What is the correct method to configure PC3500 memories?

I am working with Neo2-LS.
Where exactly in the BIOS setting, I need to set the correct speed?
At the moment, it's working with 400MHz. instead of 433 MHz. as it should.
Thanks.

PC3500 or 433MHz only tells you that the RAM has been validated to run at that speed without problem. But now you're putting on a Springdale chipset system, of course it's running at 400MHz, the top speed supported by SpringDale chipset, unless you want to go further by overclocking the FSB which will indeed increase the RAM speed too.

Similar Messages

Implmenting Reminders for a Notification - What is the correct method?

Hi,
I am trying to implement sending out reminders to a person who has a notification open.
A Manager(UserA) gets assigned a notification(NoteA) to approve/reject. After 7 days, he should get a reminder saying that NoteA is waiting for his decision. The way I implemented this is that after 7 days, the NoteA times out and sends out a new notification(NoteB).
However, the problem is that within 7 days, the UserA might have reassigned this NoteA to another Manager(UserB) for evaluation. So, when it times out, NoteB gets assigned back to UserA. Needless to say, UserA is now unhappy!
There was an example in the FAQ about implmenting reminders, but I beleive even if I implment the method suggested in the FAQ, I will end up with the same problem described above, since the reminder notifications will still go to UserA.
Would appreciate any help on the corrrect method to implment reminders. FYI- I am using standalone workflow.
Thanks
Dev

Dev, you could always write a post notification function which detected the REASSIGN and assigned the new performer to an item attribute, which would then be used as the performer for the reminder notification.

VMI: reduce Stock in transit - what is the correct method?

Hi Gurus,
We are using APO/SCM system to implement VMI functionality to replenish stock at customer location. We need to build stock in transit at customer location after PGI happens in ECC.
Now, stock in transit is show up in 'Stock in transit' key figure, but the question is how to reduce stock in transit once it is received at customer location.
SAP recommends following four methods to reduce:
http://help.sap.com/saphelp_scm2007/helpdata/en/f1/f69a3dcbcfac53e10000000a114084/frameset.htm
1. Goods receipt information is not sent from the customer to the vendor
2. The open purchase order quantity is sent from the customer to the vendor
3. A proof of delivery is sent from the customer
4. The stock in transit quantity is sent from the customer to the vendor
Out of these 1 and 2 methods are feasible in our scenario.
Please share your experience if you have used any of these methods, I want to hear from someone who implemented any of these methods before deciding on a method.
Thanks in advance,
Niranjan

After research and testing I found second method looks good to me. I tested in our test system, this works pretty much they way it is described in the help (link in above message) . The issue is resolved.

What is the correct method of removing a green screen background to insert a new digital background?

I am using Photoshop Elements 10 and can't seem to remove the green screen correctly. When I select the "magic wand" and click on the green screen background it selects it as it should. But when I hit the delete button on my keyboard it deletes the green background but a white background remains. So when I go to select my image to drag it to my digital background the white background goes with it.
In the tutorial video I watched it shows a grey and white checkered background after deleting the green screen which allows the user to select and move only the image to the new digital background. I am following the steps exactly but still can't seem to get it to work. Any ideas?

I don't know about 10 but in In PSE 8 there is a "Magic Extractor" ( ALT+SHIFT+CTRL+V) (on the mainu it's under Image ) which makes waaay too easy to seperate a selection from the background
http://help.adobe.com/en_US/PhotoshopElements/8.0/Win/Using/WS083AC514-D907-483b-84A1-4EA3 989C4C65_WIN.html
As already mentioned, the trick with the "background layer" is to right click on it in Layers and use "Layer from background"This will turn it into a "regular layer".
Then add a another new layer and on this new layer paste your cut-out you created earlier using the magic extractor.
D

Please recommend the correct method to configure GL Acct Item Map

Regarding GL Account determination for item master.
I want to track in my COA by different GL Accts, revenue for the same item but based on where it was sold.
We sell the same ITEM in our ecommerce site, in our bookstore, and in remote locations.
Either I create the SAME item multiple times and map them to coresponding GL Revenue accounts or ....
is there a different way to do this please.
I was thinking of perhaps using account determination per warehouse but I don't think it would work.
Thanks,

Suda:
Let me rephrase the question.
The business objective is to track sales from different channels: Ecommerce, Bookstore A, Bookstore B, Direct Sale, etc (Effectively we can think of them like different store fronts or locations).
However the same customer could buy from all different channels.
Customers are classifed per group like MEMBER, NON MEMBER, DISTRIBUTOR
Yet the business objective is to understand:
1. Revenue per channel
2. Revenue by item group
3. Revenue per channel, per item group
4. Revenue per item group, per channel
4. Revenue per customer group
I have started to use PROJECTS but I find them after having a lot of projects, it gets cumbersome.
Thanks for your help.

Zenphoto setup - what is the correct method for proper permissions?

http://www.zenphoto.org/
Permissions are "drwxr-xr-x 3 root root" for all directories mentioned
apache DocumentRoot is default of "/srv/http"
Zenphoto is extracted under http in a folder named "photos". When I initialize the Zenphoto setup in my web browser, I receive numerous errors that the setup php does not have write permissions within the "photos" directory.
The setup recommends setting 777 to all folders within and including the "photos" directory (zenphoto base).
I really don't want to set 777 permissions... Zenphoto setup doesn't complain if I set permissions to 775. But I am wondering if there would be less issues if I just set the "photos" directory recursively to the owner of "http"
Which would be best/proper?
Thanks!

I notice that if I do a repair permissions 2 or 3 times in a row that some of the same permissions are repaired again and again.
I assume you are referring to the log entries which contain "We are using special permissions..."
If so, you can safely ignore those messages. They are purely informational. This is not indicative of a permissions problem.
There is also no need to repair permissions while booted from the system DVD. Running it the way you are is fine, and you should only need to do it when you have a problem with your machine resulting from improperly set permissions.

What is the correct method of transfering music fi...

kindly instruct how to transfer music tracks from the pc to the phone n73? is it better way to transfer through mass storage or using nokia pcsuite-drag and drop to phone icon?

It depends as its posted above. You could also BT the files or use OVI files to put the files on the cloud and access them from your phone.
You can put the memory card in a card reader and load the songs that way.
640K Should be enough for everybody
El_Loco Nokia Video Blog

What are the correct answers ?

after doing one sample swing application, i assumed the exam will be easy. when i took the exam, i couldn't do anything...
what are the correct answers ??/
Which one of the following converts the Image i into the BufferedImage bi?
Choice 1
bi = new BufferedImage(0, 0, BufferedImage.TYPE_INT_RGB);
Graphics2D g = (Graphics2D)bi.createGraphics();
g.drawImage(i,i.getHeight(this),i.getWidth(this));
Choice 2
bi = new BufferedImage(i.getWidth(this), i.getHeight(this), 1);
bi.drawImage(i,0,0,this);
Choice 3
bi = new BufferedImage(i.getWidth(this), i.getHeight(this), 1);
Graphics2D g = (Graphics2D)bi.createGraphics();
g.drawImage(i,0,0,this);
Choice 4
bi = new BufferedImage(i, i.getWidth(this), i.getHeight(this), BufferedImage.TYPE_INT_RGB);
Choice 5
bi = new BufferedImage(i, i.getWidth(this), i.getHeight(this));
CardLayout
BorderLayout
FlowLayout
GridBagLayout
GridLayout
Which one of the following indicates all of the layout managers (from the list above) that allow you to set the space between the components from an instance of the LayoutManager itself?
Choice 1
CardLayout, FlowLayout, GridBagLayout, GridLayout
Choice 2
GridBagLayout
Choice 3
BorderLayout, GridLayout
Choice 4
BorderLayout, FlowLayout, GridLayout
Choice 5
BorderLayout, CardLayout, FlowLayout, GridBagLayout, GridLayout
JFrame jf = new JFrame();
jf.setSize(400,400);
JTextField jtf = new JTextField("JTextField");
JButton jb = new JButton("JButton");
jf.getContentPane().setLayout(
                      new FlowLayout(FlowLayout.LEFT,1,2));
jf.getContentPane().add(jtf);
jf.getContentPane().add(jb);
Which one of the following indicates the positions of the JTextField jtf and JButton jb relative to the JFrame and each other?
Choice 1
jtf and jb are in the top-center of the Jframe; jtf is to the left of jb, 2 pixels apart.
Choice 2
jb is in the top-right corner of the JFrame with jtf 1 pixel to the left of it.
Choice 3
jtf is in the top-left corner of the JFrame with jb 1 pixel to the right of it.
Choice 4
jb is in the top-right corner of the JFrame with jtf 2 pixels to the left of it.
Choice 5
jtf is in the top-left corner of the JFrame with jb 2 pixels to the right of it
public void drawText(Graphics2D g, String text){
Font f = new Font("Century Gothic", Font.BOLD, 10);
g.setFont(f);
g.drawString(text, 20, 20);
Given the above sample code, what happens if the "Century Gothic" font is NOT available?
Choice 1
The Font() constructor fails, causing "f" to be null, and the setFont() method throws a NullPointerException.
Choice 2
"Century Gothic" is a built in Java font, which always exists within the Java runtime environment.
Choice 3
The code does not compile because only the following "logical" font names are supported in Java: Dialog, DialogInput, Monospaced, Serif, SansSerif, and Symbol.
Choice 4
The Font() constructor throws an IllegalArgumentException.
Choice 5
A default Font object is returned and is used
Sample Code
public void drawText(Graphics2D g, String text){
Font f = new Font("Century Gothic", Font.BOLD, 10);
g.setFont(f);
g.drawString(text, 20, 20);
Given the above sample code, what happens if the "Century Gothic" font is NOT available?
Choice 1
The Font() constructor fails, causing "f" to be null, and the setFont() method throws a NullPointerException.
Choice 2
"Century Gothic" is a built in Java font, which always exists within the Java runtime environment.
Choice 3
The code does not compile because only the following "logical" font names are supported in Java: Dialog, DialogInput, Monospaced, Serif, SansSerif, and Symbol.
Choice 4
The Font() constructor throws an IllegalArgumentException.
Choice 5
A default Font object is returned and is used.
How must do you interact with a JTextField in order to generate an ActionEvent?
Choice 1
Tab into the JTextField from another Component.
Choice 2
Type in the JTextField.
Choice 3
Activate the cursor in the JTextField.
Choice 4
Hit <RETURN> while the cursor is in the JTextField.
Choice 5
Hit the spacebar while typing in the JTextField.
double-buffering
public class TimerTest implements ActionListener{
public static void main(String[] args){
    TimerTest test = new TimerTest();
    javax.swing.Timer timer = new javax.swing.Timer(100,test);
public void actionPerformed(ActionEvent ev){
    System.out.println("Timer ticked.");
Given the above sample code, what is the result when the code is run?
Choice 1
The words "Timer ticked." are printed to the console once after 100 milliseconds.
Choice 2
The words "Timer ticked." are printed to the console every 100 microseconds.
Choice 3
The words "Timer ticked." are printed to the console every 100 seconds.
Choice 4
The words "Timer ticked." are printed to the console every 100 milliseconds.
Choice 5
Nothing, the Timer is not started.
1. JSlider slider1 = new JSlider (JSlider.VERTICAL, 0, 100, 50);
2. slider1.setPaintTicks(false);
3. slider1.setMajorTickSpacing(10);
4. slider1.setMinorTickSpacing(2);
What changes do you have to make to the above Sample code so that there are six Major Ticks and four Minor ticks between each Major Tick?
Choice 1
Replace line 3 with slider1.setMajorTickSpacing(17);
Choice 2
Replace line 2 with slider1.setPaintTicks(true);
Replace line 3 with slider1.setMajorTickSpacing(17);
Replace line 4 with slider1.setMinorTickSpacing(5);
Choice 3
Replace line 3 with slider1.setMajorTickSpacing(5);
Replace line 4 with slider1.setMinorTickSpacing(4);
Choice 4
Replace line 2 with slider1.setPaintTicks(true);
Replace line 3 with slider1.setMajorTickSpacing(20);
Replace line 4 with slider1.setMinorTickSpacing(4);
Choice 5
Replace line 4 with slider1.setMinorTickSpacing(6);
   Which one of the following defines a set of three JRadioButtons (b1, b2, and b3) so that only one JRadioButton can be selected at a time?
Choice 1
ButtonGroup g = new ButtonGroup();
g.add(b1); g.add(b2); g.add(b3);
Choice 2
b1.group(true); b2.group(true); b3.group(true);
Choice 3
JRadioButton jbs[] = {b1, b2, b3};
ButtonGroup g = new ButtonGroup(jbs);
Choice 4
The default behavior of JRadioButtons is such that only one can be selected at a time as long as they are in the same Container.
Choice 5
ButtonGroup g = new ButtonGroup(b1, b2, b3);
Sample Code
public static void main(String args[]){
What is the role of the method in the code above?
Choice 1
To provide a place for initialization code when instantiating the current class.
Choice 2
It is the first method run when a class is run with the Java Interpreter.
Choice 3
It serves no specific function. It is a residual method from Java 1.0.
Choice 4
It is the first method that the Java Compiler converts to bytecode when creating a .class file.
Choice 5
To process command-line parameters when running the Java Interpreter
How do you create a menu item, Save, with a shortcut key of Ctrl+S?
Choice 1
You have to override the KeyPressed event of the top level Frame and handle the Ctrl+S to call the menu item's actionPerformed.
Choice 2
JMenuItem save = new JMenuItem("Save");
save.setAccelerator(KeyStroke.getKeyStroke(KeyEvent.VK_S,Event.CTRL_MASK));
Choice 3
JMenuItem save = new JMenuItem("Save");
save.enableShortcut(KeyEvent.CTRL_KEY + KeyEvent.S);
Choice 4
JMenuItem save = new JMenuItem("Save");
save.setMnemonic("Ctrl+S");
Choice 5
JMenuItem save = new JMenuItem("Save");
save.addShortcutKey( new KeyStroke(KeyStroke.S | KeyStroke.CTRL_KEY) );
GridBagConstraints gbc1 = new GridBagConstraints(1,1,2,1,1,3,10,1,new Insets(5,5,5,5),1,1);
gbl.addLayoutComponent(jb,gbc1);
In regards to the above code, which one of the following indicates jb's grid position?
Choice 1
Grid position 2,1
Choice 2
Grid position 1,2
Choice 3
Grid position 1, 1
Choice 4
Grid position 10, 1
Choice 5
Grid position 1, 3
GridBagConstraints gbc1 = new GridBagConstraints(1,1,2,1,1,3,10,1,new Insets(5,5,5,5),1,1);
gbl.addLayoutComponent(jb,gbc1);
In regards to the above code, which one of the following indicates jb's grid position?
Choice 1
Grid position 2,1
Choice 2
Grid position 1,2
Choice 3
Grid position 1, 1
Choice 4
Grid position 10, 1
Choice 5
Grid position 1, 3
Which one of the following is necessary when changing an Applet to a standalone application?
Choice 1
Add a no-argument constructor.
Choice 2
Remove the init(), start() and stop() methods.
Choice 3
Remove "extends JApplet" or "extends Applet".
Choice 4
Add a main() method.
Choice 5
Change the import statement so that it imports an Application container rather than Applet or JApplet.
Which one of the following adds the String "Java" to the JComboBox jcb?
Choice 1
ComboBoxModel cbm = jcb.getModel();
cbm.addItem("Java");
Choice 2
jcb.setText("Java");
Choice 3
ComboBoxModel cbm = jcb.getModel();
cbm.add("Java");
Choice 4
jcb.add("Java");
Choice 5
jcb.addItem("Java");

I'll have a go but I am not saying they are all correct...
Question 1.
Which one of the following converts the Image i into the BufferedImage bi?
Choice 3 (assuming this implements the imageobserver interface)
bi = new BufferedImage(i.getWidth(this), i.getHeight(this), 1); //1 is BufferedImage.TYPE_INT_RGB
Graphics2D g = (Graphics2D)
bi.createGraphics();
g.drawImage(i,0,0,this);Good luck with your homework...
nes
Question 2.
CardLayout
BorderLayout
FlowLayout
GridBagLayout
GridLayout
Which one of the following indicates all of the layout managers (from the list above) that allow you to set the space between the components from an instance of the LayoutManager itself?
Choice 4
BorderLayout,
FlowLayout,
GridLayout
(GridBagLayout uses GridBagConstraints to decide component spacing, card layout does not provided component spacing due to the deck nature used)
Question 3.
JFrame jf = new JFrame();
jf.setSize(400,400);
JTextField jtf = new JTextField("JTextField");
JButton jb = new JButton("JButton");
jf.getContentPane().setLayout( new FlowLayout(FlowLayout.LEFT,1,2));
jf.getContentPane().add(jtf);
jf.getContentPane().add(jb);    Which one of the following indicates the positions of the JTextField jtf and JButton jb relative to the JFrame and each other?
Choice 3 jtf is in the top-left corner of the JFrame with jb 1 pixel to the right of it.
Question 4
public void drawText(Graphics2D g, String text)
     Font f = new Font("Century Gothic", Font.BOLD, 10);
     g.setFont(f);
     g.drawString(text, 20, 20);
}    Given the above sample code, what happens if the "Century Gothic" font is NOT available?
Choice 5 A default Font object is returned and is used
Question 5.
How must do you interact with a JTextField in order to generate an ActionEvent?
Choice 4 Hit <RETURN> while the cursor is in the JTextField.
Question 6.
public class TimerTest implements ActionListener
     public static void main(String[] args)
           TimerTest test = new TimerTest();
           javax.swing.Timer timer = new javax.swing.Timer(100,test);
     public void actionPerformed(ActionEvent ev)
          System.out.println("Timer ticked.");
}    Given the above sample code, what is the result when the code is run?
Choice 5 Nothing, the Timer is not started.
Question 7.
1. JSlider slider1 = new JSlider (JSlider.VERTICAL, 0, 100, 50);
2. slider1.setPaintTicks(false);
3. slider1.setMajorTickSpacing(10);
4. slider1.setMinorTickSpacing(2);    What changes do you have to make to the above Sample code so that there are six Major Ticks and four Minor ticks between each Major Tick?
Choice 4 Replace line 2 with slider1.setPaintTicks(true); Replace line 3 with slider1.setMajorTickSpacing(20); Replace line 4 with slider1.setMinorTickSpacing(4);
Question 8.
Which one of the following defines a set of three JRadioButtons (b1, b2, and b3) so that only one JRadioButton can be selected at a time?
Choice 1 ButtonGroup g = new ButtonGroup(); g.add(b1); g.add(b2); g.add(b3);
Question 9.
Sample Code
public static void main(String args[]){ }
TYPO - should be public static void main(String[] args){ }
What is the role of the method in the code above?
Choice 2 It is the first method run when a class is run with the Java Interpreter.
Question 10.
How do you create a menu item, Save, with a shortcut key of Ctrl+S?
Choice 2 JMenuItem save = new JMenuItem("Save");
save.setAccelerator(KeyStroke.getKeyStroke(KeyEvent.VK_S,Event.CTRL_MASK));
Question 11.
GridBagConstraints gbc1 = new GridBagConstraints(1,1,2,1,1,3,10,1,new Insets(5,5,5,5),1,1); gbl.addLayoutComponent(jb,gbc1);
In regards to the above code, which one of the following indicates jb's grid position?
Choice 3 Grid position 1, 1
Question 12
Which one of the following is necessary when changing an Applet to a standalone application?
Choice 1 Add a no-argument constructor.
Choice 2 Remove the init(), start() and stop() methods.
Choice 3 Remove "extends JApplet" or "extends Applet".
Choice 4 Add a main() method.
Choice 5 Change the import statement so that it imports an Application container rather than Applet or JApplet.
mmm. not a good choice of answers. look at the following link...
http://forum.java.sun.com/thread.jsp?forum=57&thread=218096
Question 13.
Which one of the following adds the String "Java" to the JComboBox jcb?
Choice 5 jcb.addItem("Java");

What is the correct way to add styling to drag-and-drop created calendars?

I have a working instance of a rich client calendar. I generated the view with the required fields (start, stop, provider, ...), put it into the App Module, and dragged it onto a JSF page to create a calendar.
Next I created an activityScope object in a class called CalendarBean (no inheritance)
Class CalendarBean()
private HashMap<Set<String>, InstanceStyles> activityColorMap;
+..+
+public CalendarBean() {+
super();
activityColorMap = new HashMap<Set<String>, InstanceStyles>();
HashSet setEd = new HashSet<String>();
HashSet setLen = new HashSet<String>();
setEd.add("Work");
setLen.add("Home");
activityColorMap.put(setEd, CalendarActivityRamp.getActivityRamp(CalendarActivityRamp.RampKey.ORANGE));
activityColorMap.put(setLen, CalendarActivityRamp.getActivityRamp(CalendarActivityRamp.RampKey.RED));
+}+
+}+
Next, I linked this up as a backing bean and associated the ActivityStyles of CalendarBean to it:
+#{backingBeanScope.calendarBean.activityColorMap}+
I populated some records in the database with properties "Work" and "Ed', but they show default blue.
As I understand it, I need to do something with the getTags() method of the underlying CalendarActivity class, but I'm not quite sure how to do that.
Took a stab at creating a class, CalendarActivityBean, that extended CalendarActivity, and pointed all the CalendarActivity references I had to the new class, but it didn't seem to fire (in debug), and I got into trouble, when inserting records, with
public void calendarActivityListener(CalendarActivityEvent calendarActivityEvent) {
currActivity = (CalendarActivityBean) calendarActivityEvent.getCalendarActivity();
being an illegal cast
What is the correct way to add provider-based styling to drag-and-drop create calendars?
Ed Schechter

A colleague of mine was kind enough to solve this:
The calendar has ActivityStyles property = #{calendarBean.activityStyles}
CalendarBean looks something like this:
package com.hub.appointmentscheduler.ui.schedule;
import java.util.HashMap;
import java.util.HashSet;
import java.util.Set;
import oracle.adf.view.rich.util.CalendarActivityRamp;
import oracle.adf.view.rich.util.InstanceStyles;
+public class CalendarBean {+
private HashMap activityStyles;
private String dummy;
+public CalendarBean() {+
+// Define colors+
activityStyles = new HashMap<Set<String>, InstanceStyles>();
HashSet setPending = new HashSet<String>();
HashSet setArrived = new HashSet<String>();
HashSet setApproved = new HashSet<String>();
HashSet setCompleted = new HashSet<String>();
setApproved.add("APPROVED");
setPending.add("PENDING");
setArrived.add("ARRIVED");
setCompleted.add("COMPLETED");
activityStyles.put(setApproved, CalendarActivityRamp.getActivityRamp(CalendarActivityRamp.RampKey.GREEN));
activityStyles.put(setPending, CalendarActivityRamp.getActivityRamp(CalendarActivityRamp.RampKey.ORANGE));
activityStyles.put(setArrived, CalendarActivityRamp.getActivityRamp(CalendarActivityRamp.RampKey.PLUM));
activityStyles.put(setCompleted, CalendarActivityRamp.getActivityRamp(CalendarActivityRamp.RampKey.LAVENDAR));
+}+
+public void setactivityStyles(HashMap activityStyles) {+
this.activityStyles = activityStyles;
+}+
+public HashMap getactivityStyles() {+
return activityStyles;
+}+
+}+
Now, go into the Bindings tab on the calendar page, double click the calendar binding, and specify the column you've defined as the calendar's Provider in the Tags dropdown.
Should show colors.

1.4.2 - What is the correct way to format output in the java.io.PrintStream

With Java 1.4.2:
What is the correct way to format output in the java.io.PrintStream?
The following is incorrect, even though it is still used in the The JavaTM Tutorial at: http://java.sun.com/docs/books/tutorial/essential/
System.out.formatThis returns "cannot resolve the method 'format'"
Any detailed suggestions or information is greatly appreciated.

The following is incorrect, even though it is still
used in the The JavaTM Tutorial at:
http://java.sun.com/docs/books/tutorial/essential/
The whole format thing has been introduced in 1.5. The tutorial also states it's been "updated to 1.5.".
That's all I've got to say for I don't know how you can format a PrintWriter, let alone a PrintStream, prior to 1.5. I'm not really sure there is any way. Any "legacy way", that is. There almost certainly are third-party API which achieve similar results.

What are the correct steps for installing Oracle Entitlement Server SSM?

Can somebody explain what are the correct steps to install OES SSM 10.1.4.3? I have installed OES admin 10.1.4.3 and applied the CP2 patch. it is allowing me to open Entitlement Administration, where I can define the policy.
Is it sufficient to have this Entitlement Admin to call the policy from BPM? Do I need a SSM ?
When I try to configure Java SSM using ConfigTool.bat -process myssm_config.properties I am getting the following error
Is Admin in the same BEA-HOME as SSM: [default: Yes]:
Give the location of the Admin: c:\bea\ales32-admin
Enter the identity directory name which will be used: [default: CoESSM_dir]:
Enter the root node which will be used to create resources: [default: //app/policy/CoESSM_app]:
Checking if default ARME port is free: 8000
Generating policy files based on templates ...
Checking if SSM instance already present
Checking to see if SSM ARME port is free.
Checking JDBC parameters...
Checking to see if asipassword was run...
2010-03-15 18:06:59,295 [Main Thread] ERROR com.bea.security.SsmConfigTool.AlesConfig - You need to run asipassword first
2010-03-15 18:06:59,295 [Main Thread] ERROR com.bea.security.SsmConfigTool.ConfigurationTool - Error making changes: You need to run asipassword first
I have tried running the asipassword utility, but still it gives the same error. Please let me know what am I doing wrong?

Yes I have explored this pdf...but it doesn't tell how to use the policy from the BPM. My question is if I want to use the policies from BPM, then do I need to install the SSM ?
If yes, what are the correct steps of installation ?
I am getting the errors while configuring the Java SSM.
Is Admin in the same BEA-HOME as SSM: [default: Yes]:
Give the location of the Admin: c:\bea\ales32-admin
Enter the identity directory name which will be used: [default: CoESSM_dir]:
Enter the root node which will be used to create resources: [default: //app/policy/CoESSM_app]:
Checking if default ARME port is free: 8000
Generating policy files based on templates ...
Checking if SSM instance already present
Checking to see if SSM ARME port is free.
Checking JDBC parameters...
Checking to see if asipassword was run...
2010-03-15 18:06:59,295 [Main Thread] ERROR com.bea.security.SsmConfigTool.AlesConfig - You need to run asipassword first
2010-03-15 18:06:59,295 [Main Thread] ERROR com.bea.security.SsmConfigTool.ConfigurationTool - Error making changes: You need to run asipassword first
I have tried running the asipassword utility, but still it gives the same error. Please let me know what am I doing wrong?

What is the best way to configure password in Cisco IOS?

I am running IOS 15.2(4) on a 1921 Router
What is the best way to configure the password for the router? I have already tried once and managed to lock myself out of another switch. I would like to use the most secure method which encrypts the password.
Current Config:
username admin privilege 15 password 0 cisco123

Cisco IOS will not let me use a type 5 password. This is the error message I receive:
ERROR: The secret you entered is not a valid encrypted secret.
To enter an UNENCRYPTED secret, do not specify type 5 encryption.
When you properly enter an UNENCRYPTED secret, it will be encrypted.
I tried generating an MD5 hash and inputting that in and that did not work either. When I do not specify type 5 it will default to using an encrypted type 4 password.
Also, what is the difference between these two enable secret commands?
enable secret 5 password
username admin privilege 15 secret 5 password

What are the correct Time Capsule Airport Utility Disk options?

During configuration of the Time Capsule what are the correct options/settins in the Airport Utility on the Disk tab? Does File Sharing interfere with Server File Saring>

You can turn on file sharing.. it will not interfere with your server since it has a different IP address.
You can use either device password or disk password.. do not use the profiles as that complicates things.. and Apple did not build in a link to Server to use standard user login which is a great pity.. when you have an active directory type setup it .. the TC could have been made a lot more business like.. However apple really have the TC aimed at the domestic market and users without a server.
What are you intending to use the TC for?
Most people would be better buying an airport extreme rather than TC when they are running business setup.

What is the correct wording to connect to an SQL Server Express 2014 database?

I am connecting to an Access 2007 database:
oleConnection = new OleDbConnection("Provider=Microsoft.ACE.OLEDB.12.0;Data Source=C:\\...\\Db.accdb");
What is the correct wording to connect to an SQL Server Express 2014 database?
bhs67

Hello,
Please make sure you change RemoteServer with the computer name of the intended SQL Server server.
Make sure the SQL Server instance have enable TCP/IP and Named Pipes protocols. Use the following article to enable them:
http://msdn.microsoft.com/en-us/library/ms191294.aspx
Start SQL Server Browser Service using SQL Server Configuration Manager.
Hope this helps.
Regards,
Alberto Morillo
SQLCoffee.com

What is the correct way to destory a Thread?

Just wondering what is the correct way to destroy a thread? I am currently using the stop() method, but i noticed that it has been depreciated (along with other methods used to destroy a thread) when i looked at the thread documentation. Since this is so, then how can one correctly destroy a thread? Thanks in advance for the help.

There is an awful lot of bad advice in this thread about what null does. Please in future check on your own with working code before offering up misguided and very wrong advice. Particularly when your advice contradicts that previously given.
Please compile and run the following
public class Test implements Runnable{
public static void main(String args[])throws Exception{
    Test test = new Test();
    Thread t= new Thread(test);
    t.start();
    // have delay wait a few seconds to demonstrate
    Thread.sleep(3000);
    System.out.println("Setting reference to thread to null");
    t = null; // what does this do?
    // jack all
    System.out.println("Exiting main");
public void run(){
    while(true){
      System.out.println("Hello from test thread!");
      try{ Thread.sleep(750); }catch(InterruptedException iDontCareAboutThis){}
}This will output the following
C:\>java Test
Hello from test thread!
Hello from test thread!
Hello from test thread!
Hello from test thread!
Setting reference to thread to null
Exiting main
Hello from test thread!
Hello from test thread!
Hello from test thread!
Hello from test thread!
Hello from test thread!
Hello from test thread!And continues on endlessly. Setting the reference to null is NOT an answer to this problem.

What is the correct method to configure PC3500 memories?

Similar Messages

Maybe you are looking for