What happen to the VGA card????

ok
my pc :
pro:p4 3.2 1mb cash fsb 800
board: Msi 865 PE NEO2 P SERIES
VGA : HERCULES RADEON 8500
SOUND : CREATIVE LIVE
POWER SUPLY : 300W
+3.3V 12A
+12V 12A
-12V 0.5A
+5V 22A
-5V 0.5A
during playing games or even running winows applicatios  the monitor shows vertical lines of many colours and the pc crash and i had to restart , ome time i had to remove the card and put it again to work but the problem return back later???????????????????????????????????????//
i have the latest driver 4.10 and tried to install Windows Me the problem is the same
what happen to my VGA card /??
please help

i wil buy the power supply after tomorrow   what is the best????
do u think that problem only in the power ???
thanks for help
my msn messenger :  [email protected]
can we talk if u please?

Similar Messages

  • What happens if the Raid card battery goes dead?

    I just got my MacPro, Raid card, and 3 SAS drive. I set it up as Raid 0. The battery in the Raid card is good for 72 hrs. And that is to save the raid cache. So what happens if I leave the MacPro unplugged for longer then 3 days and the battery goes dead? Do I loose all my data?
    Thanks-Ray

    With an orderly shutdown prior to disconnecting the power, no problems should arise.

  • OTL -What happens to the rejected time card?

    Hi All,
    Can u pls clarify me this question on OTL? We have 2 buckets on time card. One is 1) On time bucket (Element) 2) Late hours bucket.(Element)
    We r using entry level approver where only the time entries with Late hours will be sent for apprval. Other time entries will be auto approved.
    Here the context is that the employee is seeking an excuse for coming late and hence the late hours are being sent for approval.
    Now when the approval is rejected, what happens to that time card? will it force the employee to submit that rejected time card?
    Or can the employee be still be able to submit the new cards without bothering abt the rejected time card?
    When the approval is rejected, it measns that the excuse is denied and later when we run the report we want to know
    the excused and non excused late entries.
    So i just want the employee to receive notification that it got rejected and the system should not force him to submit the rejected time card.
    Can you please answer this ?
    also all our time entries will be coming from swipe manchine. Is there a way we can make these entries just read only for the employee?
    Thanks in advance.
    Kiran

    Hi,
    Now when the approval is rejected, what happens to that time card? will it force the employee to submit that rejected time card?
    Or can the employee be still be able to submit the new cards without bothering abt the rejected time card?
    ----It won't force the employee to resubmit, the employee will be allowed to submit new timecards for a different period, but if for the rejected time period he has to use the rejected timecard and resubmit it.
    When the approval is rejected, it measns that the excuse is denied and later when we run the report we want to know
    the excused and non excused late entries.
    So i just want the employee to receive notification that it got rejected and the system should not force him to submit the rejected time card.
    ----The system will not force him to submit the rejected time card unless he tries to submit a timecard for the same time period.
    Can you please answer this ?
    also all our time entries will be coming from swipe manchine. Is there a way we can make these entries just read only for the employee?
    ----Could you please clarify your question on the "we can make these entries just read only for the employee?"
    Regards,
    Senthil
    Edited by: Senthilkumar Chandrasekaran on 27-Oct-2010 01:39

  • What happens to the outputs when I reconfigure the 6524 card?

    I have an application where I want to recongure the card throughout my program. For example I might initially want to set a single 8 bit port, so I could use Dig_Prt_Config and Dig_Out_Prt. Then I might want to output a batch of data using buffered IO so I use DIG_Block_PG_Config and DIG_Grp_Config to configure the card again. My question is what happens to the output states when I do this. If the port is then assigned to a group what happens to the outputs at that point? Do they remain unchanged until I do a Dig_Block_Out or do they all turn off? I guess I will find out when I try it, but it would save me from throwing away code if I knew now,
    Thanks,
    David

    David,
    I assume you have the 6534 board. On the 6534 board, reconfiguring the port will not affect the output value. Well, as long as the direction map doesn't change. Anyway, hope that helps.
    Ron

  • What happened to the "gift" with the 100ME cards?

    Does anybody know what happened with the special "gift" that was initially advertised to be packaged with the 100ME cards?   I purchased the GTX 970 Gaming 100ME from Newegg a few weeks ago, and there's nothing that fits that description in the box.  Now it looks like the MSI product page has removed any mention of the gift as well.  It's just a bit weird...
    Thanks!

    It seems it has been a limited offer and might also not been offered in all local markets. If the shop didn't list a gift being part of the package there simply is none.

  • When scrolling vertically there is an horizontal line which causes distorsion of the screen. I do not have noticed such concern on my iMac or on my macbook. What happen with the macpro ?

    When scrolling vertically there is an horizontal line which causes distorsion of the screen. I do not have noticed such concern on my iMac or on my macbook. What happen with the macpro ?

    MacPro bought in 2010
    MacBook Pro
    MacBookPro7,1
    Intel Core 2 Duo
    2,4 GHz
      Nombre de processeurs :          1
      Nombre total de cœurs :          2
      Cache de niveau 2 :          3 Mo
      Mémoire :          4 Go
      Vitesse du bus :          1,07 GHz
      Version de la ROM de démarrage :          MBP71.0039.B0B
      Version SMC (système) :          1.62f6
      Numéro de série (système) :          W804853GATP
      UUID du matériel :          716CB476-983B-5C43-B363-988FB608C01C
      Capteur de mouvement brusque
    État :          Activé
    System:
    Mac OS X 10.6.7 (10J869)
    Darwin 10.7.0
    Video DIsplay Card
    NVIDIA GeForce 320M :
      Jeu de composants :          NVIDIA GeForce 320M
      Type :          Processeur graphique (GPU)
      Bus :          PCI
      VRAM (totale) :          256 Mo
      Fournisseur :          NVIDIA (0x10de)
      Identifiant du périphérique :          0x08a0
      Identifiant de révision :          0x00a2
      Révision de la ROM :          3533
      Moniteurs :
    LCD couleur :
      Résolution :          1280 x 800
      Profondeur de pixels :          Couleurs 32 bits (ARGB8888)
      Miroir :          Activé
      État du miroir :          Miroir matériel
      Connecté :          Oui
      Intégré :          Oui
    Is that what you asked ?  Do you need other data ?
    Note that I have also strong distorison when running slides show with iphoto.
    Thanks

  • What happened to my gift card credit?

    I know how to review my purchase history in my iTunes account.  But, how do I find out what happened to a gift card credit?  Per my my account's purchase history, I only used $10 of a $50 gift card (assuming the culprit is NOT user error, e.g., I redeemed on the incorrect account).  Can I search "payment history" in addition to purchase history?  Thanks.

    I am currently in 'discussion' with iTunes about this very issue.  It's happened to me at least twice before when I redeemed a Gift card and didn't use the full amount.  A couple of weeks later... the 'credit' was gone!
    I also question as to why iTunes do NOT show gift card redemptions... VERY sus imho!!!  Why dont they??!!
    I have asked iTunes to provide me with a list of all my transactions for this year so I can see when, where and how my credits were used.  So far the best I got was "check your account balance".  They have said they will look into it from another side (ie. not via their customer support) but I will give them a week before I go to Fair Trading and make a formal complaint.
    I have provided them screen shots, dates, my purchase history etc. and the numbers just dont add up.  Either my credit balance expired (in the space of a couple of weeks) or someone is skimming accounts - which is on the iTunes system.  Either way iTunes have a case to answer!

  • After upgrading what happens to the apps on my 3G?

    I just received my iPhone 4 and put my backup from my iPhone 3G on. It works fine, and there is no more AT&T service on my iPhone 3G. I intend to use the 3G as an iPod Touch. I understand the SIM card needs to stay in the phone for this, even though it is not activated with AT&T.
    What happens to the apps that are still on my 3G? They are still working. I assume they will stay there until I need to sync. Then I will have to set up a new iTunes account, under a unique computer user name, for the 3G and buy the apps all over again for the 3G.

    Nope, the apps stay there until you delete them.
    I currently sync 2 iPhones and 2 iPod Touch units all to one iTunes store account, and per the Apple licensing, they all can run apps I have purchased. I had a similar question as you when I first started using multiple devices, so I sent an email to the app author for the app I wanted most to do this with. His response was that this is Apple's terms, so if I didn't want to purchase a second license to use his app on a second device, then I didn't need to (but he wouldn't stop me if I wanted to either). In the end, I found this app author to be very dedicated to his app, and very responsive to my comments/requests, so I did purchase a second copy of his app (yes, I had my wife create an iTunes account and purchase it under her account).

  • What happen when SSL daughter card fails?

    I'm using two CSM with SSL duaghter card with redundancy.
    What happen if the card fails? CSM fails too?
    Thanks.
    Andrea

    When the SSL daughter card failure is detected, the SSL daughter card is restarted causing all SSL flows to fail, and they will need to be re-established.
    During a supervisor engine switch over, the standby CSM-S fails to initialize and the new standby supervisor engine prints the following message for all CSM-S ports:
    %PM-STDBY-4-INT_FAILUP:GigabitEthernet7/2 failed to come up.No internal VLAN available

  • What happened to the Toshiba Qosmio x505??

    What happened to the Toshiba Qosmio x505?
    I have the x300 17" and I love it but need to upgrade.
    It was on the website for  a week for a preorder and then it was gone and hasn't come back I was thinking of getting it from BB but now its gone.
    Where is it,is it coming back and when?   I think its one of the best  18.4" Laptops out there overall. 

    Yeah, it really sucks.. The best laptop I can find at BB is the HP i7 for $1299.. Which has a really crappy trackpad and only a nvidia 230.. It was the *only* i7 cpu w/ 17"+ at my local BB.. I signed up for a $5000 BB card just to buy a new laptop, and now I can't find one I like. I'd buy the toshiba 505 in a heartbeat. Newbegg has them in stock, so if the toshiba doesn't appear at BB in the next couple weeks or so, I'm just gonna cancel this new BB card and buy it from newbegg, they have a 12mo 0% interest deal going on now too.

  • What Happened 2 the Call Monitor

    Hello Other Sykpe Users-- What happened 2 the call monitor that used 2 let U know exactly how much credit U have left while U R talking.  With the new system, I have been cut off 3 times without any warning--I don't like the new system.  Do I have a choice so that I can use the call monitor???   Please help with this subject.  I could not find any such question on the public board.  Thanks for UR help.   JCP

    Hello Claudius--thank U for this suggestion.  I am aware of auto credit; however, I found the previous model much more useful 2 me than the current one.  Unfortunately, my relatives do not have access 2 SKYPE & therefore, I have 2 call their cellphones.  I even tried a subscription, but with that method, if U use up UR credit U have 2 wait until 30 days has passed 2 renew the sub-scription.  In the meantime, U have 2 pay full price 2 get as-U-go credit.  All this dilema could B solved if SKYPE would just return 2 the previous format.  Perhaps this post will encourage other users 2 start a thread requesting that SKYPE reverse this part of the new format.  Again, thanks 4 UR suggestion--at least I found out that I do understand how the system works.  I just don't like the current format; therefore, I will revert 2 using calling cards which R much cheaper as long as I use the full amount all at once.  JCP

  • What happens to the open item in bsid table when it is cleared

    hi experts,
                   i have a doubt about open and cleared items of accounting documents. as we know open items of customers are stored in bsid and cleared ones in bsad. For suupose, an open item is closed ina particular period then what happened to the entry in bsid and bsad table. an entry regarding is stored in bsad (cleared),and what happens to the entry in bsid, still it will be there or removed from it.

    Hi,
    When ever we clear the document(Complete payment) that document will be moved to BSAD table. Other wise it will remain in BSID.
    If u are making partial payment then all the partial payment documents along with original document will be stored in BSID till u made the complete payment for that invoice.
    Assumption is u have to give all partial payment documents made for particular invoice item while u are making complete payment in F-28 transaction. So that these partail payment documents will also be cleared while making complete payment and moved to BSAD table.
    This trasaction can be used for both partial and complete payments.
    Irrespective of complete or partial payments made all the documents will remain stored in BKPF and BSEG tables.
    BSID and BSAD are index tables to address performance issues with BKPF and BSEG tables.
    So all open and cleared documents will be there in BKPF and BSEG tables.
    All cleared documents will be there in BSAD table.
    Alll open documents will be there in BSID table.
    Hope it is clear.
    Thanks,
    Vinod.

  • What happens to the mail in my iMac after I delete it from my iPhone? Will it be deleted from my computer as well?

    What happens to the mail in my iMac after I delete it from my iPhone? Will it be deleted from my computer as well?

    If they are both using the same iCloud ID (assuming you are running your mail from iCloud), then yes, the email will disappear from your Mac after you delete it from your phone and after your phone sycs with iCloud and your Mac syncs with iCloud.
    I use a windows phone, but it works the same.

  • Just upgraded to 5 from 3 - what happened to the page select icon? Can't find it in customize toolbars.

    Used to be you could select which page you wished to go back or forward to from the arrow icons on the navigation toolbar. The history menu item only shows 10 sites without having to open history for today. What happened? Is there another icon or a new plug in for this functionality? I used it all the time.

    ''what happened to the page select icon (Back/Forward)''
    The back/forward buttons have been moved to right-hand side of the navigation bar and the drop-down was removed. User right-click or hold click for one second to see the tab history. This is item #5 in my list.
    The History menu also has "Open Previous session" and "Open closed windows",
    to see more history use the History sidebar ("Ctrl+H") or the History Library List ("Ctrl+Shift+H") and sort or view by "Last visited".
    You can make '''Firefox 5.0.1''' look like Firefox 3.6.19, see numbered items 1-10 in the following topic [http://dmcritchie.mvps.org/firefox/firefox-problems.htm#fx4interface Fix Firefox 4.0 toolbar user interface, problems (Make Firefox 5.0.1, or 4.0.1, look like 3.6.*)]. ''Whether or not you make changes, you should be aware of what has changed and what you have to do to use changed or missing features.''
    * http://dmcritchie.mvps.org/firefox/firefox-problems.htm#fx4interface

  • E4X: What happens to the root element?

    I'm working with XML using the E4X notation. I'm used to the "old school" XML APIs that use DOM and I'm a bit confused.
    For example, let's consider the following XML
    <mx:XML id="myXML" >
      <top>
        <sub1 id="uno">
          <sub2>hello</sub2>
          <sub3>world</sub3>
        </sub1>
        <sub1 id="duo">
          <sub2>ok</sub2>
          <sub3>ko</sub3>
        </sub1>
      </top>
    </mx:XML>
    In my code I use the following traces. This is done with the De MonsterDebugger, but all others should work the same way. I have casted the traces to String only to make it easier to ask this question (no need post images)
    MonsterDebugger.trace(this, "myXML:" + myXML);
    MonsterDebugger.trace(this, "myXML.sub1: " + myXML.sub1);
    MonsterDebugger.trace(this, "myXML.sub1.sub2: " + myXML.sub1.sub2);
    What I get as output is
    (String) = myXML:<top>
      <sub1 id="uno">
        <sub2>hello</sub2>
        <sub3>world</sub3>
      </sub1>
      <sub1 id="duo">
        <sub2>ok</sub2>
        <sub3>ko</sub3>
      </sub1>
    </top>
    (String) = myXML.sub1: <sub1 id="uno">
      <sub2>hello</sub2>
      <sub3>world</sub3>
    </sub1>
    <sub1 id="duo">
      <sub2>ok</sub2>
      <sub3>ko</sub3>
    </sub1>
    (String) = myXML.sub1.sub2: <sub2>hello</sub2>
    <sub2>ok</sub2>
    All is fine above and this was a bit long abstract for my question. The question is what happens to the root element, in this case <top>? I was trying to access the data with the following notation
    myXML.top.sub1; // etc
    I spent quite a lot of time trying to get it to work, until I discovered that the root element is not used. Can anyone explain this?
    Or, I guess the simple explanation is that the root node is ignored and the sub nodes are created as properties of the object. The question also could be stated as: Why isn't this documented in the Flex API Reference?
    Thanks.
    P.S. I found this article on common E4X pitfalls which also has other interesting topics when working with E4X.

    its gone
    downgrading would kill the phone..

Maybe you are looking for