What causes the grey screen with retart statement??

Hello All-
This has happened 4x in the last couple days...While on the internet, I attempt to go to another site, and suddenly with no warning a grey screen slowly scrolls down the displyy with a dialog box telling me I must restart. Does anyone know what this is about? I ran Hardware Diagnostic, no problems...I ran Utility Disk, no problems. Then I ran Norton Doctor, it found a major problem on HD which it fixed. After completing all this, the problem happened again while trying to access pgatour.com!
Thanks-
Dominic

What you are experiencing is called a Kernel Panic.
This is a good article which has some steps you can take to troubleshoot the Kernel Panic.
http://www.thexlab.com/faqs/kernelpanics.html
Then I ran Norton Doctor, it found a major problem on HD which it fixed.
Oh, dear. This is not good. Norton Disk Doctor causes more problems for OS X than it actually fixes. It's basically a cancer to Mac OS X. I would remove it as soon as you possibly can. I would go so far as to say it may even be one of the causes of your Kernel Panics.
There was probably nothing wrong with your hard drive in the first place.
If you search through the forums, you'll see that MANY people have been burned by Norton Utilities, Norton Systemworks, and especially Norton Disk Doctor.
Those products have been discontinued by Symantec as a result of all of the reported issues with Mac OS X compatibilty.

Similar Messages

  • I have a Macbook and I left it unplugged. It started up slowly when I plugged it in again, but it seemed fine. Once it started charging I shut it down so it would be easier, but now it will not go past the grey screen with the apple. What do I do?

    I have a Macbook and I left it unplugged. It started up slowly when I plugged it in again, but it seemed fine. Once it started charging I shut it down so it would be easier, but now it will not go past the grey screen with the apple. What do I do?
    I have Snow leopard on my computer, and I tried to do a hard restart as an article suggested, but it did not work. I also tried cleaning out the PRAM.
    The only things I did last night:
    -cleaned the history of Firefox out, including cookies
    -let it unplugged all night
    -plugged it back in the morning, it took a long time to figure itself out, but eventually the time was correct and I got on the internet for a bit
    -shutdown the computer since I was going out and thought it would help the computer charge
    -came back, tried to turn it on, and found that it would not go past the grey screen the apple on it and the spinning wheel even though I left it for 20 minutes or more
    -tried turning it off and on to no avail

    Before doing a reinstall, which may not be needed at this point,
    Try using Disk Utility to do a Disk Repair, as shown in this link, while booted up on your install disk.
    You could have some directory corruption. Let us know what errors Disk Repair reports and if DU was able to repair them. This could just be a start in repairs and you may need a better utility to finish the job.
    Then Repair Permissions.
    No need to report any Permissions errors........we all get them.
       DALE

  • My Macbook aliminium unibody from late 2008 will not boot. I reach the grey screen with the apple icon and the spinning grey gear. I used disk utility to boot it but it said integrity test failed. I don't know what to do can anyone please help?

    My Macbook aliminium unibody from late 2008 will not boot. I reach the grey screen with the apple icon and the spinning grey gear. I used disk utility to boot it but it said integrity test failed. I don't know what to do can anyone please help?

    Sounds like you may have a harddrive issue.  You are probably going to need to get that changed out and then install the OS X again to get it going.

  • My macbook pro will not boot. It gets the grey screen with the apple until the bar is half way across and then shuts down. The only screen I can get to is in safe mode and I don't know what to do with that

    my macbook pro will not boot. It gets the grey screen with the apple until the bar is half way across and then shuts down. The only screen I can get to is in safe mode and I don't know what to do with that

    Mac OS X: Gray screen appears during startup - Apple Support

  • I was installing the new EFI software update on my macbook pro and I became stuck on the grey screen with the window that said "installing 2 items", its been on the same screen for 2 1/2 hours. does anyone know what I can do?

    As the title says.
    I was installing the new EFI software update on my macbook pro and I became stuck on the grey screen with the window that said "installing 2 items", its been on the same screen for 2 1/2 hours. does anyone know what I can do?
    I don't want to restart it because im scared that something might go wrong.
    operating lion

    LimitLess- wrote:
    Hi,
    I had the power supply connected when I attempted it previously but even so my problem occurred. My rom is different and so I still need to update it.
    Thanks
    I wanted to mark your answer helpful too but I didn't know that I could only put it for 2 answers. Sorry
    That was good advice by G-N and s/he is correct about it. Unfortunately, ASC allows only 2 "helpful" and 1 "correct" marks per thread.

  • My MacBook pro will not load past the grey screen with the spinning wheel. What do I do?

    My MacBook will not load past the grey screen with the spinning wheel of death. Anyone have any solutions?

    Invoke Safe Mode by holding down the shift Key as you restart. This will do a Disk Utility "Repair Disk" as it starts up (so it takes a few minutes longer) and then load with minimal extensions loaded, and request your login username and password, even if you normally do not use them to log in.
    Safe Mode runs the screen using simple, unaccelerated commands. Most things are available in Safe Mode, but things that rely on extensions will not be.
    Acomputer that works in Safe Mode, but fails again after you restart, often implicates your extensions and add-ons.

  • Hello my Mac Air is frozen on the grey screen (with the apple symbol, sleeping mode, restart-and off button), once you turn it on.

    hello my Mac Air is frozen on the grey screen (with the apple symbol, sleeping mode, restart-and off button), once you turn it on. I Can`t press any button.My Mouse still works. Battery is charged. Alt-cmd-escape doesn`t work It even after a forced shutting off, the problem is the same.   what should i do? Thank you for your help.

    Take each of these steps that you haven't already tried. Stop when the problem is resolved.
    Step 1
    The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.   
    There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
         a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
    b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
    c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
    Step 2
    Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
    If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
    Step 3
    Boot in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
    Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
    The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 5.
    If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
    If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
    Step 4
    Sometimes a boot failure can be resolved by resetting the NVRAM.
    Step 5
    Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
    This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
    Step 6
    Reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
    Step 7
    Repeat step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a Time Machine or other backup.
    Step 8
    This step applies only to older Macs (not current models) that have a logic-board ("PRAM") battery. The battery is distinct from the main battery of a portable. A dead logic-board battery can cause a gray screen at boot. Typically the boot failure will be preceded by loss of the startup disk and system clock settings. See the user manual for replacement instructions.
    Step 9
    If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested.

  • I installed snow leopard which I now realise that it was the wrong one because it came out before my laptop and now it won't changed from the grey screen with the apple on it how do I fix it ???

    I installed snow leopard which I now realise that it was the wrong one because it came out before my laptop and now it won't changed from the grey screen with the apple on it how do I fix it ???

    MacBook Pro
    Apple - Support - MacBook Pro
    Mac OS Version builds
    When did yours come out? what does the above show as model and minimum build?
    You should have yoru OEM OS X DVD, not one from another Mac, or retail, though the last retail OS X DVD was a year ago 10.6.3.
    If it installed, I don't see an issue unless the drive had corrupt directory etc.
    What you need to do is repair your boot drive or restore from backup.

  • My Imac will not move beyond the Grey Screen with the spirl spinning any ideas

    Recently I rebooted my IMac, it now will not move past the grey screen with the spinning spirl.
    Please help

    Turn off your machine, then power on whilst holding down cmd+alt+p+r until the screen goes off and you hear the chime again.
    Also, what iMac do you have/how old?

  • How to get passed the grey screen with apple logo when turning on?

    I got a Imac Intel 20" about 6 years old. The other day turned it on and everscince havent been able to get passed the grey screen with the apple logo on it? What could be the problems and how can i fix this?
    cheers

    Hello v:
    The computer is fairly old and anything can happen.  You could try resetting the SMC and see if that helps.
    Barry

  • TS2570 On start up of my new iMac it locks on the grey screen with the apple logo and the progress wheel spins. Boot up in safe and this is where it stopped at "BootCacheControl: Unable to open /var/db/bootcache.playlist: 2 no such file or directory. "

    On start up of my new iMac it locks on the grey screen with the apple logo and the progress wheel spins. Boot up in safe and this is where it stopped at "BootCacheControl: Unable to open /var/db/bootcache.playlist: 2 no such file or directory. "

    Reinstalling MacOS does NOT fix the problem for me.  I'm still searching a solution !
    Bernard

  • Im having trouble getting my macbook pro to boot up after a fail safe boot, im getting as far as the grey screen with the apple loggo. so im trying to run a disk repair but is saying the disk is locked, how do i unlock disk??

    Im having trouble getting my macbook pro to boot up after a fail safe boot, im getting as far as the grey screen with the apple loggo. so im trying to run a disk repair but is saying the disk is locked, how do i unlock disk??

    Some clarification may help.
    You say you cannot boot normally.  It shows a gray screen with the Apple logo.
    Did you say it will boot successfully in Safe Mode (boot, then hold down the Shift key)?
    How did you boot the machine to run Disk Utility?  (Which keyboard combinations)?

  • My macbook pro doesn't bootbeyond the grey screen with apple icon and spinning wheel.

    My macbook pro doesn't boot beyond the grey screen with apple icon and spinning wheel.  I used the "Option" button to access the Disk Utility function and run Repair Disk and Repair Disk Permissions.  Should I restart my computer?

    The following support article is somewhat outdated. Where it refers to booting from an installation disc, you should boot from your recovery partition (if running 10.7 or later) by holding down the key combination command-R at the chime.
    Mac OS X: Gray screen appears during startup

  • I didn't close my mac air down properly and when i tried to use it, the screen was frozen.  I turned it off and restarted it, and the grey screen with the apple logo appear and the circle just keeps spinning.  Can you advise?

    i didn't close my mac air down properly and when i tried to use it, the screen was frozen.  I turned it off and restarted it, and the grey screen with the apple logo appear and the circle just keeps spinning.  Can you advise?

    Try resetting the SMC
    Intel-based Macs: Resetting the System Management Controller (SMC)

  • When my Mac battery dies and I turn it back on, it always crashes on the grey screen with the progress bar, then it restarts (taking forever) and does not remember any of the programs I was running. MacBook Pro 13 inch running Mavericks

    When my Mac battery dies and I turn it back on, it always crashes on the grey screen with the progress bar, then it restarts (taking forever) and does not remember any of the programs I was running. MacBook Pro 13 inch running Mavericks

    http://osxdaily.com/2014/10/17/os-x-yosemite-installation-stuck/
    also use the Command-L to view logs during installation

Maybe you are looking for

  • Profit Center Changing Problems

    Hi, I want to give the profit center though it was not assigned at the time creation of material master.So if i want to give the profit center in MM02 it is showing the error "the Stock is already available". So please help me out.if there is any pro

  • Smartforms output in HTML format

    Hi Experts, I want to save my smartforms in HTML format.Is there any Standard programe is available for it. Like as RSTXPDFT4 for converting output in PDF format.

  • Payment term in customer master

    Gurus, XD02 - Change Customer Master Payment term is maintained in => Company code data -> Payment Transactions -> Payment Data-> Payment term => Sales Area Data -> Billing Documents-> Delivery ad payment terms-> Terms of payment In sales order, syst

  • Applescript to open various files and add info from filename to the file

    Hi guys, first time using this forum... and first time trying to do a script for apple... I figured out how to do simple things... like open files and stuff to text files...  but don't know where to begin: I have a directory datalogs... within the di

  • Oracle EBS R12 DR - Status Column Shows N in FND_NODES

    Hi, We implemented DR for Oracle EBS R12 (2-Node Oracle 10gRAC, 2-Node Apps) using Oracle Data Guard. During the Failover testing we noticed that the Status shows N for the DB Nodes and First Apps Node. It shows Y only for the 2nd Apps Node in the FN