What is error code post/16/2112

Hi, I have just run the Apple hardware check disc as I am having some problems with my G4 DA.
It reported a bad RAM stick (Kingston VRAM 512mb) so I removed it and the problem seems to have gone away, I ran Hardware disc again a couple of times to check everything and it comes back with the error code post/16/2112.... what does this mean?
Also, any thoughts why the RAM may have failed in the first place?
Thanks....

Thanks Thomas, I only have the keyboard and mouse and screen attatched at the moment, it has a USB2 expansion card and a 933mhz processor, other than that it is pretty much standard old G4... Could it be the Graphics card... I have been having trouble with my apple studio display, the card is a Rage Pro 128 with the ADC connector... any thoughts?
Thanks again...

Similar Messages

What is error code "post/16/2048 DIMM0/J22"?

What is error code "post/16/2048 DIMM0/J22"?
I'm thinking that may be why my startup sound isn't working
Thanks,
Mittens131
Using An iMac G4 (Flat Screen)

If you open up the machine and look, I suspect you will see that the slot is NOT empty. It is failing the power on self test, so the machine is not using it.
You can try opening the cover and then removing and reseating the memory. This might work, but probably not.
Other world computing is an excellent source for RAM and other mac upgrades.
http://macsales.com
I recommend looking over there, and adding some more memory is always a good idea IMO.
Good Luck,
Marty

What is error code post/0/2048?

2005 G5 20" iMac. Bought from apple with two 1 gb ram cards. (One Samsung, one ZK: I wonder why apple doesn't send matched pairs of ram...?) System Profiler always read these two ram cards as two single 1gb cards: one in each of my two slots. Now system profiler reads 512mb in each of the two slots. I swapped the two 1gb cards and put them in the slot the other came out of and the computer would not start. Just went bong, bong, bong bong. Any suggestions will be greatly appreciated ,

Did you return them to their original slots, and try a reset of the PRAM?
And/or also see if a reset of power management controller does anything.
It is possible that some aspect of the logic board has failed, so as to
no longer correctly recognize the RAM. How long has it been since
the PRAM or clock battery has been replaced? Some start issues
occur when the battery goes dead.
There could be a problem elsewhere in the computer, but without a way
to test the RAM separate from the G5 iMac, that is a continuing question.
Did you test the computer with an Apple Hardware Test?
May not work without functional RAM, if they're at fault.
If a reseller upgraded the RAM after original build, to a higher capacity,
they may have put two equal spec RAM chips inside, not same maker.
So if they've been working several years w/o issue until now, they may
not be the cause of the symptom. But they could be.
The original RAM chips may have a warranty (samsung would) so that
aspect of inconvenience could get you replacement part(s) if they're bad.
Usually three-startup beeps means bad RAM... You indicate Four-beeps.
{Three beeps would be an easier fix: try other memory chips}
•Power On Self-Test Beep Definition:
http://support.apple.com/kb/ht1547
Where did you find the error code, in the Console log files or a crash report?
Hardware Test report?
Someone here may be able to read or understand a greater section of a
error code post/0/2048 report, if this issue were brought to their attention.
•iMac G5 error code /0/2048 - google search result:
https://www.google.com/#q=iMac+G5+error+code+%2F0%2F2048
If the Mac were not so old, a visit to an Apple Store genius may help. Yet
now, to talk to a Specialist at an Apple Store or an independent authorized
Apple service expert may be of help. Whether or not it's worth shop time.
If a genius appointment and diagnostic could help discover cause of error,
to see if an Apple Store with Genius bar near you will talk to you about it
may be at least some momentum. Not sure if a power supply or other failed
component (capacitors?) may affect how this architecture reacts.
Sorry to not be of much help

Does anyone know what this error code means?My itunes will not open, no matter how many times i downlaod and restore it??? "The procedure entry point xmlITexTextReaderName could not be located in the dynamic link library libxml2.dlll."

Does anyone know what this error code means?My itunes will not even open, no matter how many times i downlaod and restore it??? "The procedure entry point xmlITexTextReaderName could not be located in the dynamic link library libxml2.dlll." Please let me know if your know anything! It is greatly apprecitated!

Taken at face value, you're having trouble with an Apple Application Support program file there. (Apple Application Support is where single copies of program files used by multiple different Apple programs are kept.)
Let's try something relatively simple first. Restart the PC. Head into your Add or Remove Programs control panel, select "Apple Application Support", click "Change" and then click "Repair".
If no joy after that, try the more rigorous uninstall/reinstall procedure from the following post. (Although the procedure is for Vista and 7 and you've got XP, just read "Computer" as "My Computer", read "Uninstall a program control panel" as "Add or Remove programs control panel" and assume the system is 32-bit, and you'll be doing the right things.)
Re: I recently updated to vista service pack 2 and I updated to itunes 10.2.1 and ever since I did that my itunes won't open any more. Itunes starts but before anything loads a

What does error code 5105 mean when trying to download facebook

What does error code 5105 mean when trying to download facebook

Kathleen I would recommend posting your inquiry to the Adobe Digital Editions forum.

Error Code Post/0/2048 DIMM3/J14

I'm trying to fingure out what this error code means when I ran the hardware test the message came us error code "Post/0/2048 DIMM3/J14
It indiacted I may have to reformat the media? I have also lost the CD needed to reformat. Anyone konow what the error code is and where I can get another CD?
Thanks
Tom

It would appear that you have a problem with one of your ram chips. Try changing the chips and run the test again. See HERE. This is the Aluminum Powerbook forum are and you might get more expert help on your G5 Dual over in that forum area. Never, never lose your OS installer CD/DVD. That should be in the vault. You may try to contact AppleCare to see if they can help you get another one.

Error code post/16/64?

I've been having recurring problems with my G4.
Symptoms:
2nd internal hard drive warning such as prompting an error message of 'you must initialize, ignore, eject' then I re-boot, other times a prohibit sign, spinning rainbows, kernel panics. It's a mess.
This only happens on start up after shutting down for the night. But I think I've made things worse
I ran suggested back-ups, PRAM resets, ran cocktail, tried disk utility from start up, ran disk warrior from start up, it found some file errors, cleaned them up. Cloned my system using Superduper, backed the hd up on a NewerTech.
Next day, start up issues again.
I ran memtest, and that found nothing. Start up from install disc, ran disk utility, everything's passing, SMART status is verified.
But it is still not operating correctly. I still have start up issues.
This has been going on for at least a week.
I ran AHT twice. The first time all tests passed. I didn't believe it.
So I ran it again and I received the following:
error detection at the logic board:
error code: scc_/1/5 (I think this is a non-apple board warning)
error code: post/16/64.
What?
My internal HD (original) is running at 85% (60g)
My second internal is 120g partitioned with mostly back-ups (not the only back up) and documents.
Thank you to all the folks who've generously posted in the past and thank you in advance for the one that catches this.
-M
G4, gigadesign 1.2, 1.25 ram, radeon 9800 pro Mac OS X (10.3.9) originally QS 933

The POST/16/64 points to an error on your processor board, bad cache memory. I had this same error, still have the processor on a shelf actually, and it took me months to find the code translation.
Apple says for a POST/16/xx error
1. replace processor board
2. replace main logic board
I don't know if there is a heat issue that causes this, but, several cases that I have heard of had systems that ran very hot.
A fellow in Singapore mentioned that he had the same error and believes that the heat causes the external cache chips on the 7455 processor board to loosen(I think your Gigadesigns is a 7447 based chip). He stated that he heated his chips and resolved the error:
"The cache are DDR type samsung BGA chips. This is most difficult as both sits directly opp each other. The only way I think is to heat the chip on 1 side below 220degC(removal at 350degC and soldering in at 300degC). Best if you can get a heater blower and blow at the small gap bet chip and processor board, very tiny clearance, less than 1mm. You can give it a try for the time being, on the chip itself though not the most ideal."
If there are other numbers at the end, ie POST/16/xx yyyy then it is likely a RAM problem or RAM slot problem
1. reseat DIMMs
2. replace DIMMS
3. replace main logic board
Hope this helps, I ended up replacing my processor and as I stated before still have the originalon a shelf. I may try the heat trick one day though.
QS 2002 Dual 1GHz, FW800 Dual 1.25GHz, iBook 1.33GHz, G5 2003 Dual 2GHz Mac OS X (10.4.8)

TS3694 what is error code 40?

What does error code 40 mean ? What do I have to do to fix my phone? it will not restore and I keep getting error code 40

Everything we know about it is in the knowledge base article you were reading when you posted the question.
http://support.apple.com/kb/TS3694#error40
Basically, it says that your antivirus or firewall is preventing iTunes from updating your phone. Try disabling them. It may also be necessary to delete the possibly corrupt .ipsw file. That's described under Advanced Steps in TS3694.

TS3694 what is error code 1015? i can not restore my iphone for this code. thanks

im having a issue with my sons iphone. it wont restore! can anyone help in this matter? thank you

Your phone is jailbroken. That's what the error code means. It's likely you'll never get it working again.
Further discussion of jailbroken phones is against the Terms of Use of this forum that YOU agreed to by signing up to post here.
You'll have to go elsewhere for help, if there's even any help to be had.

What does (error code -600) mean?

What does (error code -600) mean?
I received this code in a pop up window while trying to open iTunes from my Apps folder.

procNotFound
= -600, /*no eligible process with specified descriptor*/
Could be many things, we should start with this...
"Try Disk Utility
1. Insert the Mac OS X Install disc, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu at top of the screen. (In Mac OS X 10.4 or later, you must select your language first.)
*Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
3. Click the First Aid tab.
4. Select your Mac OS X volume.
5. Click Repair Disk, (not Repair Permissions). Disk Utility checks and repairs the disk."
http://docs.info.apple.com/article.html?artnum=106214
Then try a Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
(Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive.)
If perchance you can't find your install Disc, at least try it from the Safe Boot part onward.
Any change?

What is error code 603 and how does one fix it?

What is error code 603, please, regarding add-on installation? (The error codes page says for "error 6xx" to contact the Exchange online forum for assistance..) It is a "failed online license check" for an add-on that is a free add-on listed on the Adobe Add-ons page as compatible with PS CS6, CC, and CC 2014, as well as all three versions of a bunch of other apps. It is a Flypaper app, which looks to have been reworked to be compatible with the new 2014 apps. Since Flypaper apps come from reliable source, I'm not sure what the error means, and I'm certainly not sure how to remedy this. (The original Russell Brown Paper Textures Pro works fine on PS CC but isn't compatible with 2014.)
I am running Win 7 64-bit.
Thanks.
Gail
p.s. numbers of other extensions still don't download to PS 2014, so maybe this is also waiting for an Adobe fix??

The add-on in question is called "Flypaper Select" (by Flypaper Textures).
This morning, when I sent the question, it was on last page of the free PS
add-on list and showed the add-on as compatible with all three latest PS
versions. Tonight, when I click on the add-on in "my add-ons" list, it now
shows compatibility only with PS6 and CC, and I can no longer even find it
in the big add-ons list. I will try to send screen shot of "my add-ons" to
the address you listed. It is also below.
Thanks for your help. I have been finding many add-ons change from day to
day, and many won't show up in Extensions window even though the desktop CC
app says they have been installed. I assume I am not the only person with
these problems.
Gail

HT201210 what is error code (1)? it is not listed but this is the error i get trying to restore my 3gs.

what is error code (1)? it is not listed but this is the error i get trying to restore

Take a look here for Apple's suggestions on that error:
http://support.apple.com/kb/TS3694#error1
Regards.

TS3694 what is error code 1015 trying to restore but keeps coming up with this code

what is error code 1015 trying to restore phone keeps saying in recovery but keeps coming up with this error code help please

Are you trying to downgrade your iPhone?
Errors related to downgrading iOS
The required resource cannot be found: This alert message occurs when your device has a newer version of iOS than what is available in iTunes. When troubleshooting a device that presents this alert message, go to Settings > General > About and check the version of iOS on the device. If it is newer than the latest released iOS version, the device may have a prerelease developer version of iOS installed. Installing an older version of iOS over a newer version is not supported.
Error 1015: This error is typically caused by attempts to downgrade the iPhone, iPad, or iPod touch's software. This can occur when you attempt to restore using an older .ipsw file. Downgrading to a previous version is not supported. To resolve this issue, attempt to restore with the latest iPhone, iPad, or iPod touch software available from Apple. This error can also occur when an unauthorized modification of the iOS has occurred and you are now trying to restore to an authorized, default state.
(from iTunes: Specific update-and-restore error messages and advanced troubleshooting)
If not, try to move or delete the IPSW file and let iTunes download it again.
Rename, move, or delete the iOS software file (.ipsw)
iTunes uses "ipsw" files to restore your device. If those files are unusable, then try deleting them, renaming them, or moving the file to a different directory. This will cause iTunes to download a new copy of the IPSW. When a restore issue is specific to a user, it is likely due to an unusable .ipsw file. If removing the .ipsw file does not resolve a user-specific restore issue, then the issue is caused by other user-specific security software settings or iTunes preferences. Creating a new user will also cause new .ipsw restore files to be downloaded in the new user. You can find the ".ipsw" files in these locations:
Mac OS X
iPhone
~/Library/iTunes/iPhone Software Updates
iPad
~/Library/iTunes/iPad Software Updates
iPod touch
~/Library/iTunes/iPod Software Updates
Note: The tilde "~" represents your Home directory.
Windows XP
iPhone
C:\Documents and Settings\[username]\Application Data\Apple Computer\iTunes\iPhone Software Updates
iPad
C:\Documents and Settings\[username]\Application Data\Apple Computer\iTunes\iPad Software Updates
iPod touch
C:\Documents and Settings\[username]\Application Data\Apple Computer\iTunes\iPod Software Updates
Note: To quickly access the Application Data folder, click Start, and then choose Run. Type %appdata% and click OK.
Windows 7 and Vista
iPhone
C:\Users\[username]\AppData\Roaming\Apple Computer\iTunes\iPhone Software Updates
iPad
C:\Users\[username]\AppData\Roaming\Apple Computer\iTunes\iPad Software Updates
iPod touch
C:\Users\[username]\AppData\Roaming\Apple Computer\iTunes\iPod Software Updates
Note: To quickly access the AppData folder, click Start, and then in the search bar type %appdata% and press the Return key.

What does error code 50 mean when installing the creative cloud app?

what does error code 50 mean when installing the creative cloud app?

Hello,
This thread may help
Error code 50
Let us know!
Regards,
Jo-Marie

What is error code 2324 when installing iTunes?

What is error code 2324? I got this when trying to re-install iTunes. I was in the middle of the latest iTunes update when I had to cancel it. Now I can't access my music so I tried to reinstall iTunes but I get this error code. I also get a error message saying I need Administrator privlages. Well I am the Admininstrator and logged in as it. I can't reinstall iTunes and when I go to remove programs I don't see it listed only Apple Application and Apple Updates, along with an Apple Mobile Device Support.
I even 'restored' my system to earlier today before I started downloading the iTunes update to no avail. Any ideas/suggestions?

Let's try the fixit from the following Microsoft document with that one:
Fix problems with programs that can't be installed or uninstalled

What is error code post/16/2112

Similar Messages

Maybe you are looking for