What happened to my airport extreme that airport utility says used to be part of my network but no longer is found?

I have been working on regaining wireless printing from my MacBook and just discovered something new to me. I brought up Airport Utility and received a screen display showing my network. The diagram box for the Airport Extreme has a warning icon and clicking on the diagram box for the Airport Extreme brings up the message that my airport extreme cannot be found and that it USED TO BE part of my network. The only help given is to check the device and make sure it is plugged into power, within range and connected to the Internet. Its been a long time since I last set up the Airport Extreme, but it is powered up, in the same place and connected to my cable modem as before. I continue to have wireless connection to the Internet from my MacBook and iPhone. What I do not have is wireless connection from the the MacBook to my Brother Printer as I did until, for unknown reasons, it stopped working.
So far, I have checked all the help for the printer problem and wonder if my problem is in the Airport Extreme? The printer does find the Airport Extreme, but still does not print wirelessly, only by attaching it with USB cable to the MacBook.
Resetting the Airport Extreme will wipe out that setup, but should I do this anyway? Might it help the printer problem.
Thanks for your help. I've worked on this a long time using available material.

I see now that long questions are not going to be read and answered. Understandable. Since writing this I got help on one aspect of question and now have Airport Extreme visible through Airport Utility and it seems to work. However the wireless printer still does print. On the printer's screen, it recognizes my wireless network and connects. When I try to print from the MacBook, the usual printer icon comes up, but with Printer is Offline. Printer is Not Connected. So far, nothing in Apple or Brother help has given me answer to this problem. Any ideas would be appreciated.

Similar Messages

Is there any way to set up an Airport Extreme that had been previously used in a password protected network and the password was not provided by the seller ?

Background -
My original Airport Extreme Base Station failed (would not connect to the modem). I purchased a similar, if not identical base station on eBay. Unfortunately, the purchased base station apparently was used in a password protected network. For what it is worth, my son gave me a Netgear wireless router, but it leaves a lot to be desired. For one thing, I use to keep the cable modem in the basement along with the Airport base station, with a printer connected to the USB port. The Netgear device does not have a USB port and also requires that the computer (in this case, the eMac) used to set up the network be connected to one of the ethernet ports. This meant I had to move the cable modem and router into my bedroom, a very undesirable situation. It then occurred to me that the original Airport base station Wi-Fi function might still work, and tested this hypothesis and sure enough, the Wi-Fi function does indeed work I currently have both base stations powered on, with my printer connected to the original. Both base stations appear under my Network icon, but neither Airport Utility 5.4.2 or Airport Administrator Utility 4.2 see either base station. I can select the original base station as my network, connect to the printer or even my other computers, but as soon as I try to select the new one, it asks for the password. I would like to somehow reset this base station and then redefine the network name and encryption.

I would suggest that you perform a "soft" reset on the AirPort Extreme Base Station (AEBS) that you just got from eBay. This type of reset will temporarily (5 minutes) disable both the base station and wireless security passwords so that you can access it with the AIrPort Utility to make the necessary changes.

Installed airport extreme OK, netwk utility says it's not 802.11n

Installed new Airport Extreme without problems. Mac has 2GHz Intel (iMac 4,1), so it should be capable of 802.11n. Network Utility shows (802.11 a/b/g) under Interface (en1). Should this not be 802.11n? How do I know I'm using 802.11n?

Hi
What you see under the e1 interface is what the Airport card can have as WiFi
if you only see 802.11 a/b/g then it would mean that your imac is not 802.11n
able. You should be able to read something like
Wireless Network Adapter (802.11 a/b/g/n)
and linkspeed 300 Mbit/s if you have n

I'm trying to stack an airport express to my extreme it shows that its part of the network but the express still flashes amber what to do please help

I'm trying to stack a new airport express to my airport exteme to extend the range to the other side of my house on the utility it recognizes it as part of the network but the express still flashes amber. what to do please help

Open AirPort Utility and click on the amber dot next next to the AirPort Express.
If you see an Update button click it.
Otherwise look at the information next to Status and click again on the smaller amber dot there. A window will open to explain why the AirPort Express is not happy along with some suggestions to remedy the "issue".

I have a Airport Extreme that is dropping the wireless signal alot (several times a day). The green light will go amber but the internet service (ethernet cable) will still be fine. The wireless icon on devices with go away.

I have a Airport Extreme that is dropping the wireless signal alot (several times a day) The green light will go amber, but the internet service is still ok if your using an ethernet cable directly plugged in. When the light goes amber all devices that is using wireless will lose there wireless icon. The only way to get the green light back is to unplug the Airport device and replug it back in. I tried the reset on the back but still no luck. What is the fix?

Let's see if I can get this straight.
You have an Airport Extreme base station that is set to "Create a wireless network" and you have the box checked for "allow this network to be extended"....
Then you have an Airport Express that is set to "Extend a wireless network" which you selected the name of your network in the box...
Correct?
See this Apple document:
http://support.apple.com/kb/HT4259?viewlocale=en_US&locale=en_US
The wireless unit on the right of the diagram can be either of the newer Apple base stations.
Extreme, Express, Time Capsule

HT1226 how to add security key to airport extreme that was set up without? a key?

How can I add a security to my airport extreme that was set up without one?

ArmlockU wrote:
Will have to have re-set up my airport express or will the extreme just work with the express? I have the express locked down and I thought about unlocking the express? What would I do to set this up? Any help I would greatly appreciate it!!!
You should set up the Extreme as your main router and eventually the Express to stream music or to extend the wireless.
After the Extreme is set up and running, just set the Express e.g. to "Join a wireless network".
Alternatively reset the Express to factory default (see manual) and configure it from the scratch to your needs.
Lupunus

My airport extreme (new-5th gen) connects to my iMac - and a PC laptop but will not connect to the internet, my ISP says that I have entered the correct modem ID and that I contact Apple supt as they do not support airport extreme...??

Any suggestions getting my modem (Speedstream 5200) talking to my new airport extreme? Airport Extreme says I do not have the correct user password for the modem but my IP provider says that I do and that they (Bell Sympatico) do not - in any case - support Airport Extreme and that I should talk to Apple Support...who do not come to the phone. So my computers see my new network and my Airport Extreme sees my computers but it cannot access the modem and therefore the internet. Any ideas?

The user manual for the Speedstream 5200 indicatest that it is a router....see link below.
http://www2.windstream.net/downloads/links/SpeedStream211.pdf
If the Speedstream is acting as a router, then the AirPort Extreme must be configured in Bridge Mode to avoid having two routers in series on your network....which would certainly cause IP address conflicts and connection issues.
To configure the AirPort Extreme in Bridge Mode.....
Open AirPort Utility - Click Manual Setup
Click the Internet icon
Connection Sharing = Off (Bridge Mode)
Update

I have an airport extreme and express, if I use the extreme as a base station connected to my old router can I use the express to extend the signal while also creating a new network that only I can use?

I have an airport extreme and express, if I use the extreme as a base station connected to my old router can I use the express to extend the signal while also creating a new network that only I can use? Essentially having two wifi connection off the same network? If so how do I set this up?

Extending using a wireless connection always results in a performance compromise.
If the Express is going to extend using a wireless connection, then the Express will need to be located about half way between the AirPort Extreme and the general area where you need more wireless coverage. The more that you have line-of-sight between the Extreme and Express, the better the network will operate.
Remember......the Express can only "extend" the quality and signal speed that it receives, so it needs to be located where it can get a very good signal from the Extreme. Although Apple cleverly uses the term "extend", a more accurate term for the Express would be "repeater".
If the Express will extend by connecting to the Extreme using a permanent, wired Ethernet cable connection......highly recommended for best performance.....then the Express can be located exactly where you need more wireless coverage. There is no signal loss at all through the Ethernet cable, so the Express gets a full speed signal no matter where it might be located.
Post back to let us know which way to you want to go.

Is it possible to set up a network with airport extreme that is not on the internet

Is it possible to set up a home network using airport extreme that will be a non-internet option? Not connected to the internet wifi.

Is it possible to set up a home network using airport extreme that will be a non-internet option?
Yes
Not connected to the internet wifi.
If the AirPort Exteme is not connected to the Internet, then Internet connections will not be available on wireless or wired connections.

I have an old Airport Extreme that I want to password protect. I being told that Airport Utility 5.6 is needed to manage the base station. When I download it and try to install that utility I told that it is not compatible with OS X 10.7.4

I have an old Airport Extreme that I want to password protect. I being told that Airport Utility 5.6 is needed to manage the base station. When I download it and try to install that utility I told that it is not compatible with OS X 10.7.4

The odds are that you downloaded AirPort Utility 5.6.1.....which will only work with Leopard and Snow Leopard Macs.
Since your post indicates that you are using Lion 10.7.4, you need the correct utility for Lion. The link is below:
AirPort Utility 5.6 for Mac OS X Lion

I have a new Airport Extreme that works great with my IMac but keeps dropping out on our Windows 7 PC. I have tried all 11 2.4 Ghz channels and they all have dropout issues. Any suggestions?

I have a new Airport Extreme that works great with my IMac but keeps dropping out on our Windows 7 PC. I have tried all 11 2.4 Ghz channels and they all have dropout issues. Any suggestions?

Hello sstefanik
Check out the articles below to troubleshoot your issues with getting a proper connection with Wi-FI. Try creating a new Network Location and join your network to see if you can get on that way.
Wi-Fi: How to troubleshoot Wi-Fi connectivity
http://support.apple.com/kb/HT4628
Using network locations (Mac OS X v10.6 and later)
http://support.apple.com/kb/ht5289
Regards,
-Norm G.

How can i enable the airport extreme that is built-in on my mac mini model 2010

I need some help in how can I enable the airport extreme that is built-in my mac mini 2010 model ? I tried and download the airport extreme 802.11n enabler for mac and it tells me Your computer does not meet the hardware requirements for this update. please help me

Wireless is already enabled. Just turn it on using the Finder's menubar icon or using Network preferences.

I am a bit of a ludite, I have an airport extreme that is requesting an update, this requires a password which geek squad never gave me, any advice , can I reset that password or must I pay someones piper? Thanks for any help.

I am a bit of a ludite, I have an airport extreme that is requesting an update, this requires a password which geek squad never gave me, any advice , can I reset that password or must I pay someones piper? Thanks for any help.

Hello:
The password should be your administrator password.
Barry

Just bought a new Airport Extreme BS. After setup my iphone4 won't find the network (not even with manual entries), but my iMac (2009) does. What is wrong?

Just bought a new Airport Extreme BS. After setup my iphone4 won't find the network (not even with manual entries), but my iMac (2009) does. What is wrong?

Well, after another call with Apple support and the engineers, no success. After spending over 20 hours trying to debug this, I give up. Apple was basically fishing for a solution with trial-and-error settings on the iphone. Then they wanted me to plug in software to log my iphone connections to the router, etc, etc., etc., at which point I decided I no longer wanted to participate in their testing process and will simply return the router.
25 hours of my life I'll never get back.
Big bummer, and frustrating for all the obvious reasons.

I have a new Airport Extreme that works well with my IMac but is intermittent with our Windows 7 PC. Any ideas?

I have a new Airport Extreme that works well with my IMac but is intermittent with our Windows 7 PC. Any ideas?

Thanks planb77. Your instructions worked but I had to do a little more than you stated. I did not realize that transferring files to a new computer was not enough. When the iPod synced I was told I needed to "authorize" my new computer to get my iTunes purchases to sync to the iPod. So after the initial sync, I ejected and disconnected the iPod, went into the iTunes store, set up "home sharing" and then authorized the new computer. When that was done I reconnected the iPod and was able to sync all my books and music. The only thing I couldn't do was rename the iPod as iTunes never asked me to. Is there a way to rename it after it has been set by iTunes as "owner's iPod"?

What happened to my airport extreme that airport utility says used to be part of my network but no longer is found?

Similar Messages

Maybe you are looking for