What are the criterias for supporting the Cisco AP1242?

I need to support and configure the Cisco APs. May I ask what are the additional certificates that I need other than CCNA in order to support the APs.

There are carious certification that might help. For one, the CCNA hs some wireless... you will need a background on basic route switch. Lke mentione earlier, the CCNA for wireless should have alot of information. these certifications just don't cover the 1242's. They cover RF, autonomous, LWAPP. antenna gain and power.... all the other goodies that can help you troubleshoot issues better.

Similar Messages

  • What are the Cisco 1300 series Antenna Alignment options?

    I am wondering if there are any options for aligning the antennas other than RSSI LED indications.  The cisco aironet is going to be on top of a 10m tower and the lights will not be visible. Is there any way to configure them to an audible output that would increase in loudness or pitch when the signal was strongest?

    Check this:-
    "Best Practices" for positioning Access Points (AP's) and Antennas
    https://supportforums.cisco.com/docs/DOC-16627
    thanks,
    Vinay

  • What are the features supported in Cisco Prime Infrastructure for WLAN for autonomous AP's?

    What are the features supported in Cisco Prime Infrastructure for WLAN for autonomous AP’s?

    • PI provides visibility for autonomous  clients within the same list view as lightweight and wired clients (client list  page).
    • Rogue AP detection for autonomous AP's is not supported (it's  supported in CUWN). 
    • Alarms/events for client authentication issues (e.g.  authentication failure) are displayed in PI.
    • Config management for  autonomous AP's is via CLI template.  Config comparison and archiving  functionality in PI leverages these same features that were brought in from LMS,  so need to defer to others in terms of whether this is a cross-platform feature  in PI or is only supported on a subset of platforms.  Config comparison/archive  is supported in CUWN.PI supports both infrastructure (e.g. AP Tx Power and  Channel, busiest AP, AP utilization, etc.) and client (e.g. client count, client  sessions, etc.) reports, and there are extensive reports for CUWN

  • What are the ideal settings for my TC with Shaw's Cisco DPC3825 router/modem

    My old 2nd Gen Time Capsule crapped out and now I am about to set up my new 2TB TC.  My provider is Shaw Communications and they have upgraded me to their Broadband 100 Mbps service.  This came with a new modem/router combo made by Cisco and is model DPC3825.  Before I start plugging things in I'd like to know what are the ideal settings such that I gain the most of the BB100 service.  Should I be setting the Cisco modem/router to Bridge mode or the TC?  Should I have Shaw disable anything?  Any insight is greatly appreciated.

    Unless you specifically need to have the TC perform as the main router for your network, life will be a lot easier if you configure the TC to operate in Bridge Mode.
    Whether the Cisco modem/router or gateway can possibly be configured to act as a simple bridge mode modem is one thing to consider.
    Whether Shaw would support you in the event of any connection difficulties with the modem/router configured this way is another.
    Since Shaw is your provider, it might make sense to talk with them about best practice as far as configuring the DPC3825.
    Once you have that information in hand, you will then have the answer on how best to configure the TC.....which will very likely be in Bridge Mode.

  • What are the Non SAP data sources supported for Analysis workbooks?

    AO 1.4 SP6
    BO 4.1 SP2
    What are the Non SAP data sources supported for Analysis workbooks?
    Thanks.

    HANA is a data source (which could contain non-SAP data)
    For other Excel front-ends that may connect to "non-SAP" data look at Live Office or Power BI by Microsoft - see Excel and Power BI connectivity to SAP BusinessObjects Universes | Power BI

  • What are the following:1)Cisco 1600 Series IOS WIRELESS LAN RECOVERY. 2)Service Provider Option 60 for Vendor Class Idenfier

    What are the following:1)Cisco 1600 Series IOS WIRELESS LAN RECOVERY. 2)Service Provider Option 60 for Vendor Class Idenfier
    These items are listed with 1600 series AP but I'm unable to understand what are these things & the use of them

    DHCP Option 60:  Go HERE.

  • What are the Premier, Extended and Sustaining Support Dates for Beehive?

    If you look at the Oracle Lifetime Support Policy for Oracle Fusion Middleware (found at http://www.oracle.com/us/support/lifetime-support/lifetime-support-software-342730.html), Beehive is not listed. What are the dates that Premier and Extended support end for the various versions of Beehive?

    Oracle Beehive has been added to the online Oracle Lifetime Support policy document
    http://www.oracle.com/us/support/library/lifetime-support-technology-069183.pdf

  • What are the supported Platforms and system requirements for JSE?

    What are the supported Platforms and system requirements for JSE?

    Hi There,
    The following are the system requirements & the support platforms for JSE :-
    * Solaris 9 and 8 Operating Systems (SPARC Platform Edition)
    o UltraSPARC II 450-MHz system with 512 MB of memory and 850 MB of disk space
    o Recommended: UltraSPARC III 750-MHz system with 1 GB of memory and 1 GB of disk space, or higher.
    * Solaris 9 Operating System (x86 Platform Edition)
    o Pentium III 500-MHz system with 512 MB of memory and 850 MB of disk space
    o Recommended: Pentium III 1-GHz system with 1 GB of memory and 1 GB of disk space, or higher
    * Windows 2000 and Windows XP
    o Pentium III 500-MHz system with 512 MB of memory and 850 MB of disk space
    o Recommended: Pentium III 1-GHz system with 1 GB of memory and 1 GB of disk space, or higher

  • Is there any commercial support for LCCS services? What are the associated SLAs

    Hi,
    Following are some queries regarding LCCS.
    Is there any commercial support for LCCS services? What are the associated SLAs of the support and the cost?
    Can I Using applications developed using LCCS for commercial purpose?
    Does Adobe allows its LCCS service customers to offer applications developed using LCCS API for 3rd party commercial usage.
    Thanks & Regards
    Amit

    Hi,
    We were selling LCCS to enterprise customer under a different licensing program, but have since stopped the sale of that.
    You should check out this thread - http://forums.adobe.com/message/4110049#4110049 for a discussion on this.
    Jeff

  • What are the supported Macintosh Operating System versions for IBM SPSS Statistics 18,19 and 20?   Question  I would like to know what are the supported Macintosh Operating system versions for IBM SPSS Statistics versions 18, 19 and 20? Answer  Please see

    What are the supported Macintosh Operating System versions for IBM SPSS Statistics 18,19 and 20?
    Question
    I would like to know what are the supported Macintosh Operating system versions for IBM SPSS Statistics versions 18, 19 and 20?
    Answer
    Please see the list below:
    - IBM SPSS Statistics 18 and 19 releases are supported on Apple Macintosh OS 10.5 (Leopard) and 10.6 (Snow Leopard) with Intel processor.
    - IBM SPSS Statistics 20 release is supported on Apple Macintosh OS 10.6 (Snow Leopard) and 10.7 (Lion) with Intel processor.
    - The IBM SPSS Statistics versions 18 and 19 are not supported on Mac OS 10.7 (Lion).
    THIS MEANS THAT TO USE LION ONE FIRST HAS TO UPGRADE TO SPSS STATISTICS 20.

    Whilst the 2012-02-15 edition of IBM's matrix does not mention Lion, a few users have noted that:
    • 18.0 can be troublesome
    • an updated version of 18.x should be better.
    Related files
    PASWStatistics_1 803_Mac_Patch.dmg and IBM SPSS Statistics 18.0.3.4 Hotfix Mac.zip are no longer available from the spss.com domain, and I could not find them in an IBM domain. If you download from unofficial sources, proceed with caution.
    Related pages
    In Apple Support Communities:
    • will PASW (SPSS) 18 work with LION
    • PASW statistics 18 crashes every time
    • Java Virtual Machine & SPSS 18 with a question from me.
    Elsewhere:
    • SPSS on Lion « Decorator Pattern
    • SPSS / PASW Mac Patch 18.0.3 and Graphing Fix | The Personal Website of Philip Fizur
    • Patching PASW 18 (or SPSS 18) for Mac OS X (Leopard, Snow Leopard, Lion) to version 18.0.3.1
    • and other sources, including one domain that I treat as reputable but I'll respectfully not share that link here.
    At a glance, you might find that 18.0.3.4 is compatible with Lion.

  • Can I migrate from WCS 7.0 to PI 1.2. If so, what are the guidelines for migration?

    Can I migrate from WCS 7.0 to PI 1.2. If so, what are the guidelines for migration? Do we have any Instructions/steps?

    Migration from WCS 7.0 to PI 1.2 can be  performed. If the customer wants to migrate data you need to first upgrade to  NCS 1.1.1  You can download NCS 1.1.1 from Cisco.com if you have a valid service  contract.
    For the migration step involving NCS an evaluation license is  sufficient.  You can obtain an NCS evaluation license from http://www.cisco.com/go/license >  Get Demo > Network Mgmt Products > Cisco Prime NCS Evaluation License.  
    Instructions for migrating data from WCS 7.0 to NCS 1.1.1 are available in  NCS 1.1.1 Release Notes.  Do not upgrade to NCS 1.1.2 as this release is not  upgradeable to Prime Infrastructure 1.2.  If you are ordering a Cisco Prime  physical appliance (PRIME-NCS-APL-K9) be sure to select the NCS 1.1 image which  you can later upgrade to Prime Infrastructure 1.2 after you have migrated your  WCS data.
    There is a post in the support forum which can be refered.
    https://supportforums.cisco.com/docs/DOC-26972

  • What are the general effects of using recovery mode, and is it possible for one's data to be backed up on to it afterwards?

    My iPad, in my opinion is a great device to have whenever I need to use it for work - mainly using it for creating music.  However I feel that it's a bit outdated, and I plan to get a new iPad Air for this holiday season and give this one to my children.  That being said, I have stumbled across a weird problem that keeps me from backing my iPad (generation 2) up to my computer.  The error in question states that "The iPad is currently owned by another computer."  By looking around on the internet, I was able to deduce that one of the ways to solve this problem was to put it in recovery mode to get rid of the 'ownership', and this seems logistical.  The problem I'm facing now, is that, after trying to find the answer, I do not know how recovery mode has an impact on all the data stored on my iPad.  To clarify the question into three parts:
    1)  Is there a way to back up files from my iPad and easily retrieve them without the use of iTunes?
    2)  If not, is there a way to get rid of the 'ownership' of another computer other than recovery mode WITHOUT jailbreaking it?
    3)  If still no, then what are the effects of putting my iPad into recovery mode, and will all of my songs and data be safe?
    Thank you for answering, if possible.

    Was the iPad originally set up on a different computer, and hasn't been synced to the one that you are now trying to use ? There are some instructions on this page for syncing to a new computer : https://discussions.apple.com/docs/DOC-3141
    (Before trying that you could copy any important files/documents off the iPad so that you have you own backup copy of them e.g. depending upon what the apps support then email them to yourself, use Dropbox, copy them to your computer via your wifi-network.)
    You should be able to copy iTunes purchases off the iPad and over to that computer's iTunes via File > Devices  Transfer Purchases, but if you have music from other sources (e.g. copied from CDs) which aren't in that computer's iTunes (and you haven't got a backup to copy them onto it from) then there are some programs listed half-way down this page which should be able to copy them back : https://discussions.apple.com/docs/DOC-3991
    For recovery mode, that will result in your iPad being put back to factory defaults i.e. all of your content will be removed from it

  • I´ve bought the new IPad3, what a disappointment the 3G does not work, no Internet available, APPLE what are you doing for the all the people in Germany who bought the new IPad3? I´m still an Apple fan, all my products are from Apple but I need a solution

    I have been waiting since months for the new IPad4G 64 Gbt. ON recommendation of Apple Support I have changed my IPad 4G last week in the hope that something was wrong with the firts one I bought.
    The one I have now has the same problems. WiFi is working however 4G not at all. Apple what can I do? What are you doing for the thausands of German Apple fans who have bought a IPad4G and can not use it. We need a solution NOW. I´m working with this tool and need to be able to rely on it.
    Thanks for a feed back.

    JKerki wrote:
    They had not heard about the problem, however made no problem to change it for an other one. Apple Support Germany pretendet not to know about this problem. However the web is full of complaints.
    It would be advisable for Apple to react officially on it. € 799, - for something that doesn´t function is no fun :-((
    Isn't replacing your iPad Apple "officially" acting on it?

  • What Are the Exact Basic rules for Replying a Thread...... -:)   @};-

    Hi Experts,
    After Looking into the forums many days I had a small conclusion about forums,
    SAP Forums are better place I have seen for getting a goo dhelp & Knowledge...
    Why can't we make it a BEST Place.
    This is just a small doubt which I would like to clear myself first,
    I have seen many users In the forums asking for a Basic Questions
    When cleared, But still they want to have a Spoon feeding with a Sample Code.
    When Sample Code Given they will provide the original code and requests for Modifications.
    These always looks to me as crazy.
    I have seen somelong time agin by moderators posting that In SCN there will be no SPOON FEEDING.
    I am not sure whether if still this Rule AVAILABLE or NOT.
    Ok if the task is really difficult let them ask again and again,
    And it was not replied, let them repost, I agree with them.
    And How about a User Registered in SDN very long back and asking for a silly question in below thread,
    [Sendin Email to the recipent list -Need correct FM |Getting the address from shipto partner of Bil. item not directly from C.ma]
    This is one more example, really funny, The thread poster needs the solution at any cost, he doesn't require and Suggetions,,, {He Only needs Solution}
    [Radio Buttons |Radio Buttons;
    [Turning Off Debugger |Turning Off Debugger;
    [Regarding Amount in words|Regarding Amount in words;
    There are 100's of threads like this....Everyone knows this facts.
    Check this who answered this one and who replied correct answer, who copied, finally who was rewarded...!
    [how to validate POsting period |Re: how to validate POsting period]
    Now My Real Problem is....!
    User is always intelligent, Only the weakness is in Contributor, trying to help them,..,
    And I openly say that Someone requesting for basic help is not DUMB, But the Contributor replying forgets
    the basic rules " Why Contributing ?"
    According to me It's not the Requestor to see Rules & Requlations before posting the threads,
    But its responsibilty for the Contributing person to see th Rules & Requlations before replying the threads,
    If we follow the rules and stand on a single word or rule or anything there will be Good Result.
    Major Problem is in US not anyone else.
    Example Some one saying search in the forum,,, then please no replies after that...
    But we are very pity hearted again we post the solution,,,
    But it is not at all enough(for cintribtor's)... they will copy the solution and post again by slight Modifications,
    And Some users are having 500,600,700,800 Posts with 0 points, registered long long back.
    They are completly dependent on forums,,, As they goto office and as they eat, The same they open forums and ask Queries...
    They will never realize what they are doing,, and we will never let them improve better...
    Finally Lets Discuss About this and Correct & Suggest me if I am wrong,
    Is my thoughts are going in the right way or not I am not even sure... Please Aslo Correct me if I did any mistakes.
    Thanks & regards,
    Dileep .C
    Edited by: Dileep Kumar Chinnaiah on Apr 29, 2009 12:33 PM
    Title Changed Form
    "What to do when someone asking for Basic Questions" to "What Are the Exact Basic rules for Replying a Threads...... "

    Hi Stephen,
    Very useful Information,
    First tell me a little something about my self...
    After completion of my certification(as a fresher) I was down the streets hunting the job,
    with the insufficient knowledge and being a non-experienced person, I never got one.
    And mean while when I got my "S-UserID", I used to be proud, To say frankly, I registerd in SDN & SAP all at a time, without even knowing what I can do there..,
    When I got a job afterwords I was doing the job and never seen SDN page for many months,
    when I came to know that of we have doubts we can post at SDN. then started requesting help,
    I posted only a little, I didnot got the proper response. on that day I decided,
    still there are some places where we cannot get help on time and there will be people waiting to get help,
    Why cant I put some of my efforts to help others.
    Then I searched some topic by Topic in SDN topic by Topic I used to read threads just for knowledge.
    when I feel my self comfort for contributing, I started contibuting...!
    If you haven't read it, take a look first, so you can understand where things are now.
    I dont know where things are now. But these in this thread I mentioned clearly what I seen from the day I started contributing.
    I searched with the terms of 'Rules for replying', The results are not as I expected, and this link has subject as
    "O SDN, where art thou?" So it dosent hit my in the list.
    Like everybody until a certain stage I am also rushing for points.
    But I most cases I never tried to copy paste answers. If I done some then that is just to point it myself some day,
    I have no hopes or no intrest on the points...! This was discussed with Rob & Matt, at my inital contribution where my points are 36.
    From that day till date I have changed a lot to myself.
    Everyone cannot change like me because they are not like me & And I dont even expect that...!
    I will be online almost 6-8Hrs a day, Not even getting intrest to see the forums just because of the co-contributors.
    My only point is I am just requesting to a co-contributor,
    Clearly In a example : Lets say contributor has replied to a thread, and if you know that is a correct solution,
    please dont reply any more, If you have a better solution than that, then only reply,
    Even there is one reply in the thread not a matter, if correct answer leave that query.
    If still error persists, Show up with your Idea's...
    Dont let down the contributor, by copying his reply and editing and pasting(edit only if incorrect).
    I am just looking for this one exactly to circulate between ourselfs.
    For this we a little support from moderators to circulate(may be as a rule or may be as a mail to them)
    You may say again how many mails we have to send, It dosent matter, one mail to one person one time,
    and +ve factors will show up definetly.
    A real contributor always understand what I am talking about, but some one who hunts for points will never.
    I am really sorry if I am troubling with my doubts & requests,
    If so, Pleae forgive me,,
    Thanks & regards,
    Dileep .C

  • What are the cause and fix for the following error message? NS_ERROR_FILE_ACCESS_DENIED failure code: 0x80520015

    Every time I close my Firefox browser I receive the following error message (see details below).
    FYI:
    -- I am running the current version of Firefox.
    -- I had no problems with this error message until my computer was recently attacked by 2 viruses:
    ` SystemFix
    ` Win7 Antivirus 2012
    Both viruses have since been cleaned from my computer. However, I am still receiving this error message.
    Here are my questions:
    * What are the cause and fix for this problem?
    * Do I need to uninstall and reinstall Firefox?
    * Is it possible that this error message is related to an add-on and that it has nothing to do with the recent virus attacks?
    I look forward to any feedback and support you might be able to provide.
    Thanks,
    Metta
    Error Message
    NS_ERROR_FILE_ACCESS_DENIED
    Component returned failure code: 0x80520015 (NS_ERROR_FILE_ACCESS_DENIED)
    [nsIFileOutputStream.init]
    File: undefined
    Line: 857
    Stack: undefined

    Every time I close my Firefox browser I receive the following error message (see details below).
    FYI:
    -- I am running the current version of Firefox.
    -- I had no problems with this error message until my computer was recently attacked by 2 viruses:
    ` SystemFix
    ` Win7 Antivirus 2012
    Both viruses have since been cleaned from my computer. However, I am still receiving this error message.
    Here are my questions:
    * What are the cause and fix for this problem?
    * Do I need to uninstall and reinstall Firefox?
    * Is it possible that this error message is related to an add-on and that it has nothing to do with the recent virus attacks?
    I look forward to any feedback and support you might be able to provide.
    Thanks,
    Metta
    Error Message
    NS_ERROR_FILE_ACCESS_DENIED
    Component returned failure code: 0x80520015 (NS_ERROR_FILE_ACCESS_DENIED)
    [nsIFileOutputStream.init]
    File: undefined
    Line: 857
    Stack: undefined

Maybe you are looking for

  • Acrobat 9.1 won't open pdf file??

    Just downloaded the updated Acrobat reader and am trying to open up a file manual for a toshiba dvd vid recorder and keeps saying need acrobat reader 8 or 9 to open--even after it shows installed in my programs. Help--art tx

  • Indesign RGB color problems and JPEG export

    How do I get a bright red or bright lime green RGB jpeg to show properly on an InDesign page? I click on New Color Swatch, Color Mode: Web and select a web safe color, yet when I draw it on the page, the colors are incredibly dark and less saturated,

  • How to use nvl to parameter in SRW.DO_SQL  in oracle report

    Hi all, I am creating view runtime where i want to pass parameter to which i need to handle NVL below is my code SRW.DO_SQL('create view '||view_name11||' as select moqv.subinventory_code subinv, moqv.inventory_item_id item_id, moqv.item_cost item_co

  • Creative Cloud says I have it....

    I downloaded Indesign CC and in the last stages of instillation my laptop crashed. Now Creative Cloud won't let me download it again because it says I have it. What can I do.

  • Can we run BEA WL81sp2 server (trial version) on SSL ?

    Hi, Can we run the WL81 sp2 server on SSL with a trial download version ? Do we need to have a proper license for BEA 81 server to run it in SSL mode ? Any input will be appreciated. Thanks, Krishnendu