What exactly to install? 10g OEM

I want to install 10g OEM on a fresh Linux install. But I am not sure exactly what I need. I downloaded:
Linux_Grid_Control_full_10_1_0_3_Disk1.cpio.gz
Linux_Grid_Control_full_10_1_0_3_Disk2.cpio.gz
Linux_Grid_Control_full_10_1_0_3_Disk3.cpio.gz
and
ship.db.lnx32.cpio.gz
ship.ccd.lnx32.cpio.gz
from otn. Do I need to install the Database and then the GridControl? Or will the Grid Control install a database as part of the install? Confused on what exactly is needed.
Bob

please ignore my previous mail
i made a typo in my previous reply intead of 9205 it is 9015.
yes bob Grid Control install a 9.0.1.5 database and it
is a part of intallation choose option EM with new Database if you don't want 9015 db then you have to install Databse(eg 10103) and choose option EM with existing DB
Regards
Nazim

Similar Messages

[Q] How to by pass RAM check while install 10g OEM?

I am installed ORACLE 10G Grid Control (OEM) on Redhar LINUX. There has message pop up :
you only have 756 MB RAM, 10g need 1024 MB RAM
Does there has way by pass it?
Thanks.

Hi,
You need only 512 Mb if you install on a separate DB, what I recommend you.
If you choose "new db", oracle is going to install a full rdbms engine (9.0.1.5) and a new db. It requires about 9G with default install.
You could install your own Database, block_size=8192, job_queue_processes=10, no dispatchers, remote_login_passwordfile=exclusive with Oracle 9.2.0.5 (or 9.2.0.4) and a listener. This will cost you much less disk space.
Regards
Laurent

Whats needed to install 10G 32 bit on Windows server 2008 R2 x64

Hello,
I cannot use 11g with what I need to use on the server.
I have installed 10.2.0.3.0 32 bit on the server 2008 R2 x64. It is not working and i get a page not found error when i browse to our application. I know i need to install a patchset or something newer than 10.2.0.3.0. How do i install the 32 bit 10.2.0.4.0 patchset on my server? Is there a different patchset i need to install? When i tried to install the patchset, it said:
Checking installer requirements...
Checking operating system version: must be 5.0, 5.1, 5.2 or 6.0. Actual 6.1
Failed
What do I need to do to get 10g 32 bit to work on my server 2008 R2 x64 server?
Thanks!

Replying for your patchset installation pre-req error:
Use below command:
./runInstaller -ignoreSysPrereqs
Review MOS note 763143.1 for more info.

How to find out what products are installed 10G

I have been getting questions lately "Is OLAP installed, locator... " in 10G, normally
there are tables sys tables that tell generally whats installed but not specifically. Then
in the 11G enterprise manager I saw the database configuration pack that comes
with enterprise manager that really defines -> whats installed, the patch level -> basically
everything... So my question is are there any system tables, stored procedures, or packages that
would give me this information in 10G without having to install the database configuration
pack into a 10G enterprise manager.
thanks

You can query dba_registry for this information.
SQL> col comp_name format a40
SQL> select comp_name, version, status from dba_registry;
COMP_NAME                                VERSION                        STATUS
Oracle Database Catalog Views            10.2.0.4.0                     VALID
Oracle Database Packages and Types       10.2.0.4.0                     VALID
Oracle Workspace Manager                 10.2.0.4.3                     VALID
JServer JAVA Virtual Machine             10.2.0.4.0                     VALID
Oracle XDK                               10.2.0.4.0                     VALID
Oracle Database Java Packages            10.2.0.4.0                     VALID
Oracle Expression Filter                 10.2.0.4.0                     VALID
Oracle Data Mining                       10.2.0.4.0                     VALID
Oracle Text                              10.2.0.4.0                     VALID
Oracle XML Database                      10.2.0.4.0                     VALID
Oracle Rules Manager                     10.2.0.4.0                     VALID
Oracle interMedia                        10.2.0.4.0                     VALID
OLAP Analytic Workspace                  10.2.0.4.0                     VALID
Oracle OLAP API                          10.2.0.4.0                     VALID
OLAP Catalog                             10.2.0.4.0                     VALID
Spatial                                  10.2.0.4.0                     VALID
Oracle Enterprise Manager                10.2.0.4.0                     VALID
17 rows selected.

What exactly is Office Tools in the sharepoint Designer 2010 install?

I was looking for a solution to problems we have been having with Office 2003 and Sharepoint 2010 and I was able to fix it by installing Sharepoint Designer 2010. However I didn't want to install the entire Sharepoint Designer software on the clients PC
so I just installed Office Tools from the installer but I can't figure out what it's changing for this to work.
Can you give me an idea as to what exactly being installed in the Office Tools component of Sharepoint Designer?
Regards

According to you description,my understanding is you want to know how it fixed your problem by installing Office Tools.If yes,please refer the below description.
All Microsoft Office components from MS Office 2007 and newer contains a component (OWSSUPP.DLL) that implements full integration with SharePoint. Full integration is often noticed by the user in that it enables checking documents in and out from the application
(as opposed to manually checking out and downloading the document, open the application manually and work with the file, manually uploading the file to the right SharePoint site and checking it in again).
So when you install Office Tools in the Client machine,the above dll will get installed an enabled in the browser and user will get option to open the document/excel file from the SharePoint site using the local Office Product which was installed in the
client machine.That dll integrates the SharePoint application with Office Product.
Best Regards,
Pavan Kumar Sapara.
Please remember to mark your question as answered &Vote helpful,if this solves/helps your problem.
s p kumar

In the second step of bootcamp, I am supposed to either check the box where it says create a windows install disk, what exactly is this? Do I need to do this?

In the second step of bootcamp, I am supposed to either check the box where it says create a windows install disk, what exactly is this? Do I need to do this? I have a windows 7 install disk, but I don't know what this means.

If you already have Windows on a DVD or USB drive, you don't have to tick that option. That's only for people who have Windows on a ISO file and have to burn it into a USB drive

Installing the OEM Agent on an AIX Clustered Environment

I have installed the OEM 10.2.0.5 agent on a server (sgramchdd50) that is part of an AIX HACMP cluster configuration. The other node of this cluster is sgramchdd51 and the cluster name is sgramchdd52. After installing the agent the server name sgramchdd50 is hard-coded into the the $AGENT_HOME/sysman/config/emd.properties file as follows....
EMD_URL=https://sgramchdd50:3872/emd/main/
The problem is that when we failover to the other node (sgramchdd51) the agent no longer works because the inactive node is hard-coded in certain places. I need to hardcode the cluster name as it is always pointing at the active node in the cluster. I have tried the following (with no success)...
-Stopped the agent
-Modified the EMD_URL parameter of the emd.properties file as follows
-EMD_URL=https://sgramchdd52:3872/emd/main/
-Started the agent
However, starting the agent fails.
sagramihqchdd50<orabss:orurebss> $ ./emctl start agent
Oracle Enterprise Manager 10g Release 5 Grid Control 10.2.0.5.0.
Copyright (c) 1996, 2009 Oracle Corporation. All rights reserved.
Starting agent ........................................................................................................................... failed.
Here are the last several lines of the emagent.trc file...
*2010-07-14 16:02:38,799 Thread-1 WARN collector: MESSAGE_NLSID "Successful Name Registration Request Sent By Identity Provider(%)" is too long, truncating to "Successful Name Registration Request Sent By Identity Provider(%"*
*2010-07-14 16:02:38,864 Thread-1 WARN collector: the column name DiskActivityavwait in this condition does not exist in metric DiskActivity*
*2010-07-14 16:02:38,934 Thread-1 WARN collector: the column name DiskActivityavwait in this condition does not exist in metric DiskActivity*
*2010-07-14 16:03:22,988 Thread-1071 ERROR fetchlets.oslinetok: Process exitcode = 0, stderr = Error connecting to https://sgramchdd52:3872/emd/main/*
emctl status agent returned agent not running.
*2010-07-14 16:03:22,988 Thread-1071 ERROR engine: [oracle_emd,sagramihqchdd52:3872,ProcessInfo] : nmeegd_GetMetricData failed : Error connecting to https://sgramchdd52:3872/emd/main/*
emctl status agent returned agent not running.
*2010-07-14 16:03:22,988 Thread-1071 WARN collector: <nmecmc.c> Error exit. Error message: Error connecting to https://sgramchdd52:3872/emd/main/*
emctl status agent returned agent not running.
Can anyone help with the necessary steps to take to accomplish what I'm trying to do.
Any help would be very much appreciated.
Thanks.
Edited by: user11171364 on Jul 15, 2010 7:09 AM

I think you should try to find the solution in your DNS.
So lets say you name your node "MyActiveNode", your DNS only need to be modified to point to a different IP when failing over. The for the Agent it is still "logically" running on the same node.
Same thing if you should use a Server Load Balancer, use the name of the SLB to configure the Agent.
OK?
Regards
Rob
http://oemgc.wordpress.com

Can I ever use 10g oem-grid to deploy application?

Hi mates,
I have 10g OEM-GRID installed but no 10g-as installed...Is it possible to use the
part appliaction server feature in oem (dcmctl et.c) to deploy an application?
Is it something that can be done with 10g oem-grid?
Regardsssssss
shebby 9

Hi Jarred,
A way to create a "need recovery" situation.
1. Take the tablespace offline.
2. Copy the datafile (or one of the df's) to *.old.
3. Put the TS online again. And for the fun create a table and insert some rows in it.
4. Take the TS offline.
5. Copy the *.old datafile to what it was
6. Put the TS online again and bingo.
I think the existing alert log check will raise an alert.
Eric

What exactly is new in the ne iPad OS?

What exactly is new in the ne iPad OS? I downloaded it and don't see anything new.

You need to install it, as well as download it. Then the new features will be as shown here:
http://www.apple.com/ipad/ios4/

Only boots into safe mode (What exactly is left out in safe mode?)

my PBG4 hangs on a blank blue screen when i boot it, this happens on fresh (HD wiped) installs of both Tiger and Leopard. It boots fine from a dvd and while in safe mode.
i want to try to track down what exactly is causing the hang, i guess it is a hardware problem that only presents itself when all the stock drivers from apple are installed. is there a list somewhere of what is left out of a safe mode boot?

Hi slee!
"...this happens on fresh (HD wiped) installs of both Tiger and Leopard."
Do you mean that, you did an Erase & Install of Tiger 10.4.x, and the PowerBook G4, won't successfully startup, and the same, if you do an Erase & Install of Leopard 10.5.x?
Have you successfully installed either of those versions on the PB G4 before?
Are you using a Full Retail Version, of the Tiger Install DVD, and a Full Retail Version Of Leopard.
Or are you using a Model Specific DVD, from another model of Mac?
If this is the type of disc, then that may explain the unsuccessful installation.
The discs should look exactly like the images in the above links, and not say Upgrade, CPU Drop-in DVD, or "This software is part of a hardware bundle purchase - not to be sold seperately." on them.
ali b

Third Party Applications? What exactly are they?

Right,
I've read alot about the Blue Screen that appears when Upgrading to OSX Leopard. I am intending on upgrading tomorrow when my external hard drive arrives so I can Clone my 10.4.11 onto the external hard drive and upgrade the cloned version first but would like to know if I can check in advance for any of these' Third party App's'? and what exactly are they?
Regards,

A third party application is anything not made by Apple. It can also include products that Apple purchased fairly recently (some of those "Pro" apps) that weren't coded to Apple's specfications and haven't been well tested. Apple doesn't and shouldn't test their software with third party applications. It isn't their job to test other people's software. They probably make exceptions for things like Office and Photoshop, but that is a short list.
Most third party applications will be fine. The ones you have to worry about are those that ask for your password when you install them. They can then install any sort of incompatible software.
After you clone your hard drive, verify that you can boot from the external drive and all your data is there. If so, don't upgrade the external drive. Boot using the 10.5 DVD and immediately run Disk Utility and re-partition your internal hard drive to wipe it out completely. Then install Leopard. Do not use Migration Assistant. Re-install all your 3rd party applications that are 10.5 compatible. Be very careful about copying over from backup anything in a Library/Preferences folder. You can copy any preference file from a third party application back over - those are safe. Anything from Apple may have been upgraded. Only copy over the Apple files that you absolutely have to, such as your Mail folder and Address book file, for example.
It sounds like a lot of work but it will only take a couple of hours.

What exactly ARE the .pkg files that collect in the 'Receipts' folder?

Hi there all.
Those .pkg files that collect in HDD>Library>Receipts. What exactly ARE these packages for? How do they tie in with Disk Utility's 'Repair permissions' option? Why do we need to keep them?
It's all Unix to me ;0)

I used to delete .pkg files after I'd installed an application. I thought i was just the electronic equivalent of throwing away the empty box after I'd bought something.
The "cardboard box" icon encouraged me to think that.
Then someone said you should never throw away those.pkg files.
So I stopped.
But the only thing that has ever happened is that during permissions repair, I get a few lines here and there that say "could not repair permissions".
I have experienced no other problems of any kind over about the last 2 years. All applications running normally, nothing weird happening.

How to access Data Guard option in Oracle 10g OEM

Hi All,
I have Oracle 10g ENTERPRISE EDITION on Unix envoirement. I want to setup logical standby Database through Data Guard technology. But when I brows through OEM I do not find Link for DATA GUARD????
1) How to access Data Guard option from oracle 10g OEM.
2) Does It come with Enterprise Edition OR I have to install it separately.
Regards,
Darshan

I am managing almost everything through EM Grid Control. It is easy to setup and configure.
Anyways, if you have read the documentation on
Oracle® Data Guard Concepts and Administration and setup your environment accordingly then you should not have any problems. Atleast I can assure you that your production database will not be affected by it.
Just make sure that you follow each step and read thoroughly. If you have spare machines then you can test and record your configuration before performing it on your production db. This link will provide you with the information on DataGuard.
http://download-uk.oracle.com/docs/cd/B19306_01/server.102/b14239/concepts.htm
If you think that way then you will never be able to do any new stuff since you will always fear that something might go wrong. Go ahead pal, try it on test machines and you will know that it is not that difficult.
There are real experts who help people like us in this forum and I know that they are doing a pretty good job.
All the best.
Rgds
Adnan

Wb_rt_api_exec problem in 10G OEM

I'm trying to schedule a process in 10G OEM built in OWB. All validation, generation, deployment is fine. I can't find the docs to guide me in this process. The docs deal with the oem_exec_template.sql - which says to use wb_rt_api_exec.run_task for 10G OEM. Any idea what to do for scheduling in 10G OEM??
Based on examples in Metalink forum this is what I'm putting into the SQL script job in OEM. Errors included as well.
declare
ret number;
begin
ret:=runtime_owner.wb_rt_api_exec.run_task('RUNTIME', 'EASYDW', 'PROCESS', 'F4211LOAD','','',1);
end;
Copyright (c) 1982, 2004, Oracle. All rights reserved.
SQL> SQL> SQL> SQL> Connected.
SQL> SQL> 2 3 4 5 6 ret:=runtime_owner.wb_rt_api_exec.run_task('RUNTIME', 'EASYDW', 'PROCESS', 'F4211LOAD','','',1);
ERROR at line 4:
ORA-06550: line 4, column 6:
PLS-00306: wrong number or types of arguments in call to 'RUN_TASK'
ORA-06550: line 4, column 1:
PL/SQL: Statement ignored
declare
ret number;
begin
ret:=runtime_owner.wb_rt_api_exec.run_task('RUNTIME', 'EASYDW', 'PROCESS', 'F4211LOAD','','');
end;
ERROR at line 1:
ORA-20001: Task not found - Please check the Task Type, Name and Location are
correct.
ORA-06512: at "RUNTIME_OWNER.WB_RT_API_EXEC", line 620
ORA-06512: at line 4

Thanks guys. You were both right - wrong process name and too many parameters. And I realized I used the database locations value - not the Process flows locations.
This worked =
runtime_owner.wb_rt_api_exec.run_task('process flows locations', 'PROCESS', 'process name','','',1);
declare
ret number;
begin
ret:=runtime_owner.wb_rt_api_exec.run_task('DWDEST', 'PROCESS', 'PROC','','',1);
end;
/

What exactly is the receiving username/password required for

Hi All,
I have the ServiceDesk Appliance installed and trying to set it up.
I am now at Setup > Email > Server. Here in the "Receiving" section, what exactly do I need the "UserName"/"Password" for?
Can I use and existing username? or do I need a have a separate Username dedicated for the ServiceDesk?
Regards,
Yaser.

Yaser,
I will usually create an account specific for Service Desk. This is the user
account that will authenticate and Pop the mail form your mail
system(GroupWise..:-) ) back into the Service Desk application.
Hope that helps
Paul
>>>
> Hi All,
> I have the ServiceDesk Appliance installed and trying to set it up.
>
> I am now at Setup > Email > Server. Here in the "Receiving" section,
> what exactly do I need the "UserName"/"Password" for?
>
> Can I use and existing username? or do I need a have a separate
> Username dedicated for the ServiceDesk?
>
> Regards,
> Yaser.
Paul

What exactly to install? 10g OEM

Similar Messages

Maybe you are looking for