What is the algorithmn for smoothing filtering in Filter VI?

What is the algorithmn for smoothing filtering found in Filter VI of Labview 7?

The Smoothing selection the the Filter Express VI uses a moving average. To do this it implements an IIR filter. You can open the Filter Express VI up and look inside (to a point) to see exactly how it is working. You can't see the algorithm that they used for the IIR itself, however. To open it up, drop one, configure it, and then right click on the icon and select Open front panel from the menu list.
Hope that this helps,
Bob Young
Bob Young - Test Engineer - Lapsed Certified LabVIEW Developer
DISTek Integration, Inc. - NI Alliance Member
mailto:[email protected]

Similar Messages

What is the limit for EMAIL FILTERS?

At the beginning of my experience with VZ, I liked the idea of being able to filter my incoming emails, because it helped in putting information in place where I could find it. Through the years this feature has become less and less reliable, because it seems that some of the prior filters that I setup are no longer present? So I am now at the point of asking just how many filters I am allowed to have for this ISP? I have never received a notice of any kind that this type of change had been put into effect. If someone could answer this, it will sure help me in future usage and planning.
Thanks in advance . . .
{edited for privacy}

I have not heard or could find any documentation on the amount of filters you can have on your account. If the filters you have setup are not working, my suggestion would be to start by deleting and recreating them one by one.
Anthony_VZ
**If someones post has helped you, please acknowledge their assistance by clicking the red thumbs up button to give them Kudos. If you are the original poster and any response gave you your answer, please mark the post that had the answer as the solution**
Notice: Content posted by Verizon employees is meant to be informational and does not supersede or change the Verizon Forums User Guidelines or Terms or Service, or your Customer Agreement Terms and Conditions or plan

What is the limit for MAC filtering?

I use MAC filtering as a wireless security measure on my Time Capsule. I have a lot of wireless devices in my home which all require the MAC address to be entered into the Time Capsule.
It seems that after certain number of devices are entered (around 60), my airport starts dropping wireless connections on my network. For instance, right now all of my devices are working fine. When I enter a new device and save the changes, my Time Capsule drops several other devices from the network. They are still in the MAC filtering list, but suddenly disappear from the network and I can't get them back unless I remove the MAC filtering option (making it an open network) or remove other devices from the list.
Really wierd and I'm wondering if anyone else has this issue.
Thanks.

Apple won't look at anything unless you let them know what you want. You can do so here:
Apple - Time Capsule - Feedback

Adobe X PDF files converted to jpg, edited and converted back to PDF have ragged, unclear text. I didn't have this problem with Acrobat 9 standard. What is the remedy for this. If this is the best I can expect, I won't be able to use X standard.

Adobe X PDF files converted to jpg, edited and converted back to PDF have ragged, unclear text. I didn't have this problem with Acrobat 9 standard. What is the remedy for this. If this is the best I can expect, I won't be able to use X standard.

I can't imagine any worse workflow than converting to JPEG to edit text, then back to PDF. Text in a PDF is a vector thing, smooth at all resolutions. And JPEG is made for photos. EVERY conversion to JPEG and back loses quality but how much loss there is will vary.
If you must go to an image format, try PNG.

What's the difference between segment filtering and reduced message type

Hi gurus,
What's the difference between segment filtering and reduced message type? It seems they have the same functionality: Reduce the segment while idoc is generated.
Thanks in advance.

Hi,
BD53 is for IDoc Reduction.
this allows you to create a reduced message based upon a standard message type.If you want see mandatory fields. go to T-coe BD53 and give one standard messege type name and eg: matmas
there mandatory fields will be in Green color..
And BD56- This transaction is used to filter out segments of IDocs for combination of sender and receiver. This is usefull in scenarios where a standard IDoc with many segments is used but the receiving partner is only interested in some of the segments
the table related to this transation is TBD20
please go through below blog you have an idea abt that,
http://wiki.sdn.sap.com/wiki/display/ABAP/ReducedMessageTypes
http://saptotal.com/IDoc%20Segment%20Filtering.html
regards,
ganesh.

What is the use of these filters in atg

Hi Guys,
In my web.xml file i have code like this
<filter>
 <filter-name>PageFilter</filter-name>
 <filter-class>atg.filter.dspjsp.PageFilter</filter-class>
 </filter>
 <filter>
 <filter-name>ForwardFilter</filter-name>
 <filter-class>atg.servlet.ForwardFilter</filter-class>
 </filter>
 <filter>
 <filter-name>ErrorFilter</filter-name>
 <filter-class>atg.servlet.ErrorFilter</filter-class>
 </filter>
 <filter-mapping>
 <filter-name>ErrorFilter</filter-name>
 <url-pattern>/*</url-pattern>
 <dispatcher>ERROR</dispatcher>
 </filter-mapping>
 <filter-mapping>
 <filter-name>ForwardFilter</filter-name>
 <url-pattern>/*</url-pattern>
 <dispatcher>FORWARD</dispatcher>
 <dispatcher>ERROR</dispatcher>
 </filter-mapping>
 <filter-mapping>
 <filter-name>PageFilter</filter-name>
 <url-pattern>/*</url-pattern>
 <dispatcher>REQUEST</dispatcher>
 <dispatcher>ERROR</dispatcher>
 <dispatcher>FORWARD</dispatcher>
 </filter-mapping>
what is the use of these filters what will happend if i remove these filters in web.xml file
please give me clear picture on these 3 filters and how these filters are helpful in our application.

As the name filter suggest, All the request will go though these filters if certian condition is satisfied
In ATG web.xml contains following filter:
<filter>
 <filter-name>PageFilter</filter-name>
 <filter-class>atg.filter.dspjsp.PageFilter</filter-class>
</filter>
<filter-mapping>
 <filter-name>PageFilter</filter-name>
 <url-pattern>*.jsp</url-pattern>
</filter-mapping>
When there is .jsp in url pattern all the request will go through Page Filter.
Filter is java concept.For More details about Filter, Refer http://docs.oracle.com/cd/E19502-01/819-3669/6n5sg7b0b/index.html
In order to process Jsp request, ATG use Page filter. It converts normal HttpRequest/HttpResponse to DynamoHttpRequest/DynamoHttpResponse. Please refer http://docs.oracle.com/cd/E24152_01/Platform.10-1/ATGPlatformProgGuide/html/s0801requesthandlingwithservletpipeli01.html

What is the condition for using 'for all entries' and why?

what is the condition for using 'for all entries' and why? can any body tell the reason for this ? its a big favour of me .
regards,
ravi.

hi,
for all entries is used to join two or more tables.
It is same as join but performance wise for all entries is more effective.
You can only use FOR ALL ENTRIES IN ...WHERE ...in a SELECT statement.
SELECT ... FOR ALL ENTRIES IN itab WHERE cond returns the union of the solution sets of all SELECT
statements that would result if you wrote a separate statement for each line of the internal table replacing the symbol
itab-f with the corresponding value of component f in the WHERE condition.Duplicates are discarded from the result
set. If the internal table itab does not contain any entries, the system treats the statement as though there were
no WHERE cond condition, and selects all records (in the current client).
for example:
SELECT * FROM sflight INTO wa_sflight
FOR ALL ENTRIES IN ftab
WHERE CARRID = ftab-carrid AND
CONNID = ftab-connid AND
fldate = '20010228'.
this condition, return all entries of the sflight
hen using FOR ALL ENTRIES the number of matching records is restricted to the number of records in the internal table. If the number of records in the database tables is too large then join would cause overheads in performance. Additionally a JOIN bypasses the table buffering.
So for all entries is used for filtering out the data from the two tables based on the entries in them.
Advantages:
1) For all entries avoids inner join & so the performance increases.
2) For specified values in 1 itab, if you to fetch values from other table you can use it.
3) Use of select stmt in loop is gets avoided, as u can use read statement on the the new itab.

What is the Tcodes for Uploading of data using BDC & CATT

PP members:
I was going through the cutover activities , and what I understood is we transfer all the legacy system data into SAP before going live
The data upload follows certain steps (depends on the organizational design load strategies)
First we upload all the master data ( material master, BOM, W/C's & Routings)
Then the transaction data ( Ideally speaking, there should no open orders i.e. WIP as on the day of cutoff )
If the WIP (Work in Process) is unavoidable then the materials consumed shall be treated as materials of the previous stage and necessary adjustments shall be made after cutover day
At this point, I could not able to understand what does the author mean materials of the previous stage
Now comming to the uploading of data into SAP from legacy system, we use tools like LSMW, CATT & BDC
Is it a must to use only LSMW tool to upload master data or any other upload tools are fine
Lastly,. I am not sure about the Tcode of CATT & BDC
Summary of the questions:
1.What does the author mean material of previous stage, for WIP materials during cutover activities
2. Is it mandatory to use only LSMW tool for uploading for master data
3. What are the Tcodes for upload tools CATT & BDC ?
Thanks for your time
Suren R

Dear,
1.What does the author mean material of previous stage, for WIP materials during cutover activities - as i understood, what is the stage of material..like it must have gone through 2 work centers and other 2 is left. i.e. you need to create Production order with only 2 operation as other 2 is already over. - usually it is done in such a way that we will create Production order and confirm till 2 operations and WIp is calculated so thatb FI will tally the books in SAP and lagacy.
2. Is it mandatory to use only LSMW tool for uploading for master data - no you can use any tool as required and suits yr requirement
3. What are the Tcodes for upload tools CATT & BDC- BDC through a prog in SE38. CATT through - SCEM.

My ipod nano 6th gen fell out of my pockey and the screen cracked badly, is there any coverage for this under warranty? I just bought it a month ago. If not what are the options for getting it fixed

My ipod nano 6th gen fell out of my pocket and the screen cracked badly, is there any coverage for this under warranty? I just bought it a month ago. If not what are the options for getting it fixed? It is pretty frustrating, it fell from about 3 feet out of my pocket and now looks like it was beaten by a hammer.

Debbie:
deborahfromwindsor wrote:
he advises restarting by inserting the OSX disc and pressing down the C button to reboot from there then selecting disk utility, hard disk and repair.... Does he mean me to hold down the C key on the alpha keyboard or the ctrl key?
Should I just ask for my money back??? If it is a simple repair do I just literally push the disc in, push the power button and hold down the C button?
That's where I would begin, too, with
Repair Disk
Insert Installer disk and Restart, holding down the "C" key until grey Apple appears.
Go to Installer menu (Panther and earlier) or Utilities menu (Tiger) and launch Disk Utility.
Select your HDD (manufacturer ID) in the left panel.
Select First Aid in the Main panel.
(Check S.M.A.R.TStatus of HDD at the bottom of right panel, and report if it saysanything but Verified)
Click Repair Disk on the bottom right.
If DU reports disk does not need repairs quit DU and restart.
If DU reports errors Repair again and again until DU reports disk is repaired.
If DU reports errors it cannot repair you will need touse autility like TechTool Pro,Drive Geniusor DiskWarrior
First we need to determine if the issue you are experiencing with the computer is software or hardware based. Once we have gotten things sorted out there should be time enough to make you decision about keeping or returning it.
cornelius

What is the query for Accounts Payable Trial Balance (APXTRBAL) in 11.5.10?

Hi Guys,
What is the query for Accounts Payable Trial Balance (APXTRBAL) in 11.5.10?
I have to write an AP Invoice Aging Report in Discoverer to show all unpaid invoices that have been transferred into GL... Business wants it to match one-to-one with the AP Trial Balance standard report...
Business wants to run the report for any date in a past...
The report has two parameters:
As Of Date - the same as As of Date for the AP Trial Report
Trial Balance Run Date - the date when Trial Balance was run...
Conditions are:
TRUNC(Invoice Date) <=TRUNC(NVL(TO_DATE(:As Of Date),SYSDATE))
TRUNC(NVL(Payment Date,'01-JAN-5000')) > TRUNC(NVL(TO_DATE(:As Of Date),SYSDATE))
TRUNC(Invoice Creation Date) <= TRUNC(NVL(TO_DATE(:Trial Balance Run Date),SYSDATE))
Distr Accounting Date <= TRUNC(NVL(TO_DATE(:As Of Date),SYSDATE))
NVL(Distr Creation Date,Invoice Creation Date) <= TRUNC(NVL(TO_DATE(:Trial Balance Run Date),SYSDATE))
Show_Flag = 'YES', where:
Show_Flag = CASE WHEN ( NVL(Cancelled Date,'01-JAN-1901') > NVL(:As Of Date,SYSDATE) AND NVL(Inv Amount Aud,0) = 0 ) THEN 'YES' ELSE ( CASE WHEN NVL(Inv Amount Aud,0) = 0 THEN 'NO' ELSE 'YES' END ) END
There is a difference between the logic of my report, and the logic of AP Trial Balance...
Could you please advise what I'm missing?
Thanks,
Iana

What is the query for Accounts Payable Trial Balance (APXTRBAL) in 11.5.10? You can get the code by opening the report in Reports Builder and get the query.
Or, enable trace/debug as per (FAQ: Common Tracing Techniques within the Oracle Applications 11i/R12 [ID 296559.1]).
Thanks,
Hussein

What is the number for Verizon Wireless Corporate Customer Service Complaint for CA

My Complaint: I have been a Verizon Wireless customer for approx 20 years. I called customer service to seek an early upgrade for my daughter's phone. She is away in college and her phone is malfunctioning. She is eligible for an upgrade in approx 6 weeks so I did not want to spend the money on a replacement phone when since we were planning on updating to something newer. The customer service rep to me they could not do the early upgrade an to call back in a few weeks. After explaining this was unacceptable (I do not like the idea of a young female being out of state and away from home with no reliable means of communication), she places me on hold to later return with the only offer of I must purchase a new device through her ( over the phone) which will be shipped to me, the phone was priced $100.00 more than the online price (they will not price match), plus i must pay $30.00 upgrade fee, $35.00 activation fee and taxes on the retail price of the phone. I am upset and disappointed with the quality of service provided by Verizon being a 20 year customer. If not for the seriousness and urgency of this matter, i would not have asked for an early upgrade. It is times such as these that you get to see how much of a "valued customer" you really are. I guess you are valued as long as you pay your bill and continually purchase their products. I would like to speak with someone from Verizon's corporate or customer relations department. As of now I am really considering changing my service to a different provider. I have multiple accounts with Verizon and i will canx each after the current contract committment expire (starting with my daughter's phone which expires in 6 weeks) In the meantime I will go purchase her a new phone with someone else and take comfort knowing she will have reliable communication.

I started with them in 1985. It has been wonderful service but very expensive. They seem to operate on day of deposit day of withdrawal. That means that I have no benefits nothing beyond the normal customer if I don't pay my bill they shut me off. That's why I have switch to another provider and I have better service lower cost and better phones. you can't beat other providers I mean it. Please don't expect more from verizon other than a "pay me more money and I'll do what you want" because it's all about money. Read the transcripts from current Verizon employees all over the internet. The company is going down and they're taking customers with them.
msvat <[email protected]> wrote:
msvat created the discussion
"What is the number for Verizon Wireless Corporate Customer Service Complaint for CA"
To view the discussion, visit: https://community.verizonwireless.com/message/1113982#1113982
>

In Address Book, Lion, what are the checkmarks for when you Edit a Contact?

In Address Book for Lion, when you are in the Add/Edit a Contact window, what are the checkboxes for?

I am not seeing any checkboxes when I edit in Address Book in Lion, can you take a screen shot (Shift Command 4) of what you're seeing and post it?
BTW please fill out your profile (under Your Stuff above) so we know what machine and version of Lion you're using.

What is the procedure for a hard boot of my iPod touch 4th generation without itunes, and without computer, and without iPod data screen.?

What is the procedure for a hard boot of my iPod touch 4th generation
without iTunes, and without computer, and without iPod data screen?
6 months after purchase I updated my iPod touch as recommend by iTunes.
It has not worked since that day. It frozen (disabled) with a "connect to
iTunes" icon displayed...that is the only thing it does. itunes does not
recognize the iPod. My Windows7 computer recognizes an Apple device.
Other computers recognize the devise but if iTunes resided on that
computer it did not recognize the iPod
I suffered a setback with deep depression and am just now getting out of it enough to do something. The depression prohibited me from taking action.
I have done every procedure recommended from Apple help and external
sources. I did this thoroughly with help for other owners and IT experts,
Apple employees etc etc. I and associates have perform reboots utilizing a
number procedure using only button on the iPod. These were unsuccessful
also have performed.
Please do not ask me to do the usual.
Online I saw a process using the buttons on the iPod to completely
reformat
the iPod. It was NOT the hold buttons for 10 sec let go of one wait 8 sec
etc. I can not find the process now...a friend showed it to me in passing
I have lost contact with him. This is the procedure, I believe, that with
enable me to update and use the iPod.

You need an internet connection and likely a computer with iTunes but an iPhone, iPad or iPod touch with the FindMy iPhone App may work by:
If you previously turned on FIndMyiPod on the iPod in Settings>iCloud and wifi is on and connected go to iCloud: Find My iPhone, sign in and go to FIndMyiPhone and use Remote Wipe to erase the contents of your device. If you have been using iCloud to back up, you may be able to restore the most recent backup to reset the passcode after the device has been erased.
You can also wipe the iOS device by installing the FindMyiPhone app on another iOS device and using that app to wipe the device.
Otherwise
Disabled
Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
iOS: Forgot passcode or device disabled
If recovery mode does not work try DFU mode.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
For how to restore:
iTunes: Restoring iOS software
To restore from backup see:
iOS: Back up and restore your iOS device with iCloud or iTunes
If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
You can redownload most iTunes purchases by:
Downloading past purchases from the App Store, iBookstore, and iTunes Store
If problem what happens or does not happen and when in the instructions? When you successfully get the iPod in recovery mode and connect to computer iTunes should say it found an iPod in recovery mode.
Yo may have to go to an Apple store or a friend's house with an internet connection and iTunes.

TS1702 I use iphone5, I see an app update on the app store. but when App store and click on the update tab, it doesn't show me which application to update.. just give me a blank page.!!!! what is the solution for this.!!!!

I use iphone5, I see an app update on the app store. but when App store and click on the update tab, it doesn't show me which application to update.. just gives me a blank page.!!!! I wouldn't able to know what app has to be updated, untill and unless i get check for each every app on the app store installed on my iphone... what is the solution for this.!!!! can any1 one help me out.!!!!

Cc2528 wrote:
The iTunes Store on my iPad is set up with all my music already. And at the very bottom it shows my apple Id username. The only place it shows the previous owners id is in the App Store...
You can probably change the ID in the "iTunes and App stores" settings on the iPad....click on the wrong account ID , select sign out, then log in with your own ID, I have not done this but I think it works.....
but I would be more inclined to to the factory reset and start afresh.

What is the alternative for DisplayMemberPath="Value" for Windows Store applications?

I think there is a bug with Windows Store Applications when it comes to using DisplayMemberPath="Value".
Here is my code
<ComboBox Height="40" VerticalAlignment="Stretch" SelectedValuePath="Key" DisplayMemberPath="Value" x:Name="comboBox1" FontSize="25"/>
var source = new Dictionary<string, double>();
source.Add("Item1", 0.4);
source.Add("Item2", 0.3);
source.Add("Item3", 0.1);
source.Add("Item4", 0.1);
var formateDSource = new Dictionary<string, string>();
foreach (var item in source)
formateDSource.Add(string.Format("[{0}, {1}]", item.Key, item.Value), item.Key);
comboBox1.ItemsSource = source;
If you use this code in WPF in works perfectly. However if you use this code in a Windows Store Application then the Combo Box is empty and an error is thrown. So is there an alternative way to do this in Windows Store Applications and have I unearthed a
bug? Because I have researched the Web for days and found no solution to this.*please do not comment unless you have tried my code as a Windows Store App not a WPF in Visual Studios. Can Someone post an example based on my code that works in Windows Store
Apps please because this is terrible.
Thanks

It looks like you got an answer on SO:
http://stackoverflow.com/questions/29817124/what-is-the-alternative-for-displaymemberpath-value-for-windows-store-applicat
This does look like a bug.
Matt Small - Microsoft Escalation Engineer - Forum Moderator
If my reply answers your question, please mark this post as answered.
NOTE: If I ask for code, please provide something that I can drop directly into a project and run (including XAML), or an actual application project. I'm trying to help a lot of people, so I don't have time to figure out weird snippets with undefined
objects and unknown namespaces.

What is the algorithmn for smoothing filtering in Filter VI?

Similar Messages

Maybe you are looking for