What is "external mode" on iPhone 4S?

I just got a jvc car stereo which can display motionX drive and jvc support says to put iPhone in external mode.

It can means the iPhone was hacked/jailbroken. Ask for a refund.

Similar Messages

  • What is the best external battery for iphone 4s

    what is the best external battery for iphone 4s

    I bought the Mophie juice pack™ powerstation from the Apple store for $80. It has more then enough power to quickly boost the charge on my iPhone4S to an acceptable level. It requires the standard 30pin/USB Apple cord to plug into it.
    But unless you need to charge your phone from 5-100%, this battery is overkill. It's a real hassle having the Apple cord connected to your phone whilst there's a battery in your pocket and you end up looking quite strange with your "corded" smartphone.
    I might recommend a battery case (Mophie has these), but they don't offer the protection that I need (I use a LifeProof case).  Instead I would buy a smaller Mophie juice pack™ reserve (keychain, direct plug) to get out of a bind and then charge up your iPhone in the car, wall, airplane, etc.
    My only concern with the above (direct plug batteries) is that the slightest bump and the battery becomes a lever that could break the 30 pin plug on your phone, just like that warily flimsy feeling when you put an iPhone in a dock.
    Hope that helps, at least in the Mophie department!

  • USB 6009 DAQ to use in Simulink at External mode with DAQ toolbox

    hi
    Currently I am using usb 6009 daq board for data acquisition in using simulink. I have created a model with taking analog input from data acquisition toolbox. Then when i want to run in external mode and try to connet to target, the following error is coming up:
    Could not execute target data map file 'untitled_rtwin_win32\untitled_targ_data_map' or it does not exist. Stop the target, delete the untitled executable, rebuild the code,and try again. Note that execution of external mode requires the build directory to be present...
    How can I solve this problem? For your info, I am using 32-bit matlab, version: 2012a
    For your info, a snapshot of the error is attached,
    Any help would be appreciated Thanks
    Attachments:
    Untitled.jpg ‏130 KB

    Hi Mahmudur,
    what does MathWorks say about this error message?
    Best regards,
    GerdW
    CLAD, using 2009SP1 + LV2011SP1 + LV2014SP1 on WinXP+Win7+cRIO
    Kudos are welcome

  • What Superdrive (external USB) is compatable with Mountain Lion 10.8.3?

    What Superdrive (external USB) is compatable with Mountain Lion 10.8.3? 
    My New install of 10.8.3, will now.... not reconize anything I put in my drive... it spits it back out!
    Superdrive does NOT reconize any activity. 
    It will show my information on/of my drive...but, that is about it...
    Is there a patch/fix for this issue with 10.8.3?
    If not...why is Apple (seemingly) ignoring this issue? There are so many with the same complaint.
    They want $19 to answer this question...why? I just bought the upgrade to 10.8.3 a couple of days ago.
    Anyone have any suggestion, beside switching BACK to Microsoft...?
    ~JOHN~
    My "About This Computer" info:
    Hardware Overview:
      Model Name:    Mac mini
      Model Identifier:    Macmini5,1
      Processor Name:    Intel Core i5
      Processor Speed:    2.3 GHz
      Number of Processors:    1
      Total Number of Cores:    2
      L2 Cache (per Core):    256 KB
      L3 Cache:    3 MB
      Memory:    4 GB
      Boot ROM Version:    MM51.0077.B10
      SMC Version (system):    1.76f0
      Serial Number (system):    C0*******JD0
      Hardware UUID:    ****
    HL-DT-ST DVDRW  GX30N:
      Firmware Revision:    RP09
      Interconnect:    USB
      Burn Support:    Yes (Apple Shipping Drive)
      Cache:    1536 KB
      Reads DVD:    Yes
      CD-Write:    -R, -RW
      DVD-Write:    -R, -R DL, -RW, +R, +R DL, +RW
      Write Strategies:    CD-TAO, CD-SAO, CD-Raw, DVD-DAO
      Media:    To show the available burn speeds, insert a disc and choose View > Refresh
    System Software Overview
    System Version:                    OS X 10.8.3 (12D78)
    Kernal Version:                      Darwin 12.3.0
    Boot Volume:                         Mac OS X
    Boot Mode:                            Normal
    Computer Name:                   John's Mac Mini
    User Name:                           John Lipscomb (johnlipscomb)
    Secure Virtual Memory:         Enabled
    Time since boot:                    6:04
    <Edited By Host>

    Sorry about the serial number...wasn't thinking.  Mentally noted.
    I would think it to not be too much, to ask for it to be able to read/write to the listed capablities list with the product (superdrive). The different media type...
    I insert blank -R DVD, -R CD, ...anything I put in,it spits it out.  NOTE:  The ONLY thing I've been able to get it to read, is some old CD's that I had some mp3 files on...it would read that OK... but if I try a DVD read or write and write a CD...NOTHING!
    This worked fine before upgrading to 10.8.3   was at 10.7.5....
    Any help would be much appreciated.
    ~JOHN~

  • How to exit recovery mode on iphone 4?

    How do i EXIT recovery mode on iphone 4?
    I wanted to update my moms iphone 4 to ios 7.
    So i started the update and i didnt use the computer then i realized i didn't back up and it was installing it it was almost a half way so i wanted to exit that so i pressed both lockbutton and home button and then it showed me that i got to connect the iphone to itunes (recoverymode) and it says i have to restore.
    I cant restore my mom will kill me!
    She doesnt know what i have done.
    I tried using tinyumbrella and recboot and it didnt work... i tried pressing home and lock buttons and it didnt work.
    I dont know what to do please help me!!
    If there is a way to save photos to computer while recovery mode that would be great! The photos are important!
    Help!

    no way to exit recovery mode sorry.  you have to restore and setup as new unless you have a backup.
    Peace, Clyde

  • HT1320 what is disc mode error message mean?

    What is disc mode error message mean?

    A few years down the road, but I have a thought.  I nornally use an external burner since it is faster and frankly more reliable.  Today, I was doing a quick job so I started burning cds with IDENTICAL files for 7 clients.  First 5 urned without error.  Started #6 and 0x80020022 error code appeared.  The cds were formatted for music, as most are these days.  I switched to a cheaper unformatted cd and low and behold...no error.  Two more clean burns.  Might it be that the software reads the files ... and limits the copies to the number of legit copies allowed by iTunes.  I know that sound bizarre, but when all other reasonable explanations fail, I suggest the unreasonable one as an option. 
    Anyway, the text, pdf, and jpg files are all burned, but the opening file names were the same; only one picture changed with each cd and that was not the first file on the list.  Code writers sometimes go for the elegant (read shortest) code solution.  So forget speed.  How many copies are you making and are the file names (especially the first ones) identical. 

  • What shall i do my iphone showing activation failed during startup?

    what shall i do my iphone showing activation failed during startup?

    Hi funkeyankey,
    It sounds like your phone is not activating correctly when you are trying to set it up. I would recommend the troubleshooting from the following article named:
    Get help activating your iPhone
    http://support.apple.com/kb/ts3424
    Check the system status for iOS Device Activation. If the iOS Device Activation status isn't green, try activating your iPhone later.
    Restart the iPhone.
    Try to reach the activation server another way, then try to activate.
    Try connecting to a known-good Wi-Fi network if you can't activate using a cellular data connection.
    Try connecting to iTunes if you can't activate using Wi-Fi.
    Restore the iPhone.
    If you receive an alert message when you try to activate your iPhone, place the iPhone in recovery mode and perform a restore. If you still can't complete the setup assistant due to an activation error, contact Apple for assistance.
    If you're asked to enter a password to proceed with activating the iPhone, Activation Lock might be enabled as part of Find my iPhone.
    Thank you for using Apple Support Communities.
    All the very best,
    Sterling

  • What can I do if iPhone 5 is not powering after after I put it charge?

    What can I do if iPhone 5 is not powering after after I put it charge?

    Hmmmm are you saying tht it will not turn on even after being charged?
    Take a look at this article named iPhone: Hardware troubleshooting http://support.apple.com/kb/TS2802
    Battery does not charge from the USB power adapter
    Important: Only original iPhone can be charged from a FireWire-based power source. If iPhone is connected to a computer that's turned off or is in sleep or standby mode, the battery may drain.
    Verify that the outlet being used is working.
    Try another USB power adapter if available.
    If no other USB power adapter is available, try connecting to a high-power USB 2.0 port (not a keyboard). The computer must be turned on and not in sleep or standby mode.
    Try another USB cable if available.
    Also refer to iPhone and iPod touch: Charging the battery.

  • I can't decide what to buy ipad or iphone 3GS

    I can't decide what to buy ipad or iphone 3GS Can you request me some ideas or solutions...

    I have both an iPad and a highly capable smartphone (HTC Incredible), which while not an iPhone, fills the same needs in my life. If I had to choose one device, phone or iPad, it would have to be phone as text messaging is my primary mode of communciation, everyone has my phone number and text messaging on the iPad would not be as convenient and an iPad won't fit in my pocket.
    The iPad sits somewhere between my Macbook and my phone. It has pretty much replaced the Windows XP netbook I used to take out and about. With it's stellar battery life, huge screen and instant on, it's much pleasanter to use while sitting in a coffee shop or while eating lunch alone.
    However, without knowing your needs, it would be pretty hard to make a recommendation.
    Best of luck.

  • HT1430 what to do if my iphone saying disable conncet to itunes

    what to do if my iphone saying disable conect to itunes

    Connect to iTunes on the computer you usually Sync with and Restore...
    If necessary Place the Device into Recovery mode..
    http://support.apple.com/kb/HT1808

  • Can smbody please tell me what to do to my iPhone 4s, when playing music or ringer, the sound will just stop without stop it.. I am really getting tired of this...

    Can smbody please tell me what to do to my iPhone 4s, when playing music or ringer, the sound will just stop without stop it.. I am really getting tired of this...

    After updating to iOS6, I lost all sound for apps like YouTube, Netflix, games, and even notifications. The only time sound worked was during a phone call or when the head set was plugged in.
    I did a full back up and restore- sound restored but only for a day before the problem returned.
    Called Apple Support and was advised to do another restore, but this time restore it as NEW first, then do the restore from back up.
    Seemed to do the trick.
    Here are the instructions of what I was given- hopefully this will help you too:
    Here is a link about backing up your iPhone with iTunes.
    http://support.apple.com/kb/HT1766?viewlocale=en_US
    Once you back up your device you will want to restore it.
    You will need to have iTunes open on your computer screen.
    Please turn your iPhone off.
    Press and hold the Home Button.
    Continue to hold the Home Button as you plug you iPhone in to the usb cable.
    You will want to continue to hold the Home button until you get a screen with the message "device found in recovery mode".
    Please follow the prompts and restore device as NEW.
    once the restore is done you will have to set up the device and test the sound.
    If it works you will then need to restore the device from the back up to restore your user settings.
    You can find the instructions how to restore from back up also from the the link I provided.

  • I've broken my iPhone and have put my sim card in my old iPhone 3. If I plug my old iPhone 3 into my computer, will it update the iPhone 3 with everything that is on my phone that is now broken, or will it 'update' iTunes with what was on the old iPhone?

    I've broken my iPhone and have put my sim card in my old iPhone 3. If I plug my old iPhone 3 into my computer, will it update the iPhone 3 with everything that is on my phone that is now broken, or will it 'update' iTunes with what was on the old iPhone?

    Plug your phone into the wall charger for at least 30 minutes...make sure you have a sim card in the phone...then:
    Leave the USB cable connected to your computer, but NOT your phone, iTunes running, press & hold the home button while connecting the USB cable to your dock connector, continue holding the home button until you see “Connect to iTunes” on the screen. You may now release the home button. iTunes should now display that it has detected your phone in recovery mode, if not quit and reopen iTunes. If you still don’t see the recovery message repeat these steps again. iTunes will give you the option to restore from a backup or set up as new.
    Make sure you have no anti-virus software running or any firewalls...turn all of that stuff off.

  • Differecne between internal mode and external mode

    Hi all,
           In Integration Builder you have Two Modes 1)Internal Mode and 2) External Mode.Does any one what is the difference between these two terms.Can you please send me the link where can i find the details of this Mode.
    Thanks,
    kiran.

    Hi
    http://help.sap.com/saphelp_nw04/helpdata/en/2b/cd6a8bceed26469f3b0952a030c711/frameset.htm
    http://help.sap.com/saphelp_nw04s/helpdata/en/d7/2f2c1f4b40424f8c6ddca5c3adc486/frameset.htm
    Thanks

  • I want to set up the Time Machine and I would love to use the Time  Capsule but since I already have a wireless router I need suggestions on  what other external disks Apple could recommend to use with the Time Machine and  how to configure that disk

    I want to set up the Time Machine and I would love to use the Time
    Capsule but since I already have a wireless router I need suggestions on
    what other
    external disks Apple could recommend to use with the Time Machine and
    how to configure that disk.
    A complication that I need to resolve is the fact that I am using Vmware
    Fusion to be able to use Windows on my Mac. Now it seems that Time
    Machine is not backing up my files
    on that virtual Windows without additional configuration and my question
    is whether you can advise me here or whether this is only a matter for
    the Fusion virtual machine.

    If you want to use Time Capsule you can.. you simply bridge it and plug it into the existing router.. wireless can be either turned off or used to reinforce the existing wireless.. eg use 5ghz in the TC which is much faster than your 2.4ghz.
    You can also use a NAS.. many brands available but the top brands are synology, qnap and netgear readynas  series. These will all do Time Machine backups although how well always depends on Apple sticking to a standard. There are cheaper ones.. I bought a single disk zyxel which was rebadged and sold through my local supermarket. It actually works very well for TM at least on Snow Leopard. Major changes were made in Lion and again ML so do not instantly think it will work on later versions. I haven't tried it yet with those versions.
    Any external drive can be plugged into the mac. Use the one with the fastest connection or cheapest price according to your budget. USB2 drives are cheap and plentiful. But no where near as fast as USB3 or FW800. So just pick whichever suits the ports on your Mac. Interesting Apple finally moved to USB3 on their latest computers.
    TM should exclude the VM partition file.. it is useless backing it up from Mac OS side.. and will slow TM as it needs to backup that partition everyday for no purpose.. TM cannot see the files inside it to backup just the changes.
    You need to backup windows from windows. Use MSbackup to external drive.. if you have pro or ultimate versions you can backup to network drive. But MSbackup is a dog.. at least until the latest version it cannot restore the partition without first loading windows. There are about a zillion backup software versions for windows.. look up reviews and buy one which works for you. I use a free one Macrium Reflect which does full disk backups and is easy to restore.. to do incremental backups though you have to pay for it.

  • Whats the difference between an iPhone 5s and a iPhone 5c

    Whats the difference between the iphone 5s and the iphone 5c???

    Rider11 wrote:
    The 5c has plastic backs with different colors just for fun other then that nothing is different.
    You'd better look up the above linked comparison as well if you believe you are correct....

Maybe you are looking for

  • Select All in Mailboxes in iOS

    I am looking to find out if there's some shortcut, trick, or hint as to how to do a select all in one of the mailboxes in Mail for iOS.  I realize you can Delete All in the trash, which is helpful, but I'm looking for a way to, for example, not have

  • How can I edit text in a tagged PDF?

    I have created an accessible test form in Acrobat Pro X.  Now that it has all been tagged and reading order touched up, the client wants to change the text.  Is there any way to edit text at this point or do I have to create an entirely new tagged ac

  • How can I convert downloaded mpeg 4 music to high quality mp3

    I need to be able to convert MPEG 4 files from Itunes into MP3 but the default is set at 160KBPS can I set it higher in Itunes ????

  • How to set up reconciliation for a custom resource?

    Hello, I have a custom connector that I need to set up. To provision to this system, I will write the provisioning information into a file. The target system takes that info and somehow knows how to consume it. I am wondering how I can set up the rec

  • IPhone Slider won't work??

    My iphone slider just stopped working i've tried restarting it and turning it off multiple times..how do i fix this?? even restored it which did not work. Please help!