What drivers do I use when installing windows 7 on macbook pro late 2013?

I purchased a new macbook pro from bestbuy. I would like to install windows 7 using bootcamp. Now I have read online that macs come with a driver cd well mine didn't and I got it new in sealed apple box..
What or how can I go about getting windows 7 to fully work on bootcamp.. I've yet to try to install windows 7 yet beacuse I am lost when it comes to this cd and the drivers...

See -> http://manuals.info.apple.com/MANUALS/1000/MA1636/en_US/boot_camp_install-setup_ 10.8.pdf.
In addition to the Windows disc (or USB flash drive with the Windows installer) you'll need a 8GB+ flash drive.
The referenced manual - on page 3, I think, gives you a run-down of what you'll need before you begin the installation. You may also want to post any further Boot Camp questions in the Boot Camp forum -> https://discussions.apple.com/community/windows_software/boot_camp.
Good luck,
Clinton

Similar Messages

Installing bootcamp on macbook pro late 2013 fails on 64% files expansion

I am trying to install Windows 7 on macbook pro late 2013 but everytime, it gets stucked on 64% while expanding the files. I used the same disk on a non retina macbook, and all installed well. What can be the issue?

The Boot Camp help manuals are located here: http://www.apple.com/support/bootcamp/
The Boot Camp Discussion Community is located here: https://discussions.apple.com/community/windows_software/boot_camp

Trouble with screen resolution when using Parallels and ACT on Macbook Pro (late 2013)

Hello, I have installed my Sage ACT 2013 software on my Macbook Pro 13" Retina (late 2013) computer that has 16GB of RAM and an i7 core processor using Parallels 9 desktop and Windows 7- 64bit. The problem is that the screen resolution is very small and condensed to the left side making reading the title boxes and content very difficult. I reached out to Parallels who was unable to resolve the screen resolution by either adjusting the display settings or the Windows 7 video settings. Right now they have the Resolution listed as "Scaled" as the "Best for Retina" & "More Space" options did not help the issue. What is even more strange is that I have Office 2013 installed on the Parallels side so that it can interface with ACT and those screen resolutions read just fine. Are there any ACT/MAC users out there that might have any insight for me? Thx!

See -> http://manuals.info.apple.com/MANUALS/1000/MA1636/en_US/boot_camp_install-setup_ 10.8.pdf.
In addition to the Windows disc (or USB flash drive with the Windows installer) you'll need a 8GB+ flash drive.
The referenced manual - on page 3, I think, gives you a run-down of what you'll need before you begin the installation. You may also want to post any further Boot Camp questions in the Boot Camp forum -> https://discussions.apple.com/community/windows_software/boot_camp.
Good luck,
Clinton

Is it possible to install windows 8.1 on macbook pro late 2013?

hi ,
Is it possible to install windows 8.1 on late 2013 macbook pro?
I have tried installing it twice but both of the time i got an error
Windows could not update the computer's boot configuration. Installation cannot proceed.

Maybe people have found a solution already but yesterday I managed to install Win 8.1 as a BootCamp on my new 15" retina MBP. I followed the steps John Guo described but with a couple of changes as his approach failed for me.
1. Make sure you are starting from a single partition.
2. Create the Windows install USB from the ISO and also allow BootCamp Assistant to create download the drivers - but untick the option to install windows.
3. Open Disk Utility and create a new partition and format as MS-DOS (FAT) rather than leave as free space.
4. Restart your Mac and use the option to boot into the Windows part of the USB not the EFI-boot.
5. Follow the install
6. When it comes to the drive selection select the FAT drive. Windows installer will say it cannot install here as it needs to be and NTFS partitiion (in previous atempts I always got the message to say the partitiion was using GUI partition table so could not install even though it was formatted to NTFS).
7. The format to NTFS should work fine and install proceed.
8. When the installer reboots the machine you will need to use the boot option to ensure you boot back into Windows.
9. Once installed the bootcamp driver install runs automatically and for me all drivers run fine even the NVIDIA, which I've seen some people mention having issues with.
I was inpressed with Windows automatically scaling the text to 200%, which meant it was using the full 2880x1800 resolution so everything was crisp but the windows and text was scaled nicely. I changed this 150% to give me some more real estate.
I'm guessing that by formatting the new partition as FAT it creates a MBP within the new drive that is writable by windows but I'm not a windows guru so this is a guess. But anyway, this work perfectly.
hope this helps some people.

How to clean install os x on macbook pro late 2013 using usb (offline) (without recovery direct download)

hi,
Im trying to clean install OS X from last month using inbuild recovery partition method. Due to slow internet connection Im unable to complete the installation. I tried many times using this intallation process but it failled to complete the installation. My internet connection is steady but due to "time out" the whole installation process is skiping. So Im not able to use my brand new macbook pro late 2013 from last month beginning. Please provide an alternative solution to install os x.

For several years now, Apple has acted as if everyone on the planet has high speed Internet access. That is obviously not the case for many people, and for them installing or reinstalling any OS X version since Lion has been a problem.
I can only suggest that you take your MacBook Pro to a location that has a faster, publicly accessible Internet connection and download it there. An Apple Store would be ideal, but if that is not an option, a public library may offer high speed Internet, as do many hotels, coffee shops, or similar locations where you may have to pay a small fee.
When the download completes, you can copy the Install OS X Mavericks icon to another folder or an external storage device such as a flash drive, where it will remain available to use again, as often as you wish. Do that before proceeding with the Mavericks upgrade, otherwise the installer will erase the file.
The installer icon resembles the following
(Launchpad)
The following will also appear in /Applications:
Copy that to another location, such as Documents, by holding an option key while you drag it there.
Of course, every time Apple releases an OS X update you will need to download another, rather large file.

After installing the new Yosemite OS on my Macbook pro late 2013 touch trap has its own mind. Any others with this problem? What should we do?

After installing the new Yosemite OS on my Macbook pro late 2013 touch trap has its own mind. Any others with this problem? What should we do?
Even I tried to get back to Maverick but the touch pad doesn't work again. well, it works for a couple hours then start doing things but its own. it is so annoying.

Hello josefromlaie,
Thank you for using Apple Support Communities.
The following article provides some effective steps to troubleshoot trackpad issues:
Intel-based Mac notebooks: Troubleshooting unresponsive trackpad issues
Regards,
Jeff D.

Sound stops working while using headphones on Retina Macbook Pro (late 2013)

I have a brand new Retina Macbook Pro (late 2013) with OSX 10.9.1 installed. The sound continuously stops working when I'm using my headphones (which I use on a daily basis). I've noticed that when I unplug the headphones, the sound from the internal speakers and the headphone port stops working.
I've already checked other answers and have tried their suggestions:
I've looked at the sound settings and it is not set to mute.
I've tried unplugging the headphones several times in a row and that still doesn't work.
I don't see a red light in the headphone port.
I've checked the headphones and there is nothing wrong with them (I use them with other devices).
I've tried using different headphones, but the problem persists.
The only way to get the sound working again is by restarting my laptop which is very inconvenient. I use this laptop for working and having to restart it every time I unplug my headphones is just not a solution. I honestly have no idea what is going on. This is a very new laptop (and my first Macbook); I've had it for less than 3 months. The laptop stays on my desk and has not been dropped or damaged in any way. This is a very expensive laptop and the last thing I would expect is for there to be a problem like this.
If anyone has a solution to get rid of this problem once and for all, please let me know!
Thank you.

I have a brand new Retina Macbook Pro (late 2013)
Please read the warranty paperwork that came w/your computer. You have 14 days to return the computer w/no questions asked. You have 90 days of FREE phone tech support on top of your standard 1 year warranty unless you also purchased AppleCare which gives you an additional 2 years of coverage plus FREE phone support. Strongly suggest that you take FULL advantage of the above before it runs out. Let Apple deal w/the problems. If you DIY and mess up, your warranty will be VOIDED!

MacBook Pro late 2013 does not show login window after waking from sleep

MacBook Pro late 2013 does not always prompt for login, but opens directly to desktop, even though security settings are setup to prompt for password after 5 minutes. Up to now, this only has happened on battery, machine goes to sleep or lid is closed, 10 minutes pass, lid is opened and desktop is shown instead of lock screen. Console shows, that the machine was actually sleeping (10 min no log entries) and also does not show any error in regards to login window.
This behaviour occurs randomly and I could not track down any root cause/behaviour, yet. Sometimes everything behaves as it should.
Any ideas?
Thanks
marcus

Count me in, I have the same issue, and from what I read here, it looks like a Yosemite/SSD related issue ?
I'm not 100% sure if it started when I put a SSD in my old iMac 2009 (as a fusion drive) or if that's after that when I upgraded to Yosemite...
I did disable auto poweroff like suggested in another thread : Mac freeze during the night sleep.
sudo pmset -a autopoweroff 0
We'll see if it helps.
It happens toughly a couple of times a week.

Have iPhone 5s setup on windows 7 machine and in iCloud. now have 15" macbook pro late 2013

I want to start using my macbook pro late 2013 loaded up laptop to start using my iphone 5s with. I have transferred all music and apps virtually everything is in the versionof itunes on laptop and has been authorized.
now how do I use it as when i plug phone in it sees it as mass usb storage ie.... i can transfer pictures not much else.
any help appreciated.
thanks

Hi chevysales!
If you iPhone is not appearing in iTunes on your MacBook, you will want to see this article for troubleshooting steps:
iOS: Device not recognized in iTunes for Mac OS X
http://support.apple.com/kb/ts1591
Once your iPhone is recognized in iTunes, you can use this article for information on how to sync:
iOS: Syncing your data with iTunes
http://support.apple.com/kb/ht1386
Thanks for using the Apple Support Communities. Have a good one!
-Braden

Installing windows on MacBook Pro

I am looking into installing Windows on my Pro because I need Visual Studio for programming and just need some questions answered.
1. Is there a Mac native alternative to Visual Studio? I am using it for a Visual basic class I am taking and we are creating windows applications.
2. Can I buy an external hard drive to run Windows OS from? I opted for the ~256gb SSD MacBook Pro and am not wanting to waste storage space on Windows OS, especially since I do not foresee using it after this class.
3. If I cannot run Windows from an external hard drive: How easy is Windows installation, as well as how easy is it to remove Windows OS when I am finished using Visual Studio? Are there risks to my MacBook accompanied with Windows installation?

1, No
2, No, Microsoft doesn't allow that
3, Read http://manuals.info.apple.com/MANUALS/1000/MA1583/en_US/boot_camp_install-setup_ 10.7.pdf

What is the cracking sound when I open my MacBook Pro lid?

When opening and closing MacBook Pro lid, it makes a cracking sound. Does anyone have an idea what it could be? It's not the hard drive because Geek Squad ran a test and everything passed.

Try this: Loosen the screws in the rear of the MBP (by the hinge) and re-torque them. See if that will alleviate the problem. You will need a 00 Philips driver.
Ciao.

Instaling ML on Macbook pro late 2008 from dmg problem

Hello all
a friend of mine has a macbook pro late 2008 with snow leopard installed.
He wanted me to clean install the machine and install ML on it
i checked the requirements and i saw that this is possible
went on my mac mini and restored the image file to a usb stick and holding option key while booting i started the process
first erased the hard drive and then back to main screen press install ML
the next screen after confirming that i agree the dialog box was reading tyhe instalation files..it went throughh till the last bit and then just stuck there!
left it almost all night and nothing happened
Any ideaw on how to proceed?
Maybe the installation image that i have used is only for my mac mini and that is the reason that this happens?
a possible solution is to install snow leopard again and inform him to buy the software so as to be machoine specific from the mac app store?
Any help will be much appreciated
Many thanks

Your friend has to purchase OS X Mountain Lion with his/her Apple ID. If you install OS X Mountain Lion without having purchased it with his/her Apple ID, he/she won't be able to reinstall OS X Mountain Lion if it gets damaged, so this is dangerous.
He/She must purchase OS X Mountain Lion, so he just have to open  > Software Update and install all available updates. Then, open App Store and purchase OS X Mountain Lion, so it will be downloaded into his/her MacBook and the Mountain Lion installer will show up when the download finishes, so just follow the steps to upgrade to OS X Mountain Lion.
He/She should make a backup of his/her files with Time Machine or Carbon Copy Cloner before upgrading, and also, check if the applications are compatible > http://www.roaringapps.com
The OS X Mountain Lion version used is the same for all Macs (except the 13-inch MacBook Pro with Retina display, and the Late 2012 Mac mini and iMac because of driver problems), so this is not a problem

BSOD when installing windows 7 drivers using bootcamp in macbook pro late 2013

I followed the bootcamp instructions and installed windows 7 in my macbook pro 13 inch late 2013. But when the bootcamp starts to install the required drivers, halfway through the computer goes to BSOD. And after restart windows shows many error messages of "validation error".
I have a student licensed windows 7 professional.

I had the same problem. I was installing a Debug Build of Windows 7 on MacBook Pro 15" Late 2013 with a student license and it would die with BSOD while running BootCamp at the end of Windows installation. I solved the probelm by downloading a non-Debug version of Windows 7 Professional with Service Pack 1 and re-trying the installation from scratch. That is, I went back to OS X, launched BootCamp Assistant, erased the previous partition of Windows and re-created it again. After that, I installed a fresh copy of the right flavor of WIndows and it worked flawelessly.

How to install windows on macbook pro me294 using downloaded drivers?

Recently I bought a MBP and I'am going to install windows on it because of my job. I have a problem with bootcamp assistant: I have downloaded the bootcamp drivers but when I am creating the setup disk it automatically chooses to download the drivers again! What should I do?

i have done this steps but when i boot the usb key it freezes in the first screen ( selecting languages ) ! but i believe it doesn't freezes, it is because it doesn't recognize my hardware. when i was installing win8 there were no problems like this!

Blank screen when installing Windows 7 on my Late 2009 iMac

So before I drop everything and start hitting my head agains the wall I figured I would make one more stop and ask folks on the forum.
I'm trying to install Windows 7 Pro on my "late 2009" 27" iMac. Here is a quick config.
Here are the exact steps I take:
1. Start Boot Camp Assistant
2. Select both options to download Windows components and install Windows 7... and make the partion (80GB) allocation to Windows partition
3. Insert the Windows installation disc (Pro, full version)
Everything seems to be running smooth, meaning I see the windows installer and I'm able to select the partition where I want Windows to reside and here are the last few things I see...
Right after the Starting Windows the screen goes blank and that's is. If I simply restart at this point it goes back to the Starting Windows and blank screen again (no option to choose OS).
Since the wireless keyboard is not functioning at this point I learned to take out the CD from the drive by holding the mouse button on startup. From there I insert an installation disc for Snow Leopard and boot from disc by holding the "C" button on my USB keyboard. It lunches the Utilities where I'm able to select The Start Up Disk and here is where I actually see both partitions. That's how I got back to OS.
So what am I doing wrong? I though that it had to do something with the video driver but if the installer works than I should be able to go in there after it's in place and run the correct driver from the WindowsSupport folder that I downloaded earlier. I have tried this with 32-bit and 64-bit version of Windows 7 pro with the same negative result.
Any help would be greatly appreciated. I called the App store to see if they can assist but the only thing they suggested was CrossOver which doesn't help me.
Does anyone have any ideas on what to do/change?
Thank you.
Best regards,
Marcin

Got it!
After posting my question I noticed the "More like this" category and the second discussion was a hit.
https://discussions.apple.com/message/11290644#11290644
It was a display driver. All I needed to do was to boot from the CD again and following the directions in the post.
Worked like a charm.

What drivers do I use when installing windows 7 on macbook pro late 2013?

Similar Messages

Maybe you are looking for