What dose it mean when ipod just blinks the apple symbal and wont charge
My ipod wont charge and now when on charger will just blink the Apple symbol
Hi Julesvamc,
Thanks for visiting Apple Support Communities.
When an iPod only shows an Apple logo, this usually means that the device needs to be restored.
You can find more information about this symptom, as well as step by step instructions for restoring an iPod at this page:
iPod only shows an Apple logo and doesn't start up - Apple Support
You may need to restore or update your iPod, iPod mini, or iPod nano by placing it in Disk Mode if only an Apple logo appears when you turn it on.
All the best,
Jeremy
Similar Messages
-
When I charge my I pad I just get the apple sign and not a charge. After hours of charging sometimes I might get a slight red battery but then it returns back to the apple sign. I am using the correct battery.
warnerm wrote:
I have a ipad 2. I have the 10W wall charger.
I did try to reboot the ipad by holding both keys down and the Apple logo did appear but the Ipad would bot restart.
I do own a Iphone and tried charging earlier by switching out the cables and not the charger. In fact in the apple home we have three i-phones and have tried muliple cables with no luck.
Thanks for your help.
That doesn't sound good at all.
Since the Reset didn't work, try a Restore. Note that it's nowhere near as quick as a Reset. Connect via cable to the computer that you use for sync. From iTunes, select the iPad/iPod and then select the Summary tab. Follow directions for Restore and be sure to say "yes" to the backup. You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod. Again, say "yes."
Finally, if the Restore doesn't work, let the battery drain completely. Then recharge for at least an hour and Restore again. -
I plugged in my ipod to recharge it and for some reason, it just stopped and only the apple logo is showing. I may have unplugged it before it was done, not even sure at this point but now only the apple logo and I can't even shut it off. Any ideas of what I can try now? Thanks much.
Have you tried a reset ? Press and hold both the sleep and home buttons for 10 to 15 seconds and see if it then reboots - you won't lose any content, it's the equivalent of a computer reboot. If that doesn't work then you might better help in the iPod forum (this is the iPad forum)
-
HT4623 my phone is blinking the apple symbol and wont turn on, what can i do?
i tried to update my software and when it asked to restart i said yes and now it blinks it will not turn on what can i do???
See Here > http://support.apple.com/kb/HT1808
You may need to try this More than Once...
Be sure to Follow ALL the Steps...
But... if the Device has been Modified... this will Not necessarily work. -
how can i reset my iphone? I chose to reset my settings and all I see now is the apple logo, but does't want to reset.
Try this reset ...
Press and hold the Sleep/Wake button and the Home button together for at least ten seconds, until the Apple logo appears.
If that doesn't help, restore the device > iTunes: Restoring iOS software -
What dose it mean when my Iphone5s show a blue screen
What dose it mean when my Iphone 5s show a blue screen???
My Iphone is my baby. And I just dont know what to do..... All I did was letting it do it updated and when it started to do the blue screen of daeth then started up again. And it do that over and over and over.... I dont know what to do.... Please help me..... I dont want to tell my mom my phone is broken..... Is there any way I can fix it....Hi Sky_Drz,
Welcome to the Apple Support Communities!
I understand that situations like this can be both frustrating and concerning. There are some troubleshooting steps that I would recommend. Please work through the troubleshooting steps in the attached article.
iOS: Not responding or does not turn on - Apple Support
Best regards,
Joe -
My iphone just died on me, wont turn on and when it is plugged into the charger it just blinks the apple sign at me, what can I do?
Try these suggestions and if no change take it to an Apple Store Genius bar
http://support.apple.com/kb/HT1808 -
What does it mean when I keep getting the following message on my IPad2:
Usually it's because you are not making internet connection via wifi.
Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Cheers, Tom -
What does it mean when you get a "The iTunes library file cannot be saved. There is not enought memory available." ? And what can I do to correct it?
Well, I installed the latest iTunes this AM, works perfectly. Although for some reason it did lock up after playing a song today.
Horror stories? That's a bit overly dramatic.
No, it isn't.
The issue you are experiencing is one that has occurred in multiple versions of iTunes, a simple search would have revealed this.
A simple search was conducted, no one seemed to have an answer. Do you always adopt such a haughty attitude? Or was I just lucky. -
HT4101 What does it mean when it says that the USB device requires too much power?
What does it mean when it says that the USB device requires too much power, when using the ipad lightening pin camera connection kit?
Just that. The iPad allocates a certain amount of power to that port. If the device you're trying to plug in wants more than the iPad is willing to give, it'll trigger that warning.
If it's something that you just must hook up you can try using a powered USB hub, but results are mixed at best.
What are you trying to hook to your iPad? -
What does it mean when I click on my wifi name and it show I'm on my wifi, but the network keeps thinking and the ipad says, Safari cannot open this page because it is not connected to the internet. ?
When you click on the WiFi network name, have you also provided the password for accessing the network? You should get a dialogue box asking you for the security information the first time you connect.
If you are not able to connect, you might want to go to Settings > General > Reset > Reset network settings.
Then go back to Settings > WiFi and select your network name again and make sure the security information is now entered correctly.
If you still cannot connect, power down the router, wait a few minutes, power up the router, with the iPad powered down the whole time, and after the router has had several minutes to stabilize power up the iPad. See if it now connects correctly. -
What does it means when you turn on the macbook and a file with a "?" mark flashes?
What does it means when you turn on the macbook and a file with a "?" mark flashes?
It usually means some system files are missing or corrupted. Reinstalling OS X is the fix:
Reinstall OS X without erasing the drive
Do the following:
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install the Combo Updater for the version you prefer from support.apple.com/downloads/. -
what does it mean when you're about to install itunes and it says This update requires OS X version 10.6.8 or later.??? i don't understand... Can someone please explain to me what that means...??? And how to fix it.
1. It means exactly what it says. Apple dropped support for earlier Mac OS X versions in iTunes 10.7.
2. Update the computer to 10.6.8. If it's running a Mac OS X version prior to 10.6, this requires buying a Mac OS X 10.6 DVD from the online Apple Store, which requires an Intel Mac with at least 1GB of RAM.
(93025) -
My phone is always charged and always on but when i make or recieve a call it shuts down after 2 mins and just shows the apple icon and after another 2 mins will restart, any ideas what is wrong?
You may have to restore your phone to correct the problem.
-
what does it mean when you try to update i tunes and it tells you "itunes has an invalid signiture. the download has been removed"?
What kind of things are you seeing as disabled? The administration might have disabled some features because they don't fit in the structure of the community that has been built over the last few years. This community used to be based on a forum platform called Lithiu . At the beginning of the 2012 it was moved to a forum platform called Jive. It brought a lot changes to the community. Some of which many of us regulars are still finding after almost a year.
Maybe you are looking for
-
TCode for vendor trial balance (and not profit centerwise vendors list)
Hi I want vendor's trial balance report. My requirement is that i want list of vendors with the balances with debits and credits separately. There should be four columns like: Vendors, Debit (Amt), Credit (Amt), Net. I checked SDN websites also. The
-
ISE v1.1 NAD 6500 failed to decrypt Key......
Hello everyone , I´ve implemented 2 Cisco ISE v1.1 in HA to run MAB and 802.x Authentication / Authorization. Using Local ISE DB and Active Directory as an External Identity Source for wireless and wired users and devices. This was working fine 2 wee
-
Changing character encoding in ps xml pub. from utf-8 to iso-8859-1
I am using xml publisher to generate a report in a pdf format, now my problem is user has entered a comment which is not supported by utf but in iso-8559-1 its working fine, I tried to change the encoding in people code, xml doc file ,schema and xlif
-
Hello Experts, I have the following requirement in a report. I have a Material prognosos report which gives open amount in local currency. Now as soon as I display the report, I have to make the user to choose a list of target currencies which he can
-
How to count subforms and add a value to a dropdown?
Hello! I want to make a form with a subform that the user can dublicate by clicking a button (JS: ... addInstance(1);) after he dublicates the subform serval times and entered some text in the fields i wanto to count the subforms and go in every subf