What are the steps u followed in your project

Hi....
he asked me like this
1...what are the steps u followed in your project?
thanks and regards,
k.swaminath reddy.

Hi,
1.Discovery of problems
2. Expectations
3.develop solutions...
4.Implement Solution...
4.1 Installation
4.2 Testing
4.3Training
4.4Support
5.Project Closedown

Similar Messages

What are the steps to follow after you install a new Hard Drive on a 17in Macbook Pro mid 2009

I plan on installing a larger Hard Drive..the physical part is simple..but what are the steps after you close it up and hit the power button? Is there softwre on the mother board that will start the unit running??

A new Hard drive will not be Mac-formatted, so you will have to do that first. A copy of Disk Utility to do the job is also on the 10.6 Installer/Utilities DVD.
Boot to the installer DVD, but do not Install. Answer only the "what language" question, and wait a quarter minute for the menuBar to be drawn. Choose Disk Utility from the Utilities menu that appears.
Select the Hardware_name of the new Drive. Partition, one partition, ( Options ), GUID partition table. Name the partition: MacIntosh HD and choose Format: Mac OS X Extended (journaled). It will complete in a minute or two, as it only rewrite the Directory area.
If you wish to shake out your drive, you can erase it and Security Erase, Zero all data, one pass. But this takes HOURS.

What are the steps to follow before disabling iCloud?

After working a while with my iMac running Mountain Lion in combination with iCloud, I have to disable iCloud because I'm going across the ocean for a while. I don't want to end up with a huge bill because every time I use my iPhone, it will sync (while no Wi-Fi available).
As a matter of fact, I already archived my Contacs, Calanders and Reminders (Notes doesn't have such a feature), but it seems to put everything back to the iCloud account after importing.
My question is: What is the step-by-step approach to disable iCloud (both iPhone and iMac) without losing any data?
Many thanks in advance!
Cheers,
GJ

Thanks a lot, mende1!
It works. (Only Notes is set up differently, but that's not a real issue for me.)
If I do the same on my iMac, I don't get that question. Is there a possibility to restore these data from my iPhone to my iMac?

What are the steps to publish Captivate 6 project for use on an iPhone?

I found this URL: http://blogs.adobe.com/captivate/2010/09/publish-to-iphone-from-captivate-5-and-elearning- suite-2.html
But this seems dated.
Here's what I just tried:
- Hit Publish
- Checked the SWF AND the HTML5 boxes in teh Output Format Options
sent the xx.htm URL to a friend with an iPhone to have her try it (by clicking the URL)
She said it gave her an error about not being able to run it (needing the flash Player)
I checked my project (very simple one) via 'HTML Tracker' and it listed nothing in the 'unsupported Slide/Object' list)

Vish-
Thanks for the response
I'm using Captivate 6.0.1.240 (the trial version)
My tester friend who has an both an iPad as well as an iPhone gave me some more updates this AM
.. Running in the iPad, everything was looking good, including the drag and drop
... Running on the iPhone (smaller screen), she reported the following: a simple quiz screen with multiple choice radio buttons - the actual radio buttons disappeared (see http://download.insight-experience.com/Tom/Captivate/iPhoneNoRadioButtons.PNG)
Then i tried it on an iPod Touch.. I launched the same URL from our webserver via safari browser
It brings up the initial screen with the playbutton (arrow in a circle).. I press that button. It does something for a second or two and then the browser window shuts down and the ipod touch goes back to the main iPod screen with all the buttons to launch the different applications.. I've tried this a few times and the same thing happens.. Basically it seems like the captivate project file is shutting safari down for some reason.
Any ideas on this one?

What are the steps we follow while customizing the Deltas in Bw side

Hi All,
I had a query regarding the customization of deltas in BW side after replicating from R/3.
thanks and regards
kabir

Hi,
In order to customize the deltas for the different DS are depends upon the type of the DS you are using for ex. if it is from LO cockpit then you need to take care of
the delta setups but you can do the setting for Jobs.
In case if you have any generic DS you can customize the delta at RSO2 transaction by selecting the one of the delta feild from the DS..
Hope this helps..
assign points if useful.
Cheers,
Pattan.

HT5787 I forgot to answer the secret question camels Store account and you follow the steps in the site account settings but I have not got any mail explains what are the steps involved

I forgot to answer the secret question camels Store account and you follow the steps in the site account settings but I have not got any mail explains what are the steps involved

Call your contry's number from http://support.apple.com/kb/HE57 and ask to speak with Account Security.

I need to transfer settings from my Macbook to a new Macbook pro. what are the steps I need to follow?

I need to transfer the settings (mail, safari, etc.) from my Macbook to a new Macbook pro. what are the steps I need to follow?

Time Machine will sort that out, you got an external HD ?

HT1657 What are the steps in watching a rental that was purchased and downloaded to your iphone 4?

What are the steps in watching a rental that was purchased and downloaded to your iphone 4? or to watch on a home laptop?

In order to watch it, just start playing it - if you've downloaded or synced it to your iPhone then it should be in the Videos app, or if it's on your computer's iTunes then it should be in the Movies section of your library. You have 30 days to start watching it from when you rent it, and once you start watching it you then have 48 hours (24 hours in the US) to finish watching it. As long as the film has been fully downloaded downloaded then you should be able to watch it without being online.
There is a FAQ page about rentals here : http://support.apple.com/kb/HT1657

What are the steps i need to follow to refresh the database

Hi Team,
I am the junior DBA first time i need to do Database Refreshment on UNIX platform.
1. Database Names are different and mount points are diffrents.
2. Synonyms and dblinks are should be retained.
How to do this and what are the steps i need to follow.
Please suggest any one.
Regards,
Venkat.

Venkat wrote:
Hi,
Version is Oracle 10g.
Venkat..Start here: http://docs.oracle.com/cd/B19306_01/backup.102/b14191/rcmconc2.htm#i1006532

What are the steps we have to follow to develop RFC function module

hi
what are the steps we have to follow to develop RFC function module

I will tell you simple example within r/3 systems..
source system - A (SAP R/3 )
Destination System B (SAP R/3).
First create RFC Destination in SM59 - in A System.
Createing RFC Destination - GOTO SM59 Transaction and click R/3 System .
it will go second screen and give ur RFC Name ,IP Address and log on details.
click on test concetion and remote logon.
now create RFC Function module in B System.
goto se37 - create fm with starting with Z* or Y*.
maintain all data like
attribute should be remote enabled
importing is v_matnr
exporting is v_maktx.
write the simple code - select single maktx from makt into v_maktx
where matnr = v_matnr.
Call this fm in report program in se38 in B sytem and copy the FM.
paste this code A System
use ur logic and destination 'RFC Name'.
Reward Points if it is helpful
Thanks
Seshu
Message was edited by:
Seshu Maramreddy

What are the steps followed inaggregatation level bi-7

what are the steps followed inaggregatation level bi-7

hi,
chk these links
http://help.sap.com/saphelp_nw04s/helpdata/en/43/1c3c7031b70701e10000000a422035/frameset.htm
http://help.sap.com/saphelp_nw04s/helpdata/en/43/2861d1e036400ee10000000a11466f/frameset.htm
http://help.sap.com/saphelp_nw04s/helpdata/en/43/293f3414483fe1e10000000a11466f/frameset.htm
Ramesh

What are the steps to make it seamless for a customer to use the install program and then use the installed program?

I wrote an install program (.exe) that is downloaded from a website. When run, it 1) leads a customer to browse to a directory, and 2) copies files (.exe, .dll, etc.) from a website to that directory. When I run, the installed program works.
What are the steps to make it seamless for a customer to use the install program and then use the installed program?
bhs67

This site https://msdn.microsoft.com/en-us/library/vstudio/2kt85ked%28v=vs.110%29.aspx provides a basic description of the Visual Studio Windows Installer.
Near the bottom of the page is "You can unlock all the features of InstallShield by paying to upgrade to the full version of InstallShield." Where do I find info that describes the differences between the "free" and the "full"
versions?
bhs67
Hello,
The default feature does support the task for your requirement, so there is no need to pay for the other features unless you want to use some feature which is not free.
In addition, as this thread
InstallShield LE not available with VS 2012 RTM? shared, even through there is a link to InstallShield LE in the New Project dialog under Deployment solutions, but it belongs to third-party that I would recommend you consider posting this issue
at the following forum to get supports about InstallShield.
http://community.flexerasoftware.com/forumdisplay.php?133-InstallShield
Regards.
Carl
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

What are the steps to change the name on the "House" in the side bar on OSX Mavericks?

What are the steps required to change the name on the "House" in the side bar for OSX Mavericks?

You want to change your username. First, make a backup of your files with Time Machine, as any error may damage your user.
Then, follow these steps to change your username > http://support.apple.com/kb/ht1428 Be very careful, as it requires to log in as root

What are the steps in oracle 11g DBREFRESH

Dear Techies,
Please help me on below. I followed all steps in db refresh
I have done till
Alter database open resetlogs
status is open
what are the steps remaining in oracle 11g dbrefresh from PRD to QTY. is there any post steps to drop old ops$users.
Please let me know.
Thank you
Best Regards
RJ

Hi Gurpal,
Thank you for your valuable reply
Do I need to do your mentioned steps after below steps
RECOVER DATABASE USING BACKUP CONTROL FILE UNTIL CANCEL;
AUTO.
once recovery is done CANCEL.
Alter database open resetlogs.
status is open.
AS YOU MENTIONED
Make sure listener and DB should be up.
Determine Schema Owner
SQL> SELECT OWNER FROM DBA_TABLES WHERE TABLE_NAME = 'T000';
Check the OWNER of “SAPUSER”
SQL>SELECT OWNER FROM DBA_TABLES WHERE TABLE_NAME = 'SAPUSER';
Create OPS$ User
Use the oradbusr.sql script. This script is attached to the note 50088. The script is valid for Oracle and UNIX. Use the following syntax
SQL> @ORADBUSR.sql SAPR3 UNIX (SID) X
Check the OWNER of “SAPUSER" after exceute command
SQL>SELECT OWNER FROM DBA_TABLES WHERE TABLE_NAME = 'SAPUSER';
If the system returns an owner <owner> other than OPS$<sid>ADM (OPS$SIDADM) of PRD, you must
delete the relevant SAPUSER tables:
SQL> DROP TABLE “OPS$SIDADM".SAPUSER;
and after that check the output of (R3trans -d)
set the value in profile parameter
To ensure no background jobs after the start (Rdisp/wp_no_btc =0)
(Login/no_automatic_user_sapstar =0 )
or Any table spaces need to be create ???? PSAPTEMP ??? or any.
Thanks & Regards
RJ

What are the steps applying incremental backups to standby database 11g

Hi All,
I have built 11g none ASM standby database from ASM RAC Database. Now I want to apply incremental backup to the standby database from primary but not sure how to do it. I tried following and I had an error “ORA-01103: database name 'ins-prim' in control file is not 'ins-sec'”
1- I have configured standby database with RMAN backup.
2- After finishing installation, I took a incremental backup from primary server(ins-prim) and moved incremental backup and control file to the standby (ins-sec) database
3- I stared standby database nomount mode
4- restore controlfile from “incremental backup location in standby database”
5- alter database mount; and got this error
“ORA-01103: database name 'ins-prim' in control file is not 'ins-sec'”
What are the steps applying incremental backups to standby database with 11g?
Thank you

I build the database from backup and changed from ASM to none ASM and changed location of data files and logfiles. I think this changes makes the standby database as logical one.
You can a have a physical standby with different locations for everything (redo/controlfiles/datafiles), ASM and no ASM etc. I have a such a configuration in production (10gR2)
I build the database from backup
Are you sure you have a standby ? Ins-sec receives the archivelog files from the primary ? How did you proceed to build this database ? I suspect you don't have a standby at all ! If you have duplicated the database ins-sec and ins-pri are independent databases and you won't be able to apply an incremental backup (your script was not correct but it is another story)

What are the steps u followed in your project

Similar Messages

Maybe you are looking for