What deterimes the amount of data in a waveform from a TDS 1012 scope

Hello,
   What determines the amount of data that is in a waveform that comes out of a TDS 1012 scope? I am assuming that I will have to look at the driver vi to determine the commands sent to the scope to figure it out. I am in a situation that I need to have the y axis to have a high resolution, that results in very little data being collected from the scope.
Regards,
Kaspar
Regards,
Kaspar

Hello,
    The amount of data that comes out of the TDS 1012 scope is determined by the data start (DATaTARt)  and data stop (DATaTOP)  commands that are defined on page 58 (2-38) in the  346 page programming manual for the scope. I found of that the data start was not set to 1, which is the beginning of the data.
    I also had a very low level signal on channel that was all most unreadable by the scope that caused me to think that I was not getting all of the data.
Regards,
Kaspar
Regards,
Kaspar

Similar Messages

  • What are the Non SAP data sources supported for Analysis workbooks?

    AO 1.4 SP6
    BO 4.1 SP2
    What are the Non SAP data sources supported for Analysis workbooks?
    Thanks.

    HANA is a data source (which could contain non-SAP data)
    For other Excel front-ends that may connect to "non-SAP" data look at Live Office or Power BI by Microsoft - see Excel and Power BI connectivity to SAP BusinessObjects Universes | Power BI

  • What is the purpose  of Date From and Date To In Oracle HRMS ?

    hi
    I have doubt on
    What is the purpose of Date From and Date To In Oracle HRMS?
    Thanks

    Where do you see these fields? Please give full details (eg, the navigation path).
    If you're referring to Effective Start Date and Effective End Date (effective_start_date, effective_end_date) these are two fields that appear on many HRMS entities. They're used to store dated history over time. For example:
    14-Jan-2009 to 19-Apr-2009 - Pam Stephens
    20-Apr-2009 to date - Pam Erickson
    In this example Pam got married on the 20th April 2009 and changed her surname from Stephens to Erickson. Here the history of changes are kept so that if we date-track to any time prior to the 20th April 2009 we'll see Pam Stephens and if we date-track on or after the 20th April 2009 we'll see Pam Erickson.
    Check out the following Oracle Support article for more information:
    How Date Track Works [ID 177733.1]

  • What are the features of Data Replication

    What are the features of Data Replication
    Edited by: sdmuzdba on Mar 29, 2009 10:19 AM

    You should refer to documentatin:
    [Oracle Streams Replication Administrator's Guide|http://download.oracle.com/docs/cd/B19306_01/server.102/b14228/toc.htm]
    [Oracle® Database Advanced Replication|http://download.oracle.com/docs/cd/B19306_01/server.102/b14226/toc.htm]
    If it's not enough for you, could you explain your question more briefly please?
    Kamran Agayev A. (10g OCP)
    http://kamranagayev.wordpress.com

  • Is it possible to size a flash chart based on the amount of data returned?

    My chart is based on a date range. If a user enters say a range of one year, I need the line chart to be rather large so show all the data points. Though if they select just a week, then the chart can be much smaller. I only see the hard coded values to set the size of the chart (Chart Width and Chart Height). Can those be changed on the fly based on the amount of data returned?
    Using Application Express 3.1.2.00.02 and AnyChart 3.3
    Thanks.
    Chris

    Hello Hillary,
    I tried your suggestion, but still not working for me. I added hidden text field that wold hold the vaule of the width for the chart. Then I reference that field in the chart source. Is there some other property I need to change as well? Any more suggestions? Thanks.
    Here is my source.
    <object classid="clsid:D27CDB6E-AE6D-11cf-96B8-444553540000"
         codebase="http://download.macromedia.com/pub/shockwave/cabs/flash/swflash.cab#version=6,0,0,0"
         width="&P86_NUM_ROWS."
         height="#HEIGHT#"
         id="#CHART_NAME#"
         align="">
    <param name="movie" value="#IMAGE_PREFIX#flashchart/#CHART_TYPE#.swf?XMLFile=#HOST#apex_util.flash?p=&APP_ID.:86:&APP_SESSION.:FLOW_FLASH_CHART_R#REGION_ID#">
    <param name="quality" value="high">
    <param name="allowScriptAccess" value="sameDomain">
    <param name="allowNetworking" value="all">
    <param name="scale" value="noscale">
    <param name="wmode" value="transparent">
    <param name="FlashVars" value="waiting=#FLASH_WAITING#&loading=#FLASH_LOADING#">
    <embed src="#IMAGE_PREFIX#flashchart/#CHART_TYPE#.swf?XMLFile=#HOST#apex_util.flash?p=&APP_ID.:86:&APP_SESSION.:FLOW_FLASH_CHART_R#REGION_ID#"
    quality="high"
    width="&P86_NUM_ROWS."
    height="#HEIGHT#"
    name="#CHART_NAME#"
    scale="noscale"
    align=""
    allowScriptAccess="sameDomain"
    allowNetworking="all"
    type="application/x-shockwave-flash"
    pluginspage="http://www.macromedia.com/go/getflashplayer"
    wmode="transparent"
    FlashVars="waiting=#FLASH_WAITING#&loading=#FLASH_LOADING#">
    </embed>
    </object>
    #CHART_REFRESH#

  • What is the amount of DVDs that an iMac DVD Burner can burn? (or MTBF)

    What is the amount of DVDs that an iMac DVD Burner can burn (DVD burner life time)? (or MTBF)

    Your question sounds a bit like you want to use the Superdrive professionally? Personally, I would not depend on a vertically installed, super slim Drive where any media can easily shift by 1/100th of an inch. I've noticed that mine definitely needs to "rest" and cool off after about 3 DVDs. I purchased an external burner quite a few years ago (when I had an iMac without a Superdrive) and I still prefer to use it - it is sturdy, can read all sorts of media, and is reliable whereas the SuperDrive is known to be extremely finicky especially about the media they will read or write to.
    So, I don't have a specific answer for you, but I wouldn't rely on it.

  • What is the proper way to convert a VHD from dynamic to basic without losing data?

    Hi,
    What is the proper way to convert a VHD from dynamic to basic without losing data?
    Our VM is running Windows Server 2008 R2 SP1
    Thanks in advanced

    Hi efebo,
    "After you convert a basic disk to a dynamic disk, you cannot change the dynamic volumes back to partitions. Instead, you must delete all dynamic volumes on the disk and then use the
    Convert To Basic Disk command. If you want to keep your data, you must first back it up or move it to another volume. "
    Please refer to following link:
    http://technet.microsoft.com/en-us/library/cc731274.aspx
    You can try to backup the dynamic volume via Windows Server Backup then restore it to a new basic VHD file ( the space is recommended to be   larger than or equal to the old one ) .
    Hope it helps
    Best Regards
    Elton Ji
    We
    are trying to better understand customer views on social support experience, so your participation in this
    interview project would be greatly appreciated if you have time.
    Thanks for helping make community forums a great place.

  • How to avoid the Amount and Date values for VOID Cheques

    Hi All,
    I had created a two window i.e For Amount and Date. If I process the cheque the Amount value and Date should not trigger for VOID CHEQUES.
    Can any one tel me how to avoid the Amount and Date values for VOID Cheques
    Your help will be greatly appreciated.
    Regards
    Yathish

    Hi,
    I dont know which tablel you are referring to, is it PAYR table and the field VOIDR?
    If a cheque is voided, it would have a reason and it is stored in VOIDR field of this PAYR table.
    Check if the field VOIDR is filled, if it is filled, do not print the amount and date.
    Regards
    Subramanian

  • Can you limit the amount of data accessed per user on an AirPort Extreme?

    Can you limit the amount of data accessed per user on an AirPort Extreme?

    Your question was whether the AirPort Extreme is able to establish data limits per user.
    If you add another router that has this type of capability or install software on another router, then you will be able to establish data limits for each user. The AirPort Extreme will have no control over this.

  • What is the expected release date for Adobe Media Server 5.0 and Adobe Access 4.0 ?

    What is the expected release date for Adobe Media Server 5.0 and Adobe Access 4.0 ?

    you should be on the same subnet as the server in order to receive multicast.

  • When I call nifGetObjectDictionary on a Domain Index, what is the format of data returned

    hello,
    When I call nifGetObjectDictionary on an Active Schedule Domain Index (450) of NI Card, retrieved from S-OD -> DLL Link Schedule OD Index, what is the format of data returned? I received 0801C202FFFF000000 as data and it is not matching with FF-Spec (Field Device Access Agent, page 95).
    Could you please let me know the format/structure of the data i received, so that i can parse them and understand?
    Also let me know is there any API available in NI API to upload/read Schedule Domain?
    Thanks
    Shankar.

    Sorry for replying late!
    We don't have the nifGetObjectDictionary function, so may I make a guess that you mean nifGetObjectDescription? If I'm right, there will be some trouble.
    To be honest, basically we don't support the APIs which are not included in the "NI-FBUS CM Function Reference Manual". In further, would you please let me know how you find this kind of internal functions? We cannot support it until we verify the customer has bought the complete version of APIs package and this package is still in the support period. If it matches your case, would you please help me in the verification? And then we can support the details for your question later.
    On the other hand, we don't have the APIS to upload/read Schedule Domain now.

  • The amount of data that was returned by data connection has exceeded the maximum limit that was configured by server admin

    Hi There,
    When i try to view info-path form item getting warning (This issue is not with all items but for some of them...)
    "The amount of data that was returned by data connection has exceeded the maximum limit that was configured by server admin............."
    Thanks in advance!!
    Regards
    Vikas Mishra
    Vikas Mishra

    HI Vikas,
    to resolve this do this from central admin
    Ensure to follow the below steps.
                                             i.    Open
    the central administration
                                            ii.    Go
    to General Application Settings
                                           iii.    InfoPath
    Form Services
                                          iv.    Configure
    InfoPath Form Services
                                           v.    Click
    on Data Connection Response Size
                                          vi.    By
    default it is 1500 kilobytes
                                         vii.    Change
    the Response Size in kilobytes (Increase the number).
    Kind Regards,
    John Naguib
    Senior Consultant
    John Naguib Blog
    John Naguib Twitter
    Please remember to mark this as answered if it helped you

  • What is the planed release date for 10g for Windows?

    Hi,
    10g fo HP and Sparc is already out, but windows not yet. Is it known what is the planed release date for Oracle 10g for Windows?
    TIA,
    Tamas Szecsy

    On the other hand it's just somewhat funny for me, that it looks as if marketing woudl decide which platform is released first. Some times it is Linux, some times it is Solaris and then again it is Windows. You simply can never know.

  • HT1222 Hi, what is the support end date for Quicktime 7.7.3?

    Hi, what is the support end date for Quicktime 7.7.3?

    Hi
    <b>Have you tried reading the details of the PO Releaser using the BAPIs ?</b>
    BAPI_PO_GETRELINFO
    BAPI_PO_GETITEMSREL
    BAPI_PO_GETITEMSREL            List Purchase Orders for Release (Approval): New as of 4.0A     
    BAPI_PO_GETRELINFO             Display Detailed Release (Approval) Information on Purchase Order
    BAPI_PO_RELEASE                Release Purchase Orders            
    BAPI_PO_RESET_RELEASE          Cancel Release of Purchase Orders  
    <u>Related link -></u>
    Re: How to fetch data from back end for PO?
    Hope this will help.
    Do let me know.
    Regards
    - Atul

  • What is the difference between data base objects and runtime objects

    What is the difference between data base objects and runtime objects

    Hi raja,
    data base objects means u can have the presence of these objects in the database.So the tables,searchhelps,structures,lockobjects comes under these ones.
    Runtime objects are created and destroyed after the program ends, any changes we make to them are temporary only.
    regards,
    nagaraj
    Message was edited by: nagaraj kumar nishtala

Maybe you are looking for

  • How do i uninstall new version of Elements and reinstall on external hard drive.  My PC is crashing

    How do i uninstall new software for Elements and be able to reinstall on external hard drive .Message on Wizard say I can not reinstall once I uninsall. I need to remove it from my PC. There is not enough disc space and it is crashing.

  • External hard drive will not show up on my desktop?!?!

    I have a 2 TB G-Technology G-Drive) external hard drive and when I plug it in to my macbook pro via firewire and turn it on, nothing happens. The light on the HD is on but no HD shows up on my desktop? Any help would be great! Thanks!

  • RENTED HD MOVIE NOT PLAYING

    I bought an Apple TV last week, and updated to the latest software. I rented an HD movie today with Apple TV, waited until it said "ready to view", then tried to play it. All I get is a white screen. I fast forward, and still nothing but a white scre

  • Why is my shared photo album no longer there?

    I created a shared photo stream with some friends and added about 14 pictures to it. That was yesterday and now I go to the shared tab on my photos and all my other created shared photo streams are there but not one particular one. Has this happened

  • Could not load file or assembly 'Oracle.ManagedDataAccessDTC'

    I'm a little bit stuck... I've been trying to replace System.Data.OracleClient in my application for a while now, and was very encouraged to see a managed DLL option. I have followed the quick start instructions in the readme file, but my site return