What cable type for connecting with gigabit port

What kind of lan cable that I should use for connecting with gigabit port from Time Capsule to get the fastest transfer rate. And what is the maximum rate MB/sec that could be?

You can use CAT5 or CAT6.
max transfer rate is:
Fast Ethernet has a theoretical speed of 100 Mbits/sec (12 MB/sec), while Gigabit Ethernet has a theoretical speed of 1000 Mbits/sec (120 MB/sec). That suggests a double speed advantage of Gigabit Ethernet over USB (60 MB/sec), but neither protocol hits its maximum. In reality, a typical USB connected disk is roughly equal to or lesser than the throughput of a shared drive attached over a Gigabit Ethernet network.
Over wireless network:
- 802.11b has a theoretical speed maximum of 11 Mbits/sec with a typical transfer rate of around 4.5 Mbits/sec (0.5 MB/sec) with an ideal signal.
- 802.11g has a theoretical speed maximum of 54 Mbits/sec, with a typical transfer rate of around 23 Mbits/sec (2.5 MB/sec) with an ideal signal.
- 802.11n has a theoretical speed maximum of 300 Mbits/sec, with a typical transfer rate of around 74 Mbits/sec (9.25 MB/sec) with an ideal signal.

Similar Messages

My wall charger is showing sign of charge but it's not charging, last three days I charged my iphon to mac book pro, what can do for charge with my wall charger. And I tarted also 3 deferent chargers wich is working with other iPhones but my iphon is not.

My wall charger is showing sign of charge but it's not charging, last three days I charged my iphon to mac book pro, what can do for charge with my wall charger. And I tarted also 3 deferent chargers wich is working with other iPhones but my iphon is not charging it's only showing the sign of charge.

Hi there Zeeshan Saeed Al Barvi,
I would recommend taking a look at the troubleshooting steps found in the article below.
iPhone and iPod touch: Charging the battery
http://support.apple.com/kb/HT1476
-Griff W.

What OS x for iMac with 1 GB

What OS x for iMac with 1 GB?

Depends which iMac...
At the Apple Icon at top left>About this Mac.
Then click on More Info>Hardware and report this upto but not including the Serial#...
Hardware Overview:
Model Name: iMac
Model Identifier: iMac7,1
Processor Name: Intel Core 2 Duo
Processor Speed: 2.4 GHz
Number Of Processors: 1
Total Number Of Cores: 2
L2 Cache: 4 MB
Memory: 6 GB
Bus Speed: 800 MHz
Boot ROM Version: IM71.007A.B03
SMC Version (system): 1.21f4

What cable(s) for audio on hp zr2440w monitor with HP 3005pr port replicator and HP Folio laptop?

I have an HP ZR2440w monitor.
I have an HP Folio laptop.
I have an HP 3005pr port replicator.
I want to use the monitor's built-in speakers.
Question 1) What cable do I need to connect the port replicator to the monitor to use the monitor's built-in speakers?
Question 2) Does the monitor have a built-in microphone?
Question 2b) If yes, what cable do I need to connect the port replicator to the monitor to use the monitor's built-in microphone?
Thanks!

I understand you have some questions connecting the zr2440w monitor to the Hp 3005pr port replicator.
The back of the replicator should look something like this.
Question 1) What cable do I need to connect the port replicator to the monitor to use the monitor's built-in speakers?
The green headphone jack is how you would connect it to a set of external speakers. If the monitor has its own speakers, it should have a port to match it. This is a standard 3.5mm audio jack, so any standard 3.5mm speaker cable should work. I will note that this monitor didn't list any audio input. Monitors that have speakers usually have an analog audio input jack.
Question 2) Does the monitor have a built-in microphone?
This guide lists all the features of this monitor starting on page 2. It doesn't appear to have a microphone. You could still connect an external microphone to the port replicator's microphone jack.
Let me know if this answered your questions.
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

What is the driver name to be given for connecting with an MSAccess database?

I tried the 32bitODBC test on the MSAccess database. Works fine. My loaded java program trying to connect with the database is still not working. NullPointerException runtime error.
Maybe the driver that I've loaded is wrong viz. sun.jdbc.odbc.JdbcOdbcDriver.
What is the correct drivername to be given in class.forname("driverName")?
Any clues?

what u've given as the driver name is correct. The NullPointerException comes because of problems with passing parameters from the front end to the database. It's receiving null parameter values. Check the parameters u r passing to the database. I think this will solve the problem.

What cable/adapter for trv-530 to imac

4 pin, 6 pin, firewire 400, firewire 600, firewire 800
AAAAAAAAAAAAAAAAAAAAAAaaaaaaaaaaaaaaaaaaaaaaaaaaa..................
I have an old Sony TRV-530 which I used to record some video because I needed a very wide angle lens which I happen to have for the TRV-530. Now how the heck do I get it into iMovie. I kind of came to the conclusion that I need to do this thru firewire but my iMac (21.5 late 2009, 10.7.2) has a different firewire connector than the cable that comes out of the TRV-530. What cable or adapter do I need and where can I get it? A model number would be greatly appreciated!
Thanks,
Joe B

Hi MeeToo
The Early white Intel iMac's have a Mini-DVI port and you can use either a Mini-DVI to DVI or Mini-DVI to VGA adapter with that display, however the Mini-DVI to DVI adapter and DVI cable is the better connection.
http://store.apple.com/us/product/M9321G/B
Dennis

Slow internet connection with gigabit ethernet?

I have a 1Gbps (1000Mbps) internet connection from my ISP, using the internet speed testing service provided by local authorities, my internet download speed is shown to be at least 250Mbps (close to the max limit of the test) when my iMac directly connected to my wall ethernet socket.
However, when Mac is connected to the internet through my 2012 Time Capsule (all ethernet and time machine disabled), my internet download speed is slowed to 96-98Mbps.
I understand that all ethernet ports on the 2012 spec Time Capsule is gigabit ethernet, and I have checked my connection using the network utilities, which confirms that my linkspeed is 1Gbps. The hardware tab on my Network preferences also shows that my ethernet is set to 1--base T, full-duplex.
So where did the 60% speed decrease come from?   Is this ~96-98Mbps speed limit a hardware limitation? Or is my time capsule set up incorrectly?
I understand that similar questions might have been posted in the forum before, but I haven't b thread with the exact issue I described above.   Any help would be appreciated.

Many thanks for your incredibly detailed reply. All the information in your solution is correct, and while it did not directly solve my problem, it would have taken my a lot longer to figure out the issue without the information you provided.
I didn't realize we're missing so many functions in airport utility 6.0.
Anyways, upon reading your advice, I installed Airport utility 5.6 on mountain lion and checked the link speed settings.    Apparently it was automatically set to 100Mbps when connected to my cable modem.
Strangely, if I manually change the link speed to 1000Mbps full duplex, Time Capsule would report an "ethernet unplugged" error along with the consequential "internet connections" and "no DNS servers" error.   Since my ISP has been supporting consumer 1Gbps internet for a few years now, and since I am able to get an over-100Mbps actual link speed with directly connection to my cable modem, I am certain that my cable modem connection supports 1000Mbps local connections.
Many thanks for your incredibly detailed reply. All the information in your solution is correct, and while it did not directly solve my problem, it would have taken my a lot longer to figure out the issue without the information you provided.
I didn't realize we're missing so much functionalities in airport utility 6.0.
Anyways, upon reading your advise, I installed Airport utility 5.6 on mountain lion and checked the link speed settings.    Apparently it was automatically set to 100Mbps when connected to my cable modem.
Strangely, if I manually change the link speed to 1000Mbps full duplex, Time Capsule would report a "ethernet unplugged" error along with the consequential "internet connections" and "no DNS servers" error.   Since my ISP have supported consumer 1Gbps internet for a few years now, and that I am able to get an over-100Mbps actual link speed with directly connected to the cable modem, I am certain that my cable modem connection supports 1000Mbps local connections.
You're also correct in that Time Capsule does not have a settings for "half duplex" for 1000Mbps link speed. But hooking my my mac directly with my cable modem, Mac network preference pane reports that the 1000Mbps connection between my mac and cable modem is full duplex, so my ISP does allow full duplex 1000Mbps connection.
After NUMEROUS tests, I discovered the problem is down to a FAULTY ETHERNET CABLE, which I did not use for my Mac -> cable modem direct connection. This was why I was able to get gigabit ethernet speed with a direct connection but not through time capsule!
I replaced the faulty cable with a new cat-6 ethernet cable and voila! problem solved!
So here're the test results (using an more up-to-date speed test) before and after I replaced the faulty lan cable:-
(while I'm at it, I've also thrown in some additional results demoing the wired and wireless throughput of the 4th gen Time Capsule)
Faulty cable through Time Capsule:-
New ethernet cable direct connection:-
Wired connection through Time Capsule:-
Wireless Connection (wireless-n 5GHz three streem 450Mbps transmit rate) through Time Capsule:-
I'm a bit surprised that a damaged cable resulted in a lower link speed rather than no connection at all.
Also, while the throughput of Time Capsule can't really match the link speed of the direct connection, I'd say it's not shabby at all.
Thanks again LaPastenague for your solutions.

Which sfp module add in Sg300-10 for connecting with 4503 switch over fiber?

Hello guys...
i need help in network design...
i have 2 cisco 4503 core switches with 48 port sfp that will use to connect at branches SG300-10 with 2 fiber that is single mode...
which module should use in Sg300-10 that will compatable with 4503 fiber module?
Please tell me if I will use the GLC-LH-SMD for WS-C4500 with fiber optic card WS-X4448-GB-SFP what type of SFP do we have to use for the small business switch SG300-10?
We could go for MGBLX1?
if i am ok please reply if not please provide the correct one solution for my design...!

Hello guys...
i need help in network design...
i have 2 cisco 4503 core switches with 48 port sfp that will use to connect at branches SG300-10 with 2 fiber that is single mode...
which module should use in Sg300-10 that will compatable with 4503 fiber module?
Please tell me if I will use the GLC-LH-SMD for WS-C4500 with fiber optic card WS-X4448-GB-SFP what type of SFP do we have to use for the small business switch SG300-10?
We could go for MGBLX1?
if i am ok please reply if not please provide the correct one solution for my design...!

PS3 error: "An Ethernet cable is not connected" with E2000

Problem: My PS3 displays An Ethernet cable is not connected almost immediately after logging in. I am connected through a Linksys E2000 router. If I reset the cable modem, it will work for 10-15 minutes until it errors out again. If I plug the PS3 directly into the cable modem, it works fine. I'm really confused.
1. I do not believe it is the router, as my computer is also connected to the router, and works fine. My Touchpad is connected wirelessly and also works fine.
2. I do not believe it is the PS3, because it works fine if I plug it directly into the cable modem. I tried switching to wireless and it finds a lot of other signals (including mine), but I have the same problem if I choose wireless.
I first had this problem with a launch PS3 and a Netgear router after almost three years of no problems. This was back in November 2010. I replaced it with a Linksys E2000 router in January 2011, and a slim PS3 in late September 2011.
I had no problems from January until last weekend. I have tried to do the DMZ trick, but no luck. I have also tried to set the primary and secondary DNS to 4.2.2.1.
Does anyone have any insight? If I need to buy a new router, I will, but I don't understand because it works for my computer and Touchpad. Is it something crazy like when November comes, my internet settings get corrupted?

Try using the DHCP reservation feature to give your PS3 a "static " ip outside of the DHCP server range. So something above the range called "IP Address Range". 192.168.1.150 should be good, but you can check to confirm that this address isn't in that range.
Make sure your PS3 is set to obtain the network information automatically, NOT through a custom setting. Also, make sure your PS3 is turned off completely before doing this.
Could you also give us a screenshot of the "signals" tab when you go to 192.168.100.1?
I don't work for Cisco. I'm just here to help.

ThermoVision Labview Digital Toolkit for connection with a FLIR SC645 is not working

Can somebody help me?
I have troubles connecting my FLIR SC 645 with my Labview Software.
The “FLIR R&D Software” works fine I can make a connection with the camera over Ethernet, I can take images and read temperatures.
Now I want to use the labview toolkit to automate the measurement in a production process.
So the camera is connected over a Ethernet port directly to the PC.
I can see the camera in NI MAX under NI-IMAQdx Devices. If I try to snap a image a error occurs:
Error 0xBFF69031 The system did not receive a test pack from the camera.
The package may be to long or a firewall may be enabled.
When I dig in the libraries of ThermoVIsion I found the “ThermoVision Cam Ctrl.vit”. This program does work, it connects to the camera and I can do a internal calibration and some focusing but that is it. The examples from Thermovision does give me a black image and a Error -1.
Does anyone has some experience with this toolkit?
The main idée I had is to inport the image into a vision builder and their work with some intensity levels. Is this possible? And how do I connect with the camera?
Hendrikx Danny

Hello,
usually IR cameras have dfferent pallete displays (monochrome, rainbow, saturation, etc...). The default is probably monochrome, that is why you are seeing it. You should be able to change the output by sending the appropriate command to the camera.
Regarding the jumbo frames (I suggest that you leave this alone, if you get your camera working):
let me google it for you
Best regards,
K
https://decibel.ni.com/content/blogs/kl3m3n
"Kudos: Users may give one another Kudos on the forums for posts that they found particularly helpful or insightful."

Changing material type for material with history

We needed to change the material type for an existing item with purchasing, inventory and sales history from HAWA to UNBW. We are trying to PGI the first receipt since the change, and are receiving an Account Determination error .
When I look at the material master set-up, I still see records in the MBEW table. UNBW items that are set-up that way from scratch do not have any records in this table. Is this what is driving my error?
I'm guessing that if it is not, there will be some discrepancy between the material, vendor, and capital asset order.
Any insight is appreciated.

even UNBW can have accounting views.
The problem is probably that you just changed the material type and did not change the valuation class in the accounting view accordingly. remove it, and try again.

Cable Advice for connection to HDTV

I am waiting for delivery of a Pioneer LX5090 and a new MBP but I am confused as to the type of cable required to connect these two up.

For the video, you need a mini-DisplayPort to HDMI adapter like THIS ONE from monoprice.com, and an HDMI cable.
For the audio, you need a mini-stereo to RCA cable like THIS ONE from amazon.com (these are commonly available). The TV you list does not seem to have digital audio input (though it does have digital audio output).

Object type for connection object

Can any one tell me the object type for the connection object.
Regards, Goksi

hi goksy
go to swo1
click push butt BUSINESS OBJECT REPOSITORY
and click all types in the pop up screen
then u need to xpand the sap util node
then u will find all the isu objects involved
hope it will be useful to u
kr
raj

Cable needed for connection?

Quick question - what cable do I need for the apple tv for a Visio HD TV?

captfred wrote:
HDMI works as well as "composite" video.
appletv does not support composite at all.
i'm sure you meant component.

Adobe Community Help search box is black. Can't see what I type for inquiry.

When I click on help in Photoshop or Bridge
CS5 the Community Help search box appears, but the entire left column is black. I can't see what I type or see any results, although they're there (I can click at random in that black column and I get some result on the right). Anyone know how to fix that?

I uninstalled Air and Flash, then downloaded and reinstalled each of them.
Clicking on Help in Bridge now results is black backgrounds on the top row (left and right), and when I type in a search term it appears in white. However, I get no results from my inquiry (I typed in "photo", among others). Anything else I could try? Help was never very helpful, but at least it was someplace to start....

What cable type for connecting with gigabit port

Similar Messages

Maybe you are looking for