What is the cause of the loss wireless between the WRT110 & WAG54GX2 ?!!!

The beginning, I like to thank you my brothers for your help me to solve a problems facing the wireless network, a few days before i put the subject of the problem of communication between the WRT110 & Linksys WRT160N on this link
http://forums.linksys.com/t5/forums/postpage/board-id/Wireless_Routers?comm_cc=US&comm_lang=en
I have Linksys WAG54GX2 as main router with the Internet service, & it's conneted with WRT110 device through the wire, so that the latter re-broadcast the Internet in rooms away from the main distributor
The problem is that every few seconds separated the wireless network distributor WRT110 cut off the Internet !!!
 what is the cause of this problem?!!
Another point that the Internet has become slow across the wireless network in both routers,, what is the reason of that?!!
am attached some pics. of the settings of the two routers
First the main router settings (WAG54GX2):-
http://img520.imageshack.us/img520/985/linksyswag54gx2pic1wb2.jpg
http://img442.imageshack.us/img442/395/linksyswag54gx2pic2dy5.jpg
http://img442.imageshack.us/img442/2549/linksyswag54gx2pic3ih4.jpg
http://img442.imageshack.us/img442/7159/linksyswag54gx2pic4bp3.jpg
WRT110 router settings:-
http://img248.imageshack.us/img248/4908/wrt110pic1tv3.jpg
http://img248.imageshack.us/img248/6950/wrt110pic2vc5.jpg
http://img248.imageshack.us/img248/5788/wrt110pic3fr1.jpg
http://img248.imageshack.us/img248/4682/wrt110pic4vd6.jpg
http://img248.imageshack.us/img248/3711/wrt110pic5sm4.jpg

Thank you for your help, my dear,
I have worked as your good advice, Now i have a strong network and the Internet has become a quick .
I would understand some things about our preparations:
* is should the channel be different in those routers, and what would happen if they were on the same channel ?
* My wireless networks are not protected now, its un safe .. What is the best encryption of the wireless network .. Do you use the WEP or WAP, including what is the difference ?
* What are the steps to be followed by encryption in both the routers the main WAG54GX2 & WRT110?
* Why we change Fragmentation in WRT110
Can you help me in this link
http://forums.linksys.com/linksys/board/message?board.id=Wireless_Routers&thread.id=116282
Thank u again my brother
Message Edited by Almowdmer on 11-29-2008 11:19 PM

Similar Messages

  • What are possible causes for frequent loss of wireless mouse connectivity other than the batteries ?

    What are possible causes for frequent loss of wireless mouse connectivity other than the batteries ?

    Wi-Fi or another interference source. Try turning off the Wi-Fi and see if the problems continue. If that solves the problem, see if you can set your Wi-Fi to run in the 5 GHz range.
    Keyboard/Mouse – Troubleshooting Wireless
    WIFI AND BLUETOOTH FINALLY SOLVED, NO REALLY - YOSEMITE 10.10
    Bluetooth Wireless Problems
    Bluetooth devices become unresponsive

  • After updating my 4S to iOS 5.1.1 last night, none of my data applications are working today, nor Siri, iMessage or anything of the like. I'm at a loss as to what might have caused it. Is anyone else having this issue/has anyone found a fix?

    After updating my 4S to iOS 5.1.1 last night, none of my data applications are working today, nor Siri, iMessage or anything of the like. I'm at a loss as to what might have caused it. Is anyone else having this issue/has anyone found a fix? Everything seems to work fine if I connect to wireless, but if I'm not connected to it then nothing is working. My service provider says everything should be working fine, I still have the 3G symbol and full bars.

    Somebody clearly hasn't read the User Guide.
    Basic troubleshooting steps are retart, reset, restore from backup, restore as NEW. 
    If you have tried ALL of these steps and you're still having problems, then you need to bring your phone into Apple for evaluation.

  • What's the best way to use Time Capsule through Extended Wireless Network?

    I am operating four computers, three Apples and a PC.  All the Apples use Snow Leopard.  I have a large house where the cable company's modem and internet access is located downstairs at the far back of the house.  That is where I have a 2Tb 802.11n Time Capsule (TC) connected to the modem by ethernet cable.  My iMac is there, connected to the TC by ethernet cable.  In the middle of the house, also downstairs, I have an Airport Extreme (802.11n) operating as a wireless bridge.  Upstairs in the front of the house (very far from the TC and closer but not very close to the AE) I have a home office.  That is where my other two Apples--a MacBook Pro and a MacBook Air--are usually located.  The PC is located in a bedroom directly above the TC and wirelessly connects to it.  At all locations, I get four radio signal strength bars.  However, I am not sure that the AE is doing anything, because I get four bars regardless of whether the AE is plugged in, or not.  When it is turned on, Airport Utility on all computers shows both the TC and the AE, but I have not been able to find which Airport ID I am actually connected to. 
    From my home office I do temporarily lose my internet connection from time to time each day, but the connection recovers usually within seconds.  I assume this reflects occasional interference or other loss of wireless signal in the distant home office, although I do not see the radio bars diminish to less than the four bars.
    All three Apples are set up to use the same TC for backup into Time Machine.  However, I have been getting errors on the laptops operating in the home office (a long way from the TC and perhaps connecting directly over wireless or perhaps wirelessly through the AE bridge.  Some messages are to the effect of being unable to backup, and others more recently report errors.  I think that either due to connection interruptions or merely by suspending or turning off the computer while in the middle of backing up, errors in the Time Machine files were created.  I have been unable to delete more than a few of the 8Mb sparsebundle bands so that I can completely get rid of one of the sparsebundles for the MacBook Pro.  I was able to get rid of the other sparsebundle for that computer and also the sparsebundle for the MacBook Air.  I am reluctant to erase the entire TC, because it has been working for the directly connected (by ethernet cable) iMac sitting right next to the TC.
    So, I am wondering what is the experience of others who are trying to use TC successfully from computers located a long distance from the TC with either a direct wireless connection or a bridged wireless connection through an AE or other bridge.
    And does anyone have good ideas about how to delete the sparsebundles effectively?  I read the various questions and answers in the support community, but so far nothing that I have tried based on those messages seems to work.  It seems that when all the Time Machines are set to "Off" and the sparsebundles are expanded to show the individual bands, we ought to be able to delete them fairly expeditiously.  Sometimes, I can delete one band fairly quickly, but then the second band will hang forever.  More often, I can't even delete the first band.

    Thank you, Bob.  I followed the procedure you stated.  My AE is working.  I did register its BSSID when I put my laptop next to it.  This is also the BBSID I am getting when in my home office at the far end of the house from the TC.  This means I am using the extended bridge AE when working and trying to use the automated backup feature in Time Machine.  Do you think I should turn off Time Machine on these laptops when they are in the home office, and bring them into the room with the TC occasionally to have a better connection (wireless to TC or by connecting an ethernet cable) when trying to make Time Machine backups for them?
    Interestingly (in contrast to the exact match of BBSID's for my AE), when I compared the BSSID for my TC in Airport Utility to the BBSID of the TC using the option key and the fan shaped Airport icon, the BBSID's matched except for the last two digits.  In Airport Utility, they are 2F.  In the fan shaped Airport icon they are 30. 
    Also, the AE signal, being centrally located on the first floor of the house, seems to be the one most in use.  When I walked my laptop away from the AE all the way back to the TC, the laptop automatically switched over to the TC only once.  Most of the time, the laptop is still connecting wirelessly with the AE.  To switch back to the TC, I have to turn Airport off, and then turn it back on again.
    I don't know how efficient or inefficient the Time Machine is when connecting to the TC indirectly through an AE bridge.

  • IPhone 4S using 3G in the background,causing huge battery loss. From last three days I'm finding my phone switched off in the morning when I wake up. Please Help

    iPhone 4S using 3G in the background,causing huge battery loss. From last three days I'm finding my phone switched off in the morning when I wake up. Please Help

    Maybe you hit the power button for 5 sec while you were asleap?
    And what do you want to say us with:
    Abhijeet Gupta wrote:
    iPhone 4S using 3G in the background,causing huge battery loss.

  • What is the best way to extend a Wireless network?

    Hi,
    We have 3 devices,
    1) Our Primary Network Router (which creates our office Network and has DHCP enabled).
    2) We have and Airport Extreme, which is used to create our Wireless Network (THIS IS SET TO “Create Wireless Network”), it has DHCP Enabled, its DHCP IP Scheme is set to 192.168.2.x, where the IP Scheme of our Primary Network is set to 192.168.181.x.
    3) We have an Airport Express that we are trying to use to EXTEND our Wireless Network.
    The most important thing we are trying to accomplish is to isolate the Wireless Network from our Primary Network, so Wireless Clients can access the Internet, but CAN’T SEE or ACCESS the Shared Network Volumes AVAILABLE ON THE PRIMARY NETWORK.
    At the moment, the Wireless Clients can access the Internet and receive an IP in the range of 192.168.2.x from the DHCP Server in the Airport Extreme. That part of it is working, but the Wireless Clients can unfortunately still SEE and ACCESS the Network Volumes available on the Primary Network. WHICH IS NOT WHAT WE WANT!!
    Question 1: How can we have the Airport Create a separate Network, so the Wireless Clients CAN’T SEE or ACCESS the Network Volumes from the Primary Network, but can still get access to the Internet through the Primary Network?
    Question 2: What is the best way to use the Airport Express to “EXTEND” the Airport Extreme’s Wireless Network? I have tried WDS “Main” for Extreme and WDS “Remote” for Express, but all that doesn’t allow you to use the Extreme to Create a Separate Network, it uses the DHCP Server built into the Primary Network’s Router. Also tried to set the Express to “EXTEND WIRELESS NETWORK”, which seems to work, but I am not sure why. Because I don’t have a cable from the Extreme to the Express, which is sounds like you have to when it is setup that way!!
    Any help would be greatly appreciated!!
    Thanks
    Kalagan

    Question 1: How can we have the Airport Create a separate Network, so the Wireless Clients CAN’T SEE or ACCESS the Network Volumes from the Primary Network, but can still get access to the Internet through the Primary Network?
    There is no way to do this. Any of the wireless clients of the AirPort Extreme base station (AEBS) can see any device connected to the AEBS's WAN port. Clients of a subnet can see anything on the supernet.
    You could configure you network like this:
    Internet-> (WAN) AEBS (LAN) -> Primary router
    As long as the Primary router was providing DHCP/NAT the things on the LAN side of the Primary router would be hidden from the AEBS clients.
    A better solution may be to have 2 completely separate networks OR invest in some type of network security firewall device to actively isolate your Primary network.
    Question 2: What is the best way to use the Airport Express to “EXTEND” the Airport Extreme’s Wireless Network? I have tried WDS “Main” for Extreme and WDS “Remote” for Express, but all that doesn’t allow you to use the Extreme to Create a Separate Network, it uses the DHCP Server built into the Primary Network’s Router. Also tried to set the Express to “EXTEND WIRELESS NETWORK”, which seems to work, but I am not sure why. Because I don’t have a cable from the Extreme to the Express, which is sounds like you have to when it is setup that way!!
    WDS is 802.11g's method of wirelessly extending a network.
    "Extend wireless network" is 802.11n's method of wirelessly extending a network.
    Neither of them require the AirPort Express (AX) to be cabled to the AEBS.

  • What is the Cisco tool for measuring traffic of wireless endpoint users

    Hi Experts
    I am looking to start a Mesh WISP utilizing Cisco Aironet products (1500 series) and would like to know what is the best Cisco (or if the case has to be "non Cisco") product for measuring the amount of traffic from wireless clients connected to my Cisco Mesh.
    Basically I want to be able to say User xyz has this IP xxx.xxx.xxx.xxx how much have they uploaded and how much have they downloaded this month.
    This also then allows me to integrate multiple business mobile devices into their broadband plans which is something no-one yet offers in my City.
    From what I have read Netflow is the measurement technology but how do I take this data and aggregate it by IP / User for billing purposes. Is there something better at it than Netflow? Your expert opinions and suggestions are much appreciated.
    Regards
    Ty

    That sounds like Cisco Wireless Control System (WCS).
    Cisco Wireless Control System (WCS) Data Sheet
    http://www.cisco.com/en/US/prod/collateral/wireless/ps5755/ps6301/ps6305/product_data_sheet0900aecd802570d0.html
    Please don't forget to rate useful posts.  Thanks.

  • What is the number for Verizon Wireless  Corporate Customer Service Complaint for CA

    My Complaint:  I have been a Verizon Wireless customer for approx 20 years.  I called customer service to seek an early upgrade for my daughter's phone. She is away in college and her phone is malfunctioning.  She is eligible for an upgrade in approx 6 weeks so I did not want to spend the money on a replacement phone when since we were planning on updating to something newer.  The customer service rep to me they could not do the early upgrade an to call back in a few weeks. After explaining this was unacceptable (I do not like the idea of a young female being out of state and away from home with no reliable means of communication), she places me on hold to later return with the only offer of  I must purchase a new device through her ( over the phone) which will be shipped to me, the phone was priced $100.00 more than the online price (they will not price match), plus i must pay $30.00 upgrade fee, $35.00 activation fee and taxes on the retail price of the phone.  I am upset and disappointed with the quality of service provided by Verizon being a 20 year customer.  If not for the seriousness and urgency of this matter, i would not have asked for an early upgrade.  It is times such as these that you get to see how much of a "valued customer" you really are.   I guess you are valued as long as you pay your bill and continually  purchase their products.  I would like to speak with someone from Verizon's corporate or customer relations department.  As of now I am really considering changing my service to a different provider.  I have multiple accounts with Verizon and i will canx each after the current contract committment expire (starting with my daughter's phone which expires in 6 weeks) In the meantime I will go purchase her a new phone with someone else and take comfort knowing she will have reliable communication.

    I started with them in 1985. It has been wonderful service but very expensive. They seem to operate on day of deposit day of withdrawal. That means that I have no benefits nothing beyond the normal customer if I don't pay my bill they shut me off. That's why I have switch to another provider and I have better service lower cost and better phones. you can't beat  other providers I mean it. Please don't expect more from verizon other than a "pay me more money and I'll do what you want" because it's all about money. Read the transcripts from current Verizon employees all over the internet. The company is going down and they're taking customers with them.
    msvat <[email protected]> wrote:
    msvat  created the discussion
    "What is the number for Verizon Wireless  Corporate Customer Service Complaint for CA"
    To view the discussion, visit: https://community.verizonwireless.com/message/1113982#1113982
    >

  • I have a pioneer vsx-910-k and airport express.I have a wireless network at home. What's the best arquiecture/config to do with this hardware?

    I have a pioneer vsx-910-k and airport express.I have a wireless network at home. What's the best arquiecture/config to do with this hardware?

    I would suggest that you connect the Pioneer to the AirPort Express Base Station using an optical digital audio cable that has a TOSlink connector on one end and a 3.5 mm optical connector (Mini Plug) on the other. You can then connect the Mini Plug end into the AirPort's audio port and the TOSlink end into one of the Pioneer's optical digital audio ports.

  • I am using itunes 10 and trying to consolidate my files.  I keep getting the error "Copying files failed.  The file name was invalid or too long".  How can I indentify what file is causing this problem or resolve this issue?

    I am using itunes 10 and trying to consolidate my files.  I keep getting the error "Copying files failed.  The file name was invalid or too long".  How can I indentify what file is causing this problem or resolve this issue?

    BUMP
    Yes, I just get that message. I don't see how I could investigate this problem.
    I didn't mention that this happened when I was consolidating my library, not copying files to another computer.
    In other words, I'm using a "normal" itunes procedure, itunes won't complete it, and won't tell me exactly why or how to figure out how to fix it...
    Is there at least some easy way to tell which files were successfully copied to my itunes music folder so I can work on moving the uncopied files?
    Can anybody help me?

  • What's the proper protocol for a reset on my ipod touch 4g?  iOS 6 has totally jacked it up and it will no longer do anything but crash, and won't sync with itunes wirelessly or by cable.

    What's the proper protocol for a reset on my ipod touch 4g?  iOS 6 has totally jacked it up and it will no longer do anything but crash, and won't sync with itunes wirelessly or by cable.
    It's a 64G ipod touch and was fine till Apple told me to upgrade to ios 6.  Now most of my apps crash, my music won't play and I just get a white screen when I hit Music.
    When I try to sync to itunes it acts like it's going to sync and appears to recognize the ipod, but it's grayed out and has an update circle by it that spins for a while until itunes eventually freezes alltogether.  Is there a  way to go back to ios 5 after a erase and reset?

    iOS: Unable to update or restore

  • My ipod 3rd gen. touch screen is unresponsive, cant slide to unlock or enter passcode to access ipod. What is the cause? how do i fix this?

    my ipod 3rd gen. touch screen is unresponsive, cant slide to unlock or enter passcode to access ipod. What is the cause? how do i fix this?

    Try:                                               
    - iOS: Not responding or does not turn on           
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try another cable       
    - Try on another computer                                                       
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar                                     

  • THE LINKS AT THE TOP OF ANY WEB PAGE NO LONGER WORK. wHAT COULD BE CAUSING THIS

    WITHIN THE LAST FEW DAYS NO MATTER WHAT WEBSITE I GO TO THE LINKS IN THE BANNER OR TOP PORTION OF THE PAGE DO NOT WORK. THE SYSTEM DOESN'T SEEM TO KNOW THAT THEY ARE LINKS WHEN I HOVER OVER THEM I GET THE MOUSE ARROW ICON INSTEAD OF THE HAND LIKE I DO ON ALL OTHER LINKS ON THE PAGE. THE LINKS ON THE SIDES AND BOTTOM OF THE PAGE WORK JUST FINE. WHAT COULD BE CAUSING THIS?

    That is a problem with the Yahoo! Toolbar.
    *https://support.mozilla.com/kb/Troubleshooting+extensions+and+themes
    Start Firefox in <u>[[Safe Mode]]</u> to check if one of the extensions or if hardware acceleration is causing the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > Appearance/Themes).
    *Don't make any changes on the Safe mode start window.
    *https://support.mozilla.com/kb/Safe+Mode

  • What is the diff of Solution monitoring and E2E Root cause analysis

    Hi,
    I want to know what is the different for Solution Manager Solution Monitoring and End to End root cause analysis. Currently we have implemented change management and Implementing and Upgrading SAP Solutions, if i would like to explore the solution monitoring, and end to end root cause analysis, what is the steps of configuration i need?
    if i would like to have a check on the system whether is performing well, or setup the functionality of sending alert when system is having problem, which feature would be better? end of end functionality or Solution Monitoring?
    Please advice..
    thanks
    -Fung

    Hi,
    If you have PI system in your landscape, I would strongly recommend to upgrade to SP15.
    Trace monitoring for PI is to be available from SP17 (Not yet released)
    Check [this Link.|http://service.sap.com/e2e].
    Hope this solves your problem.
    Feel free to revert back.
    --Ragu

  • What is the best way to link 4 Airport units together wirelessly?

    Hi guys,
    I have a home with tick walls and creating  a decent wireless network was always a challenge. Recently I’ve decided to go for Apple products since I had a 4th gen airport express that worked well for airplay.
    I bought a new time capsule, airport extreme, and one airport express. So in total I have 4 apple devices that I can use for creating a good wireless network. But what I found out is that having a full signal doesn’t mean that you will have good speeds, and speeds are really slow like 3Mb/s max on some places on the house.
    The way that everything is configured at the moment is that I’ve configured the time capsule to be the main router and with the other three I’ve spreaded them over my house and selected the option to extend a wireless network using Airport Utility 6.2 on OSX.
    What is strange that I have a full signal on almost all corners but very bad speeds. I did some research and found a tool that would show what the less crowded channel that you can choose for you wireless network (http://tools.meraki.com/stumbler)
    In all my experience of extending a wireless network I’ve always used routers with DD-WRT so I could select the router to be a repeater bridge (and have two distinct networks, with different names) or link the routers with WDS linking them using the MAC address. In both cases all the documentation I’ve read recommended to set all routers of the same network with the same channel.
    When I used the stumbler tool to see what channel my network was, since it was set as automatic because it’s the recommendation of Apple documentation, I found out that all 4 routers were operating on different channel on both 2.4Ghz frequencies and 5Ghz frequencies.
    What is strange with the wireless network is that sometimes when it is really slow the speed of the internet, if I disconnect from the wireless network and connect again it gets a better connection, like I was connection to a closer router. But after sometime speeds get crappy again, like it changed to the far router again.
    My question is, what is the best way to link all this routers together wirelessly? Is there a way to make them to be all on the same channel? Is that important?
    On the Airport Utility 6.2 I don’t see any field that would make possible to link this routers using WDS. On the internet I found some documentation for configuring the routers with WDS with the Airport Utility 5.6.
    All my routers are updated to the latest version (7.6.3). Please let me know how to proceed to have a decent network on my house. I wouldn’t mind having the network set with different SSIDs but it would be better to use the same network name on all the house.
    Thanks in advance,
    Tiago

    At the moment it is configured like this.
    [IMG]http://img254.imageshack.us/img254/6403/capturadetela20130210s2.png[/IMG]
    My problem is that the signal its strong but speed isn’t. On Wifi stumbler I saw that every router is set to be on a different channel, they had to be the same no?
    If its really slow if I disconnect and connect again from the network. It gets faster, like it connected to a closer router or something.
    All are set to extend a wireless network.
    Regards,
    T

Maybe you are looking for