What are the magsafe 2 adapaters used for

My mac book pro has mag safe 1. What is the mag safe 2 adapter used for? Macbook air maybe? Thank you

From the U.S. Apple Store --- here are some of the things that use it:

Similar Messages

What are the transaction codes we use for LSMW in MM, SD, PP & FI/CO gnrly

Hi all,
What are the transaction codes we use for LSMW in MM, SD, PP & FI/CO generally?
Help will be surely rewarded.
Thanks and Regards,
Creasy

> What are the transaction codes we use for LSMW in MM, SD, PP & FI/CO generally?
General threads about LSMW in MM, SD, PP, FICO will be locked and deleted generally.
> Help will be surely rewarded.
&********************** Please read "the rules" if found usefull... ************************&
Cheers,
Julius

What are the best settings to use for the newest AirPort Extreme (AC wifi) with my optimum online service provider?

I have the current generation of the AirPort Extreme and a handful of devices that utilize the new 5Ghz A/C frequency. My internet speeds were blazing fast when I had first set it up but lately it has been lagging terribly. I was told that changing my dhcp did help, which it did it seems like it might be back to its normal speeds but I just want to know what are the best settings to configure for the airport so that I can get the most out of my service on all my devices? I'm using a CAT 6 cable which does help, I have a guest wifi setup with a wifi password which I understand will slow it down a little. Can anyone just point me in the right direction or just give me a step by step guide on what settings to configure? Should I really consider turning off the guest network?

I am assuming that you are looking to configure your network to provide the highest level of bandwidth possible for your network clients. If that is the case, the following are a few things to consider:
The Internet modem should support Gigabit Ethernet. That is the Ethernet connection between the modem and your 802.11ac AirPort Extreme should be Gigabit Ethernet.
Use CAT-5e or CAT-6 Ethernet cables between all wired connections.
Only expect 802.11ac performance with 802.11ac clients in the same room as the base station.
Eliminate or significantly reduce any forms of Wi-Fi interference on both the 2.4 & 5 GHz bands.
When streaming, especially HD video on your local network, use wired connections between the host and player devices when possible.
Other than the above suggestions there are no "magic" settings that you can make on your AirPort. Note: The Guest network shares the same bandwidth as the "main" network. Unless you have a network goal to provide this type of network, it is best left disabled.

[SOLVED] What are the sectors 2-33 used for?

In regard to BIOS Boot Patition for GRUB, GPT says:
Afterwards, create a new partition with gdisk and manually specify its position to be sectors 34 - 2047, and set the EF02 partition type.
Given that sector 1 is allotted for MBR, what are the remaining sectors 2-33 allotted for?
Last edited by DiamondbacK (2013-08-03 21:10:27)

DiamondbacK wrote:I'm still confused that don't sector numbers start from 1 according to Wikipedia entry on LBA?
No; from the article you've referenced:
Wikipedia wrote:blocks are located by an integer index, with the first block being LBA 0
In this context, "block," "sector," and "LBA" are more-or-less synonymous. (There is a reference on that page to sectors in the CHS scheme ranging from 1-255, but that's in the CHS system, which is not used in GPT and is pretty much history even for MBR.)
If that's the fact, sectors 2 instead of sector 1 is allocated for Primary GPT Header, and sector 3-34 have to be allocated for Primary GPT Table which need 32 sectors. Then sector 34 can't be the beginning sector for BIOS Boot Partition.
This is all based on a false premise -- or at best, a non-standard numbering system.
Does that imply the sectors 34-2047 I quoted from Arch Wiki actually means LBAs 34-2047, which is equivalent to sectors 35-2048?
Again, false premise. Whether you call them blocks, sectors, or LBAs, these units are most commonly numbered starting from 0. Certainly that's true in both GPT fdisk (gdisk, cgdisk, and sgdisk) and parted, which are the two major classes of programs you're most likely to use for partitioning in Linux.

What are the tables to be used for these reports

hello everybody,
i am a new user. it is only recently that i have started learning ABAP. i was given a rask by my faculty to develop the following reports. can anyone help me find out the tables that are used for them.
1. Report for Sales Orders due for delivery.
2. Revenue Reports based on Order Types.
3. Report for list of Pending Purchase Orders, Cancel Purchase orders.

Hi,
This depends on which fields you are supposed to show in output.Ask the person about layout requirement. How they want output of the report and which fields.
Normally Functional person will give table name also.
Here are few tables which can be useful in your requirement.
Sales Header table : VBAK
Sales Item table : VBAP
Delivery Header : LIKP
Delivery Item : LIPS
Purchase order header : EKKO
Purchase order item : EKPO
Better to concern this with u r requester and u ll get definite answer.
*MARK if this helps

What are the proper settings to use for Quadro 2100M on WS60 workstation

Hello,
I have a WS60 Workstation. When going through the settings for physix and others I noticed that the Nvidia card has no ports assigned to it.
How do I ensure that the laptop is indeed using the quadro card?
Thanks

For the Optimus structure, NVIDIA graphics is doing the rendering but it's Intel Graphics which is showing the rendered graphics on the screen. This is why you didn't see NVIDIA Graphics is connecting with any displays.
You can check the power button light, it will light orange when the dedicated graphics is in used.
(White color shows it's using the integrated graphics)

In Aperture 3.4 Export Slideshow to a video, what are the actual Data Rates used for "Best", "High", ... "Least" quality for a given resolution?

My Photo website host (SmugMug) converts uploaded video files at a specific Data Rate in Mbps before installing them. I would like to compress my slideshow video file to the same rate before I upload it to reduce file size and upload time. When I choose the "Custom" setting for an Export, I can choose 1 of the 5 Quality choices and see the estimated file size. But, I cannot know what the actual Data Rate is until after I wait a long time to export the slideshow (hours for a long slideshow) and then examine the resulting file in QuickTime Player's Inspector.

I ran a few tests using a short slideshow (16 images, 1:23 mins/secs) at 1,728 x 1,080 resolution to find out the bit rates for various quality level choices.
Export setting              Quality          Resulting bit rate          File Size
HD 1080p                    default                20.68 Mbps              214.8 MBytes
Custom                       Best                   20.49                       212.8
Custom                       High                     6.25                         65.0
Custom                       Medium                3.97                         41.3
However, I don't know if those bit rates will be the same for different length slideshows or for different output resolutions. My SmugMug host site uses an 8.0 Mbps rate for a 1728 x 1080 video file. If I choose Custom/Best, my file will be almost 3 times bigger and much higher quality than necessary, but if I choose Custom/High, my file will be smaller and lower quality than SmugMug's converted version.
I have installed MPEG StreamClip that will let me convert an exported Aperture slideshow video file, and StreamClip allows me to choose a specific bit rate in Mbps. But, I would prefer not having to do a 2 step process (Export from Aperture, then convert in StreamClip).

Hi i have an iphone 4 which is from canada nd i have seen one sim inside it which is a canadian sim ,iam staying in india so can i use that phone in india and please tell me what are the steps ihave to take for using that canadian phone in india

hi i have an iphone 4 which is from canada nd i have seen one sim inside it which is a canadian sim ,iam staying in india so can i use that phone in india and please tell me what are the steps ihave to take for using that canadian phone in india

Only the carrier to whom the device is locked can authorize it's unlocking. Contact the carrier to see if they offer unlocking and if you qualify.

What are the Corresponding fields in CRM for sales order in ECC

HI! Experts,
While creating a standard sales order in CRM I want to poulate these fields in ECC Sales order, these fields are
VBKD-BSARK - Purchase order type
VBAK-BNAME - Name: user ordered
VBKD-IHREZ - Web Confirmation Number
VBAK-TELF1 - Telephone number
Or the other way round I want to know what are the corresponding fields in CRM for these fields so that when I pass the data in crmd_order in those fields it gets populated in the above mentioned fields.
Thanks and Regards
Mayank

Mayank,
May I suggest you to create an Order in R/3 with these fields and check that back in CRM. This is not as easy as it may sound. It is possible that some of these fields are "determined" by the system - for example the "Sold-To"'s first telephone number maintained in VBAK-TELF1. So, though it becomes a part of the Order header in R/3, CRM, generally doesn't duplicate them in the transaction but allows to refer back to the master data from the transaction!
Check the following fields in CRM and see if you find the data you require.
VBKD-BSARK - Purchase order type There is a field in CRM that "holds" this value. ACTIVITY CATEGORY. This can be found in the ACTIVITY_H set of the transaction. Filed name CATEGORY. Problem with this is, - "Category Type" of a CRM Activity to be mapped to PO type? Didn't workout good for us since the master data for both vary widely. So, we used custom Header Extension data for this (EEWB). So, you have to work
VBAK-BNAME - Name: user ordered Is usually CREATED_BY in the CRM Order Header (CRMD_ORDERADM_H). But this fills up the VBAK_ERNAM bit not the BNAME.See the next item, that may give a clue if this is related to the next item.
VBAK-TELF1 - Telephone number is usually "determined". Usually the Sold-To's first telephone number maintained in the Business Partner "Communication" section for that Sold-To.
VBKD-IHREZ - Web Confirmation Number Actually it is Customer's or vendor's internal reference as per standard use. Looks like your customer is using it for custom purposes. Well, if you maintain the relationship "Is Correwspondence Recipient for" with the Sold-To partner in CRM, and maintain the details of this Person, then this will be transferred to R/3.
Hint: Once you have the R/3 order in CRM, try using the Report program (SE38) CRM_ORDER_READ in CRM. This is a good tool to "dissect and see" and order in CRM. The program needs only the Transaction Number as the input.
Easwar Ram
http://www.parxlns.com

What are the major risks buying used lenses ?

i just bought my first dslr, and i was wondering what are the major risks buying used lenses ?

You need to be able to inspect and test the lens.
Look for obvious signs of physical damage, drops, etc. (cracks, dents, etc.) A lens normally will get some signs of wear but as it's a used lens, you expect *some* wear... you're really looking for signs of damage.
Remove both front and rear caps. Look through the lens into a bright no-contrast background (a white wall, a blue sky, etc.) and check the optics. You're looking for signs of mold growth or damage to coatings. Minor dust on internal optics wont impact the lens performance... so while you wouldn't want major amounts of dirt... don't worry too much about minor bits of dust (I've actually helped prove this to someone by clipping a 3M PostIt note down to a tiny 1/4" x 1/4" size and sticking it on the front glass. Take a photo... nothing shows in the photo (even a piece of "dirt" that big wont show because the camera cannot focus on anything that close to the lens.)
Rotate the focus ring from end to end. You should feel a smooth and consistent amount of friction as you rotate the focus ring. There should be no rough spots. Listen to the lens as you do this... there should be no grinding noises.
Do the same with the zoom ring but in addition to checking for smooth consistent performance (no sticky or rough spots) you're also checking to make sure nothing seems excessively worn (nothing wobbles loose... very heavily used lenses can do that after enough wear.)
Connect the lens to the camera and make sure the camera can completely operate the auto-focus motors without a problem and/or if it's an image stabilized lens that the IS components are working.
Set the camera to max aperture (e.g. f/22, f/32.. depending on the lens) and press your camera's "depth of field preview" button (if you don't know which button is your DOF preview, check your manual. Canon tends to move that one around a bit but it's almost always on the front side of the camera near the lens mount.) You want to press and release it a few times. This will cause the lens aperture blades to stop down to the aperture you set. Release... do this while watching the lens. You should see the aperture blades move in and out (well... they snap in and out very quickly). You want to make sure it works ok, the camera gets no error codes, and there's no signs that anything is sticking.
And then there is the focus test...
Focus the camera preferably at a FLAT surface that has lots of detail.... such as the brick wall of a building. Make sure the camera is level and that the camera's focal plane is parallel to the plane of the wall. Take a test photo at low f-stop and inspect. You're checking to verify that the focus works and that the focus is reasonable across the image. As you inspect from left ot right and top to bottom you are looking to make sure the focus is more or less equal (if the right side of the image is focused... but the left side of the image is soft... it would indicate that lens elements are skewed (lens isn't collimated). It's difficult for a lens to get into this situation unless it was dropped and you'd probably see signs of damage.
Tim Campbell
5D II, 5D III, 60Da

What are the 3-bit field choices for Hw_Arm_Sel in PCI-6601

Hi,
I am programming our own driver to operate the PCI-6601. For our application we need hardware arm option. I know it is possible to use 2 counters for that, but NI-TIO should support also hw_arm. Although it is not explained in the registry document at all, after some tedious check in the DDK examples I found that this bits are located in the Gi counting mode register. I know the position of the HW_enable as well as the position of the 3 bits for pin sellect options. What I do not know is What are the 3-bit field choices for Hw_Arm_Sel . I contacted NI support but got no support. How can NI sell boards and when a customer who is not using LAbview or Measurement Studio or DDK, but is implementing his own driver is then so arrogantly turned down from NI? Also, how can NI publish just part of the registers the board support, and when a customer contacs and asks for some registers get not at all support? I can not foretell the missing registers, and it is pretty unprofessional to document just partly the registers of 660x devices. And on request you got nothing.
I hope someone from the community know about this Hw_Arm_Sel 3 pin options. Otherwise, there is just an option of error and trial. Or simply throw the board in the garbage.
Dr. Kirco Arsov
Solved!
Go to Solution.

Hi Kirco,
I have some more information for you :-)
I haven't been able to speak to the developer who is the most familiar with TIO programming since he's out of the office, but I have come across his notes from when he was writing support for the DAQmx driver.
As I described earlier, the HW_Arm_Sel bits don't select a connector I/O pin, but an internal trigger signal. There are seven internal trigger lines, and the HW_Arm_Sel bits map directly to the internal trigger signal: 0b000 - 0b111 map to 0d0 - 0d7. In order to route an I/O pin to an internal trigger, you must also write to a few more registers.
From what I've read, there are two more register families that need to be programmed: TG_x_LevelEdgeReg and TG_x_CombinationReg, where x is the internal trigger number. In your case, you only need one pin from the I/O connector to be your arm start trigger, so TG_0_LevelEdgeReg and TB_0_CombinationReg will suffice for your application.
TB_0_LevelEdgeReg :: Offset 0x660
TG_0_LevelEdgeReg is only 8 bits wide, and maps as follows:
7..6: EdgeMode
5..0: LESel
LESel selects the I/O connector pin to use as the source for the internal trigger signal. 0d0 - 0d39 will select the I/O pin of the same number. NB: behavior for TG_x_LevelEdgeReg is more limited for triggers 1-7, and only a small subset of the I/O pins can be selected for those trigger signals. Trigger 0 can use any I/O pin. Setting these bits to 0d63 forces the trigger source low, and can be used as a way to 'unroute' it when you're finished with your program.
EdgeMode determines whether the TIO will detect an edge of the incoming signal, or just pass the signal level straight through. When detecting edges, it will latch the signal and generate a single TIMEBASE3 pulse instead. 0b00 sets level mode; 0b01 sets rising edge; 0b10 sets falling edge; 0b11 sets either edge.
TG_0_CombinationReg :: Offset 0x6A0
TG_0_CombinationReg is 32 bits wide, and has three fields of interest:
19..16: CombFunction
5..4: CombTypeB
1..0: CombTypeA
CombTypeA controls which trigger subsystem to use as the source for the trigger signal. Since you're coming from an I/O pin and using the edge/level subsystem, you must set these bits to 0b01.
CombTypeB is similar to CombTypeA, and although you won't be using trigger B, set it to 0b01 to be safe.
CombFunction performs a simple logic function on A and B. Since you're only using a single I/O connector, you only need the A output, so set these bits to 0b1100.
All of the other bits should be set to 0b0.
Unfortunately, I'm unable to test these statements since my test machine is currently being used for another research project. Please let me know what happens if you decide to test.
Joe Friedchicken
NI VirtualBench Application Software
Get with your fellow hardware users :: [ NI's VirtualBench User Group ]
Get with your fellow OS users :: [ NI's Linux User Group ] [ NI's OS X User Group ]
Get with your fellow developers :: [ NI's DAQmx Base User Group ] [ NI's DDK User Group ]
Senior Software Engineer :: Multifunction Instruments Applications Group
Software Engineer :: Measurements RLP Group (until Mar 2014)
Applications Engineer :: High Speed Product Group (until Sep 2008)

What are the best dimensions to allow for iPad 3 Retina for full-page landscape images?

What are the best dimensions to allow for iPad 3 Retina for full-page landscape images?
I read an article and cannot find it that said something about trying to make it 2million pixels and JPG to keep it small, but what exactly should the dimensions be that I ultimately import? Is there some kind of a "density" setting I have to use, as well, when exporting from Photoshop, for example?

See Optimizing performance in your iBooks Author books
Density is discussed by Apple in this context as 'dpi'...
132 - iPad 2
264 - new iPad
At the top of this forum there are popular links listed on the right, including image sizing etc. Be sure to study those existing/previous threads on this topic.
Good luck.
Ken

What are the common APIs we use in oracle interface

What are the common APIs we use in oracle interface,and any APIs are there for validation Of data During Tranfer to interface table.
How to find Api s in oracle applications in Individual modules

For 11i, all public APIS are listed at http://irep.oracle.com
For R12, use the "Integration Repository" responsibility in your R12 instance to list the APIs available in that instance
HTH
Srini

What are the allowable dimensions of screenshots for ibooks?

What are the allowable dimensions of screenshots for ibookes? I know the requirement is very specific.
And what is the best tool to do so? I tried to use the native screenshot tool but it is hard to make the size precise.

Minimum size is 600 pixels in the shorter dimension. Maximum size is 2048 pixels in the longer dimension. That's what you get when you take a screenshot on a new iPad. (There is no point in having something larger than this.) Screenshots taken with an older iPad are 1024x768.
For my book, I just took screenshots on an iPad 2 (1024x768) and used those. They were accepted without complaint.
Michi.

What are the defaul username and password for SQL Plus ?

hello, what are the defaul username and password for SQL Plus ? i'm using the client 11.2.0.1

You'll need to download the full database installation files for the platform you are using. They are two .zip files, about 2.2 gig total.
I'm not going to give you the link because you should be able to find it easily. You have to read and accept the license agreement anyway.
When you install it, you'll be given several options about the type of database you want.
But before you install anything, you should read the installation manual for your platform.

What are the magsafe 2 adapaters used for

Similar Messages

Maybe you are looking for