What is Cisco Unified Computing System?

Cisco Unified Computing System (UCS) unites physical and virtual computational and network resources into a single system. UCS is a set of pre-integrated data center components that comprises blade servers, adapters, fabric interconnects, and extenders that are integrated under a common embedded management system. This approach results in far fewer system components than comparable data center platforms.

Similar Messages

Ask the Expert: Cisco Unified Computing System Director

With Andrew Nam
Welcome to the Cisco Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions about Cisco Unified Computing System (UCS) Director with Cisco expert Andrew Nam.
Cisco UCS Director was designed to operationally integrate bare-metal and virtual data center infrastructure resources to address complex, time-consuming, manual, and compartmentalized management processes. These processes burden IT organizations, preventing them from achieving business agility and efficiency. Cisco expert Andrew Nam will provide an update on installation, configuration, and troubleshooting VM provisioning process using Cisco UCS Director.
Andrew Nam is a data center solution engineer in the DC Solution team in Sydney, Australia, responsible for orchestrating the end-to-end solution support of Cisco Data Centre solutions, including Cisco UCS, Cisco Nexus architecture, VBlock/FlexPod, VDI/VXI, and cloud solutions. His areas of expertise include routing and switching, load balancer, WAN optimization, VPN, and firewalls. Andrew has worked for Cisco for more than 13 years and has 15 years of experience in the networking industry. He graduated from New South Wales University in Australia with a mechanical/manufacturing engineering degree and holds R&S CCIE 9586, VMware VPC5, and Citrix CCA - Xendesktop5 certifications.
Remember to use the rating system to let Andrew know if you have received an adequate response.
Andrew might not be able to answer each question due to the volume expected during this event. Remember that you can continue the conversation in Data Center community, sub-community, Unified Computing discussion forum shortly after the event. This event lasts through January 17, 2014. Visit this forum often to view responses to your questions and the questions of other community members.

Hi James
This Ask the Expert session may not be the right place to show you all the essential steps for how the workflow can be related to task library to achieve your initial setup flow chart, and onboarding a new client.
However, I can briefly walktthrough "Client blade Provisioning" task so it might give some idea and how you can go about.
Assumption : the infrastructure used in the following examples consists of:
- Vmware VCenter
- Cisco UCS
- NetApp ONTAP controlled storage
To be able to provision Cisco UCS blade server in automated fashion, you need to create and define the below UCS entities beforehand.
- Create UCS Organisation
- Create UUID Pool
- Create MAC Address Pool
- Create WWNN Pool
- Create WWPN Pool
- Create vHBA Templates
- Create vNIC Templates
- Create UCS Policy vHBAs
- Create UCS Policy vNICs
- Create Storage Policy
- Create Network Policy
- Create SAN Boot Policy
- Create LAN Boot Policy
Once you create all the policy above, you are good to set up a workflow container for the client blade provisoining.
1. Create UCS Service Profile
- Add a ‘Create UCS Service Profile’ workflow task and select ‘Map to User Input’ for ‘Service Profile Name’. Select the ‘Service Profile Name’ dropdown as created when the workflow container was created.
- ‘Create UCS Service Profile’ inputs. Ensure that Storage_Policy, Network_Policy, Boot_Policy_LAN and Boot_Policy_SAN entries are correct.
- Once this is done , you can move to SAN zoning.
2. Configure SAN Zoning
- In this step, a new workflow task will be created in order to configure SAN zoning. Rather than use a specific user input for this task, output variables from the previous ‘Create UCS Service Profile’ workflow task will be used as input items for this task.
- Open the workflow and search for the workflow task ‘configure san zoning’. Drag the storage workflow task into the work area and map the following user inputs.
Create Flexible Volume
- Create a ‘Create Flexible Volume’ workflow task in order to build a NetApp flexible volume and provision it for the required size.
- Once again, reconfigure the workflow such that the success criteria from the ‘Configure SAN Zoning’ workflow task proceeds to ‘Create Flexible Volume’.
Create LUN
- Using the NetApp ONTAP ‘Create LUN’ workflow task, create a LUN located within the volume created during the previous step. In order to do this, map the Volume Name user input to the output from the previous ‘Create Flexible Volume’ workflow task.
- Next, enter the LUN details, ensuring that the configured size is less than that of the volume created in the previous step.
- As before, re-map the workflow designer flow so that the successful output of the Create Flexible Volume workflow task flows into this task.
3. Create Initiator Group
- Create a ‘Create Initiator Group’ workflow task in order to build a NetApp ONTAP Initiator Group. Map the ‘Filer Identity Name’ attribute to the OUTPUT_FILER_IDENTITY output variable as supplied by the ‘Create NetApp Flexible Volume’ workflow task as created earlier in this workflow.
- Once again, modify the the workflow designer flow so that the successful output from ‘Create LUN’ flows into ‘Create Initiator Group’
4. Add Initiator to Initiator Group
- Create an ‘Add Initiator to Initiator Group’ workflow task and map the ‘Initiator Group Name’ entry to the OUTPUT_IGROUP_IDENTITY output variable from the ‘Create NetApp Initiator Group’ workflow task and map the ‘Initiator Name’ entry to the SP_VHBA1 output variable from the ‘Create UCS Service Profile’ workflow task created earlier in this flow.
- Repeat this task for in order to add initiator name entry for SP_VHBA2. Once done, re-map the successful output from the two Create Initiator Group workflow tasks so that they flow into each other as follows:
- Move onto the next step in order to map the created LUN to the initiator group.
And the rest of steps are fairly similar to above. Create a Workflow and map the User Input Mappings".
5. Map LUN to Initiator Group
6. Modify UCS Boot Policy LUN ID
7. Select UCS Server
8. Associate UCS Service Profile
9. Power On UCS Server
10. Modify UCS Service Profile Boot Policy
11. Add VLAN to Service Policy
12. Disassociate UCS Service Profile
13. Wait for Specified Duration
14. Associate UCS Service Profile
15. Power On UCS Server
16. Register Host with VCenter
regards
Andrew

Ask the Expert: C-Series Integration with Cisco Unified Computing System Manager

Welcome to the Cisco Support Community Ask the Expert conversation. This conversation is an opportunity to learn and ask questions about Cisco C-Series Integration with Cisco Unified Computing System® Manager (Cisco UCS® Manager) with Cisco experts Vishal Mehta and Manuel Velasco.
Cisco UCS C-Series Rack-Mount Servers are managed by the built-in standalone software, Cisco Integrated Management Controller (Cisco IMC). When a C-Series rack-mount server is integrated with Cisco UCS Manager, the IMC no longer manages the server. Instead you will manage the server using the Cisco UCS Manager GUI or Cisco UCS Manager command-line interface (CLI).
Cisco UCS Manager 2.2 provides three connectivity modes for Cisco UCS C-Series Rack-Mount Server management. The following are the connectivity modes:
Dual-wire management (shared LAN On Motherboard [LOM]): Shared LOM ports on the rack server are used exclusively for carrying management traffic.A separate cable connected to one of the ports on the Payment Card Industry Express (PCIe) card carries the data traffic.
SingleConnect (Sideband): Using Network Controller Sideband Interface (NC-SI), the Cisco UCS Virtual Interface Card 1225 (VIC1225) connects one cable that can carry both data and management traffic.
Direct Connect Mode: Cisco UCS Manager Version 2.2 introduces an additional rack server management mode using direct connection to the Fabric Interconnect.
Vishal Mehta is a customer support engineer for Cisco’s Data Center Server Virtualization Technical Assistance Center (TAC) team based in San Jose, California. He has been working in the TAC for the past 3 years with a primary focus on data center technologies such as Cisco Nexus® 5000, Cisco UCS, Cisco Nexus 1000V, and virtualization. He presented at Cisco Live in Orlando 2013 and will present at Cisco Live Milan 2014 (BRKCOM-3003, BRKDCT-3444, and LABDCT-2333). He holds a master’s degree from Rutgers University in electrical and computer engineering and has CCIE® certification (number 37139) in routing and switching and service provider.
Manuel Velasco is a customer support engineer for Cisco’s Data Center Server Virtualization TAC team based in San Jose, California. He has been working in the TAC for the past 3 years with a primary focus on data center technologies such as Cisco UCS, Cisco Nexus 1000V, and virtualization. Manuel holds a master’s degree in electrical engineering from California Polytechnic State University (Cal Poly) and CCNA® and VMware VCP certifications. Remember to use the rating system to let Vishal and Manuel know if you have received an adequate response.
Because of the volume expected during this event, our experts might not be able to answer every question. Remember that you can continue the conversation in the Data Center, under subcommunity, Unified Computing, shortly after the event. This event lasts through May 23, 2014. Visit this forum often to view responses to your questions and the questions of other Cisco Support Community members.

Hello Sebastian,
The different modes of connecting C-Series with UCSM come into play depending on the type of infrastructure you already have along with C-Series and NIC model.
Cisco UCS C-Series Rack-Mount Servers are managed by the built-in standalone software, Cisco Integrated Management Controller (CIMC) .
Powerful features provided by Cisco UCS Manager can be leveraged to manage C-Series server by integrating C-Series Rack-Mount Server with UCSM.
This not only gives you rich-feature set but also one management plane to operate UCS-B Series Chassis and UCS-C Series Rack Server.
You will manage the server using the Cisco UCS Manager GUI or Cisco UCS Manager CLI.
Cisco UCS Manager 2.2 provides three connectivity modes for Cisco UCS C-Series Rack-Mount Server management.
The following are the connectivity modes:
• Dual-wire Management (Shared LOM):
Shared LAN on Motherboard (LOM) ports on the rack server are used exclusively for carrying management traffic. A separate cable connected to one of the ports on the PCIe card carries the data traffic. Using two separate cables for managing data traffic and management traffic is also referred to as dual-wire management.
http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c-series_integration/ucsm2-2/b_C-Series-Integration_UCSM2-2/b_C-Series-Integration_UCSM2-2_chapter_0100.html
This mode is recommended when you have C-Server which does not have or cannot support VIC 1225 card (such C-200 server)
• SingleConnect (Sideband):
Using Network Controller Sideband Interface (NC-SI), Cisco UCS VIC1225 Virtual Interface Card (VIC) connects one cable that can carry both data traffic and management traffic.
This feature is referred to as SingleConnect.
http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c-series_integration/ucsm2-2/b_C-Series-Integration_UCSM2-2/b_C-Series-Integration_UCSM2-2_chapter_011.html
This most recommended Integration model when using FEX and VIC 1225 card
• Direct Connect Mode:
Cisco UCS Manager release version 2.2 introduces an additional rack server management mode using direct connection to the Fabric Interconnect.
This mode will eliminate the need for FEX module as Servers are directly plugged into the base ports of Fabric Interconnect
http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c-series_integration/ucsm2-2/b_C-Series-Integration_UCSM2-2/b_C-Series-Integration_UCSM2-2_chapter_0110.html
Please let us know if you need more information. Thank you!
Thanks,
Vishal

How to start study Unified Computing system & datacenter ?

Dear
Dear I am seniro system enginner and have back groud about Virtualzation and server hardware component
I need to strat stuady the Unified Computing system from scratch I need to understand the termonolgy and the concept
Please can anyone share Document to start or Guide me ?

Hi Ahmed
A new book just came out
Implementing Cisco UCS Solutions
http://www.packtpub.com/implementing-cisco-ucs-solutions/book?utm_source=mention.com&utm_medium=Links&utm_campaign=sales%20db
The classical one (no more up to date) is
Cisco Unified Computing System (UCS) (Data Center): A Complete Reference Guide to the Cisco Data Center Virtualization Server Architecture (Networking Technology)
1st (first) Edition by Gai, Silvano, Salli, Tommi, Andersson, Roger published by Cisco
Cisco Live has also many UCS introduction session, e.g.
https://www.ciscolive.com/online/connect/sessionDetail.ww?SESSION_ID=6287
BRKCOM-8636 - Introduction to Cisco Unified Computing System (Cisco UCS) Central - 90 Mins
This includes VoD and pdf

CISCO-UNIFIED-COMPUTING-TC-MIB won't compile

Hello,
I'm trying to monitor my UCS C260 using SNMP traps sent to HP SIM. In order do import the Cisco MIBs into SIM, you compile a .cfg file. One of the MIBs, CISCO-UNIFIED-COMPUTING-TC-MIB, will not compile. When running the mcompile command, I get the following error message:
C:\Program Files\HP\Systems Insight Manager\mibs>mcompile CISCO-UNIFIED-COMPUTING-tc-MIB.mib
HP Systems Insight Manager Mib Compiler, Version 5.0.2.1
Copyright (c) 2003-2006 Hewlett Packard Corporation
Compiling CISCO-UNIFIED-COMPUTING-tc-MIB.mib
Line: 128: Error defining object: expected a label, found reserved symbol {
Mib compilation failed.
All of the other MIBs compile just fine and I don't see anything wrong with the MIB I downloaded from Cisco.
Any idea what might be going on here?
Attached is the MIB as well.

Chaps, i had the same issue, spoke with the chaps from Castle Rock and they confirmed this was due to bad coding within the MIB file.
I have succesfully compiled the version kindly amended by castlerock, they were quick to resolve this, their explanation as to the problem as below:
The problems with the MIB were that they are trying to enumerate the values with gauge and counter types. Only INTEGER/Integer32 types may have enumerated values (RFC2578, 7.1.1). There isn't a 64 bit integer type so they can't enumerate the Counter64 bit values. There were also problems trying to enumerate a textual-convention type (snmpAdminString) which is wrong in two ways - you can't enumerate a string value, and you can't nest a textual convention macro as a syntax in another (RFC1903, 3.5).
Please find the version i used attached.
Please feed back to the forum if this resolves the issue for your type of platform.....
Cheers
Barry

Welcome to the Cisco Networking Professionals Unified Computing topic

Welcome to the Cisco Networking Professionals Unified Computing topic. This topic will provide you the opportunity to discuss issues such as building and running server virtualization, mobility management, stateless computing, application provisioning, implementation of FCoE and other solutions based on the Cisco Unified Computing System and Cisco Unified Fabric. We encourage everyone to share their knowledge and start conversations about challenges you might be facing.
Remember, just like in the workplace, be courteous to your fellow forum participants. Please refrain from using disparaging or obscene language or posting advertisements.
We encourage you to tell your fellow colleagues about the site.
Dan Bruhn
NetPro Community Manager

This is easily done with dial peer statements . The dial peer in your originating router must route the calls to the terminating router first. That would look like :
dial-peer voice xxxxx voip ( the xxxxx is just a tag)
destination-pattern 45... (that would route any 5-digit calls beginning with 45)
session-target ipv4:xxx.xxx.xxx.xxx (ip address of the terminating router)
If digitones are to be dialed after the connection is established, use the statement:
dtmf-relay-h.245-alphanumeric
You could also use a statement to specify the codec to be used:
codec g711ulaw
You would need multiple voip dial peers if the calls were going to different routers based on the dialed digits. If all calls are sent to the same terminating router, use all wild cards in the dest-pattern statement.
At the terminating router configure pots dial peers:
dial-peer voice xxxxx pots
dest-pattern 45...
port x/x (whichever port the call is to be terminated on)
prefix 45 (this re-inserts matched digits which are stripped off by the pots dp)
Repeat for other ports which will receive calls.
Paul

What is Cisco netManager-Unified Communications 1.0?

I want to know if this software let me add, change, manage extension in the CUCM6 platform or is just to monitor and diagnostic.
Thanks.

Hi Rafael,
Hope you are doing well :) You are most correct! Here are the various management for Unified Communications;
Cisco netManager - Unified Communications 1.0 provides simple, ready-to-use monitoring and diagnostics for small and medium sized deployments (up to 1000 users) of the Cisco Unified Communications System.
Key Features:
Monitors and evaluates the status of all the key components of a Cisco Unified Communications System, including the underlying transport infrastructure
Presents the current status of the system through service-level views of the network and provides contextual tools to view current alert status and historical information
Increases network manager productivity and speeds trouble-shooting by providing contextual diagnostic tools and easy one-click access to embedded device management systems
Provides current information about connectivity- and registration-related outages affecting all IP phones in the system and provides additional contextual information for location and identification of the phones
http://www.cisco.com/en/US/products/ps7243/index.html
Cisco Unified Operations Manager 2.0
provides a real-time, service-level view of the entire Cisco Unified Communications system and presents the current operational status of each element. It continuously monitors the different elements such as Cisco Unified CallManager, Cisco Unified CallManager Express, Cisco UnityÂ® systems, Cisco Unity Express, Cisco Unity Connection, Cisco Unified Contact Center, Cisco Unified Contact Center Express, Cisco Unified Presence Server, Cisco Emergency Responder, and Cisco Unified MeetingPlaceÂ® Express, as well as Cisco gateways, routers, switches, and IP phones.
http://www.cisco.com/en/US/prod/collateral/netmgtsw/ps6491/ps6705/ps6535/ps7121/prod_bulletin0900aecd805800c0.html
You would probably be looking for something like this;
Cisco Unified Provisioning Manager 1.2
http://www.cisco.com/en/US/prod/collateral/netmgtsw/ps6491/ps6705/ps7125/ps8771/prod_qas0900aecd80709f1e.html
Hope this helps!
Rob

Verifying data coming from Cisco Unified CCX Historical Reports

Good afternoon
I (along with a number of other colleagues) are heavily involved in a project to take data from a wide variety of different sources and merge it all into one system so that we can report on it in a joined-up manner.
The project comprises a number of different types of data source (such as Telephony or CRM). Within each data source type, we have various suppliers of those products. In the case of telephony data (which I'm looking into at the moment), the eventual aim is to make it possible to take data from any of the telephony platforms in use across our business (currently AVAYA, Alcatel and Cisco) and report on it in a uniform way, thus negating the need for an end-user to know what the Cisco definition of AHT is (for example).
The switch I'm currently looking at is a managed switch, meaning that we don't have any sort of direct access to the back-end database(s). We could probably get it, but I suspect that the company that manages it for us would probably charge a small fortune for that. In view of this, I'm working with a number of the standard reports in the Cisco Unified CCX system. My plan (at the moment anyway) is to identify the reports that we can use that will best provide details of all calls into and out of our contact centres. I'd be looking to get the exact details of each individual call, which could then be rolled up into manageable intervals (such as 15-minute or 30-minute).
Before I go much further, I'd like to be clear on something: I'm a database developer rather than a telecoms engineer so if I ask something that appears to be obvious then I apologise in advance. I've got quite a bit of experience of working with the CTI system that sits on top of our AVAYA platform, but it's proving to be a bit of a wrench effectively "un-learning" that system so that I can make room in my head for the Cisco solution.
So, what I've learned (or have guessed) so far is this:
When I run the Application Performance Analysis report, the Application Names that are returned are effectively the Call Routes that are set up in the system. Each Call Route can be fed by one or more Called Number (which I understand to essentially be a DDI);
The Application Summary Analysis report shows the same Application Name information as is shown in the Application Performance Report. However this report also shows the Called Number, thus providing slightly more information about the individual DDI being answered;
My next plan is to try and run an Agent-level report so that I can see exactly which calls each agent handled. This is where I've run into problems: I ran the CSQ - Agent Summary report for the whole of 17th October. I then ran the Agent Detail report for the same period, and ran it out to CSV so that I could "play" with the data. The CSQ - Agent Summary Report shows that a particular agent on a particular CSQ Name (ID) handled a total of 29 calls. However, if I filter the Agent Detail report for that agent and CSQ, I get a total of 30 calls and for the life of me am unable to identify where the missing call is coming from. Initially I'd thought it might be bacause the CSQ in question has two separate DDIs but as far as I can see, this is making no difference.
I NEED to be 100% sure that when I'm importing the data from the Cisco reports into our system, I am then able to mimic the types of reports that are coming from Cisco, with the same figures. Therefore, if anyone can help me, I'll be extremely grateful.
TIA
Ian Henderson

The "Cisco Unified CCX Historical Reports Scheduler" sits in my startup folder but seems like it doesn't "run" at startup. So I ran a "test":
- Manually right-clicked the "Cisco Unified CCX Historical Reports Scheduler" icon in the startup folder and chose "Run as Administrator"
I didn't log off or reboot PC and the reports are running again. I checked the "properties" of the icon and I did make sure it was already set to "Run this program as an Administrator" under the "Compatibility" tab.
Not sure why it's not working...
Thank you for any help you can provide....

Minimum computer system requirements for LabVIEW 7.1

What are the minimum computer system requirements for LabVIEW 7.1? I have a PC with the following specifications: 1.7 GHz Pentium-4, 512 MB RAM, and a 60 GB hard drive running Windows ME. I tried installing LabVIEW on the system but kept getting the "This computer does not meet the minimum requirements for this product" message. What's the problem here?
Thank you.

Hi Enhan,
You're problem may be related to the OS "Win-ME".
Your system appears fine, if there is room available on the HD.
Ray

Problems with iOS 7 Mail and Cisco Unified Messaging attachments?

Does anyone out there use Cisco Unified Messaging in their workplace? I am seeing an issue with iOS 7 (7.0.0-7.0.2) where the following scenario occurs:
You check an email in the Mail app that is from the Cisco Unified Messaging system when you get a voicemail. The voicemail is left by Person A who attaches a subsequent voicemail from Person B and they leave an intro saying "Attached is a voicemail blah blah blah" The email from Cisco comes across as having a .wav attachment and then an email attachment with a .wav file inside (supposed to be the original voicemail from Person B). If you play both .wav attachments, it just plays the same audio and not separate voicemails (one being the intro from Person A and one being the original Person B voicemail). It seems to hold on to whichever .wav attachment you played first (e.g. if you play the Person B voicemail .wav file and then go to the .wav file that should be Person A's intro, it just plays Person B's voicemail).
We did not experience this with iOS 6 and have confirmed that things work just fine on phones that have not been upgraded to iOS 7. Email account on iOS devices is a Microsoft Exchange account.
I am sorry if this is already a known issue, but I've had trouble searching for results. Any help would be tremendous in hunting down this strange phenomenon.
Thank you,
-Ted

Does anybody have even any thoughts on this and whether it might be a known issue of any kind? Anyone seeing this with other .wav attachments outside of Cisco UM ?

Cisco Unified CCX 8.5.1 problem in CSD when the CCX bascull

Hi,
I have a problem with the Cisco Supervisor Desktop. There is a cluster of 2 Cisco Unified CCX, system version: 8.5.1.10000-37. At this moment the IPCC2 is the Main and if the system bascull to the IPCC1 we have a problem with the Cisco Supervisor Desktop, the CSD does not monitors the agents.
Which could be the problem?
Thanks,
Regards,
David Lozano

Correct 64kbps.
Audacity or any sound application can do this.
Chris

UCCX cannot open the "Cisco Unified OS Administration" system

Hi,
When I select "Cisco Unified OS Administration" and click "Go", the system shows below error messages.
Navigation:
Cisco Unified CCX Administration (Can open this webpage)
Cisco Unified CCX Serviceability    (Can open this webpage)
Cisco Desktop Administrator         (Can open this webpage)
Cisco Unified Serviceability           (Can open this webpage)
Cisco Unified OS Administration   (Cannot open, it shows error page)
Disaster Recovery System           (Can open this webpage)
What is the problem?
Please help, thanks.
HTTP Status 500 -
type: Exception report
message:
description: The server encountered an internal error () that prevented it from fulfilling this request.
exception:
org.apache.jasper.JasperException: java.lang.NullPointerException
     org.apache.jasper.servlet.JspServletWrapper.service(JspServletWrapper.java:418)
     org.apache.jasper.servlet.JspServlet.serviceJspFile(JspServlet.java:342)
     org.apache.jasper.servlet.JspServlet.service(JspServlet.java:267)
     javax.servlet.http.HttpServlet.service(HttpServlet.java:717)
     sun.reflect.GeneratedMethodAccessor228.invoke(Unknown Source)
     sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
     java.lang.reflect.Method.invoke(Method.java:597)
     org.apache.catalina.security.SecurityUtil$1.run(SecurityUtil.java:269)
     java.security.AccessController.doPrivileged(Native Method)
     javax.security.auth.Subject.doAsPrivileged(Subject.java:517)
     org.apache.catalina.security.SecurityUtil.execute(SecurityUtil.java:301)
     org.apache.catalina.security.SecurityUtil.doAsPrivilege(SecurityUtil.java:162)
root cause:
java.lang.NullPointerException
     org.apache.struts.taglib.TagUtils.computeURLWithCharEncoding(TagUtils.java:428)
     org.apache.struts.taglib.TagUtils.computeURLWithCharEncoding(TagUtils.java:311)
     org.apache.struts.taglib.logic.RedirectTag.generateRedirectURL(RedirectTag.java:294)
     org.apache.struts.taglib.logic.RedirectTag.doEndTag(RedirectTag.java:268)
     org.apache.jsp.index_jsp._jspx_meth_logic_005fredirect_005f0(index_jsp.java:89)
     org.apache.jsp.index_jsp._jspService(index_jsp.java:64)
     org.apache.jasper.runtime.HttpJspBase.service(HttpJspBase.java:70)
     javax.servlet.http.HttpServlet.service(HttpServlet.java:717)
     org.apache.jasper.servlet.JspServletWrapper.service(JspServletWrapper.java:374)
     org.apache.jasper.servlet.JspServlet.serviceJspFile(JspServlet.java:342)
     org.apache.jasper.servlet.JspServlet.service(JspServlet.java:267)
     javax.servlet.http.HttpServlet.service(HttpServlet.java:717)
     sun.reflect.GeneratedMethodAccessor228.invoke(Unknown Source)
     sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
     java.lang.reflect.Method.invoke(Method.java:597)
     org.apache.catalina.security.SecurityUtil$1.run(SecurityUtil.java:269)
     java.security.AccessController.doPrivileged(Native Method)
     javax.security.auth.Subject.doAsPrivileged(Subject.java:517)
     org.apache.catalina.security.SecurityUtil.execute(SecurityUtil.java:301)
     org.apache.catalina.security.SecurityUtil.doAsPrivilege(SecurityUtil.java:162)
note: The full stack trace of the root cause is available in the logs.

Hi,
After reinstalling the UCCX system, everything is ok.
Thanks for your help.

Hi, I just purchased Adobe Illustrator and I cant find the serial number. When I try to download using Cloud it says it does not support my computer system. Just yesterday I finished my trial. What shall i do?

I just purchased Adobe Illustrator and I cant find the serial number. When I try to download using Cloud it says it does not support my computer system. Just yesterday I finished my trial. What shall i do?

To locate the serial number:
http://helpx.adobe.com/x-productkb/global/find-serial-number.html
http://helpx.adobe.com/x-productkb/policy-pricing/serial-number-retrieval-process-faq.html

When I try to update my iMovie to be Maverick compatible, this is what I get " Your computer's video card does not meet the minimum system requirements." Any suggestions? Thanks

When I try to update my iMovie to be Maverick compatible, this is what I get " Your computer’s video card does not meet the minimum system requirements." Any suggestions? Thanks

I have a Mac Pro earley 2008 with 16gb ram and the original ATI Radeon 2600 XT 256mb ram card.
After searching everywhere and finding no helpful info I just went to amazon and serched video cards for Mac Pro. The Asus HD 6450 silent and others came up. They all show PC compatibatily but since Mac is now PC structure I think allmost any card will work that is PCI-e.
I purchased the Asus HD 6450 for $39.00 with $10 rebate and it worked great, ( plug and play ).
My startup is way faster than before and graphics are way better.
The DVI works great with my Viewsonic and if you need to connect more than one monitor the DVI and VGA are secondary. If your main monitor is HDMI than you will have no problems using more than 2 screens in sharing mode.
http://www.amazon.com/s/ref=nb_sb_noss_1?url=search-alias%3Daps&field-keywords=A sus+hd+6450+silent&rh=i%3Aaps%2Ck%3AAsus+hd+6450+silent

You cannot sign in to the Cisco Unified MeetingPlace Web Server interface using preconfigured system profiles

Hi
I recently upgrade tp 7.0.3 from 7.0.2.
While upgrade i found that i am not able to login to the web server with the admin id "admin" default created in the application server.
The same id i can login to application server , but not in wewb server.
I am getting the mentioned error "You cannot sign in to the Cisco Unified MeetingPlace Web Server interface using preconfigured system profiles".
However if i create a new user in application server and tried logging with the same in the web server it is working fine..
is it a known behaviour wirh the upgrade or i m facing some issue.
Hope i can find a solution here.
Regards
RC

RC,
This behavior is stemming from a change in MP 7.0 MR2 to disable the MPWeb login for system profiles. This was an internal change made by the developers to restrict the log on to the MPWeb page by the default accounts created in MeetingPlace upon installation. The change now displays this error when the admin account is attempted to be used for MPWeb login, as you experienced-
Error:[22953] You cannot sign in to the Cisco Unified MeetingPlace Web Server interface using preconfigured system profiles.
You should be able to log into MPWeb using any other user profile that you have either created manually or pulled in from LDAP/Active Directory. You just cannot use the admin account. This is reserved for login to the MP Application Server Administration page only. I am going to work to get this information added to the MP 7.0 documentation with a note for changed behavior in MR2 and above. Here is the note from MP 8.0 documentation-
Note: You cannot use this preconfigured admin profile to access the Cisco Unified MeetingPlace Web Server interface. Instead enter the User ID and password information from one of the other user profiles that have system administrator privileges to sign in to the Web Server.
Please let me know if you have any further questions.
Thank You,
Gerry

What is Cisco Unified Computing System?

Similar Messages

Maybe you are looking for