What is the needed analog inputs to UMI 7764
Do these signals need to be 0-10 V? +/- 10 V or what?
National Instruments motion controllers (and therefore the UMI), accept analog inputs in the -10 Volt to +10 Volt range. This means that your analog signal cannot exceed these voltage levels, but it can be anywhere within this range. You then specify the input voltage range over which the analog to digital converters (ADCs) will convert the input voltages to digital values, according to the voltage range returned by your analog signal. You can choose from any of the following ranges:
0 to 5 V
-5 to +5 V
0 to 10 V
-10 to 10 V (default)
Voltages outside of the range will clamp at the extreme values.
For more information on setting the range of your ADC channels in Measurement & Automation Explorer (MAX), please refer to the following tutorial:
Developer Zone Tutorial: ADC Settings for Motion Controllers
Hope this helps!
Best regards,
Dawna P.
Applications Engineer
National Instruments
Similar Messages
-
What are the 4 analog inputs of my umi-7764 (on the analog input terminal block)
I would like to known what are and how connect the 4 analog inputs of the anolog input terminal block of my umi-7764. I am french, so if you want to answer in french, it will be easier for me .
Sébastien,
Selon la carte de contrôle d'axe que vous utilisez (7344, 7334 ou autre), vous pouvez disposer d'entrées analogique.
Si votre carte possède des lignes analogiques (voir la documentation de celle ci), cela signifie que vous pouvez les utiliser pour 2 choses:
1. Utiliser ces lignes analogiques pour le feedback (retour en position) de vos servo moteurs. Cela veut que vous travaillez avec un servo, et que vous êtes en boucle fermé. (Pour informations, un servomoteur peut aussi asservi avec un retour en position).
2. Si vous ne faites pas d'asservissement en tension ou que vous controliez un moteur pas à pas, alors ces lignes d'entrée analogique, peuvent être utilisées comme des lignes classiques. Pour les utilisez dans ce cas, vous devez cabler
votre signal sur l'UMI (qui n'est qu'une interface entre vos signaux et la carte) de la manière suivante:
- Le point chaud du signal sur "Analog Input X"
- Le point froid du signal sur "Analog Inout Ground"
De plus si votre carte de contrôle d'axe intègre des entrées analogiques, vous pouvez configurer leur gamme dans MAX (Measurement & Automation Explorer) le range de ces voies (+/-10, +/-5, 0-5 et 0-10 V).
(Comme l'UMI est un bloc générique, assurez vous bien que votre carte possède des entrées analogiques)
Finalement, pour lire le niveau de tension sur ces entrées, il existe dans le driver NI-MOTION, la fonction "Read ADC".
sur http://www.ni.com/manuals
vous trouverez la documentation de votre matériel.
A l'adresse ci dessous, vous trouverez de l'aide concernant la configuration de votre system motion dans max:
http://zone.ni.com/devzone/conceptd.nsf/webmain/081957EE013C7A4586256B92007818E0?opendocument
Raphael TILLET
Ingénieu
r Application
NI FRANCE
Cordialement,
Raphael T -
What is the Fieldpoint analog input interchannel skew time?
I need to know what the interchannel skew is on Fieldpoint analog input modules because I need to aquire samples fairly close in time to one another simily to the typical MIO PC-based card. Also, I am wondering if the aquisitions can be externally triggered.
The FieldPoint IO modules are designed to continually sample all (4/8/16) channels and write the data to shared memory. FieldPoint controllers then read the shared memory and make the data available to the user (serial/ethernet) or controlling program (RT). There are no provisions for external triggering of ADC conversions. Nor are there provisions to prevent the user from oversampling or undersampling the shared memory (e.g. the controller reads the shared memory 5 times in-between the ADC updating a channel). The interchannel skew can be determined by taking the IO Module All Channel Update Rate (e.g. 1.08 seconds for the FP-RTD-122)and dividing it by the total number of channels (e.g. 8 for the FP-RTD-122). Thus, the delay in between any two adjacent channels
is 135 ms for the FP-RTD-122.
Ultimately, FieldPoint was designed for single point measurements and not for waveform or simultaneous measurements. The capability for triggered, simultaneous or deterministically sampled readings is not currently available in the FieldPoint system.
Regards,
Aaron -
What is the need of creating partner functions for sales document type.
Hi SAP (SD-GURUS),
Actually we create partner functions before creating customer ex: sold to party, ship to party, bill to party, and payer.
These partner functions are going to be copied into sales order while processing sales order.
Again what is the need of creating partner functions for sales document type.
Thanks&Regards
sreenivas peruruThere are some Partners you could enter at Sales ORder Level. E.g. Sales Person, Employee Responsible, Forwarding Agent, Broker, etc.
Thus these partner Determination need to be carried out at Sales Order Level & not at Customer Master level.
So we have to configure partner Determination for various levels e.g. Customer Master, Sales Order, Delivery level etc...
Hope this helps...
THanks,
Jignesh Mehta -
What is the need of creating New order type in PO
Dear Experts,
I have a doubt in MM, what is the need of creating New Order Types? Please explain with Business scenario. Thanking you,
Regards,
Elangovan.AHi Elangovan
Whenever you have a doubt like this...
--- just verify the config settings for your parameter (order type here).
---Also check whether authorizations can be given for this ?
---Do you need it for specific analysis ? Are there standard reports/listings available ?
So, some of the uses of order type are:
1) What are the parameters controlled by order type ?
It controls the number ranges and screen layouts etc. So, if you want to have different set of number ranges and different screen settings, then you may need a new order type.
2) Authorizations can be controlled with order type.
3) You can also use it in analysis/listings
Best regards
Ramki -
What is the need of the file Adobe\Acrobat\8.0\Collab\Workflows?
Hi
I am using Adobe PDF Annotation Service with Documentum.
I am facing a performance issue with the Annoration Service.
The size of the C:\Documents and Settings\<username>\Application Data\Adobe\Acrobat\8.0\Collab\Workflows is increasing by 14 KB whenever I use the service to Annotate PDF Documents.THis happens at all my client machines.
What is the need of this file in the context?
Can we do something to restrict the inflation of this particular file?
Can anybody help me to understand the process behind this?
Thanks,
SleebaHi
I am using Adobe PDF Annotation Service with Documentum.
I am facing a performance issue with the Annoration Service.
The size of the C:\Documents and Settings\<username>\Application Data\Adobe\Acrobat\8.0\Collab\Workflows is increasing by 14 KB whenever I use the service to Annotate PDF Documents.THis happens at all my client machines.
What is the need of this file in the context?
Can we do something to restrict the inflation of this particular file?
Can anybody help me to understand the process behind this?
Thanks,
Sleeba -
What is the need for setting property data inside the JMSMesage
Hi
Could anybody please let me know
*What is the need for setting property data inside the JMSMesage??
For example i have a seen a similar example as shown ??
I have seen a
Message.setStringProperty("Sport","Basketball");
and also please tell me how can the MDB recievies this property data ??
Thanks in advance .raviprivate wrote:
Could anybody please let me know
*What is the need for setting property data inside the JMSMesage??
For example i have a seen a similar example as shown ??
I have seen a
Message.setStringProperty("Sport","Basketball"); Look at the detail JMS documentation on [Message Properties|http://java.sun.com/j2ee/sdk_1.3/techdocs/api/javax/jms/Message.html] .
>
and also please tell me how can the MDB recievies this property data ?? MDB onMessage method argument is the Message object and if you look at the documentation, Message interface has getter methods to retrieve the properties. -
Hi what are the needed documents so that I can avail of Apple's one year warranty? Is the Official Receipt a must? Thanks
Not necessarily... The Serial Number will allow Apple to ascertain what they need.
Apple Warranty > http://www.apple.com/legal/warranty/
"Choose a product" and then "Choose a region" -
What is the need of xi in idoc to idoc related scenarios
Hi all,
Can any one explain me what is the need of xi in idoc to idoc related scenarios.\
we can Send Idoc with out Xi right?
Thanks,
SrinivasIDOC to IDOC Scenario
pass through idoc to idoc scenario
IDoc to IDoc Scenario with High Volumes
SM58 Error For IDOC to IDOC Scenario -
What is the need of ALE/ IDOC
Hi All,
What is the need of ALE/ IDoc and why we go for ALE?IDOC with conditions
Let me know the answers if anyone have the solution
Regards'
RameshALE (Application Linking and Enabling)
Ale Technology is SAPs technology to support distributed yet integrated processes across several SAP systems.
IDocs (Intermediate Documents) are the crux of ALE. These are the documents with the help of which data is exchanged between SAP R/3 and non-R/3 systems. As the name suggests, these documents act as intermediate storage of information, which can be sent bi-directionally. Message types are responsible for creation of Idocs.
IDocs
Data Creation in Idoc
IDocs are text encoded documents with a rigid structure that are used to exchange data between R/3 and a foreign system. Instead of calling a program in the destination system directly, the data is first packed into an IDoc and then sent to the receiving system, where it is analyzed and properly processed. Therefore an IDoc data exchange is always an
asynchronous process. The significant difference between simple RFC-calls and IDoc data exchange is the fact, that every action performed on IDocs are protocolled by R/3 and IDocs can be reprocessed if an error occurred in one of the message steps.
While IDocs have to be understood as a data exchange protocol, EDI and ALE are typical use cases for IDocs. R/3 uses IDocs for both EDI and ALE to deliver data to the receiving system. ALE is basically the scheduling mechanism that defines when and between which partners and what kind of data will be exchanged on a regular or event triggered basis. Such a set-up is called an ALE-scenario.
IDoc is a intermediate document to exchange data between two SAP Systems.
*IDocs are structured ASCII files (or a virtual equivalent).
*Electronic Interchange Document
*They are the file format used by SAP R/3 to exchange data with foreign systems.
*Data Is transmitted in ASCII format, i.e. human readable form
*IDocs exchange messages
*IDocs are used like classical interface files
IDOC types are templates for specific message types depending on what is the business document, you want to exchange.
WE30 - you can create a IDOC type.
An IDOC with data, will have to be triggered by the application that is trying to send out the data.
FOr testing you can use WE19.
How to create idoc?
*WE30 - you can create a IDOC type
For more information in details on the same along with the examples can be viewed on:
http://www.netweaverguru.com/EDI/HTML/IDocBook.htm#_Toc8400404
http://help.sap.com/saphelp_erp2005/helpdata/en/0b/2a6620507d11d18ee90000e8366fc2/frameset.htm
http://www.sappoint.com/presentation.html
http://www.allsaplinks.com/idoc_search.html
http://www.sapgenie.com/sapedi/idoc_abap.htm
http://www.erpgenie.com/sapedi/idoc_abap.htm
To Create Idoc we need to follow these steps:
Create Segment ( WE31)
Create Idoc Type ( WE30 )
Create Message Type ( WE81 )
Assign Idoc Type to Message Type ( WE82 )
Creating a Segment
Go to transaction code WE31
Enter the name for your segment type and click on the Create icon
Type the short text
Enter the variable names and data elements
Save it and go back
Go to Edit -> Set Release
Follow steps to create more number of segments
Create IDOC Type
Go to transaction code WE30
Enter the Object Name, select Basic type and click Create icon
Select the create new option and enter a description for your basic IDOC type and press enter
Select the IDOC Name and click Create icon
The system prompts us to enter a segment type and its attributes
Choose the appropriate values and press Enter
The system transfers the name of the segment type to the IDOC editor.
Follow these steps to add more number of segments to Parent or as Parent-child relation
Save it and go back
Go to Edit -> Set release
Create Message Type
Go to transaction code WE81
Change the details from Display mode to Change mode
After selection, the system will give this message The table is cross-client (see Help for further info). Press Enter
Click New Entries to create new Message Type
Fill details
Save it and go back
Assign Message Type to IDoc Type
Go to transaction code WE82
Change the details from Display mode to Change mode
After selection, the system will give this message The table is cross-client (see Help for further info). Press Enter.
Click New Entries to create new Message Type.
Fill details
Save it and go back
Check these out..
Re: How to create IDOC
Check below link. It will give the step by step procedure for IDOC creation.
http://www.supinfo-projects.com/cn/2005/idocs_en/2/
ALE/ IDOC
http://help.sap.com/saphelp_erp2004/helpdata/en/dc/6b835943d711d1893e0000e8323c4f/content.htm
http://www.sapgenie.com/sapgenie/docs/ale_scenario_development_procedure.doc
http://edocs.bea.com/elink/adapter/r3/userhtm/ale.htm#1008419
http://www.netweaverguru.com/EDI/HTML/IDocBook.htm
http://www.sapgenie.com/sapedi/index.htm
http://www.sappoint.com/abap/ale.pdf
http://www.sappoint.com/abap/ale2.pdf
http://www.sapgenie.com/sapedi/idoc_abap.htm
http://help.sap.com/saphelp_erp2005/helpdata/en/0b/2a60bb507d11d18ee90000e8366fc2/frameset.htm
http://help.sap.com/saphelp_erp2005/helpdata/en/78/217da751ce11d189570000e829fbbd/frameset.htm
http://www.allsaplinks.com/idoc_sample.html
http://www.sappoint.com/abap.html
http://help.sap.com/saphelp_erp2004/helpdata/en/dc/6b835943d711d1893e0000e8323c4f/content.htm
http://www.sapgenie.com/sapgenie/docs/ale_scenario_development_procedure.doc
http://edocs.bea.com/elink/adapter/r3/userhtm/ale.htm#1008419
http://www.netweaverguru.com/EDI/HTML/IDocBook.htm
http://www.sapgenie.com/sapedi/index.htm
http://www.allsaplinks.com/idoc_sample.html
http://www.sapgenie.com/sapgenie/docs/ale_scenario_development_procedure.docs
go trough these links.
http://help.sap.com/saphelp_erp2004/helpdata/en/dc/6b835943d711d1893e0000e8323c4f/content.htm
http://www.sapgenie.com/sapgenie/docs/ale_scenario_development_procedure.doc
http://edocs.bea.com/elink/adapter/r3/userhtm/ale.htm#1008419
http://www.netweaverguru.com/EDI/HTML/IDocBook.htm
http://www.sapgenie.com/sapedi/index.htm
http://www.sappoint.com/abap/ale.pdf
http://www.sappoint.com/abap/ale2.pdf
http://www.sapgenie.com/sapedi/idoc_abap.htm
http://help.sap.com/saphelp_erp2005/helpdata/en/0b/2a60bb507d11d18ee90000e8366fc2/frameset.htm
http://help.sap.com/saphelp_erp2005/helpdata/en/78/217da751ce11d189570000e829fbbd/frameset.htm
http://www.allsaplinks.com/idoc_sample.html
http://www.sappoint.com/abap.html
http://help.sap.com/saphelp_erp2004/helpdata/en/dc/6b835943d711d1893e0000e8323c4f/content.htm
http://www.sapgenie.com/sapgenie/docs/ale_scenario_development_procedure.doc
http://edocs.bea.com/elink/adapter/r3/userhtm/ale.htm#1008419
http://www.netweaverguru.com/EDI/HTML/IDocBook.htm
http://www.sapgenie.com/sapedi/index.htm
http://www.allsaplinks.com/idoc_sample.html
http://http://help.sap.com/saphelp_erp2004/helpdata/en/dc/6b835943d711d1893e0000e8323c4f/content.htm
An IDoc is simply a data container that is used to exchange information between any two processes that can understand the syntax and semantics of the data...
1.IDOCs are stored in the database. In the SAP system, IDOCs are stored in database tables.
2.IDOCs are independent of the sending and receiving systems.
3.IDOCs are independent of the direction of data exchange.
The two available process for IDOCs are
Outbound Process
Inbound Process
AND There are basically two types of IDOCs.
Basic IDOCs
Basic IDOC type defines the structure and format of the business document that is to be exchanged between two systems.
Extended IDOCs
Extending the functionality by adding more segments to existing Basic IDOCs.
To Create Idoc we need to follow these steps:
Create Segment ( WE31)
Create Idoc Type ( WE30)
Create Message Type ( WE81)
Assign Idoc Type to Message Type ( WE82)
imp links
http://www.allsaplinks.com/idoc_sample.html
http://www.sapgenie.com/sapedi/idoc_abap.htm
www.sappoint.com
--here u can find the ppts and basic seetings for ALE
http://sappoint.com/presentation.html
www.sapgenie.com
http://www.sapgenie.com/ale/index.htm
Check these links.
http://help.sap.com/saphelp_erp2004/helpdata/en/dc/6b835943d711d1893e0000e8323c4f/content.htm
http://www.sapgenie.com/sapgenie/docs/ale_scenario_development_procedure.doc
http://edocs.bea.com/elink/adapter/r3/userhtm/ale.htm#1008419
http://www.netweaverguru.com/EDI/HTML/IDocBook.htm
http://www.sapgenie.com/sapedi/index.htm
http://www.sappoint.com/abap/ale.pdf
http://www.sappoint.com/abap/ale2.pdf
http://www.sapgenie.com/sapedi/idoc_abap.htm
http://help.sap.com/saphelp_erp2005/helpdata/en/0b/2a60bb507d11d18ee90000e8366fc2/frameset.htm
http://help.sap.com/saphelp_erp2005/helpdata/en/78/217da751ce11d189570000e829fbbd/frameset.htm
http://www.allsaplinks.com/idoc_sample.html
http://www.sappoint.com/abap.html
http://help.sap.com/saphelp_erp2004/helpdata/en/dc/6b835943d711d1893e0000e8323c4f/content.htm
http://www.sapgenie.com/sapgenie/docs/ale_scenario_development_procedure.doc
http://edocs.bea.com/elink/adapter/r3/userhtm/ale.htm#1008419
http://www.netweaverguru.com/EDI/HTML/IDocBook.htm
http://www.sapgenie.com/sapedi/index.htm
http://www.allsaplinks.com/idoc_sample.html
http://www.sapgenie.com/sapgenie/docs/ale_scenario_development_procedure.docs
Please check this PDF documents for ALE and IDoc.
http://www.sappoint.com/abap/ale.pdf
http://www.sappoint.com/abap/ale2.pdf
http://help.sap.com/printdocu/core/Print46c/en/data/pdf/BCMIDALEIO/BCMIDALEIO.pdf
http://help.sap.com/printdocu/core/Print46c/en/data/pdf/BCMIDALEPRO/BCMIDALEPRO.pdf
http://help.sap.com/printdocu/core/Print46c/en/data/pdf/CABFAALEQS/CABFAALEQS.pdf
http://help.sap.com/printdocu/core/Print46c/en/data/pdf/BCSRVEDISC/CAEDISCAP_STC.pdf
http://help.sap.com/printdocu/core/Print46c/en/data/pdf/BCSRVEDI/CAEDI.pdf
Check below link. It will give the step by step procedure for IDOC creation.
http://www.supinfo-projects.com/cn/2005/idocs_en/2/
Regards, -
Can any body tell me what is the need of creating shipping Instruction
Hi Everybody,
Can any body tell me what is the need of creating shipping Instruction in Material Management & where it is used.
Menu path -> IMG -> Material Management -> Purchasing - > Material Master - > Define Shipping instruction.
2. What is the use of Manufacturer Part Profile & how it is used in the SAP system.
Menu path -> IMG -> Material Management -> Purchasing - > Material Master - > Define Manufacturer Part Profile.
Thanks & Regds.....
RashmiThis characteristic describes the packaging and shipping requirements that have to be fulfilled by the vendor
The instructions issued to a vendor regarding the shipment or packing of ordered goods.
o CO coil
o NE unpacked
o NT nylon net
A manufacturer part profile contains indicators and control parameters, which define the conditions for using (inventory-managed or non-inventory-managed) manufacturer parts in the procurement process.
The manufacturer part profile specifies how manufacturer parts (MPN materials) can be used in the procurement process.
The manufacturer part profile is assigned to the master record for a firm's own inventory-managed material.
Among other things, it determines whether:
u2022 The MPN material or the inventory-managed material is to be entered in a purchase order
u2022 Info records can be created for the MPN material or the firm's own material
u2022 The MPN material can be changed during the procurement process -
What is the need of workflow tab in composite role.
I have created one composite role. For that i have assigned two user defined roles. By clicking those roles it is showing one extra tab called workflow. Then what is the need of this workflow tab in a role and what it contains.
Hello Kumar,
Check these links for this
http://help.sap.com/saphelp_nw04s/helpdata/en/07/5430fbdb39fb4d9abb56754e039d0d/content.htm
http://help.sap.com/saphelp_nw04s/helpdata/en/ab/e70538389511d5974400a0c930dcc1/content.htm
Award points if helpful,
Regards,
Raju. -
What is the need for calling default constructor by JVM?
What is the need for calling default constructor by JVM? why the JVM should intiializes default values to the data
fields if the constructor is not there in our class?mahar wrote:
What is the need for calling default constructor by JVM? Huh? The JVM does not need to call the default constructor. It needs to call a constructor.
You decide which one by the way you use "new".
why the JVM should initialize default values to the data fieldsHuh?
... if the constructor is not there in our class?Huh? The default constructor is always there. It may be private but it is still there. -
What is the Need for communication between Flex ActionScript to Javascript
Hi ,
Flex has made it communication possible from FLEX Mx:script to Java Script .
Can anybody could please tell me what is the need or any scenario for communication Flex with Javascript
Thanks in advance .1- Printing in Flex is terrible (although for simpler requirements it can do fine), true, but it's not incredibly better elsewhere in the browser unless I'm missing the point. This can be gotten around for many by streaming PDFs or Excel spreadsheets from a server, though.
2- If it has to be web, I guess you're stuck. If it can be an installed app (AIR) I'd prefer to hook into Java. Like I said, there may be some limited specific uses, but good reasons to base the majority of your app on JS hacks are hard to come by. -
HT1222 Since I'm an American, what's the need for me to update?
Since I'm an American, what's the need for me to update?
How does the new update apply to me?What update are you referring to? If you mean iOS 6.1.3, there are a number of security updates that apply to all iOS devices:
http://support.apple.com/kb/HT5704
If that's not what you mean, please explain further.
Regards.
Maybe you are looking for
-
Multiple iPhoto libraries from external drive. How to work with them all
I'm not an expert user so forgive me. But I have tons of pictures and videos of family. I've had to save 2 libraries on an external drive and going on my 3rd. I had to do it because the computer was running super slow and giving me warnings. Each lib
-
Oracle.jbo.JboException: JBO-3300 on Jdevelooper 9.0.2.8
Hi All, When i tried to run my test.jpr project, project get compiled successfuly and run first index.jsp but when i click any link on index.jsp it gives an error oracle.jbo.JboException, msg=JBO-33001: Cannot find the configuration file /org/act/epr
-
Book on oraclebi spreadsheet add-in
Does anyone know if there's any commercial book (not manual, readme, online help) specifically covering the add-in? djoni
-
Feeling ripped off by the on-site technician labor fee
First, let me start by saying I am not a person who complain just because I have been charged with a service fee. I won't complain if the fee is not a huge amount. Sometimes I am charged with hidden fees here and there, but if the amount is a few buc
-
Solution Manager Upgrade to SPS25
Hello, We are preparing to upgrade our current installation of Solution Manager 7.0 to SPS25. Is there anything we need to do with our existing maintenance and implementation projects prior to installing the upgrade? Thank you for your recommendati