What is the Cisco 881G "PDP establish max timeout" ?

Hi
What is the Cisco 881G "PDP establish max timeout"?
The Cisco 881G 3G connection is to be disconnect by PDP establish max timeout. I want to infinite to establish this connection. What parameter I can adjust?

Hi Jonson,
PDP Context Idle Timeout
When a data session is established it uses resources in the network, if there is no data passing over this session then many operators close the session automatically after a set period of time. This can be as short as after 10 mins and as long as after 24 hours. Each time the data session is closed any rounding and minimum session size criteria will be applied.
try the below command.
you also might need to update the firmeware on the router to get the dialer persistant command
router(config-if)#dialer idle-timeout 0
cheer
phil

Similar Messages

  • What is the cisco ironport C680 and M680 configuration backup file size?

    what is the cisco ironport C680 and M680 configuration backup file size?

    Size of the XML itself?  That is going to vary based on what you have configured, total lines of code, and # of appliances you may/may not have in cluster.
    M680, based on SMA as stand-alone, should be similar --- you are probably looking @ < 1 MB... 
    Looking @ my test environment, in which I have a nightly cron job set to grab a backup of...
    -rw-rw----  1 robert robert 161115 Sep 26 02:00 C000V-564D1A718795ACFEXXXX-YYYYBAD60A5A-20140926T020002.xml
    So, 161115 bytes = .15 MB
    -Robert

  • What is the Cisco tool for measuring traffic of wireless endpoint users

    Hi Experts
    I am looking to start a Mesh WISP utilizing Cisco Aironet products (1500 series) and would like to know what is the best Cisco (or if the case has to be "non Cisco") product for measuring the amount of traffic from wireless clients connected to my Cisco Mesh.
    Basically I want to be able to say User xyz has this IP xxx.xxx.xxx.xxx how much have they uploaded and how much have they downloaded this month.
    This also then allows me to integrate multiple business mobile devices into their broadband plans which is something no-one yet offers in my City.
    From what I have read Netflow is the measurement technology but how do I take this data and aggregate it by IP / User for billing purposes. Is there something better at it than Netflow? Your expert opinions and suggestions are much appreciated.
    Regards
    Ty

    That sounds like Cisco Wireless Control System (WCS).
    Cisco Wireless Control System (WCS) Data Sheet
    http://www.cisco.com/en/US/prod/collateral/wireless/ps5755/ps6301/ps6305/product_data_sheet0900aecd802570d0.html
    Please don't forget to rate useful posts.  Thanks.

  • What are the Cisco 1300 series Antenna Alignment options?

    I am wondering if there are any options for aligning the antennas other than RSSI LED indications.  The cisco aironet is going to be on top of a 10m tower and the lights will not be visible. Is there any way to configure them to an audible output that would increase in loudness or pitch when the signal was strongest?

    Check this:-
    "Best Practices" for positioning Access Points (AP's) and Antennas
    https://supportforums.cisco.com/docs/DOC-16627
    thanks,
    Vinay

  • What is the best way to establish sso between iphone and IIS?

    Hi experts,
    I try to configure the SCEP, and I can view a IIS content with "Certificate required", but, can I validate the username with this certificate?
    thanks in advance,

    Hi,
    Yes, TCP/IP is most universal way for the communication. Otherwise you should develop some parts for establish connection / break connection / wait for the data. This way also good when you need to transfer the data across network.
    Another possible way is following: you can create DLL from your LabVIEW code, then call this dll from your C# application, and interchange the data through this DLL. Here you can use different techniquies (also TCP/IP as well). The advantage of this method that you will establish LabVIEW<->LabVIEW communication.
    In attached example I have create "quick and dirty" project with shared variables. LabVIEW application will write the shared variable, then external application will read this, increment variable, then LabVIEW will read it back. I have used CVI, but you can call SharedLib from C#, here no differences.
    Something like that:
    best regards,
    Andrey.
    Message Edited by Andrey Dmitriev on 10-28-2008 03:17 PM
    Attachments:
    App Intercomm Test.zip ‏224 KB
    ScreenshotSV.png ‏13 KB

  • What is the file name that stores MAX channel information?

    I have recently lost all my cannel information within NI-MAX. In order to prevent this in the future, Can anyone tell the name of the file that stores all the channel information created using NI-MAX?
    Dan

    Hi Dan,
    The configuration settings in MAX can be found in the following directory:
    C:\Program Files\National Instruments\MAX\Data
    Refer to this KB which explains how to save your MAX system configuration.
    Please repost if you have further questions.
    JenK

  • What is the Cisco ASA 5520's VPN ustility like?

    Hi, I have a Cisco 3015 VPN concentrator, the Web admin tool is really good. We are getting a 2 Cisco 5520 soon in failover mode and I wondered if I should move my site-to-sites to the ASA 5520 and if so how good it the tool for the ASA VPN's as I not seen it yet?

    The VPN capabilities of the ASA are very similar to that of the concentrators. Much of the management interface will have the same look and feel on both appliances. Migrating your L2L VPNs is a matter of preference and will depend on your topology. For me, I prefer to terminate my L2L VPNs into a DMZ and use the ASA to permit/deny traffic into my LAN.

  • What is the best type of xml storage for max performance in 9i r2

    We have many schema based xml's of 1MB in xdb (9.2.0.5)
    and our database is getting slower by every new xml
    delete_resource (300 sec) and create_resource (300 sec ) take a long time
    and if I ftp a schema based xml out the xdb takes a long time ( 200 sec )
    Our system works like this , the xml comes in (ftp) ,the xdb validates the xml and then the xml is archived and the
    last step, the xml data is extracted and put in normal tables
    no xml updates or xml constraints
    I have now defined in the schema, one main table and I use oracle types for complextypes and xdb:defaulttable =""
    in 10g I don't have problems, but our production system
    are 9.2.0.5 and it takes a lot work and downtime to change that
    This goes well in 9i by files smaller then 500k
    what is the best schema configuration for max performance ( create / delete resource and ftp out )
    thanx edwin

    I changed
    maxOccurs="unbounded" xdb:SQLName="TRANSACTIONRANGE" xdb:SQLCollType="TPF_MASTER_D_T_RANGE_COLL_01"
    into
    maxOccurs="unbounded" xdb:SQLName="TRANSACTIONRANGE" xdb:SQLInline="false" xdb:defaultTable="TPF_MASTER_D_T_RANGE_TAB"
    this gives me very good performance
    the total run is now 6 times faster
    and to ftp xml out of the xdb takes now 2 seconds

  • HP Pavilion DV2700 Special Edition what is the max ram for this model laptop?

    HP Pavilion DV2700 VERVE Special Edition
    Operating System  Windows Vista 64 bit Service Pack 2
    Year made 2007 
    Processor AMD Turion 64 X2 TL- 60 2.0 GHz
    Current Ram 4GB
    would like to know what is the max ram 
    PS 
    Can i install and other Processor or is this and intergrated one with the motherboard.? 
    In Advance thank you for your time to look at my question
    Indarktimes
    This question was solved.
    View Solution.

    Hi
    Please find the link given below for your model off unit Max Memory supported is 4GB.
    http://h10010.www1.hp.com/wwpc/ca/en/ho/WF06a/12139188-78299199-78299212-78299212-78299212-81135202....
    Let us know how it goes!
    "I work for HP."
    ****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    Regards
    Manjunath

  • What is the max. count of internal worker-threads in B1iSN 88?

    Hi Experts,
    We have an installation of B1iSN 88 with an ECC 6.0 and 54 SAP Business One installation. The Hardware is 8 Core multi-threads processor. 32GB Memory. Now we have a problem with the queuing of Events. What we have found is that the configuration of the internal worker-threads is set to -1(please see below for the settings). We change the settings to xcl.threads=20 and it improves the queuing. My question is what is the max. count of internal worker-threads per core? so that we can know how many worker will set and if we need to upgrade the CPU to 16 Core..
    # The max. count of internal worker-threads afforded for the internal Scheduler (defaults to 1)
    # The value of 0 means that there is no limit (what in general should not be set up).
    # A negative value means the count of threads per available processor
    xcl.threads=-1
    Regards,
    Wilson

    You're very welcome.
    Yes, they are very nice machines. 
    What a jump in performance when I swapped out the Pentium 4 620 mine had, for the PD 945, and tossed in 4 GB of memory.
    That box will also run the Radeon HD 6570 with no problem too, which is what I put in mine.
    The downside of that model is that there are no settings for ahci or raid.
    I own or have owned every CMT since the d510 with the exception of the dc7900.
    My main PC is now the 8200 Elite CMT which I installed W8.1 on.
    It has an i7-2600 processor and 32 GB of memory, 1 TB SATA III hard drive.
    I threw in a Radeon HD 6670 in that one.
    Best Regards,
    Paul

  • What is the max size of HDD I can use in my dc7600 CMT

    I am using an HP dc7600 CMT which is working fine after upgrading to a Samsung 128GB SSD, Intel Pentium D 3.4 GHz, 4GB RAM, and an AMD Radeon HD 6450. I am running Win 8.1 Pro x64, with the most recent upgrade, and have absolutely no problems. I now want to add a second internal HDD, and wonder what is the max size  I can go to. Can I go to 2TB, or am I limited to a lower figure? 1TB? 500GB? 250GB?
    Will be glad for some help here, especially if it has been actually tried in practice.
    Thanks in advance.
    Best regards
    This question was solved.
    View Solution.

    You're very welcome.
    Yes, they are very nice machines. 
    What a jump in performance when I swapped out the Pentium 4 620 mine had, for the PD 945, and tossed in 4 GB of memory.
    That box will also run the Radeon HD 6570 with no problem too, which is what I put in mine.
    The downside of that model is that there are no settings for ahci or raid.
    I own or have owned every CMT since the d510 with the exception of the dc7900.
    My main PC is now the 8200 Elite CMT which I installed W8.1 on.
    It has an i7-2600 processor and 32 GB of memory, 1 TB SATA III hard drive.
    I threw in a Radeon HD 6670 in that one.
    Best Regards,
    Paul

  • We are a creative design studio, we need to use apple mac pro server , so we can make more than a different user to use at the same time doing different activities, on different screens, is it possible?what is the max. no. of users that can work efficient

    we are a creative design studio, we need to use apple mac pro server , so we can make more than a different user to use at the same time doing different activities, on different screens, is it possible?what is the max. no. of users that can work efficient.
    Appreciate your support and if possible , how to do this?

    If you want to work with Mac OS X, you need one computer per simultaneous user.
    What you are describing, " Multiple simultaneous logins to a single computer" is not avialable on a regular Mac of any description, unless you decide to use Unix tools instead of Mac OS X.
    Server will happily store files for many, many users and provide them to multiple (up to hundreds) of computers at "near hard Drive" speeds over Gigabit Ethernet. It can make the File Sharing part easy.

  • What are the features supported in Cisco Prime Infrastructure for WLAN for autonomous AP's?

    What are the features supported in Cisco Prime Infrastructure for WLAN for autonomous AP’s?

    • PI provides visibility for autonomous  clients within the same list view as lightweight and wired clients (client list  page).
    • Rogue AP detection for autonomous AP's is not supported (it's  supported in CUWN). 
    • Alarms/events for client authentication issues (e.g.  authentication failure) are displayed in PI.
    • Config management for  autonomous AP's is via CLI template.  Config comparison and archiving  functionality in PI leverages these same features that were brought in from LMS,  so need to defer to others in terms of whether this is a cross-platform feature  in PI or is only supported on a subset of platforms.  Config comparison/archive  is supported in CUWN.PI supports both infrastructure (e.g. AP Tx Power and  Channel, busiest AP, AP utilization, etc.) and client (e.g. client count, client  sessions, etc.) reports, and there are extensive reports for CUWN

  • I have MacBook Pro 2.2GHz Intel Core i7 (15-inch DDR3) Early-2011 and I want to upgrade RAM, What is the MAX RAM can I get it 8GB or 16GB?

    I have MacBook Pro 2.2GHz Intel Core i7 (15-inch DDR3) Early-2011 and I want to upgrade RAM, What is the MAX RAM can I get it 8GB or 16GB?

    Maximum Memory     16 GB (Actual) 8 GB (Apple)
    Memory Slots     2 - 204-pin PC-10600 (1333 MHz) DDR3 SO-DIMM

  • What are the ideal settings for my TC with Shaw's Cisco DPC3825 router/modem

    My old 2nd Gen Time Capsule crapped out and now I am about to set up my new 2TB TC.  My provider is Shaw Communications and they have upgraded me to their Broadband 100 Mbps service.  This came with a new modem/router combo made by Cisco and is model DPC3825.  Before I start plugging things in I'd like to know what are the ideal settings such that I gain the most of the BB100 service.  Should I be setting the Cisco modem/router to Bridge mode or the TC?  Should I have Shaw disable anything?  Any insight is greatly appreciated.

    Unless you specifically need to have the TC perform as the main router for your network, life will be a lot easier if you configure the TC to operate in Bridge Mode.
    Whether the Cisco modem/router or gateway can possibly be configured to act as a simple bridge mode modem is one thing to consider.
    Whether Shaw would support you in the event of any connection difficulties with the modem/router configured this way is another.
    Since Shaw is your provider, it might make sense to talk with them about best practice as far as configuring the DPC3825.
    Once you have that information in hand, you will then have the answer on how best to configure the TC.....which will very likely be in Bridge Mode.

Maybe you are looking for