What is causing my print jobs to fail?

Having trouble printing documents (which range from 12-50 pages) from InDesign CC. Whole job fails to print. Started with new documents based on template created in CC. Trouble fonts have been removed from styles. I can print some individual pages. On the problem pages I have had luck printing them without the images, but other pages with no problems have similar images on them in terms of size, file type, color space, etc. Tried exporting to IDML, still had trouble printing.

HI, JonJamesDufort
You might try to save a copy of the file to help troubleshoot the Indesign printing in case if you have to remove other images.
Have you tried to export to pdf or Print to pdf if you have Acrobat installed? If you can export to PDF from Indesign, then I would look to see if you have linked images that could be causing the problem. Does the print job just fail? Also what kind of printer are you trying to print to? You might have a corrupt image or graphic that could be causing the print job to fail. Do you have any older eps graphics that you are including in your file? Look to see what files are linked and try to embed the files. Did you run a preflight on the file? You should do that first to give you an idea of what could be causing it.
If you can export to PDF and then Print to your printer, then you have a work around to get your file printed.
If you find that this resolves your issue or was helpful, could you please take a moment to come back to this discussion and mark the post as helpful. Doing so greatly benefits your fellow users
Let me know if you have any questions
Thanks
Scott V

Similar Messages

What would cause my printer to only print about 3/4 of a 4x6 photo on a C4795?

What would cause my printer to only print about 3/4 of a 4x6 photo on a C4795?

eee! So many posts.
I currently have 2 harddrives hooked up. One has about 37.56 Gigs left on it (probably just over 3/4 full) and the other is nearly full. My files are saved onto it. I am editing in DV format and everything is rendered.
I have a drive allocated as the scratch disk.
I don't believe the drive is going to sleep. I would think it would effect my audio as well, since they are both located on the same drive.
For what it's worth, I ended up ejecting the drive I was using as I needed to do some other work and my system seemed to speed back up. I reopened Final Cut with and it's like my system isn't bogged down anymore. I may try capturing to tape using a different drive and see if maybe it was the drive itself that was bogging down my system.

Photoshop CS4 for Mac What can cause the error: Plug-in failed to load - NO VERSION

With Photoshop CS4 for Mac I install the Kodak Plug-in DIGITAL GEM Airbrush Professional v2.1.0. When Photoshop starts I get an error:
Plug-ins that failed to load:
   DIGITAL GEM Airbrush Professional v2.1.0 NO VERSION - - from the file “DigitalAIRProv2.plugin”Flash:
   Connections
   Kuler
This plug-in works fine on my Mac Pro with Photoshop CS4 and OS 10.6 but fails on a new Macbook Air.
Reinstalling the plug-in did not make any difference. What can cause this error?

Thanks Chris, That was my first thought too but this same plug-in works on another installation of CS4. This is a Mac installation and the plug-in is Universal so it should work. Is there any other possible cause for this error? Would Photoshop refuse to load a plug-in in a low memory situation?
Also, The Flash extensions:Connections and Kuler are working OK, I just copied a little more out of the System Info report than I needed to.

What would cause the printer to only print text in microsoft word but no images

i have a hp deskjet D1320 printer, windows xp operating system, and i have always printed greeting cards from microsoft word by inserting an image and then printing it with the printer set to duplex(2sided)printing option, so after you print the image you flip the card around and then print the text on the inside of the card. now the printer does not print any images when i insert the image and then click print it just runs 1 piece of paper through the printer and stops but it will still print text just fine, does anyone know what would cause this type of an issue?
thank-you,
hwnugent

Hi there hwnugent,
Try downloading and running the print and scan doctor located here:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03275041&cc=us&dlc=en&lc=en
It can fix a lot on its own and if not give a better idea of what is going on. Let us know the results.
Best of Luck!
You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

CUPS print job options fail when called from lp (UNIX command line)

Under Leopard this command-line print request fails to respect the specified job options:
lp -o number-up=2 -o page-border=double <filename>
Though it worked great in Tiger, the number-up and page-border job options are now disregarded. I have tried lots of things (and wasted lots of paper) such as setting them permanently with lpoptions (and they do appear changed when the lpoptions command is repeated), using lpr instead of lp, reinstalling the printer via the CUPS localhost web interface, enabling non-Bonjour scanning with the hack to the CUPS preference file, deselecting "Last Printer Used" for the default printer in the System Preferences -- nope.
I have not tried other job options; I assume that whatever is breaking these two is breaking all the others, and even if it isn't, these two are what I want.
Is something new in Leopard overriding lpoptions job options? How do I make it stop? It is sooooo aggravating when something that used to work fine breaks. The printer is an HP LaserJet 4000N connected by Ethernet and discovered with AppleTalk.
Thanks for any advice!

Thanks John, I did search but somehow missed that thread.
However it did not help. With or without the "-p printername" argument lpoptions does make a persistent change to its own data:
+$ lpoptions+
+media=Letter sides=one-sided finishings=3 copies=1 job-hold-until=no-hold job-priority=50 number-up=2 auth-info-required=none job-sheets=none,none printer-info=Barrow printer-is-accepting-jobs=1 printer-is-shared=0 printer-location='Local Zone' printer-make-and-model='HP LaserJet 4000 Series' printer-state=3 printer-state-change-time=1209495301 printer-state-reasons=none printer-type=2134228 page-border=double+
You can see that the printer "Barrow" has remembered "number-up=2" and "page-border=double". Regardless if I give any of these commands:
+lpr <filename>+
+lpr -P Barrow <filename>+
+lp <filename>+
+lp -d Barrow <filename>+
none of them show the results of these option settings (and somewhere in the forest another tree is cut down).

What could cause a printer to print in Landscape but not in Portrait mode?

Hello gurus,
We recently migrated our application from windows to linux. Specs are as follows
OS: RHEL 6
DB: 11.2.0.3
App: 12.1.3
Upon testing it was noticed that Oracle Applications successfully prints output files if they are in landscape mode but no output is received at the printer if the output is of portrait type.
The request ids show status 'Completed Normal' in both the cases.
Also printing directly from linux results in successful prints for both landscape and portrait.
The same issue exists when defining type as '--PASTA Universal Printer Type' or 'HPLJ4'
Any idea what files or settings could be causing this behaviour?

Tier1DBA wrote:
Hello gurus,
We recently migrated our application from windows to linux. Specs are as follows
OS: RHEL 6
DB: 11.2.0.3
App: 12.1.3
Upon testing it was noticed that Oracle Applications successfully prints output files if they are in landscape mode but no output is received at the printer if the output is of portrait type.
The request ids show status 'Completed Normal' in both the cases.
Also printing directly from linux results in successful prints for both landscape and portrait.
The same issue exists when defining type as '--PASTA Universal Printer Type' or 'HPLJ4'
Any idea what files or settings could be causing this behaviour?There is no Portrait style for the '--Pasta Universal Printer Type' [ID 1350079.1]
Pasta Overview [ID 420019.1]
Oracle Applications Character Printing [ID 112172.1]
How to Setup Pasta Quickly and Effectively [ID 356501.1]
R12.0.6+ : Oracle Application Object Library Pasta Printing Health Check Test [ID 732270.1]
https://forums.oracle.com/forums/search.jspa?threadID=&q=portrait+AND+PASTA&objID=c3&dateRange=all&userID=&numResults=15&rankBy=10001
Thanks,
Hussein

Canon MX 850 "Print job manager failed"

After recently upgrading to Snow Leopard (0S 10.6.8) my Canon MX 850 Wireless Printer has quit working. After every attempt to print I get the message:
Error: System/Library/Printers/Libraries/PrintJobMgr/Contents/MacOS/PrintJobMgr failed
I really need to get this fixed. Please help!

Pahu's response to "Canon MX860: Cannot Print from WiFi because of System/library Error" solved my problem completely. So give him 10 points from me too!

What is causing this FTP task to fail?

I use the same FTP task to connect to a local ftp site but when I try to hit another one, I get these errors: The obvious stuff like connection string, ip address and password are set up correctly because my test connection works fine. I haven't packaged
this until it works interactively. Can someone point me in the right direction?
[Connection manager "FTP Connection Manager"] Error: An error occurred in the requested FTP operation. Detailed error description: 200 Type Binary
200 Port command received
425 Unable to open the data connection
Warning: SSIS Warning Code DTS_W_MAXIMUMERRORCOUNTREACHED. The Execution method succeeded, but the number of errors raised (1) reached the maximum allowed (1); resulting in failure. This occurs when the number of errors reaches the number specified
in MaximumErrorCount. Change the MaximumErrorCount or fix the errors.

I am using VS2008 and trying this in debug mode first before I package it. When I ran the package through the scheduler, I got this more detailed error which seems to point to the connection:
Executed as user: CAMPUS\UCCTD10_SQL. Microsoft (R) SQL Server Execute Package Utility Version 10.50.2500.0 for 64-bit Copyright (C) Microsoft Corporation 2010. All rights reserved.    Started: 10:55:47 AM Error: 2014-02-20
10:57:00.36     Code: 0xC001602A     Source: Test_Adv_trac Connection manager "FTP Connection Manager"     Description: An error occurred in the requested FTP operation. Detailed error description:
200 Type Binary 200 Port command received 425 Unable to open the data connection . End Error Error: 2014-02-20 10:57:00.37     Code: 0xC002918B     Source: FTP Task FTP Task
Description: Unable to send files using "FTP Connection Manager". End Error DTExec: The package execution returned DTSER_FAILURE (1). Started: 10:55:47 AM Finished: 10:57:00 AM Elapsed: 73.274 seconds.
The package execution failed. The step failed.
My setup screen values are as follows:
Since I can't print the screen, I have all parameters set to false on the transfer screen.
Do I need to increase timeout or error values?

What will cause the FP-1000 to fail initialization?

When our Field Point FP-1000 is initialized the Network LED and the Access LED flash then go blank. The Power LED remains illuminated and the Status LED extinguishes. This has become more frequent lately. Sometimes all that is needed is to re-initialize the Field Points again and sometimes cycling the power to the Field points is required. Most of the time a re-initialization has to be repeated several times before the Network and Access LEDs remain illuminated and no Power Controller failure is reported. Once the Field Points are working the FP-1000 will stop communicating with the other modules after several minutes and the Network and Access LEDs extinguish. In this case all that is required is one re-initialization to get all of the modules on-line.
After the modules are all working and the initial failure is corrected the Field Points will operate for several hours without any failures. Then the same Power Controller Failure will pop up. As before all that is required is to execute a re-initialize to get the modules back on-line.
We have replaced all of the Field Point modules several months ago for the same problem and the new units only occasionally faulted until the last couple of weeks. Now the failures are every time the modules are powered up.
Are the Field Point units susceptible to corrosion when exposed to high humidity? We operate near the ocean, about 50 feet, but the Field Points are installed in an air conditioned trailer that once in a while will build up some moisture when the air conditioner cycles off.

FP-1000/1001 modules do not have RTlogs.
Considering that you are loosing communication with the module, but the module does not appear to be crashing from an internally recogonized failure (STATUS LED should start to flash), I would look at the communications and grounding. The FP-100X modules use the NETWORK and ACCESS LEDs to indicate when they recognize activity on the serial port (NETWORK) and when a valid command is addressed to the FP-100X or its attached modules (ACCESS). The FP-1000 uses RS-232 for data transmission. RS-232 relies on 3 primary wires; Rx, Tx, and ground. RS-232 ports are generally not isolated since they are single-ended signalling and need to share a common ground. What is the distance between the FP-1000 and the device it is attached to serially? How are both systems grounded (including power supplies)? It may be that due to the corrosive nature of seawater/salt aerosols, a portion of the system ground is at a different potential that is being charged and/or drifting over time. If you are resetting the FP-1000 by turning the power off, you may be allowing the ground to shift back to a level that allows the FP-1000 and device to communicate. Also, check the serial cable itself for broken pins/ground and corrosion.
Regards,
AaronMessage Edited by Aaron G on 04-21-2005 04:55 PM
Message Edited by Aaron G on 04-21-2005 04:55 PM
Message Edited by Aaron G on 04-21-2005 04:55 PM

What might cause 3 level tree to fail?

hi,
there are VO1,VO2,VO3.Each one has id and name fields.
i try to build a 3-level tree: VO1 is parent to VO2 which is parent to VO3
it's supposed to be a tree containing all elements of VO1 on the upper level, each leaf of which should contain all elements of VO2 etc
in order to ensure cartesian join i created a column lvl1 with value 1, and lvl2 with value 2.
then i created 2 view links between each pair: VO1 and VO2 are linked by lvl1, VO2 and VO3 are linked by lvl2.
any 2 level trees are showing ok in all combinations (between VO1/VO2, VO2/VO3)
but when i define 3 levels in tree level binding , application fails with error: (tree is kept in a region)
<UIXRegion> <_warn> Error handling viewId: /QueueAction URI: /QueueAction.jspx actual-URI: /setup.jsff.
java.lang.IllegalStateException: ADFv: Not inside container.
i follow http://andrejusb.blogspot.ru/2011/12/tuning-adf-tree-retain-view-link.html
JDev 11.1.2.3

blog helped

How can I cause HP Mobile Printing print jobs to default to duplex printing?

I purchased an HP Officejet Pro 8620 a few days ago--for use with my Windows 7 PCs. I want all print jobs to default to two-sided (i.e., duplex) printing.
I used Windows' Devices and Printers to access the printer's preferences. I selected "Two-sided (Duplex) Printing" as the Printing Shortcut. This causes all print jobs from Windows to default to two-sided printing.
(Side-point: I notice that all of the printing shortcuts have padlocks on them; if I change any of the properties, a new entry ("User Specified Print Settings") is created; I press the Cancel button to avoid creating the new entry.)
Then I opened a 10-page PDF on an Android device and printed it using HP Mobile Printing (i.e., the HP Print Service Plugin on my Android device). The plugin interface has limited print options; duplex isn't one of them. The printer did not print the PDF duplexed!
How can I cause *all* print jobs (including those from HP Mobile Printing) to default to duplex printing?

Hi,
There are several different printing solutions available for Android, such as HP's built-in print solution for Android, the HP ePrint mobile app, HP's built-in print solution for Android, etc..
As much as I aware, none will allow setting duplex printing as default, still.. mobile printing is more limited than a standard PC..
The HP plugin allow printing to a printer connected to the same local network from several apps which support the plugin, its features are limited as included in my previous link.
The HP ePrint mobie app allow printing to both a printer connected to the same network or via the cloud using the HP ePrint service to print even when the Android device is not connected to the same network as the printer.
As well there is a new 3rd party service, the Mopria Print Service which allow printing from specific apps through the local network, it should be quite similar to HP's built-in print solution for Android
The following document list different printing solutions available for Android and can be viewed as a reference:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03679829&tmp_task=useCategory&cc=us&dlc=en&lc=e...
The following document also list different prinitng solutions for Apple or Android devices and include a description of any of the options I included above:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03722645&tmp_task=setupCategory&cc=us&dlc=en&lc...
I surely do not mean to confuse you, but would like to provide you any of the options (Yes, I know, it is quite a confusing field..) and worth trying if it may allow changing the default settings, I personally not aware so it worth trying..
Hope that helps,
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

PSC 1350 all-in-one not completing print jobs wirelessly with windows 7 64 bit

I have a acer 5542 running windows 7 (64bit), connected wirelessly to an Orange Livebox hub, to which my HP PSC 1350 printer is connected (via USB cable) therefore using the Livebox as a USB printer server. This configuration has worked very well for my 2 XP laptops for the past year or two. I set up the printer on the windows 7 laptop by connecting it directly, via the USB cable, letting windows install it, and download the latest drivers, (although HP say they have no specific 64bit drivers for this printer, but the drivers they have, and that windows downloaded, work fine!) then i changed the port to the livebox ip address.
All this worked fine (as on the xp machines), I printed out a spreadsheet, which worked fine untill it approached the end of the page, then just stopped. I troubleshot the printer which didnt return any sprcifics, Just that the print job had failed, and that it had rectified the problem, then the printer starts reprinting the same document, to the same point, (about 95% complete) and again stalls, and so the cycle continues. I have tried it with various different documents and photos, to the same ends. But if i connect the laptop directly to the printer, via USB, it completes the jobs fine
I have posted on microsoft answers forums, but the one answer i have recieved (re installing everything) did not solve the problem. Although i am not too savvy on computers, i kind of get the feeling it is a spooling issue. (not processing or holding onto the last part of a print file! But its only a feeling!)
any help would be very much appreciated

Hi there,
I understand you're looking for drivers for your PSC 1210 on Windows 7. I will certainly do my best to guide you in this issue.
At this time there are no HP drivers available for this printer for Windows 7. You can still use the printer with Windows 7, you will just have to use the drivers available within Windows 7. That document will walk you through what you need to do in order to get printing again, and will also show you how to scan with this Windows driver.
Hope this helps, have a great day!!
Please click “Accept as Solution ” if you feel my post resolved your issue, as it will help others find the solution faster
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
**MissTeriLynn**
I work on behalf of HP

Have Adobe's Digital Edition, now I wanted per bookcase the books in a list printing, but printing can not activate. I cannot get it working to someway to print lists. Please tell me what the cause is that this fails or what should I change to get the lis

have Adobe's Digital Edition, now I wanted per bookcase the books in a list printing, but printing can not activate. I cannot get it working to someway to print lists. Please tell me what the cause is that this fails or what should I change to get the lists be printed

Hello, Edward and thank you for your note.
I read through the thread you mentioned and it seems that people are having a lot of problems with the iCloud clients, so we're not alone, but the unique issue in my case is the failing email address vs. the working perfectly email address.
After reading your message tonight, I tried my setup again with the preferred Apple ID (the one without the "." between the names), and for the first time ever, IT WORKS. Mail app configured the servers both send and receive as p01-smtp.mail.me.com and p01-imap.mail.me.com. For the first time, I'm able to send and receive into the Mail app, create mailboxes, move messages into and out of mailboxes, keep Sent messages, etc.
I had a 50-minute support chat with MobileMe support via ExpressLane on Monday afternoon. They couldn't resolve my issue but passed me on to escalation. I was told to expect to get an email from advanced support by this afternoon, but none has arrived. However, so far tonight -- and I will check again tomorrow several times before declaring victory -- it looks like something has been fixed on the Apple end to make things work.
I will report back after I do some additional testing tomorrow to make sure the fix is real and is solid...and before I let my friend, the new Mac user, know the good news.
Regards,
Mike

Failed with Print Job Listener - SOS

I'm using java 1.5.0.
I'm trying to monitor status of print jobs while user prints a report (in Applet viewer).
The print job listener contains 6 events:
1) printDataTransferCompleted(PrintJobEvent e)
2) printJobCanceled(PrintJobEvent e)
3) printJobCompleted(PrintJobEvent e)
4) printJobFailed(PrintJobEvent e)
5) printJobNoMoreEvents(PrintJobEvent e)
6) printJobRequiresAttention(PrintJobEvent e)
After data is transferred to printer, i can only catch the event printJobNoMoreEvents although the print job is completed or failed, or other else. And it's always like that.
In the Java Guide, they mentionned about the limitation of printing system. But i don't know where the problem comes from. Is it caused of limitation of Printing System or of Applet limitation?
If the message is not clear or you need take a look at my code, please feel free to ask me.
Can anyone comment of this issue and offer a solution or a workaround? Please help me. Thanks in advance.

My printer is shared by Domain Controller. I'm wondering the way of sharing printer whether is the problem..?

HP Laserjet utility starts and fails to go away after print job

I have an HP Laserjet 1300 hooked to an Airport base station. After the Leopard install (a default, Upgrade install from 10.4.10), I had to re-ADD that printer in the Print & FAX Preferences panel -- it wasn't simply remembered. That went fine, and printing works as expected.
EXCEPT: The HP Laserjet 1300 "utility" application (for managing the print queue) now activates with each print job -- not just when there is a problem such as "out of paper" as before. No problems are actually reported during or after the print job. And when the print job finishes, it doesn't go away. I have to manually Quit it.
I can't find any option to have the "utility" activate only when it has some problem to report (i.e., the way it worked under Tiger), or to make it go away automatically when all print jobs are finished. Any suggestions?
NOTE: When ADDing the printer in the Print & FAX utility, it did go looking for "new drivers", but didn't announce it found or installed anything new.

Thank you. That's what I was looking for:
Right click on the printer utility icon in the dock when you see it still sitting in there. Select "Auto Quit" from the pop up menu. Click on the utility to select it and open its queue window. Manually quit the utility.
After those steps it appears the utility now activates in the dock and then goes away after each print job that finishes normally.
Solved!

What is causing my print jobs to fail?

Similar Messages

Maybe you are looking for