What does "Locating Timecode break" mean?
This question from a novice (but did this a few times 2 yrs. ago with no problem). I am trying to capture from a VHS tape (not a movie or from TV). What should my users prefs (on the right side anyway) be so I can just capture the clip without this timecode thing coming up? Other times -- after I have checked and unchecked various options on the R side -- it seems to be capturing but when I finally Esc nothing has been recorded. Any help would be appreciated.
In AUDIO VIDEO SETTINGS choose DEVICES CONTROL PRESET then choose NON CONTROLLABLE DEVICE.
You should also spend some time with the manual.
rh
Similar Messages
-
Error: "Locating Timecode Break"
I'm trying to capture some raw footage for a project. About 2 minutes into the capture, I get an error message saying "Locating Timecode Break". The capture stops - or almost stops - the camera keeps playing very slowly, one frame at a time. So when I finally hit the 'esc' key, I get another message saying that the 'audio sample rate of captured files does not match the sample rate of source files" (and it continues). I've restarted the computer, but the same thing keeps happening, at the same point on the (DV) tape.
I'm using the same camera, computer and software that I always do. Any ideas about what could be causing this?Please give your full system specifications, what computer, what drives, what camera or deck, how everything's connected, what settings are on the media, what settings you're using in Final Cut, and finally what version of the software, of the OS, and of QuickTime are you using
There could be two separate things here: one, there might be timecode breaks on the tape, which the capture process is trying to navigate around; and two, there is a mismatch between the audio sample rate you shot and the settings you used to capture the material. -
I can see my images in the libarary as thumbnails but when i try to edit/email some of them become Exclamation Marks in a triangle.
What does the exclamation mark mean and how to i retrieve the photoThe exclamation make is an indication that iPhoto has broken the file path to the original photo.
Make a temporary, backup copy (if you don't already have a backup copy) of the library and apply the two fixes below in order as needed:
Fix #1
Launch iPhoto with the Command+Option keys held down and rebuild the library.
Select the options identified in the screenshot.
Fix #2
Using iPhoto Library Manager to Rebuild Your iPhoto Library
Download iPhoto Library Manager and launch.
Click on the Add Library button, navigate to your Home/Pictures folder and select your iPhoto Library folder.
Now that the library is listed in the left hand pane of iPLM, click on your library and go to the File ➙ Rebuild Library menu option
In the next window name the new library and select the location you want it to be placed.
Click on the Create button.
Note: This creates a new library based on the LIbraryData.xml file in the library and will recover Events, Albums, keywords, titles and comments but not books, calendars or slideshows. The original library will be left untouched for further attempts at fixing the problem or in case the rebuilt library is not satisfactory.
OT -
TS1846 What does this error message mean?
What does this error message mean? I am trying to burn a project to DVD...
Formatting was not successful. Layer 0 exceeds the maximum layer size allowed. Please choose a suitable marker location that will support this condition.The project is 1:22:30 - 1080P HD (4.9GB)...I am using the share drop down and hitting DVD...I am using a DVD+R Dual Layer 8.5GB...It processes for about an hour and a half the status bar gets almost done and then the error message comes up...thanks for any help you can give me
-
What does Network Service Inactive mean?
What does Network Service Inactive mean?
Back up all data before proceeding.
Open the Network pane in System Preferences. A list of available network services appears on the left. If Wi-Fi is in the list, select it, then from the popup menu labeled with a gear icon at the bottom of the list, select
Make Service Active
Click Apply.
If Wi-Fi is not in the service list, click the plus-sign button at the bottom of the list, and then select Wi-Fi from the Interface menu in the sheet that drops down. Click Create, then Apply.
If there is a closed padlock icon in the lower left corner of the preference pane, click it and enter your administrator password to unlock the settings.
If the above steps don't solve the problem, continue.
Triple-click anywhere in the line below on this page to select it:
/Library/Preferences/SystemConfiguration/com.apple.airport.preferences.plist
Right-click or control-click the line and select
Services ▹ Reveal in Finder (or just Reveal)
from the contextual menu.* A folder should open with "com.apple.airport.preferences.plist" selected. Move the selected item to the Trash. You may be prompted for your administrator password. Restart the computer and recreate your settings for Wi-Fi in the Network preference pane.
*If you don't see the contextual menu item, copy the selected text to the Clipboard by pressing the key combination command-C. In the Finder, select
Go ▹ Go to Folder...
from the menu bar and paste into the box that opens by pressing command-V. You won't see what you pasted because a line break is included. Press return. -
Capturing issues-audio sample rate & locating timecode break
I am a first time FCP user.
I am working on an educational video with hours of DV source tapes.
The source tapes are from a 2R50MC Cannon mini DV camcorder also used as the deck I am capturing from via firewire. My scratch disk is Maxtor III 500GB external drive hooked up via a firewire (I'm realizing the firewire is years old could that be a problem?)
In my first capture test I captured 1 minute of tape by setting in and out points and after completeing the capture I received an error message—"The audio sample rate of one or more of your captured media files does not match the sample rate on your source tape. This may cause the video and audio of these media files to be out of sync. Make sure the audio sample rate of your capture preset matches the sample rate of your tape."
For the past day I have been scouring the user manual, this discussion group and training tapes from Lynda.com and can not resolve this issue. I have determined that the source tape is 12 bit or 32 kHz and yet can not find a way to set up capture preferences to 32 kHz. Is this the problem/resolution? Page 320 of the user manual shows the QuickTime Audio Settings dialog box but I can't find it in FCP or Quicktime. Is this where I make the change to 32kHz?
After doing the first test, I tried again and ran into a new problem—it stopped capturing with the message: Locating timecode break [press esc to abort]. It never seemed to resume capturing and I pressed escape to abort. If I'm reading FCP time code window correctly I received this time code break message within a section I had already captured previously (with the audio sync warning).
I have done several capture tests at different points in the tape and on different tapes all with the same results. I've used the capture clip and capture now buttons. I've tested with drop frame turned on and off. Confirmed my setting of: At timecode break "Make New Clip." Confirmed my Easy Setup as DV-NTSC. My capture preset is DV NTSC 48 kHz. I've turned off and on FCP. Restarted my computer. Restarted my computer with the shift key down and ran permissions.
Any ideas are GREATLY appreciated, T.I am concerned about available memory when capturing to my hard drive and the babysitting and extra steps involved considering the amount of tape I want to capture...but it does work that's GREAT!
This is always a concern, but in your case I think having the camera and external on the same bus was causing your problem. You may have to capture a little and then transfer, rinse and repeat. Just don't try to do too much at once and let your System Drive get too full, you'll run into other problems there. Slow and steady is the pace!
I shouldn't have stacked my questions since you answered one and Chris answered the other. Don't know how to apply the answered question and who gets the points.
No problem, just mark it answered and divide up the solved and helpful points as you wish. All in all we really don't care too much about the points, but they do make us feel good! Thanks for your desire to use the forums properly.
K -
What does error code: U44M1I200 mean?
What does error code: U44M1I200 mean?
It indicates the installer failed with an unknown error. Please review the install log for the update you are attempting to apply. You can find details on how to locate and interpret the installation log file at Troubleshoot with install logs | CS5, CS5.5, CS6 - http://helpx.adobe.com/creative-suite/kb/troubleshoot-install-logs-cs5-cs5.html.
-
What does this error message mean: "Filename: Mips32.ari TFTP Error: 'File not found' in AP-105"?
Question: What does this error message mean: "Filename: Mips32.ari TFTP Error: ‘File not found’ in AP-105"?
Product and Software: This article applies to AP-105.
The root cause of this error is that the AP cannot perform a code upgrade.
Scenario 1
Check the ArubaOS code.
The minimum requirement to bring up an AP-105 is ArubaOS 3.3.3+ or ArubaOS 3.4.1+.
If the controller is running pre 3.3.3 code, upgrade the code to fix the issue.
Scenario 2
If the AP is not connected to the controller directly, bring up the AP in the controller and then connect it to the desired location. This process loads mips32.ari to the AP so that the AP can upgrade the code.
Scenario 3
The AP has no power adapter and you want to use the PoE feature. A few controller series like the 200 and 3000 Series do not support PoE. In this case, the AP cannot be terminated physically in the controller. Instead, connect the AP to the PoE switch, which is connected to the controller. Then assign a static IP configuration for the AP using the following commands:
apboot> setenv ipaddr <ip address>
apboot> setenv netmask <netmask>
apboot> setenv gatewayip <ip address of the gateway>
apboot> setenv master <ip address of the master>
apboot> setenv serverip <ip address of the TFTP server>
apboot> setenv bootcmd tftp
apboot> save
apboot> boot
Locally configure the TFTP server for the AP and load the mips32.ari file from the controller with the help of the TFTP application.I want to download this file Mips32.ari for AP-105 device. Please give me this file download link. APBoot 1.2.4.4 (build 26618)
Built: 2011-01-07 at 13:42:04Model: AP-10x
CPU: AR7161 revision: A2
Clock: 680 MHz, DDR clock: 340 MHz, Bus clock: 170 MHz
DRAM: 128 MB
POST1: passed
Copy: done
Flash: 16 MB
PCI: scanning bus 0 ...
dev fn venID devID class rev MBAR0 MBAR1 MBAR2 MBAR3
00 00 168c 0029 00002 01 10000000 00000000 00000000 00000000
01 00 168c 0029 00002 01 10010000 00000000 00000000 00000000
Net: eth0
Radio: ar922x#0, ar922x#1Hit <Enter> to stop autoboot: 0
Checking image @ 0xbf100000
Invalid image format version: 0xffffffff
Checking image @ 0xbf800000
Invalid image format version: 0xffffffff
eth0 up: 1 Gb/s full duplex
DHCP broadcast 1
DHCP IP address: 192.168.x.xx
DHCP subnet mask: 255.255.255.0
DHCP def gateway: 192.168.x.xx
DHCP DNS server: 192.168.x.xx
DHCP DNS domain: xx
ADP multicast 1
ADP broadcast 1
ADP multicast 2
checksum bad
ADP broadcast 2
checksum bad
ADP multicast 3
checksum bad
checksum bad
checksum badRetry count exceeded
DNS request 1 for aruba-master to 192.168.x.xx
checksum bad
checksum bad
checksum bad
T Using eth0 device
TFTP from server 192.168.x.xx; our IP address is 192.168.x.xx
Filename 'mips32.ari'.
Load address: 0x2000000
Loading: checksum bad
T T checksum bad
T checksum bad
checksum bad
checksum bad
T checksum bad
checksum bad
T T checksum bad
T checksum bad
checksum bad
T T T
Retry count exceeded; starting again
eth0 up: 1 Gb/s full duplex
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum badARP Retry count exceeded; starting again
eth0 up: 1 Gb/s full duplexchecksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad ThanKs :)
-
I got an iphone from Hong Kong which is locked one. Can anyone explain me what does a locked iphone means. How do I use it in India now, with my own sim card. How do I unlock it???
If your iPhone is locked to a wireless provider, only that wireless provider
can unlock it. Contact the wireless provider in Hong Kong to see if they
offer unlocking and if you qualify.
If your iPhone is locked to an AppleID that you do not know, return it for
a refund as it is useless. Only the person whose AppleID was used for
activation can remove the lock. There is no workaround for Activation Lock.
If neither of the above is what you are facing, provide more detail so someone
may offer a solution. -
I was playing with my ipad settings and noted in he advanced settings of Safari there was a place to view "website databases". When I selected this I saw a multitude of websites.
Can anyone tell me how these get there? Can a website be posted even if it was never went to? What does the space amount mean? For example, 1.5 kb...is this quite a bit? Would it indicate someone has gone to a site multiple times?
I share my ipad with my teenage daughter and I'm trying to find out if she's lying to me. Obviously she's swearing that she has "no idea" how these got there and I'm trying to keep her safe (she's only 14).
Thanks everyone.
Concerned MomThink of your PC and the 'temporary internet folder' where it keeps cached copies of web pages or elements off a web page for 'quicker display the next time you visit'. That's pretty much what that folder is. 1.5K is tiny. Probably just a basic page with some text on it. (you might be confusing 1.5K with 1.5 megabyte....megabyte is large...it's roughly 1000 kilobytes, so the 1.5K is a tiny file)
As far as I know, the only way info gets into that folder is if the browser has been to that site.
if you have a concern there are browsers out there, McGruff is one i've seen recommended, that allow some degree of parental control and supervision. That or you could passcode lock the iPad or enable the restrictions to turn off some parts of the device to have some control. -
What does (error code -600) mean?
What does (error code -600) mean?
I received this code in a pop up window while trying to open iTunes from my Apps folder.procNotFound
= -600, /*no eligible process with specified descriptor*/
Could be many things, we should start with this...
"Try Disk Utility
1. Insert the Mac OS X Install disc, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu at top of the screen. (In Mac OS X 10.4 or later, you must select your language first.)
*Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
3. Click the First Aid tab.
4. Select your Mac OS X volume.
5. Click Repair Disk, (not Repair Permissions). Disk Utility checks and repairs the disk."
http://docs.info.apple.com/article.html?artnum=106214
Then try a Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
(Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive.)
If perchance you can't find your install Disc, at least try it from the Safe Boot part onward.
Any change? -
What does "extracted channel PDF" mean and why does it continually duplicate on my desktop? I think it happens when I move a file in Finder to another file and when I copy some web files. I have to immediately move to trash all the duplications on my desktop. How do I avoid this on my Mac (Mavericks)? Thanks for your help!
What application is set to open PDF files? If you CNTRL click on the file and open with Preview does the problem occur?
If not change the default application to open PDF files to Preview.
You can do this by highlighting the file and either use CMD i or Get Info , this will open a window with the info on the file with an option to change the application that opens the file.
That's all I can think of. -
I understand that when using Numbers/Pages - an up-arrow on a document means that the file is still to be uploaded to the cloud, what does a down arrow mean? It seems the document can't be accessed until the arrow clears.
I believe what it's supposed to mean is that some changes were made to the document on another device, and those changes were saved back to the cloud. Now you've opened iWork on a different device to access that document - it compares the document you've got locally with the one in the could, sees some recent changes and downloads them.
What gets me is why this sometimes happens even when I've not made any changes to a document from another device. -
What does "on my mac' mean and how do i delete or reduce the number of items in there?
What does "on my mac" mean and how do i delete or reduce the number?
Hi ya
I'm seeing this on my email screen, on the left hand side - under the "RSS Apple". The number of items in there is now 752. It's preventing me from sending and receiving emails in my AOL account.
Any help would be deeply appreciated.
Thank you. -
What does "update carrier settings" Mean? Settings for what?
What does "update carrier settings" Mean? Settings for what?
It means just what it says. Carrier settings are the settings the carrier installs on the phone to connect it properly to their network. Periodically, carriers push updates to those settings. You should accept them.
Maybe you are looking for
-
How to add customized value to drop down by index binded to model attribute
i have to Ui element Drop down by index to which i have binded model attribute for populating the values, now i want to add a customized value to it like "choose all". how can i do this ?? Thanks and regards, Aditya Deshpande
-
Why won't my Mac Air wake up when it's supposed to?
Why won't my MacBook Air wake up when it's supposed to?
-
CUCM SQL Query - MGCP EPs IP Addresses
Hello, CUCM 9.x. Could you please advice me the CLI sql query to get registered MGCP endpoints IP addresses? Thank you in advance.
-
hi friends, i have a trigger on key enter, but it is not firing when i press the enter key, why it is not working. i want the trigger to be fired only if the user press Enter key thanks Kris
-
Metachain failed with status 'X'.
Hi experts, I have an issue with the meta chain which has been canceled with the status 'X'.And some of the local process chains are not getting triggered. Please help me. Regards Sam