What does it mean (and how do I fix) my light is solid amber?
I plugged my Time Capsule in, but the light stays amber - what does this mean and how can I fix it?
Normally on start up, the Time Capsule should flash green for a second, then display solid amber for 15-20 seconds and then...if the settings are correct....the light will turn to green. If there is a problem at this point,the amber light will normally blink slowly.
If the light stays solid amber, this indicates that the Time Capsule has "locked up" and may have possibly experienced an internal component failure.
Power down the Time Capsule for at least 15 minutes
Hold in the reset button and keep holding the reset button in for another 10 seconds as you plug the power back in to the Time Capsule
Release the reset button and see if Time Capsule will go through the normal start up sequence
If you get a slow blinking amber light after approximately 30 seconds, you can now reconfigure the Time Capsule again using AirPort Utility
If you try the factory default reset sequence above a few times and the light remains constant amber, I'm afraid that you'll need to take the Time Capsule to an Apple store to let them have a look.
Similar Messages
-
My iPod doesn't sync it keeps coming up with the message "The iPod 'iPod Nano' cannot be synced. An unknown error occurred (13019)." What does this mean and how can I fix it?
I am getting the same error message. Have you figured it out?
-
I have downloaded music to my phone through my Apple ID and it has this message that reads you can download purchases on this device with one Apple ID account every ninety days, what does this mean and how do I fix it?
Well, it doesn't mean that at all. You can download music purchased with an Apple ID to up to 10 devices. There is no 90 day wait. The wait is if you change the Apple ID.
-
What does this mean, and how do you fix it?
"There is a problem with this Windows Installer package. A program required for this install to complete could not be run. Contact your support personnel or package vender."
Trying to install iTunes 10.7, first attempt; downloaded and ran with everything closed, seccond atttempt; just click on run, third attempt; ran upgrade with iTunes open. All of the results were the same.
Is there something wrong with the iTunes 10.7 Windows installer package?Try the following user tip:
"There is a problem with this Windows Installer package ..." error messages when installing iTunes for Windows -
My iPhoto currently has a circle with an 'x' through it and I can not open it or sync my photos.
Trying to Update my iPhoto to 9.5.1 and it says "Update Unavailable with This Apple ID" because "This update is not avaialble for this Apple ID either because it was bought by a different user or the item was refunded or cancelled."
What does this mean and how do I fix it?
I haven't changed my Apple ID or if I bought teh original update under my parents Apple ID, how do i fix it?
Thanks!What version of the OS do you have?
Is there an iPhoto application in teh applications folder?
LN -
I am trying to finalize a movie project and I get an "error in user parameter list" message. What does that mean, and how can I fix it?
what movie editing software are you using?
-
I have a Nikon D600 and D800 and I shoot everything in Raw. I use Photoshop Elements 9 for processing but I have been unable to convert any RAW files to open in PSE. Says unable to parse the file. What does this mean and how do I fix it?
Since pse 9 can only use up to camera raw 6.5 and the d600 needs at least 7.3 and the d800 needs at least 6.7, you can use the
8.6 adobe dng converter to convert those files to dng copies, which then pse 9 should open.
8.6 dng converter
windows
Adobe - Adobe Camera Raw and DNG Converter : For Windows : Adobe DNG Converter 8.6
mac
Adobe - Adobe Camera Raw and DNG Converter : For Macintosh : Adobe DNG Converter 8.6
Note:
If you have windows xp or vista or mac os x 10.6, then you'll need to use the 8.3 dng converter instead
windows
Adobe - Adobe Camera Raw and DNG Converter : For Windows : Adobe DNG Converter 8.3
mac
Adobe - Adobe Camera Raw and DNG Converter : For Macintosh : Adobe DNG Converter 8.3
how to use the dng converter
Camera Raw: How to use Adobe DNG Converter - YouTube
more info on supported cameras and camera raw plugins required
Camera Raw plug-in | Supported cameras
Camera Raw-compatible Adobe applications -
What does this mean and how do i fix this so my ipod works again on my computer and itunes: "Service 'apple mobile device' failed to start. Verify that you have sufficient privileges to start system services." I tried "retry", i tried "abort" and started over. I keep getting stuck in the same place.
Hello DEstadt,
Thanks for using Apple Support Communities.
For more information on this, take a look at:
iTunes 11.1.4 for Windows: Unable to install or open
http://support.apple.com/kb/TS5376
Check for .dll files
Go to C:\Program Files (x86)\iTunes and C:\Program Files\iTunes and look for .dll files.
If you find QTMovie.DLL, or any other .dll files, move them to the desktop.
Reboot your computer.
Note: Depending on your operating system, you may only have one of the listed paths.
Uninstall and reinstall iTunes
Uninstall iTunes and all of its related components.
Reboot your computer. If you can't uninstall a piece of Apple software, try using the Microsoft Program Install and Uninstall Utility.
Re-download and reinstall iTunes 11.1.4.
Best of luck,
Mario -
When I plug my iPod in my computer, "This iPod cannot be used because the Apple Mobile Device is not started" message pops up. What does this mean and how can I fix it?
Hello di_gitrdone,
Start with this article describing how to restart this service.
http://support.apple.com/kb/ts1567
B-rock -
I am trying to update itunes to 11.1.1.11 and keep getting message at the end ' error writing to file :c:\Config.Msi\301ded48.rbf.Verify that you have access to that directory'. What does this mean and how do I fix it?
I had this exact same problem just now, trying to upgrade to 10.7.
I even got that error msg when trying to UNINSTALL iTunes!
After hours of frustration trying everyone's different suggestions, I downloaded Revo Uninstaller http://www.cnet.com.au/apps/revo-uninstaller-10610875/ which solved the problem.
Use it to help uninstall iTunes and related software components in the following order and then restart your computer:
1. iTunes
2. QuickTime
3. Apple Software Update
4. Apple Mobile Device Support
5. Bonjour
6. Apple Application Support (iTunes 9 or later)
Then you can install iTunes from scratch.
Good luck -
I keep greeting this message trying to set up iPad mini
Apple ID could not be created because of a server error on screen after term and conditions are accepted. What does this mean and how do I fix fix it? Has anyone else had this problem?Antonio,
Show ... it worked ... you are the man! This hint of clicking the right mouse button on the prompt and run as Administrator was perfect.
Thank you very much -
When I try to sync my ipod it says it cannot be synced because "a duplicate file name was specified". What does that mean and how can I fix it??
I'd start with the following document with that one:
iPhone, iPad, iPod touch: How to restart the Apple Mobile Device Service (AMDS) on Windows -
When I try to sync my iPhone 4S with my computer, I get this message: "This iPhone cannot be used because the Apple mobile device service is not started" What does this mean, and how can I fix it?
means that apple mobile device service needs to be started try this article to get it turned back on
Restart apple mobile device service -
A file folder with a question mark Appears on my screen when turning on. What does this mean and how do I fix it?
There are four general causes of this issue:
1. The computer's PRAM no longer contains a valid startup disk setting when there aren't any problems with the disk itself. This can be checked for by pressing the Option key and seeing if the drive appears.
2. The internal drive's directory structure has become damaged. This requires usage of an alternate bootable system to perform the repair.
3. Critical system files have been deleted. This requires usage of an alternate bootable system to reinstall them.
4. The internal drive has died or become unplugged. This is the most likely case if the computer took a sharp impact or there are unusual sounds coming from the hard drive's location.
(66745) -
My macbook pro displays a folder with a question mark and won't open. What does this mean and how can I fix it?
it means your HD and the software can't find each other, the following article tells how to troubleshoot this issue:
https://support.apple.com/kb/TS1440
hopefully you have backup of your data since sometimes this means the HD is crashing.
if the article doesn't resolve the issue i would take the mac to apple store or service provider and have it looked at, the following link tells how to find one close to you:
https://locate.apple.com
good luck!!
Maybe you are looking for
-
have read the 'help' given for this question from another ipad owner --which was to download the current version and then might be able to get a compatable version --- but the new version will not download -- just tells me I have to upgrade to versio
-
What is the maximum number of fields in oracle 9 ?
Hello, My question might be very simple, but i tried to find the answer on the website of oracle and on this forum but with no success. How many fields can i put in a single oracle file ? Can i compare the fields to a column in a spreadsheet ? If so,
-
Reg: Classes and memory IDs
Hi All, I have a class which has 5 methods and around 15 attributes. DATA: lr_document TYPE REF TO zcl_ps_pricing_document, " Retrieve the Document Object lr_document = gr_runtime_context->get_document( ). in this example, lr_document is re
-
I have selected Active Standby as my preference on my N82, however I would like to be able to select different options on the list because I have no interest in either 'Share online' or 'Search Internet and my Content' Is it possible to change these?
-
Query all to display but count only certain criteria
using the following sql statement i can get all the information i want. However since i am decoding the salary_wage how do i count only those items that are over a certain dollar amount? select lss.job_order_no, jo.business_no, bs.business_