What cables are needed to extend the range of my airport extreme with my time capsule

I just purchased a new Time Capsule, and I want to install it and use my current Airport Extreme to extend our home's wireless network. What extra cables are needed, and is there a diagram for this setup? We currently have a broadband network.

Apple's instructions to do this are here:
http://support.apple.com/kb/HT4260
You will need an Ethernet cable to connect your new Time Capsule to the AirPort Extreme.

Similar Messages

Can i extend the range of an airport extreme with another airport extreme and use the ports on the airport extreme i used to extend the network?

That seems like a complicated question.
I have a Time Capsule (which the HD *****, but that is matter for another discussion) and want to extend the range with an Airport Extreme because I have 2 devices in one room that do not do wireless but have Ethernet ports.
The room has iffy WiFy connectivity too.
I want to know if the 3 ports on the Airport Extreme still work after configuring it as an extender rather than a router.

The thing is that I want to know if I can put the Airport Extreme at the edge of the room where the existing Base does not reach.
This will not work.
Remember, an "extending" AirPort can only extend the quality of wireless signal that it receives. For that reason, it must be located where it can receive a strong wireless signal in order to work effectively.
For example, let's say that your "main" router was on one end of the house and you want to extend the signal to reach the other end of the house. In this case, you would locate the "extending" AirPort about half way between the main router and the other side of the house.

Can I extend the range of my Airport Extreme with 2 Airport Express units?

I am using Airport Extreme as my basic router. I have connected 2 airport express units (all new since 12/09) to extend the network about 300 ft into another building to a PC. I am receiving about 65% signal and only one of the express units is extending the signal. Previously I was able to extend the network with a Netgear router and one D-Link extender and achieved 85%.
I would like to use the 2nd express to extend the signal of the 1st express which is extending the Extreme.
If this is not possible, can I use something other than an express with the extreme to extend the wireless network?

Here are the basic steps in setting up a static WDS. Please compare them to what you have done to see if there are any differences. Hopefully, this will give you a clue on what to try.
AEBSn - WDS Setup
(Note: To facilitate the WDS set up, place the base stations within near proximity of each other during the set up phase, and then relocate them to their desired locations when complete. Also, jot down the AirPort IDs (MAC addresses) for each of the base stations to be used in the WDS. The AirPort ID and is printed on the label on the bottom/side of the base station.)
Main Base Station Setup
o Click the AirPort status menu in the menu bar and choose the wireless network created by the base station you want to set up as the main base station.
o Open AirPort Utility (located in the Utilities folder in the Applications folder on a Macintosh computer, or in Start > All Programs > AirPort on a computer using Windows).
o Select the main base station, and choose Manual Setup from the Base
Station menu, or double-click the base station to open the configuration in a separate window.
o Enter the base station password if necessary. If the base station is using the
default password of public, you will not be prompted for a password.
o Click Wireless in the toolbar, and then choose “Participate in a WDS network” from the Wireless Mode pop-up menu.
o Click WDS and then choose “WDS main” from the WDS Mode pop-up menu.
o Select the “Allow wireless clients” checkbox if you want client computer to connect to this base station.
o Click the Add "+" button and enter the AirPort ID of the base station you want to connect to this base station.
o Click Update to send the new settings to the base stations in the WDS.
Remote Base Station Setup
o Click the AirPort status menu in the menu bar and choose the wireless network created by the base station you want to set up as a remote base station.
o Open AirPort Utility (in the Utilities folder in the Applications folder on a Macintosh computer, or in Start > All Programs > AirPort on a computer using Windows).
o Select the remote base station, and choose Manual Setup from the Base Station menu.
o Enter the base station password, if necessary. If the base station is using the default password of public, you will not be prompted for a password.
o Enter the same network password as the main base station, if necessary.
o Click AirPort in the toolbar and click Wireless. Choose “Participate in a WDS network” from the Wireless Mode pop-up menu, and choose the same channel as the main base station from the Channel pop-up menu.
o Click WDS and choose “WDS remote” from the pop-up menu.
o Enter the AirPort ID of the main base station in the WDS Main field.
o Click Update to transfer the settings to the base station.
Relay Base Station Setup
o Click the AirPort status menu in the menu bar to join the wireless network created by the base station you want to set up as the relay base station.
o Open AirPort Utility (in the Utilities folder in the Applications folder on a Macintosh computer, or in Start > All Programs > AirPort on a computer using Windows).
o Select the relay base station, and choose Manual Setup from the Base Station menu.
o If the base station is using the default password of public, you will not be prompted for a password.
o Enter the same network password as the main base station, if necessary.
o Click AirPort in the toolbar and click Wireless. Choose “Participate in a WDS network” from the Wireless Mode pop-up menu, and choose the same channel as the main base station from the Channel pop-up menu.
o Click WDS and choose “WDS relay” from the WDS Mode pop-up menu.
o Enter the AirPort ID of the main base station in the Main AirPort ID field.
o Click the Add "+" button and enter the AirPort ID of the remote base station this relay base station will connect to.
o Click Update to transfer the new WDS settings to the relay and remote base stations.
(ref: Pages 42-46 of "Designing AirPort Networks.)

I'm trying to extend the range of an Airport Extreme 802.11g by adding an Airport Express 802.11n. I set the Express up to join the existing network, but it does not make any difference in the range of the network. What's wrong?

I'm trying to extend the range of an Airport Extreme 802.11g by adding an Airport Express 802.11n. I set the Express up to join the existing network, but it does not make any difference in the range of the network. What's wrong?

Let me see if I can help you with the basic WDS configuration steps:
Note: To help facilitate the setup, temporarily connect the AXn directly to the AEBS LAN port using an Ethernet cable. Once the setup is complete, you can move the AXn to the desired location. For all configuration steps you will be using the AirPort Utility. Before starting, be sure to jot down the AppleIDs for both base stations.
802.11g AirPort Extreme Base Station (AEBS) Configuration
AirPort Utility > Select the AEBS > Manual Setup > Wireless tab
Wireless Mode: Participate in a WDS network
Manual Setup > WDS tab
WDS Mode: WDS main
Allow wireless clients (checked)
WDS Remotes: <enter the AppleID for the AXn here>
Click on Update and allow the base station to restart.
802.11n AirPort Express Base Station (AXn) Configuration
AirPort Utility > Select the AXn > Manual Setup > Wireless tab
Wireless Mode: Participate in a WDS network (Note: You may have to hold down the Option (Mac) or Control (PC) key to see this option in the list.)
Manual Setup > WDS tab
WDS Mode: WDS remote
Allow wireless clients (checked)
WDS Main: <enter the AppleID for the AEBS here>
Click on Update and allow the base station to restart.

External antenna to extend the range of an Airport Extreme 802.11g

What is the best external antenna for extending the range of my Airport Extreme? My studio is in an old metal building and I want to send the single to my house which is about 50' away. The metal blocks the signal so I believe I need some kind of directional antenna. Any advise?

Here are a few you can check out ...
o Dr. Bott's ExtendAIR Direct Antenna
o QuickerTek 27dBm Transceiver

How to extend the range of my Airport Extreme network by adding an Airport Express

How to extend the range of my Airport Extreme network by adding an Airport Express?

You have to make sure that the AirPort Express is in Factory Default Settings. If it is straight out of the box, it is ready to be configured.
The instructions that I will provide are for using AirPort Utility 6.0, which you have.
Locate the Express in the same room as the AirPort Extreme for the configuration. Power it up and allow a full minute for the Express to display a blinking amber light.
Make sure that the wireless is turned on your Mac
Open AirPort Utility 6.0 and look at the small rectangle in the upper left hand corner of the display. It should now read something like "Other AirPort Base Stations (1)"
Click on the rectangle, and then click on the AirPort Express xxxxxx listing
AirPort Utility will take a minute or two to analyze the settings on your network and then suggest that the Express be configured to "Extend" your wireless network.
Edit the Base Station name to your liking, then click Next in the lower right hand corner
Allow a full minute or two let AirPort Utility do its work
When you see Setup Complete, click Done at the lower right of the window.
Now move the AirPort Express to a location that is approximately half way between the AirPort Extreme and the area that needs more wireless coverage.
You should be in business.

What is the best way to hookup my airport extreme with my time capsule ?

what is the best way to hookup my airport extreme with my time capsule ?

It sounds like you have the AirPort Extreme configured as the "main" router on your network.
If that is the case, connect an Ethernet cable from one of the LAN <-> ports on the AirPort Extreme to the WAN "O" port on the Time Capsule
Power up the Time Capsule
Connect another spare Ethernet cable from your Mac to one of the LAN <-> ports on the Time Capsule
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click on the Time Capsule, then click Manual Setup
Click the Wireless tab below the row of icons and make sure that the setting for Wireless Mode = Off
Click the Internet icon, the click the Internet tab
Insure that the setting for Connect Using = Ethernet
Insure that the setting for Connection Sharing = Off (Bridge Mode)
Click the Update button at the lower right of the window and wait a full minute for the Time Capsule to restart
Then power cycle the entire network by powering everything off....order of power down does not matter
Wait a minute
Power up the modem first, and let it run a few minutes by itself
Power up the AirPort Extreme next and let it run a full minute
Power up the Time Capsule next and let it run a full minute
Keep starting devices one at a time about a minute apart until the entire network is back up
You will need to reset the backup path from your Mac to the Time Capsule to get backups going again
Open System Preference (gear icon on the dock)
Open Time Machine
Click Select Disk
Click the Time Capsule to highlight it
Click Use for Backups or Use Disk and backups should begin again in a few minutes
If you do not want to leave the Mac connected to the Time Capsule by Ethernet, remove the Ethernet cable from the Mac to the Time Capsule, then log on to the AirPort Extreme wireless network

Is it possible to extend the range of one airport express with a second airport express?

Hi,
We have a Time Warner router and have it hardwired to an Airport Express. Is it possible to extend the range of that one airport express with a second airport express?

... The new AirPort Express that I have is an 802.11n version, but the second one is an older model and I don't know which version it might be. Also, the system recently updated so I'm using the AirPort Utility 6.1.
If you are using Mountain Lion, AirPort Utility 6.1 is the version installed by default. It will not be able to administer "older" AirPort base stations.
For them, use AirPort Utility 5.6 which contains the features you need. It can administer your older Express as well as current production base stations.
AU 5.6 is compatible with Lion as well as Mountain Lion, however, the installer app will refuse to install it on Mountain Lion.
This dilemma is easily solved though. You simply need to extract the app from the installer package using a package extractor like Pacifist.
Download Pacifist here: http://www.charlessoft.com/
Download AirPort Utility 5.6 here: http://support.apple.com/kb/DL1482
If you happen to have an archived copy of the AU 5.6 app somewhere, such as a Time Machine backup or equivalent, you can simply restore it or drag the app to your Mountain Lion system's Utilities folder. It will run without complaint. It is only the package installer that is the problem.
Mountain Lion will not allow you to delete its existing version of AirPort Utility. Just ignore it. It and the older version (which will bear the unique name "AirPort Utility 5.6") can peacefully coexist.
Note: For those with Leopard or Snow Leopard systems you need AirPort Utility 5.6.1 (this is confusing - a later AirPort Utility version for an earlier OS X version - but it is correct).
Download AirPort Utility 5.6.1 here: http://support.apple.com/kb/DL1536

I have an old airport that still works, can you use it the same way that one uses an airport express to extend the range of an airport extreme base station?

It would save me a few bucks if I could use an old airport that I have to extend the range of a new airport extreme. My concept would simply be to use the old Airport the same way I would use a newer Airport Express as a slave repeater. Is this doable?

Both the new AirPort Extreme and older AirPort Express will have to be configured using Apple's WDS settings to provide more wireless coverage.
Here are the downsides:
WDS operates only at "g" wireless speeds, so you will lose all of the faster "n" wireless capability of the new AirPort Extreme
WDS cuts the bandwidth on the entire network in half, so you will have a "g" wireless network running at half speed.
WDS is difficult for most users to configure because it is easy to make a mistake and hard to recover without starting all over again
Bottom line......Saving a few bucks will be very costly in terms of performance on your network.

Help! Im trying to extend the network on my Airport Extreme with an Express

This is probably such a begginers question but it has truely boggled my mind for the last 24 Hours!
I have brought an airport express to extend my airport extreme network. My Airport extreme is the base and is hooked up to my initial Home model from my ISP which works fine.
I have been trying to connect my airport express and am having no luck. I have plugged the airport in but am having no luck locating it on my airport utility (only my actual Airport Extreme shows)
Can someone please help me Ive been here for hours reading on forums trying to sort this out and Im gettin nowhere fast!
The light on the express is flashing orange. I have tried to reset it but there still is nothing showing.
any ideal on what i could do or follow step by step?

Ok, the question is how can i extend the range with
my airport extreme base,
With an Airport Express or another Airport Extreme
I have A netgear WNP802, it
has a repeating feature.
Which won't work with your Airport Extreme
< But i am wanting to have the
netgear and the apple airport extreme talk to each
other so that i can put the net gear in a seperate
room to extend the range of signal. </div>
This is not possible.
How can i do this?
You can't.
Netgear and Apple use different chips which means they won't and can't talk to each other when it comes to extending networks.

Using an Airport Express to extend the range of my Airport Extreme.

i've just bought an Airport Extreme and an Airport Express so i can connect my MacBook in my bedroom (second floor) to the DSL modem in the basement.
i was able to configure the Extreme as a base station but cannot figure out how to configure the Express to use as a relay.
no matter what i do, i cannot get the Express to show up in the Airport Utility, even when i have it powered in right beside the Extreme base station in the basement.
please help!

I have found that you need to have an Ethernet cord connecting the Airport Express to your Mac to set up the Express to work on WDS with your Extreme. Once it is set up, you should be able to see both the Extreme and the Express wirelessly, but for setup you need the wire to the Express.

Using an Airport Extreme and a Time Capsule at the same time

Guys I have had an Airport Extreme and a Time Capsule running together for nearly a year now and over the last few days the TC has been behaving badly. I changed its settings and now I'm in a mess. No, I can't remember the previous settings
Does anyone have a definitive list of the settings I need please? I have an ethernet cable modem, and the Airport Extreme is plugged into that as the main router. Two computers and the Time Capsule are plugged into the Airport Extreme using ethernet. The Time Capsule at the moment is just used as a network drive for Time Machine, but at some point I want to move it, with a long ethernet cable, and use it for extending the wifi in the house.
1. Should I connect the TC using its WAN port or one of the other ethernet ports? At present it's one of the other ones.
2. What TC settings should I use to have it function purely as a hard drive? At the moment there's some kind of conflict and my internet connection drops every 30 minutes.
3. Then later, what settings will I need to get the ethernet connected TC to extend the range of my wifi?
I read the Apple doc about WDS and tried setting the TC up that way. Then I discovered there is no WDS option in the AE Wireless settings. Only "Create a wireless network" or "extend a wireless network". The same setting on the TC has these options: "Create a wireless network" "Participate in a WDS network" or "extend a wireless network". Both devices have firmware 7.5.2. It didn't work with only the TC set for WDS, of course, but after that I can't get it back the way it was - which wasn't reliable anyway
Any help in exactly what the Wireless and Internet settings should be would be massively useful. Thanks!

If you use the extreme as a router then the tc should be connected via its wan port to one of the lan ports on the extreme. Tc should be set up in bridge mode. Basically you could set it up to create another wireless network beside the one created by the extreme. There is no need to use WDS or extend the other network.
Use the same SSID and password for both machines. Computers will connect to the strongest signal.

If I have an airport extreme and a time capsule is it possible for seamless switching between the 2 when a signal is weak or drops Main reason is as I move from my first floor to my attic office and would like to place one (airport extreme)downstairs and

If I have an airport extreme and a time capsule is it possible for seamless switching between the 2 when a signal is weak or drops
Main reason is as I move from my first floor to my attic office and would like to place one (airport extreme)downstairs and time capsule upstairs to get complete coverage

In theory, yes. If you configure the two base station into either an extended or roaming network configuration, you should be able to walk a laptop between routers and the laptop should attempt to connect/reconnect to the base station providing the stronger signal ... but, in reality, this is not always 100% true.

HT4259 I am trying to connect airport express to extend the range of my airport tower. What type of cords do I need to connect the airport express to a hardwired outlet in the wall of a bedroom?

I am trying to connect my airport express to extend the range of my network to a bedroom that is hard wired for internet. What type of cord/cords do I need to do that?

You can connect the AirPort Express to the wall port in the bedroom for the setup.....but first....if you have not already done so.....it would be a great idea to make sure that the connection in the bedroom is working correctly.
To do that, turn off the wireless on a laptop and connect the laptop directly to the wall port in the bedroom using an Ethernet cable. Make sure that the laptop can get a good Internet connection that way. If it can, this tells you that the cabling is working correctly, so the Express will work well when you connect it up.
If you don't have a laptop with an Ethernet port, then we'll have to assume that the folks that pulled the cables and installed the jacks tested things as part of the installation.
When you are ready to install the Express, you can use an iPhone or iPad if you have one handy for the setup.

How do I add an Airport Express to extend the range of my WIFI network with my iMac as a base station?

Hi people
I need help to configure a new Airport Express only to extend the range of my WIFI network.
My ethernet cable from modem is connected directly in my iMac and I am sharing the internet by WIFI inside home very fine.
Now, I would like connect my devices on my garden on backyard.
I can't move my iMac from their place and i just want add a Airport Express between the iMac and backyard to extend the range of WIFI.
But I can't to configure to that. On Airport Utility appear the Airport Express connected directly to internet globe, but don't work.
So, what can I do? What is wrong?
Thanks all and best regards.
Carlos Sgrillo, from Brazil.

The AirPort cannot do what you ask.
The Airport needs to connect to a modem, or another router......not to a computer.
The Express can only extend a wireless signal that has been provided by another Apple router.

What cables are needed to extend the range of my airport extreme with my time capsule

Similar Messages

Maybe you are looking for