What is the best way to connect time capsule to bt infinity

I have bt infinity and want to connect my time capsual to it does anybody know what configuration would get the best connection?

I have just had Infinity installed and also have a time capsule.
The way I have set it up is as follows:
Get rid of the HomeHub they provide (to save electricity).
Need to keep the VDSL2 modem (the other box that plugs into the phone socket).
Plug the VDSL modem into the time capsule WAN port directly.
Go into time capsule manual setup via the airport utility
On the internet settings tab:
Connect Using select PPPoE
Account Name enter '[email protected]'
Password and verify password enter a single space (as in press the space bar once). There is no password, but for some reason it will not accept no password at all, and won't negotiate properly.
I don't have a service name set, and 'connection' is set to always on' with 'disconnect if idle' set to never.
Works perfect, I then use the time capsule as the wifi hub and all my devices connect to this.

Similar Messages

What is the best way to extend time capsule range?

Hello there:
I was wondering what kind of set up do people have in their house to ensure a good coverage all around the house? I've tried several options and none seems to work correctly. I've tried Time capsule + airport base, I've tried two time capsules, but didn't get too far.
Thoughts?

Do you get good coverage all around your house? how big is your house?
The size of the house is not really the issue nearly as much as the obstructions in the signal path. For example, a wireless signal will easily travel 100 feet with no obstructions slowing down the signal.
A "typical" wall of sheetrock and 2 x 4s in a home will on average, absorb about 15-20% of the signal. So, with 3-4 walls in the signal path, it is not hard to understand why a signal will likely be much weaker at the other end of the house, or at the point where you add an "extending" device.
A ceiling is usually about twice the thickness of an average wall or more, so you'll have to take that into account as well if you have multiple stories.
The "extending" device can only repeat the signal that it receives, so if it gets a weak signal, it "extends" a weak signal.
The "best" way to extend is connect the two wireless devices using an Ethernet cable, which may not be easy depending on the construction of the home, but it is by far, the "best" way to provide more wireless coverage to remote areas that need it.

What's the best way to use Time Capsule through Extended Wireless Network?

I am operating four computers, three Apples and a PC. All the Apples use Snow Leopard. I have a large house where the cable company's modem and internet access is located downstairs at the far back of the house. That is where I have a 2Tb 802.11n Time Capsule (TC) connected to the modem by ethernet cable. My iMac is there, connected to the TC by ethernet cable. In the middle of the house, also downstairs, I have an Airport Extreme (802.11n) operating as a wireless bridge. Upstairs in the front of the house (very far from the TC and closer but not very close to the AE) I have a home office. That is where my other two Apples--a MacBook Pro and a MacBook Air--are usually located. The PC is located in a bedroom directly above the TC and wirelessly connects to it. At all locations, I get four radio signal strength bars. However, I am not sure that the AE is doing anything, because I get four bars regardless of whether the AE is plugged in, or not. When it is turned on, Airport Utility on all computers shows both the TC and the AE, but I have not been able to find which Airport ID I am actually connected to.
From my home office I do temporarily lose my internet connection from time to time each day, but the connection recovers usually within seconds. I assume this reflects occasional interference or other loss of wireless signal in the distant home office, although I do not see the radio bars diminish to less than the four bars.
All three Apples are set up to use the same TC for backup into Time Machine. However, I have been getting errors on the laptops operating in the home office (a long way from the TC and perhaps connecting directly over wireless or perhaps wirelessly through the AE bridge. Some messages are to the effect of being unable to backup, and others more recently report errors. I think that either due to connection interruptions or merely by suspending or turning off the computer while in the middle of backing up, errors in the Time Machine files were created. I have been unable to delete more than a few of the 8Mb sparsebundle bands so that I can completely get rid of one of the sparsebundles for the MacBook Pro. I was able to get rid of the other sparsebundle for that computer and also the sparsebundle for the MacBook Air. I am reluctant to erase the entire TC, because it has been working for the directly connected (by ethernet cable) iMac sitting right next to the TC.
So, I am wondering what is the experience of others who are trying to use TC successfully from computers located a long distance from the TC with either a direct wireless connection or a bridged wireless connection through an AE or other bridge.
And does anyone have good ideas about how to delete the sparsebundles effectively? I read the various questions and answers in the support community, but so far nothing that I have tried based on those messages seems to work. It seems that when all the Time Machines are set to "Off" and the sparsebundles are expanded to show the individual bands, we ought to be able to delete them fairly expeditiously. Sometimes, I can delete one band fairly quickly, but then the second band will hang forever. More often, I can't even delete the first band.

Thank you, Bob. I followed the procedure you stated. My AE is working. I did register its BSSID when I put my laptop next to it. This is also the BBSID I am getting when in my home office at the far end of the house from the TC. This means I am using the extended bridge AE when working and trying to use the automated backup feature in Time Machine. Do you think I should turn off Time Machine on these laptops when they are in the home office, and bring them into the room with the TC occasionally to have a better connection (wireless to TC or by connecting an ethernet cable) when trying to make Time Machine backups for them?
Interestingly (in contrast to the exact match of BBSID's for my AE), when I compared the BSSID for my TC in Airport Utility to the BBSID of the TC using the option key and the fan shaped Airport icon, the BBSID's matched except for the last two digits. In Airport Utility, they are 2F. In the fan shaped Airport icon they are 30.
Also, the AE signal, being centrally located on the first floor of the house, seems to be the one most in use. When I walked my laptop away from the AE all the way back to the TC, the laptop automatically switched over to the TC only once. Most of the time, the laptop is still connecting wirelessly with the AE. To switch back to the TC, I have to turn Airport off, and then turn it back on again.
I don't know how efficient or inefficient the Time Machine is when connecting to the TC indirectly through an AE bridge.

What is the best way to connect a MacBook Pro to my HiFi system ?

Hi,
I'm new to Apple support communities having just bought my first Macbook Pro (a 17" 2.5GHz i7 model) and this is my very first community post.
Im a bit of a Hi-Fi enthusiast, so, with my new MacBook Pro I've taken the opportunity of completely reloading my iTunes library in high quality Apple Lossless format. Took a while but now I've completed the task Im pleased I've done it.
My question is, what is the best way to connect a Macbook Pro to a high quality Hi-Fi preamp - my Hi-fi system is musical Fidelity, and the pre amp (an A5 CR Pre amp) and this pre amp, which has superb audio quality, only has analogue phono inputs ?
I'm interested to understand what both the wired and wireless connection options are. I'm guessing one option must be to use the headphone output, but I have no idea if the output from the headphone socket on my new macbook (which is presumably designed to drive headphones) would be at a suitable level for a phono line level input ?
Ive also read a few comments about using digital connection - and my second question would be - what is the audio digital connection on my macbook ?
Aplogies if this question has been asked lots of times before but I've looked through some previous posts and can't find any answers in simple and straightforward language concentrating on the issue of connecting a MacBook Pro to an analogue phono pre amp input ?
Thanks in anticipation of some advice.

What is the best way to connect a MacBook Pro to my HiFi system?
Look at the back of the reciever and see what your connection options are, the front headphone jack is output usually.
The Mac's analog audio in/out ports doubles as a optical in/out ports.
The analog won't over power your amp, it's just a headphonejack, like a powered mic, just enough power to get the signal to the destination in one piece.
Since you have a analog amp, your stuck with inferior analog connections, however you mentioned you wish to listen to the best sound quality of your lossless music.
To do that your going to need a decent surround sound system with Toslink optical import jacks, a Toslink stereo jack to regular Toslink adapter, Toslink cable and enable the optical output in your System Preferences >Sound
Another method is to use a Airport Express, it also has duo analog/opical out port. Then set up the Airport Express for iTunes streaming using the Airport Utility, then in iTunes setup the lower right corner one can set the connection.
I recommned a Harmon Kardon surround sound system, with their 100 watt satelight speakers and the 200 watt subwoofer. Enable the "concert hall" and other neat effects which will turn your 2.0 (stereo) iTunes music into 4 channel speaker sound filling the room with music and sending the lower channels to the subwoofer.
It will likely bring tears to your eyes that you can actually hear the full quality of your music as intended, I almost quarranty you will never want listen to music on a crappy iPhone or iPod again.
If a surround sound system is out of your budget, you can get by using the Harmon Kardon "Go Play" portable stereo and a analog stereo cable.
If your going to use your analog amp to power reference speakers, then there are various analog adapters of all sorts to make the appropriate connections once you know what they are, check out Radio Shack online for them.

What's the best way to connect the audio out of my Mac to my stereo receiver?

I want to listen to my mp3 collection through my home theatre stero receiver.
I have 2 audio interfaces that I connect to my mac through USB and Firewire: Digi Design Mbox mini and Maudio ProFire 610.
I've tried going from a headphone 1/8'' connector from the headphone out of my mac to rca connected to the aux (or whatever) of my stereo.
I've tried using a 1/4'' adapter on the 1/8'' to go from my mbox mini's headphone output to the rca aux on my stereo.
The problem is I'm hearing distortions that sound like clipping, or static, crunchiness on certain frequencies in a lot of my mp3's that shouldn't be there.
I listen to lots of music, and a lot of it uses distortion, like shoegaze, drone etc but I know what I'm hearing is unnatural.
I even hear these flaws when I listen to headphones through the headphone out of my mbox.
Page 2 on this instruction manual says I should be able to go from the monitor outs to my stereo. The monitor outs are 1/4 inch out so I figured I would need a 1/4 inch to rca cable.
I got this one from monster thinking it should work. No dice.
So my question is, what is the best way to connect my mac to my stereo? I need to avoid these distortions and flaws in the audio i'm hearing or I will go nuts.
Why might I be getting these clipping distoritons?
any advice would be fantastic

It depends on how close the receiver is to the iMac. If it's just a few feet away you need at cable like:
http://www.amazon.com/StarTech-com-THINTOSMIN6-Toslink-Digital-Optical/dp/B00016 W6Y6/ref=sr_1_2?ie=UTF8&qid=1316096392&sr=8-2
However if the receiver is across the room or the house you would be best to enable Air Play, this enables you to wirelessly connect the receiver to the iMac. You will need the above cable and an Airport Express. If you are not familiar with Air Play navigate to:
http://www.apple.com/itunes/airplay/
I have been using it for quite some time and find it great. If you are not familiar with the Airport Express here is the link to it:
http://www.apple.com/airportexpress/
You can even find refurbished ones on Apples website for about $79.

What is the best way to connect my ipad to the high-speed Internet connection in a hotel room

what is the best way to connect my ipad to the high speed inernet connection in a hotel room

every connection is a bit different. Generally, connect to the wifi, then you may need to open Safari, and may even need to try to get to one of your bookmarked pages to trigger the 'agree to our terms' page to come up.
As to it kicking you off every so often, there are sometimes glitches with the wifi on iPads, you can also be subject to any programming the hotel has. Like I've noticed various places that only allow you to log on for a period of time before having to relogin.
most hotels have 1-800 numbers, so you can always try calling that to see if their tech support has any tips for the frequent disconnection issue.

What is the best way to connect my guitar to the usb port on my IMac

This is for use with Logic Pro X
what is the best way to connect my guitar to the usb port on my
I-Mac

As has been said really, the less you pay the less quality, and flexibility you'll have on your sound.
For example, you could run on a 'Rocksmith Real Tone Cable' if you just wanted a cheap way of getting your guitar into the computer for some fun. Probably cost you $30 (I live in UK so can't be sure). If you're starting out then this could be considered the best option for dipping your toe in the water without spending too much.
You won't get a really nasty sound out of that if you can process it yourself in Logic afterwards to clean up, but it won't be great either. I imagine it could get quite noisy so you'd need to get heavily gating your guitar sound, if you're playing something clean that's not ideal.
Longterm, you're far better getting a decent audio interface, as you need something to play sound back through, if you have different input sources you usually have to create an aggregrate device on osx to use multple sources at once esp if you're using the built in audio chip on your mac to listen.
All this can add latency and possibly sync issues (i.e. drum tracks not in time with audio etc.), although generally it's not too bad, but it's something worth knowing if you want to do things on the cheap without buying a dedicated interface.
What kind of money did you want to spend? Are you thinking super duper cheap, and then see how it goes and maybe spend more in future if you enjoy it? Personally i would say £100-150 would get your something good to start with, like that Presonus audiobox, there's a lot of options like that available.
My local music shop always push the alesis io2 on new users, gotta say i'm not that overly impressed with it. Line 6 stuff will be good however, but limiting. Although i beleive you get their software for free with it?

What's the best way to connect latest iphone to 2010 Mini CooperS for hands free

What is the best way to connect the latest iphone to a 2010 mini Cooper S for hands free operation?

Patrick Hindman wrote:
Does anyone have any suggestions of what kind of hardware I should purchase to do this? Basically, I want a jam-up iTunes server that serves everything to each device (sorry, should have worded it this way sooner! . Maybe a MacMini server would do it? Or possibly just a Mac Mini or would Time Capsule do something like this?
i use an old G4 Mac Mini running 10.5 Leopard, and it's on 24/7
it runs in headless mode (ie no monitor) and i remotely administer it using remote desktop (or logmein if i'm out the house).
i have a 1TB WD Mybook hanging off it connected via Firewire and that stores all my itunes content.

What is the best way to connect my new MBP to monitor - DVI, VGA or HDMI

What is the best way to connect my new MBP to a computer monitor? DVI, VGA or HDMI? Thanks

I recommend the Apple MiniDisplay Port to DVI adaptor. I would avoid VGA. MiniDisplay Port to HDMI will work as well (3rd party).
http://www.apple.com/search/?q=dvi%20adaptor&section=mac&geo=us

What is the best way to connect 2 monitors to a Mac Pro 13 inch (2013)?

What is the best way to connect 2 monitors to a Mac Pro 13 inch (2013)?

If you want to connect 2 Displays you must do it one with the Minidisplayport and one by HDMI if you have a Retina 13 Inch. i think the old MBP doenst have HDMi Out

What is the best way to connect MBP 13" - (non retina) to HDMI TV input

What is the best way to connect MBP 13" late 2012 - (non retina) to HDMI TV input
...To get Video and Audio? With one cable ...
I'm seeing that the "rocketfish" adapter is not handling the job (from these forums).
I enjoy watching youtube videos, hulu, etc on the big screen through my laptop. The other Windows laptops I'ved had from Sony, HP, Dell, all had HDMI and was easy peasy.
I don't have the patience to buy and return 10 different types of adaters (nor would Best Buy appreciate that)
Thank you!

Look for something like this:
http://www.amazon.com/Cable-Matters-Premium-DisplayPort-Thunderbolt/dp/B004CADY9 I/ref=sr_1_6?ie=UTF8&qid=1356715728&sr=8-6&keywords=cable+displayport+to+hdmi
Ciao.

What is the best way to connect PumpWorks to Labview? DDE or OPC

What is the best way to connect quizix PumpWorks to labview?
PumpWorks share data using Dynamic Data Exchange (DDE),what is the best way? To use an OPC Server betwen labveiw and pumpworks or DDE?
Solved!
Go to Solution.

Hi.
If the instrumet can communicate with an OPC server I think both methods are fairly equal.
There is a chance that you might have to reinstall LabVIEW without OPC server if you choose DDE, as it is known that it might conflict with the DDE server.
http://zone.ni.com/devzone/cda/tut/p/id/4531
http://zone.ni.com/devzone/cda/tut/p/id/7450
-Tom

What is the best way to connect a G4 running 9.2.2 or 10 to an new imac running lion?

What is the best way to connect a G4 running 9.2.2 or 10 to an new imac running lion?

It should be possible to network them easily.
Ethernet will be the most straightforward. There is no question that you can plug both Macs into a normal network and they can share files if you turn on File Sharing.
The iMac has a Gigabit Ethernet port, and if the G4 also has Gigabit Ethernet, that will be a very fast connection through a gigabit-capable Ethernet cable or router. Otherwise both can use the slower Ethernet speeds with no problem.
You can also network the two machines via a FireWire 800 or FireWire 400 cable if necessary, and use File Sharing that way too. Finally, you can put one Mac into FireWire Target Disk Mode, which turns it into a hard disk that the other Mac can see, but this is the least flexible since one machine goes out of service, and it's probably no faster than Gigabit Ethernet.

What is the best way to connect macbook running sling adapter to the tv

what is the best way to connect macbook running slig adapter content to the tv

Since you posted in the Thunderbolt Display Community, I am guessing you are attempting to connect a MacBook Air to a Thunderbolt Display, but since you tagged projector, it makes me doubt my assumption. Can you provide some more details on what you are trying to connecto your MacBook Air to?

Hi I would like to show a presentation written on my macbook air on my television what is the best way to connect the two ?

Hi I would like to show a presentation written on my macbook air on my television what is the best way to connect the two ?

Much depends on the available connectivity of your television.
If it has HDMI input available, all you will need is a minidisplayport to HDMI adapter, and an HDMI cable long enough to place the Mac in the desired proximity to the TV. The adapter is avaialble from the Apple Store online.
Provided the HDMI input on the television supports sound, and the model of your MBA supports it as well, make suree that your adapter is also supportive of sound, otherwise you will need to run separate cabling from the headphone jack of the MBA to TV sound input or external speakers.
This is a somewhat specific answer to a question without any requisite detail. You don't indicate the model or type of inputs on your TV, nor do you indicate the model/generation of MBA you have.

What is the best way to connect time capsule to bt infinity

Similar Messages

Maybe you are looking for