What is the best configuration for XP on a MacPro?

Situation: Macpro (the old one)
3 hardrives; 1st is the Mac OSX HD
2nd Windows XP
3rd Extra Data
this is how my setup is, but i notice my computer makes a louder noise as before, why is this?
would you recommend this setup or install XP on the same drive as Mac OSX?
which one works best?

Hi Dion,
when you had OSX and Windows on one HD, was this the only HD in your Mac Pro or do you had all three HDs back then too ?
Cause the more HDs you have in your MAc Pro, the more heat they produce, which can result in higher fan speeds and/or a more often up-spin of the fans.
The startup of XP (after the 'Option'-key choice) is indeed rather slow, at least much slower than OSX.
My guess is that the BIOS-to-EFI emulation that OSX makes to enable XP to boot is taking some time.
XP is only using the HD on which it is installed, because the other HDs are unknown to it, unless you use something like MacDrive to access your OSX partitions while in XP.
And since the energy-saving features of your Mac Pro used with OSX are mostly unknown to XP (due to lack of appropriate drivers) it is possible, that the fans are running more often and/or at higher speeds than they do in OSX.
Stefan

Similar Messages

What is the best configuration for 2 AP's Broadcasting? same SSID/channel?

So i have 2 WRT54G version 2.0 wireless routers. They are not doing DHCP for my home network, i have another device (Sonicwall Firewall) that is taking care of that. Originally I had 1 wireless router (acting as just an access point, but I now have an additional one and want to add it to extend wireless coverage.
My question is this. How do i make it so that laptops can roam around my house and switch from AP to AP depending on which one has the best signal? Is this possible?
I figure that i would have to obviously disable DHCP on each router. But what about SSID's. Can they be the same? What channel should i use, the same for both, or different channels?
Any help would be awesome, Thank you!
-Aaron

For a roaming network both access points must have the identical SSID and identical security settings. Regarding the channel it is difficult to say. They should be different as broadcasting on the same channel creates interference. Better whould be to use non over-lapping channels, e.g. channel 1 & 6. The problem, however, are the clients. Some clients have difficulty with roaming across channels.
I had two access points with channel 1 & 6. My laptop worked fine in all locations with interruption. However, my WiFi-IP-Phone had troubles. It seems to search the channels from 1 up, thus I was able to roam from channel 1 to 6 but never back. The phone just disconnected.
So, I would recommend to use different channels and test if your clients can roam without problems. If you'll find that one does not properly work try to put them on the same channel. Also: be patient when changing the configuration. I would even recommend to power cycle the router after each change of channel as well as the client. In the beginning I never did that and very often it did not work in the beginning but after an hour it work. I suppose this was because I was using WPA2 and some problems due to the rotation encryption keys WPA2 is using...

Netgear Stora, what is the best configuration for smooth operation

I have a Netgear stora, and I know how to configure the best possible way this system for Mac NAS. It always gives me problems and the NAS system invites me to visit the Apple community.
In Windows XP system and Windows 7 works correctly.
Can you help please, I do not know if you need another type of program, or if my mac must have a particular program to work or any particular update, since this update to version 10.7.4.
Thank you very much.

thanks Rick
what about the differences in the two processor
options.
is there really a noticeable difference?
thanks
niko
I seriously doubt that there would be. My 2.16Ghz iMac is plenty fast and I doubt that most people would be able to tell the difference between it and the 2.33. By FAR the most important upgrade is RAM. Don't get the extra RAM from Apple though -- it's too expensive and the RAM is easily upgradeable. Buy it from Crucial and install it yourself. I got 2 gigs from them for $85 plus shipping. Just remember, there are only 2 RAM slots so if you want to max it out at 3 gigs you will have to get a 2 gig stick and a 1 gig.

What is the Best Configuration for using SSD & HDD Internal Drives in iMac?

Hi,
I have a Refurbished 2011 21.5" iMac. It came with a 1TB HDD. I had a 120GB SSD custom installed by Other World Computing. I would like to reap the speed benefits of having the OS and applications reside on the SSD and having most of my heavy, frequently used data on the HDD. I've considered simply going the route of changing the advanced settings of my user configuration so that my home directory is located on the HDD. I've read this is an ok solution, but that there may be better ways to do this to get the best out of the available speed of the SSD. Could anyone recommend better options?
For reference, I use apps like Photoshop Lightroom, the NIK suite of photo editing applications and Photoshop CS6 pretty heavily. I don't do much movie editing or production...only occasional slideshows in iMovie...although I do keep a lot of old, imported, video footage of my kids on my HDD and on my backup system.
Thanks,
Ben Shugart

Start with the only Apple doc I could find: http://support.apple.com/kb/ht5446. They tout the technology, but don't provide much in terms of help.

What's the best configuration for a 300+ GB music library?

I'm about to buy an iMac. I want iTunes to run seamlessly. Assuming I purchase the 20" what else should I include? 2 or 2.4 GHz? 1 or 2 GB of Ram? How much internal HD space? I am happy to consider purchasing external HD space. I will be using it mostly for word processing and some low-tech music/video editing. Thanks in advance.

Before I got my new iMac (20" 2.4 ghz) I had my music library, which is about 50 gigs stored on a LaCie external hard drive connected through FireWire 400 and had no problems. As for your other question your LaCie hard drive (like mine it seems, just checked system monitor) may only be capable of 400mb/sec. I'm not sure about their new hard drives but mine is a little more than a year old so this may be the case with yours as well.
Time machine is apple's system backup program.
Message was edited by: abriggsknox
Message was edited by: abriggsknox

I will be buying the new IMac 27 inch in December. Would like input on the best configuration for photographic and possibly video processing-dream machine!

I will be buying an IMac 27 inch in December. What is the best configuration for photo and possibly video processing.Does one need a Mac Pro? Dream machine!

Just to explain what I just wrote to Laundry Bleach:
Why is there no iDVD on my new Mac?
https://discussions.apple.com/docs/DOC-3673
UPDATE & ADDENDUM:
But even though you can still buy iLife 11 that includes iDVD 7 from Amazon, Apple now make it difficult to install:
Poster jhb21939 posted this in another thread:
“when I attempted to load iDVD into a new iMac. A notice came up on the screen stating that the 'Authorisation Licence' had expired on 25 March this year (2012).
I contacted the Apple support team and eventually, I was told that the Licence had been withdrawn and could no longer be used.”
In other words Apple are now so adamant that we don’t use iDVD that they have tried to make it impossible to install.
In response, Old Toad posted this solution:
“You can still use it one all of your Macs. If you get an invalid certificate message just set your Mac's clock to sometime before early 2011 and run the installer. After you're done reset the time back to the correct time.” He added this comment:
“It began after iDVD and iWeb were discontued and they were dropped from the Apple Store. All I can think of is the certificate was set to expire after a certain time period after the intitial iLife disc was released.
I've been able to use the installer even without setting back the date. I just clicked on the Continue button and it would work as expected. For some it would not continue unless the date was set back.”
The latest anorexic iMacs just announced do not even include a CD drive! Proof positive that Apple virtually prohibit the use of DVDs - although the newly announced Mac Minis do include a Superdrive.
Yet, they still include iMovie! Heaven alone knows or understands what you are supposed to do with your newly edited masterpiece - except make a low quality version for YouTube?

What are the best practice for CQ5.5 configuration?

Hello,
What are the best practice for CQ5.5 configuration which handle for High availability.
Last time I had a issues on server when I was uploaded 2 GB of DAM and then after that the server is not able to start and always getting error regarding Tar Persistance.
So kindly request you to please let me know what are the best apache felix configuration.
Thanks in advance...
Regards,
Satish

Hi,
A DAM upload, regardless of the size of the assets, never should result in TarPM problems, unless you run into an OOM, which left the repository in an unclean state. So if you regularly do DAM uploads of that size, you should check the Garbage Collection logs and probably adjust the heapsize if necessary. You might want to limit the number of concurrent running workflows to keep the memory consumption a bit lower.
To your question: HA in a traditional sense you cannot achieve with a single box, even with optimized settings. In an author usecase you would need clustering.
Jörg

What is the best Monitor for Video editing & Graphic Design?

Hi every one,
I would like to find out what is the best monitor for video editing and graphic design that you recomend, I am trying to buy one but not sure which one is good and not expansive.
Thanks very much

I don't want 2 monitors, so a single 27inch model just what I need... plenty of room for PPro, or I can have a Word document and a Text file open and side by side
John,
That is personal taste and there is no discussing taste. However, from my perspective, and that is personal, I prefer 3840 x 1080 resolution with dual monitors over 1920 x 1080 with a single monitor, but that is because I very often have Firefox, Filezilla, Dreamweaver and some other applications open at the same time, switching between the Adobe forums, Gmail accounts, Notebook results from the PPBM5 data submissions, PPBM5 form submissions, MySQL access, phpadmin pages to update the database, the PPBM5 results pages and various DW .php pages for the maintenance of our database and switching back and forth between various versions of PR. I occasionally really run out of real estate with all these applications and could not consider a single monitor with only 1920 x 1080 resolution, even if it were a 105" screen. In the future I would even like to have a four monitor setup (with MPE hardware support) in a two by two configuration, so that I can freely move my application screens around.
If that happens, notice I say if and not when, my preference for a monitor would be something like 4 Samsung F2380 monitors. Small bezel, great display and panel, affordable.

What is the best choice for our project? Thanks

We are a startup company and developing a webiste with two mobile app.
We use PHP in the server side and write with a private framework.
We don't want to use any host-specific APIs so that we can move to other cloud server easily.
In our case, can we use Website option in Azure?
If the answer is yes. What is the best choice for us, VM or website? We need scalability in the future.
Thanks!

hi,
It depends on your requirement. Base on my experience, VM or website all could meet your requirement. From your description, You could use azure website to host your php website (http://www.windowsazure.com/en-us/documentation/articles/web-sites-php-configure/).
And you could use website auto scale feature in the future. I suggest you could see their comparison (http://www.windowsazure.com/en-us/documentation/articles/choose-web-site-cloud-service-vm/
Hope it helps.
Regards,
Will
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

What is the best app for Maintenance/Cleanup for my mac? Do I need Virus Protection?

What is the best app for Maintenance/Cleanup for my Mac? Do I need Virus protection?

How to maintain a Mac
Make two or more backups of all your files
One backup is not enough to be safe. A copy of a backup doesn't count as another backup; all backups must be made directly from the original data.
Keep at least one backup off site at all times in case of disaster. Backing up to a cloud-data service is one way to accomplish this, but don't rely exclusively on such backups.
In fact, don’t rely exclusively on any single backup method, such as Time Machine.
If you get an indication that a backup has failed, don't ignore it.
Keep your software up to date
In the App Store or Software Update preference pane (depending on the OS version), you can configure automatic notifications of updates to OS X and other Mac App Store products. Some third-party applications from other sources have a similar feature, if you don’t mind letting them phone home. Otherwise you have to check yourself on a regular basis.
Keeping up to date is especially important for complex software that modifies the operating system, such as device drivers. Don't install such modifications unless they're absolutely necessary. Remove them when they are no longer needed. Before installing any Apple update, you must check that all system modifications that you use are compatible. Incompatibility with third-party software is by far the most common cause of difficulties with system updates.
Don't install crapware
...such as “themes,” "haxies," “add-ons,” “toolbars,” “enhancers," “optimizers,” “accelerators,” "boosters," “extenders,” “cleaners,” "doctors," "tune-ups," “defragmenters,” “firewalls,” "barriers," “guardians,” “defenders,” “protectors,” most “plugins,” commercial "virus scanners,” "disk tools," or "utilities." With very few exceptions, such stuff is useless or worse than useless. Above all, avoid any software that purports to change the look and feel of the user interface.
It's not much of an exaggeration to say that the whole "utility" software industry for the Mac is a fraud on consumers. The most extreme examples are the "CleanMyMac," "TuneUpMyMac," and “MacKeeper” scams, but there are many others.
As a rule, you should avoid software that changes the way other software works. Plugins for Photoshop and similar programs are an obvious exception to this rule. Safari extensions, and perhaps the equivalent for other web browsers, are a partial exception. Most are safe, and they're easy to get rid of if they don't work. Some may cause the browser to crash or otherwise malfunction. Some are malicious. Use with caution, and install only well-known extensions from relatively trustworthy sources, such as the Safari Extensions Gallery.
Only install software that is useful to you, not (as you imagine) to the computer. For example, a word processor is useful for writing. A video editor is useful for making movies. A game is useful for fun. But a "cache cleaner" isn't useful for anything. You didn't buy a computer so you could clean caches.
Never install any third-party software unless you know how to uninstall it. Otherwise you may create problems that are very hard to solve. Do not rely on "utilities" such as "AppCleaner" and the like that purport to remove software.
Don't install bad, conflicting, or unnecessary fonts
Whenever you install new fonts, use the validation feature of the built-in Font Book application to make sure the fonts aren't defective and don't conflict with each other or with others that you already have. See the built-in help and this support article for instructions.
Deactivate or remove fonts that you don't really need to speed up application launching.
Avoid malware
"Malware" is malicious software that circulates on the Internet. This kind of attack on OS X was once so rare that it was hardly a concern, but it's now increasingly common and dangerous.
There is some built-in protection against malware, but you can’t rely on it—the attackers are always at least one day ahead of the defense. You can’t rely on third-party "anti-virus" products for protection either. What you can rely on is common-sense awareness—not paranoia, which only makes you more vulnerable.
Never install software from an untrustworthy or unknown source. If in doubt, do some research. Any website that prompts you to install a “codec” or “plugin” that comes from the same site, or an unknown site, is untrustworthy. Software with a corporate brand, such as Adobe Flash Player, must come directly from the developer's website. No intermediary is acceptable, and don’t trust links unless you know how to parse them. Any file that is automatically downloaded from the web, without your having requested it, should go straight into the Trash. A web page that tells you that your computer has a “virus,” or that anything else is wrong with it, is a scam.
In OS X 10.7.5 or later, downloaded applications and Installer packages that have not been digitally signed by a developer registered with Apple are blocked from loading by default. The block can be overridden, but think carefully before you do so.
Because of recurring security issues in Java, it’s best to disable it in your web browsers, if it’s installed. Few websites have Java content nowadays, so you won’t be missing much. This action is mandatory if you’re running any version of OS X older than 10.6.8 with the latest Java update. Note: Java has nothing to do with JavaScript, despite the similar names. Don't install Java unless you're sure you need it. Most people don't.
Don't fill up your disk or SSD
A common mistake is adding more and more large files to your home folder until you start to get warnings that you're out of space, which may be followed in short order by a startup failure. This is more prone to happen on the newer Macs that come with an internal SSD instead of the traditional hard drive. The drive can be very nearly full before you become aware of the problem.
While it's not true that you should or must keep any particular percentage of space free, you should monitor your storage use and make sure you're not in immediate danger of using it up. According to Apple documentation, you need at least 9 GB of free space on the startup volume for normal operation.
If storage space is running low, use a tool such as OmniDiskSweeper to explore the volume and find out what's taking up the most space. Move seldom-used large files to secondary storage.
Relax, don’t do it
Besides the above, no routine maintenance is necessary or beneficial for the vast majority of users; specifically not “cleaning caches,” “zapping the PRAM,” "resetting the SMC," “rebuilding the directory,” "defragmenting the drive," “running periodic scripts,” “dumping logs,” "deleting temp files," “scanning for viruses,” "purging memory," "checking for bad blocks," "testing the hardware," or “repairing permissions.” Such measures are either completely pointless or are useful only for solving problems, not for prevention.
To use a Mac effectively, you have to free yourself from the Windows mindset that every computer needs regular downtime for maintenance such as "defragging" and "registry cleaning." Those concepts do not apply to the Mac platform.
A well-designed computing device is not something you should have to think about much. It should be an almost transparent medium through which you communicate, work, and play. If you want a machine that needs a lot of attention just to keep going, use a PC, or collect antique cars.
The very height of futility is running an expensive third-party application called “Disk Warrior” when nothing is wrong, or even when something is wrong and you have backups, which you must have. Disk Warrior is a data-salvage tool, not a maintenance tool, and you will never need it if your backups are adequate. Don’t waste money on it or anything like it.

I have problems in the initiation of the Encore process when opening presents the following error message : "Encore CS6 Cannot Run in Non-Royalty Serialized".... What is the best solution for this problem ?

Help Me.
What is the best solution for this problem ?

Encore is activated when you activate Premiere Pro... so, as Stan asked, how did you install P-Pro?
Ask for serial number http://forums.adobe.com/thread/1234635 has a FAQ link
-and a fix for Encore http://forums.adobe.com/thread/1421765?tstart=0 in reply #7
-plus more Encore http://helpx.adobe.com/encore/kb/cant-write-image-fie-larger1.html

What are the best practies for naming symbols (spaces OK,etc.)?

What are the best practices for symbol naming for ease, flexibility, & to avoid "gatchas" down the road?
Does it make any difference if one includes spaces in the names of symbols? Are there any widely followed conventions for naming them like using camelCase or underscores?
Thanks!

Hi Gina D 3333,
Best-practice file-naming conventions for PDF files are the same as for any other file. I found this article on Apple's website that contains some useful pointers to consider when you're naming files that will be used on multiple platforms: OS X: Cross-platform filename best practices and conventions
I hope this helps!
Best,
Sara

What is the best practice for changing view states?

I have a component with two Pie Charts that display
percentages at two specific dates (think start and end values).
But, I have three views: Start Value only, End Value only, or show
Both. I am using a ToggleButtonBar to control the display. What is
the best practice for changing this kind of view state? Right now
(since this code was inherited), the view states are changed in an
ActionScript function which sets the visible and includeInLayout
properties on each Pie Chart based on the selectedIndex of the
ToggleButtonBar, but, this just doesn't seem like the best way to
do this - not very dynamic. I'd like to be able to change the state
based on the name of the selectedItem, in case the order of the
ToggleButtons changes, and since I am storing the name of the
selectedItem for future reference.
Would using States be better? If so, what would be the best
way to implement this?
Thanks.

I would stick with non-states, as I have always heard that
states are more for smaller components that need to change under
certain conditions, like a login screen that changes if the user
needs to register.
That said, if the UI of what you are dealing with is not
overly complex, and if it will not become overly complex, maybe
states is the way to go.
Looking at your code, I don't think you'll save much in terms
of lines of code.

What's the best photograph for a no background image?

I am about to photograph some products and would like to make a set up where I can photograph each of the products in the same setting/lighting. Then, when I go to open/edit them in PhotoshopCS4, I can take out the background and have just the image. Then, I can place that image ontop of any background I want. There is one bad thing. Some of these have a clear top where you can see thru them. Does or will that make a difference?
I want to set it up like they do for the weather on television, have a blue background and erase all of the blue showing. Then the only thing showing in the end is the digital background that was added in by computer and the weatherman(unless he's wearing a blue tie, in which case you can see the info through him). But my question still stands, what is the best setting for this and/or background color, how should the photographs be taken and then opened and edited(removing the background) using PhotoshopCS4?
We have a lighting set up, a 30" x 30" x 30" light tent setup, 3 lights with Pro Light Reflectors(one on the left, one on the right and one on top), 1 white and 1 black background and a box to place the images on. I'm using a Nikon D100.
Attached in a photo example.
This was taken with the black background and you can see the black through the bottle. I erased all of the surrounding black, but the dark shades still show on the sides.
Any help will be appreciated.
Sean

The whole point is that these photographs will be used for the book, manuals, magazines, ads... The backgrounds will not always be the same. That's my main problem. I am trying to figure out a way for the glass of the bottles to be "glass" images or "see through" so that when the photograph is placed on a background of, let's say, flowers, the flowers would show through. The edges of the glass are still solid and the flowers would not show thru them, but...
Is this type of thing possible for printing quality photographs?
Note - In the attched photo, it can be seen that the black background can be seen the plastic cap.

What's the best approach for handeling about 1300 connections in Oracle.

What's the best approach for handling about 1300 connections in Oracle 9i/10g through a Java application?
1.Using separate schema s for various type users(We can store only relevant data with a particular schema. Then No. of records per table can be reduced by replicating tables but we have to maintain all data with a another schema Then we need update two schema s for a given session.Because we maintain separate scheama for a one user and another schema for all data and then there may be Updating problems)
OR
2. Using single schema for all users.
Note: All users may access the same tables and there may be lot of records than previous case.
What is the Best case.
Please give Your valuable ideas

It is a true but i want a solution from you all.I want you to tell me how to fix my friends car.

What is the best configuration for XP on a MacPro?

Similar Messages

Maybe you are looking for