What happen when SSL daughter card fails?

I'm using two CSM with SSL duaghter card with redundancy.
What happen if the card fails? CSM fails too?
Thanks.
Andrea

When the SSL daughter card failure is detected, the SSL daughter card is restarted causing all SSL flows to fail, and they will need to be re-established.
During a supervisor engine switch over, the standby CSM-S fails to initialize and the new standby supervisor engine prints the following message for all CSM-S ports:
%PM-STDBY-4-INT_FAILUP:GigabitEthernet7/2 failed to come up.No internal VLAN available

Similar Messages

What happens when HTTPS communication fails during certificate check?

Hello Experts,
I have a scenario where a Bapi functionality(server proxy) is exposed as a webservice .
So scenario will be SOAP -> XI -> Proxy (calls a BAPI)
Here we are going to use HTTPS (SSL).
I would like to know :
What happens when a check for certificate validation fails in XI? It may be due to invalid certificate, expired certificate or a request from unauthorised user-
- Will it be raised as a exception and we need to do some configuration to inform it back to Sender?
- Will the message fail in Moni with red flag ?
- Alerts will be created ?
Please share your experiences and expert sugestions.
Thanks in Advance!!
Regards,
XI Queries.

Hi Abhishek,
Thanks for the reply. I will keep this in mind and design the scenario & error handling accordingly.
Appropriate points awarded
Kind regards,
Xi Queries.

VDI3: what happens when the Primary VDI core fails?

A potential customer asked me this and I did not really know how to answer the question ... sorry if this was asked before. So here we go:
What happens when and if the Primary VDI core fails? Will the entire VDI3 setup go down? Will running sessions be lost? And how do you fix that?
I found this page:
http://wikis.sun.com/display/VDI3/MySQL+Cluster+Reconfiguration+Scenarios
So I assume the "Non-VDI host ==> Primary Management Host" scenario is what would need to be done?
http://wikis.sun.com/display/VDI3/MySQL+Cluster+Reconfiguration+Scenarios#MySQLClusterReconfigurationScenarios-NonVdiToPrimary
If this is correct then this would answer the "how do you fix that?" part. OK then.
But still I'd welcome if anyone could explain what exactly would happen when and if a Primary VDI core fails. The customer's opinion on this is that they are a "single point of failure" because the Primary VDI host is not redundant (as opposed to the 2 x Secondary VDI cores) ... So, is this assumption correct or not?
Thanks in advance.

Hi,
Assuming you have 3 VDI core hosts. One of them is the primary. And the primary goes down. So what happens then:
* The underlying database is still running on the remaining hosts
* All desktop sessions are still running on the remaining hosts
* New session requests will be handled by the remaining hosts.
* All desktops are still running on the virtualization hosts.
So in essence, your VDI cluster is still healthy. The operation is just impacted in this way:
* You can't add new VDI core hosts
* You can't change the configuration of the Sun Ray server failover group
* A failure of another VDI core host (data node) will result into a complete outage of the underlying database
You should bring up the primary again as soon as possible in order to gain failover capabilities again.
-Dirk

What happens when CTAS fails?

Hi,what happens when CTAS fails?
Will the table be created with as much data as it fetched before the error occurred.

Just try it and you will see:
1 create table test_table as
2 select rownum/(case rownum when 5 then 0 else 5 end) as rn
3 from dual
4* connect by level < 10
SQL> /
select rownum/(case rownum when 5 then 0 else 5 end) as rn
ERROR at line 2:
ORA-01476: divisor is equal to zero
SQL> desc test_table
ERROR:
ORA-04043: object test_table does not exist
SQL>

What happens when secondary fails ?

In 8.1 HTTP session replication.
          What happens when, in the middle of a user session, the secondary fails ?
          Does the primary automatically pick another secondary and update that ?
          -Anu


Goodmorning Gary.
From ACS 5.3 release notes.
View Log Message Recovery
ACS 5.3 provides a new feature to recover any logs that are missed when the view is down. ACS collects these missed logs and stores them in its database.
Using this feature, you can retrieve the missed logs from the ACS database to the view database after the view is up.
To use this feature, you must set the Log Message Recovery Configuration as on. For more details on configuring the View Log Message Recovery, see User Guide for Cisco Secure Access Control System 5.3.
This feature must be enabled, under Monitoring and Reports, Launch Monitoring & Report Viewer. Successivamente Monitoring Configuration, System Operations e Log Message Recovery.
Enable “Log to Local Target” for categories under System Administration > Configuration > Log Configuration > Logging Categories > Global.
Hope this helps.
Regards.
Andrea

What happen when sy-subrc fails

Hi,
I want to know that what happens when sy-subrc fails . is there any example for it.

Hi,
Its a system variable which is used to check whether a particular stmt was successful or not.
The purpose of this field to indicate success/failure of any action in SAP. After each statement in SAP is executed, the SY-SUBRC is set depending on the result of the statement. the SY-SUBRC can contain the following values.
0 - This value is set when the statement is executed successfully.
2 - This value is set when the statement is executed unsuccessfully.
4 - This value is set when the statement is executed unsuccessfully.
8 - This value is set when the statement is executed unsuccessfully.
12 - Specified object not maintained in the user master record.
16 - No profile entered in the user master record.
24 - The field names of the check call do not match those of an authorization. Either the authorization or the call is incorrect.
28 -Incorrect structure for user master record.
32 - Incorrect structure for user master record.
36 - Incorrect structure for user master record.
For more deatils please go through the link [http://help.sap.com/saphelp_47x200/helpdata/en/7b/fb96c8882811d295a90000e8353423/content.htm]

What happened to my gift card credit?

I know how to review my purchase history in my iTunes account. But, how do I find out what happened to a gift card credit? Per my my account's purchase history, I only used $10 of a $50 gift card (assuming the culprit is NOT user error, e.g., I redeemed on the incorrect account). Can I search "payment history" in addition to purchase history? Thanks.

I am currently in 'discussion' with iTunes about this very issue. It's happened to me at least twice before when I redeemed a Gift card and didn't use the full amount. A couple of weeks later... the 'credit' was gone!
I also question as to why iTunes do NOT show gift card redemptions... VERY sus imho!!! Why dont they??!!
I have asked iTunes to provide me with a list of all my transactions for this year so I can see when, where and how my credits were used. So far the best I got was "check your account balance". They have said they will look into it from another side (ie. not via their customer support) but I will give them a week before I go to Fair Trading and make a formal complaint.
I have provided them screen shots, dates, my purchase history etc. and the numbers just dont add up. Either my credit balance expired (in the space of a couple of weeks) or someone is skimming accounts - which is on the iTunes system. Either way iTunes have a case to answer!

What happens when the multiply effect is applied to both the object and the graphic within?

Hi everyone,
I could really use some help with this...
I'm getting a booklet ready to be printed. Originally, half of the pages were to be printed on paper with a (physical) colour. For budget reasons however, I've now decided to print the paper colour, and have the content of the pages overprinted on the tint in the background, which I've applied to the pages in the background of an additional master page.
When I set the objects to multiply, they blend with the background colour, which is the effect I'm looking for, as there would be no 'paper white' on the pages that I want to appear as though printed on coloured paper.
There's something confusing me though; you can also set the graphic within the object frame to multiply. This makes the graphic appear darker, which I don't really understand, since there is no extra colour within the graphic that accounts for this. I've looked at the output in the resulting pdf, and it looks like it's not just an on-screen effect, but the extra amount of (in this case) yellow would also be visible in the printed result.
Does anyone have an explanation for this? Please see the graphic for a visual example.
Thanks in advance, kind regards
Robbin

Hi.
          Yes. There is a heartbeat mechanism between all cluster members so they detect when a
          member has left the cluster. The primary server recognizes when it's secondary server
          has failed, and then proceeds to search for another member of the cluster to make as
          it's new secondary.
          Regards,
          Michael
          David Whitehouse wrote:
          > I'm trying to figure out what happens when the server holding the replicated state
          > for an object fails.
          > Does the server with the primary object (or the replica-aware stub) recognize
          > the failure and select a new
          > server to hold the replicated state?
          >
          > For instance, Assume I have a cluster defined with three servers - 1,2,3 - with
          > an instance of object A on server 1
          > and the replicated state ino on server 2. What happens if server 2 fails? Is the
          > state now replicated to server 3?
          >
          > Thanks, David
          Michael Young
          Developer Relations Engineer
          BEA Support

What happens when you cant login or anything on itunes?

It wont let me login to anything redeem cards open anything!

What happens when you try to login? Error messages?

NTP not working on the SSL Daughter Card

Hello,
We are having an issue with NTP with the CSM SSL module (CSM-S). If we set our management router as the ntp server on the SSL daughter card, after a while it becomes unsynchronized.
If I set up the server it initially looks like this on the daughter card:
ddbusxl916(config)#ntp server 10.2.69.1 prefer
ddbusxl916(config)#^Z
ddbusxl916#sh run | include ntp
ntp server 10.2.69.1 prefer
ddbusxl916#sh ntp status
Clock is synchronized, stratum 4, reference is 10.2.69.1
nominal freq is 250.0000 Hz, actual freq is 250.0000 Hz, precision is 2**24
reference time is C8D48C72.3DB84313 (08:53:06.241 UTC Mon Oct 9 2006)
clock offset is -0.0056 msec, root delay is 258.48 msec
root dispersion is 16281.88 msec, peer dispersion is 15875.02 msec
It also shows that the device is synced with master:
ddbusxl916#sh ntp associations
address ref clock st when poll reach delay offset disp
*~10.2.69.1 10.244.15.1 3 0 64 377 1.0 0.16 0.1
* master (synced), # master (unsynced), + selected, - candidate, ~ configured
Now after a couple of minutes if I look again I see:
ddbusxl916#sh ntp stat
Clock is unsynchronized, stratum 16, no reference clock
nominal freq is 250.0000 Hz, actual freq is 250.0000 Hz, precision is 2**24
reference time is C8D49200.DC73366F (09:16:48.861 UTC Mon Oct 9 2006)
clock offset is -612.3787 msec, root delay is 614.12 msec
root dispersion is 16527.33 msec, peer dispersion is 16000.00 msec
Although the router 10.2.69.1 is still set up as the master but no more synced:
ddbusxl916#sh ntp associations
address ref clock st when poll reach delay offset disp
~10.2.69.1 10.244.15.1 3 46 64 0 1.1 -619.9 16000.
* master (synced), # master (unsynced), + selected, - candidate, ~ configured
Thanks in advance for any information you would like to share.
Cheers,
Murtaza

chek this configuration guide
http://www.cisco.com/en/US/products/hw/modules/ps2706/products_configuration_example09186a0080216c16.shtml

What Happens when u kill a backgroud process

What Happens when u kill a backgroud process?
such as kill- 9 ora_smon
Will the oracle automatically perform recovery???
will the database startup?

If you want to face what actually will happen, just make it on test environment (test db).
Then check your db status, instance will be abort.
Do you know what SMON`s purpose ?
If you_dont_know then
make it; (ps -ef | grep smon take PID, then kill -9 PID);
end if;
SMON - System Monitor process recovers after instance failure and monitors temporary segments and extents. SMON in a non-failed instance can also perform failed instance recovery for other failed RAC instance.
Here you can read about Oracle background processes:
http://www.dba-oracle.com/t_background_processes.htm
and
http://download.oracle.com/docs/cd/B10500_01/server.920/a96524/c09procs.htm

What happen when an Expense report is approved or rejected ?

Hi All,
I would like to know what happens when an Expense report is approved or rejected.
What is the process flow and once approved how the reimbursement is processed.
Thanks & Regards,
Ajay Sharma

Hi,
a parameter, that is set higher "than allowed" is NEVER replaced by any substitution value !!!
=> if it is correct, it will work - otherwise the system might not drive up or fail otherwise ...
Unfortunately, there are MANY parameters, where you should use values, that are "not allowed" and even a lot of parameters, that are totally unknown - all of them work as you set them ... hopefully with useful values ...
9000 in this case is recommended in nearly every GoingLiveCheck by SAP )
Regards
Volker Gueldenpfennig, consolut international ag
http://www.consolut.de - http://www.4soi.de - http://www.easymarketplace.de

What happens when an iPod is synchronized with an iTunes library that is bigger than the available space on the iPod?

What happens when an iPod is synchronized with an iTunes library that is bigger than the available space on the iPod? I did this some time ago. On screen was shown available space somewhat less than 120 GB, but maybe somewhere between 10 and 20 GB more in the library. I had to get the iPod updated anyway, so I did proceed. However, afterwards the total content of the library was only about 110 GB. Now I wonder what did actually happen. Was the first sign only corrected for double copies of the same files or lost files or where files deleted from iTunes? And if files where deleted from iTunes, were they also deleted from my computer?

Same as you would if you bought a pc; copy everything from your old computer to your new one. Then you can just sync everything from the new computer, as you did with the old one.

What happens when multiple users access the same servlet?

Do the users share all the same resources? Or is a new process generated for each user? I have a servlet that builds a string to return to the user and I only have myself to test, so I can't really see what happens when many users access the servlet. Is there a possibility that the string will get screwed up, like when dealing with multiple threads, or do all the users get their own resources and I don't have to worry about that?

huh? if you can point a test servlet at it, you can point a browser at it (even if the servlet does not serve html it will run)
try pasting the servlet URL into a web browser
refreshing multiple browsers repeatedly could provide a manual test

I want to change my Apple ID because I have a new email address, but what happens when someone tries to facetime me using my old Apple ID?

I want to change my Apple ID because I have a new email address, but what happens when someone tries to facetime me using my old Apple ID? Will they still be able to contact me on facetime using my old Apple ID?

Not if you change the ID. You would need to give them the new address.

What happen when SSL daughter card fails?

Similar Messages

Maybe you are looking for