....there is an impact to how fast your fans spin.....and it will not void your warranty......it is an extremely usefull tool...it will keep your video card cool when playing games....as i type this iam ripping cd's and noticed the temp at about 56celsius.....i increased my fan speed and the mac is at 37celcius...obviously this works and has a purpose....
Message was edited by: ImarkG5-osx

KLN - Free of Charge Delivery - What are the Scheduline Categories?

Dear Gurus,
1- What is the normal Schedule line category for Item Category KLN and Document Type FD?
2- What are normal goods movement too?
Regards
Chris

hi,
FD     BANS               KLS
FD     DIEN               KLX
FD     DIEN          KLN     KLX
FD     LEIH               TAL     KLN
FD     LEIH          KLN     TAL     KLN
FD     LEIH          TAX     TAL     KLN
FD     NLAG               KLX
FD     NORM               KLN     ZKLN
FD     ZMUS               KLN     ZKLN
the following are standard for FD.
regards,
balajia

What are smart mailboxes and why do i need both smart and "normal" ones?

What are smart mailboxes and why do I need both smart and "normal" mailboxes?

Hi Kingoftypos,
Thanks for that clarification. So, now it appears that the ultimate purpose of a Smart Mailbox is to point to all emails that meet the criteria in a single place, so if they are spread among several mailboxes, you will be able to see them all together. Here is an article from Apple that describes it:
A Smart Mailbox displays in one location messages that are stored in other mailboxes, so you don’t have to move messages between mailboxes. The messages displayed by a Smart Mailbox are based on criteria you define, and are automatically updated to include new messages that match your criteria. For example, you might create a Smart Mailbox that displays all messages found in all mailboxes from a specific sender.
If you change a message in a Smart Mailbox, such as marking the message as read or unread, or moving or deleting the message, the change is reflected in the mailbox where the message is actually stored.
So, adam, I would think that, if you had mail going to a lot of different places, and wanted to be able to see a particular set of those in a single place, you would use a smart mailbox. Maybe use the rules to direct your mail to different places to start with, but a smart mailbox to bring a set of common ones all together into a single smart mailbox?
Maybe you have Rules move your Amazon mail to an Amazon folder and your Apple mail to an Apple folder, but then you have a Smart Mailbox that contains any mail that has the word "Receipt" in the Subject line?
Just a thought....
Cheers,
GB

What are the normal settings to connect to wifi?

I visited my friend over the weekend and her school required me to change my airport settings in order to connect to the internet. Ever since I got back, I have been unable to connect to my usual wifi source. If I can, it drops off after a few minutes. What are the normal settings to connect to wifi?

As a minimum, the following would be the "normal settings" to connect your Mac to an unsecured Wi-Fi network. These settings can all be found in System Preferences > Network > AirPort or Wi-Fi > Advanced
TCP/IP tab: Configure IPv4: Using DHCP
Proxies tab: Nothing should be checked on this tab, except the "Use Passive FTP Mode (PASV)" option.
Hardware tab: Configure: Manually
On the Wi-Fi tab, you may also want to delete any Preferred Networks that you are not using.

I have a Win7Pro SP1 PC locked down with a Group Policy as it is a public facing PC. PDF fillable forms cannot be completed when logged on as the restricted user. The forms work as a normal user. What are the user requirements/permissions needed to fill f

I have a Win7Pro SP1 PC locked down with a Group Policy as it is a public facing PC. PDF fillable forms cannot be completed when logged on as the restricted user. The forms work as a normal user. What are the user requirements/permissions needed to fill forms?

Well, try this (I was able to fix my with these steps):
Go Utilities > Disk Utility
Select your Startup Disk, e.g. Macintosh HD
Then, under the First Aid Tab, click Verify Disk Permissions.
If there are errors, then click repair Disk Permissions.
After it is done, restart the computer and see if your problem is resolved.
I hope this help.
Zeke
www.ZekeYuen.com/blog/

What are the normal temperatures for CPU, Battery & Memory?

I am just curious as to what the normal temperatures for the CPU top, memory/power and battery are. Thanks in advance for the help!!!

No one has any idea? I am just trying to tell if my temps are normal, becuase something is definitely up with my computer.

What do the readings on the speed test actually me...

When I carry out a BT speed test, what do the readings actually mean?
Which reading tells me if I am getting anywhere near the 5.5megs my line is supposed to be able to support?
I've just run a broadband choices speed test and that simply states that I am currently achieving download speeds of 473 kbps and upload of 376 kbps, which is really rubbish!
Solved!
Go to Solution.

you a new customer and going through the 10 day training phase?
if so then breaking the connection is bad it will make the training phase longer or mess with the results it gives.
in general if theres not to much congestion at your exchange then with an ip profile of 4500 you would be able to get a download rate of 4000kbps which means you could stream 2 hd programs on two seperate systems with no pauses (providign there not wifi connected) and simultaneously browse the web on a thirde device whislt still playing games on a console, if your achievable download rate drops below 1500 then you wont be able to stream a single hd program, if it drops below 1000 then streaming high quality media will have problems and if it goes below 500 then you wont even be able to stream an audio track,
now for the hard part, regardless of what your rate is if the server is busy it wont be able to stream the content to you so pauses are inevitable, however you can often setup a program via iplayer to preload and then start the playback once its almost done (i know nobody likes waiting for things.
however the training phase your normally capped at available download rates and cant get anythign decent untill its over, sicne the training phase determins what speed is the best/ worst for your line sync and that determins what your ip profile or download rate will be, a lot of forced restarts or conection losses can and proably will result in a lot of problems with both sync speed and ip profile.
i didnt say it in the other thread about your setup problems but you would probably be better off gettign a sperate phone line for that problem device.

What are the major components in class?

1)     What is the purpose of load-of-program? When it will be trigger?
2)     Write the code for displaying the three parameters in single line with the first parameter as mandatory in the selection screen?
3)     Which event triggered whenever the user call the function BACK, EXIT, CANCEL?
4)     What are the major components in class?
5)     What is the functional module is used to get popup screen for ALV reports?
6)     Which type of pool is used to get drop-down list?
7)     What is the tcode for creating the variant truncations?
8)     Is it possible to call LDBs number of times in same report?
9)     What are the conditions to use control break statements in our report program?
10)     What is the use of range statement?
11)     What is the difference between normal reports and alv reports? With comparing to normal report are there any disadvantages in alv reports?
12)     What are the components used to suppress the fields in the selection-screen?
13)     What is the standard program to transport selection screen variants?
14)     What is the event keyword for defining event block for reporting events?
15)     What is the specific statement use when writing a drill down report?
16)     What are the different tools to report data in sap?
17)     Write the menu path to create a selection text in reports?
18)     How do we omit the leading zero s while formatting outputs in reports?
19)     What are the report truncations?
20)     How do we align selection input in single row?
21)     How do we suppress the display of input fields on selection screen?

this forum is not for answering your interview questions...if you stucked with any realtime problem then post...please try to respect forum terms and conditions.
Thank you.

What is an ageing report? What are the data sources used to develop an agin

Hello BW gurus,
I was going thru some of the BW resumes. I could not understand some of the points mentioned below. Kindly go thru them and please explain each of it.
Thank you.
TR.
     Developed AR ageing report, created invoice layout and processed invoices.
What is an ageing report? What are the data sources used to develop an aging report
     Worked on month-end and year end processes such as Balance Sheet Statements and Profit and Loss Accounts.
What data sources does one use to get Balance sheet and P&L accounts tables and fields.
     Involved in the end to end implementation of BW at Reliance Group as a team member.
What are the tasks a BW consultant normally performs when he is involved in an end to end implementation project or
a full life cycle project?
     Extensively worked on BW Statistics to optimize the performance of Info Cubes and to create Aggregates.
What do you mean when you say worked on BW statistics to optimize the performance of Info Cubes.
What are aggregates why do you need them?
     Prepared design documents from the Business Requirement documents and identified the
relevant data targets for satisfying the customer requirements.
What are the design documents does one prepare, please give an example.
Is cube a data target?

What is an ageing report? What are the data sources used to develop an aging report
Aging refers to values in different time period ranges. Example, the customer (credit) aging report can look like this.
customer (credit) for current period, 0 to 30 days, 30 to 90 days, 90 to 120 days. This is the way aging is classified.
What data sources does one use to get Balance sheet and P&L accounts tables and fields.
For P&L information, you may use 0FI_GL_6 datasource (or 0FI_GL_10 if you use ERP 5.0 version). This datasource reads the same information used in R/3 transaction f.01 (table glt0).
What are the tasks a BW consultant normally performs when he is involved in an end to end implementation project or a full life cycle project?
Requirement gathering, blueprint creation, development etc
Refer to posts on Sap Methodology and Sap lifecyle
What do you mean when you say worked on BW statistics to optimize the performance of Info Cubes. What are aggregates why do you need them?
Please check these links
http://help.sap.com/saphelp_nw04/helpdata/en/8c/131e3b9f10b904e10000000a114084/frameset.htm
http://help.sap.com/saphelp_nw04/helpdata/en/f0/3c8c3bc6b84239e10000000a114084/plain.htm
What are the design documents does one prepare, please give an example.
Design document is basically a document to say how the design is to be developed for a particular solution ex: FI it says what is the data fow and what are the data targets to be used and how data shld be stored for providing the client a solution they need.
Is cube a data target?
Yes cube is a data target.
Hope this Helps
Anand Raj

What are normal readings

Similar Messages

Maybe you are looking for