What is the output from AN300?

I'd like to know the output of car charger AN300. Both mA and V.

http://www.phonesonline.ie/Product.asp?ProductID=1207 5V and 700mA.Follow link for more info.

Similar Messages

What is the proper interpretation of the output from PID vi?

Can someone clarify the meaning of the output from the NI PID vi's? From the documentation for the PID control toolkit, it appears that the output is an absolute quantity and not a delta (change) to the previous output. The problem I have is that if I am running proportional control only, and the controller is moving into a steady cooling air flow rate to achieve my setpoint temperature, the error goes to zero and the output from the controller drops to zero. This completely ruins the temperature control.
Simply: assume that the output to the control valve I am using needs 12mA (4-20mA controlled) constant value (flow rate) to maintain my setpoint. When the error goes to zero, the controller output goes to zero. This, of course, leads to terrible oscillation etc.
Other PID implementations I have used are all delta (change) based. In other words, you calculate a P, I, and D correction to the previous output.
What am I missing? All of the NI labview PID examples use the output directly to drive I/O, and never use it as a change (delta).
I read this newsgroup's archives and found a similar question, but the answer was not helpful.
thanks much in advance!

Hi Darth,
You have read the documentation correctly. The output of the PID VI is an absolute value. If you are using a P algorithm then you will need to use the PID Output Rate Limiter VI to control the rate of the oscillation. Your other option is to use a PID algorithm rather than just the P algorithm. The I and D portion of the PID algorithm are based on the current and previous error and output respectively. For further information on how the PID output is calculated please reference chapter 2 of the LabVIEW PID Control Toolset User Manual
Hope this helps!
Brooks W.
National Instruments

What is the best way to run two programs simulataneously using the output from one to run the other?

I just kind of wanted to get an opinion from some people on here. I have two main VIs. The first is a DAQ system that reads 99 different sensors and feeds that data into an array. The second is a real-time processing system that is designed to take the array and do numerous calculations. Both VIs output data to the front panel that I want to see, so I don't want to just use one as a SubVI.
Is there a simple way to run both VIs, using the output from the DAQ system to feed the processor so that you can easily see the front panels of both VIs? I had considered just copying the real-time processor code into the DAQ VI, but I'm worried the resultant VI will be very large and unsightly.
On a side note, am I over thinking this? Excuse me if this is a rather dumb question, it's been a long week...aaaand it's Wednesday.
Solved!
Go to Solution.

There are a number of ways that you can go about this, but having both front panels open isn't a problem (assuming there is screen space!). Both could be sub-vi's of another "calling" vi, with their front panels set to open when called. The data from the DAQ side can be sent to the other through a number of ways, "producer-consumer" (many threads about this topic, examples in the LabVIEW examples, etc.) is one of the more robust techniques. If created correctly it allows one to run at a different rate than the other, although if the producer is "producing" much faster than the consumer can "consume" it will end up with problems.
I guess I type too slowly
Putnam
Certified LabVIEW Developer
Senior Test Engineer
Currently using LV 6.1-LabVIEW 2012, RT8.5
LabVIEW Champion

I am trying to display the output from my ipod touch on apple tv. i can get the audio but no video. please help

i am trying to display the output from my ipod touch on apple tv. i can get the audio but no video. Thank you for any advice.

What output are you trying to get to your tv?

Cannot read the output from windows command.

Hello
I have the following classes
package cmd;
import java.io.IOException;
public class CMD {
    public CMD(){
        ProcessBuilder pb = new ProcessBuilder()
        .command("cmd.exe","/c","del *.*")
        .redirectErrorStream(false);
        Process p;
        try {
            p = pb.start();
            StreamGobbler errorGobbler = new StreamGobbler(p.getErrorStream(), "ERROR");
            // any output?
            StreamGobbler outputGobbler = new StreamGobbler(p.getInputStream(), "OUTPUT");
            // start gobblers
            outputGobbler.start();
            errorGobbler.start();
        } catch (IOException e) {
            // TODO Auto-generated catch block
        System.out.println("eee "+e.getMessage());;
    public static void main(String[] args) {
        System.out.println("x");
        new CMD();
        System.out.println("x");
and
package cmd;
import java.io.BufferedReader;
import java.io.IOException;
import java.io.InputStream;
import java.io.InputStreamReader;
public class StreamGobbler extends Thread {
    InputStream is;
    String type;
    StreamGobbler(InputStream is, String type) {
        this.is = is;
        this.type = type;
    @Override
    public void run() {
        try {
            InputStreamReader isr = new InputStreamReader(is);
            BufferedReader br = new BufferedReader(isr);
            String line = null;
            while ((line = br.readLine()) != null)
                System.out.println(type + "> " + line);
        catch (IOException ioe) {
            ioe.printStackTrace();
Please note that I cannot seee the output from wndows command : del *.* and the java class execution does not finished.
I I will replace the above command with the dir command then the output of the command is visible.
Would you give me a hint about how to modify the above clases in order to parse the output of the del *.* ?
Please note that the above example is important because I am developping a tool and it is mandatory for that tool to parse the output from a windows batch command.
Best regards,

Please note that I cannot seee the output from wndows command : del *.* and the java class execution does not finished.
I I will replace the above command with the dir command then the output of the command is visible.
Would you give me a hint about how to modify the above clases in order to parse the output of the del *.* ?
No - but I will give you a hint about ProcessBuilder and how to develop software properly.
Hint #1: Don't try to automate something that you don't know, or understand, how to do manually.
a. Do you know how to execute 'del *.*' manually in a command window?
b. Did you try that manually to see what happens?
My guess is 'no'. If you had you would know that the response to a 'del *.*' command is going to be this:
Are you sure (Y/N)?
And your 'java class execution' doesn't finish because the 'del' command is waiting for you to answer that question.
Hint #2: Don't try to use ProcessBuilder for an application that requires console input unless you first know how to provide that console input via your Java code.
Your code will wait forever since it does NOT answer that question.
Search the net and The Java Tutorials and you can find examples of executing command line utilities. Then try those examples first and make sure that:
1. They work for you
2. You understand HOW they work
Then you can modify those examples to do what you want to do.

While recording a guitar do not record the output from other tracks

Hi all,
I'm an audition/recording newbie. I have Audition CC. I have recorded one guitar track. and now I'd like to record another one. The problem is that when I try to record it the output from the other one gets recorded as well. I do want to hear the output from the first track while recording track 2 but I want only to record my guitar playing in track 2.
Thank you.

The basic problem here is not actually caused by Audition, but by your sound device mixer, which appears to be letting you record everything you hear - so that will be the guitar part you are playing, and also the replayed tracks that you've already recorded. In Windows, the fix for this is generally to make sure that the recording source is set to be just the input you are using, and not 'what you hear' or whatever it is on your device. The playback part of the mixer should let you monitor both the wav playback and your source, which is what you need to be doing - it's only the record settings you need to look at.
If you are using a Mac though, I can't help you because I don't know anything about how they work from that POV, but I'd imagine that it must be similar.

What are the output type and Tcodes?+

What are the output type and Tcodes?

hi,
ex-how to config output type.
You will assign output types using Transaction NACE.
Do the follow steps to assign output type
1)Select Application Type V2 which will have description Shipping.
2)Click on Output types button.
3)Go to change mode by pressing Ctrl+F4.
4)Select one output type which already exists
5)Do Copy As(F6)
6)Give your output type against Output Type field.
7)Under General data Tab, Give Program and Form routine and Save the data.
i think it a work of functional guy but at senior level i think it is not a big deal for abaper.
Check the following documentation
In NACE t-codewe have the application for each one. based on the application output type can be defined, based on output type script and print progrma can be defined.
If suppose data can be read from EDI then we should go for condition records.
So whenever we execute the script first composer checks the output type and then execute the program. in program whenever opn form FM will be populate then script will open first. After that again program till another FM will populate if it then script will populate........like it is cycle proces. Composer does all these things and at last it will submit that output to spool.
Go to the Transaction NACE.
choose the related sub module.. like billing or shipping
doubel click on Output Types
Choose the Output Type for which whcih you wanted your script to trigger
Then select the Output Type and double click on Processing Routine
Then go to create new entries--> Select the Medium (1- print output), then enter your Script and Print Program detls --> Save and come out
Now go to the Transaction (for which you have created the output type)... Issue output--> Select the output type --> Print....
Device Types for SAP Output Devices (Detail Information)
Definition
The device type indicates the type of printer to be addressed. When you define an output device, choose the name of the device type that was defined in the SAP System for your printer model, such as Post2 for a PostScript printer. In the case of frontend printing under Microsoft Windows, you can also use the generic (device-independent) device type SWIN.
The system uses the information in the device type to convert a document from the internal SAP character representation (spool request in OTF or in text format) to a device-specific, print-ready data stream (output request). Since a device type specifies attributes that apply to all devices of a certain model, it can be shared among device definitions. For example, all devices in the SAP spool system that are compatible with Hewlett-Packard LaserJet IIID printers would use the HPLJIIID device type.
You should not confuse the device type with the printer driver. The device type is the total of all attributes of an output device that the SAP System must know to control the output device correctly, such as control commands for font selection, page size, character set selection, and so on. These attributes also include the printer driver that SAPscript/Smart Forms (the SAP form processor) should use for this printer. The SAPscript printer driver that is to be used for devices of this type for output formatting is therefore only an attribute that the device type specifies.
How do I choose the correct device type?
In most cases, the SAP System already provides the appropriate device type for the printer type for the printer model that you want to use.
These standard device types are completely defined and need no modification or extension before you use them in device definitions.
You can also download missing device types from the sapserv server. For a current list of the supported device types, see SAP Note 8928 in the SAP Service Marketplace.
Most printers can be controlled using a generic format, such as PostScript. They can be switched to a mode that is compatible with one of the standard printers for which an SAP device type is available. In this case, a supported model is emulated.
Almost all printers are delivered with Microsoft Windows printer drivers. The system can control these printers with the generic (device-independent) device type SWIN. The Microsoft Windows spool system then performs the processing of the print data.
If the specified device types are not available, and generic device types cannot be used, you must create your own device type or edit a copy of an existing device type. We recommend that only those with specialist knowledge of the SAP Spool System and printer driver code do this. For more information, see Defining a New Device Type .
Attributes of a Device Type
A device type is distinguished by the attributes listed below. If you change an existing device type or create a new device type, you must change at least some of these attributes.
Character set: A character set specifies the codes with which characters must be represented in the print-ready output stream (output request). This code replaces the generic SAP characters set that is used internally by the SAP spool system (spool request).
Printer driver: You can specify different printer drivers for printing SAPscript documents and ABAP lists.
Print controls: Print controls represent printer operations, such as boldface or changing the font size. These print control are replaced by printer-specific commands during the creation of the output request from a spool request.
Formats: Formats specify the format supported by the SAP system. The system differentiates between SAPScript formats (DINA4 and LETTER) and ABAP list formats (X_65_132 = 65 rows/132 columns).
Page format: A page format is the interface between a format and SAPscript. It specifies the paper dimensions with which SAPScript can calculate the row and column lengths.
Actions: Actions are output device-specific commands that are required for the implementation of a format. The action printer initialization, for example, can contain a printer command with which the number of rows on a page is defined. There is a set of actions for every format supported by a device type.
regards
siva

Reading the output from a object running in the local machine.

Reading the output from a object running in the local machine.
By using a signed applet i am lunching a small application that returns an image object, how to read that without storing it in the hard disk.
Which means i need to read the image object return by the local application using applet or jsp .
i am using tomacat and an html page with an applet with it to lunch the application.

You can write that image in a binary format using OutputStream for System.out and then read it in your applet.

Getting the output from a Perl script using Runtime.exec

I cannot get the output from a perl script using Java. Can someone PLEASE help?
I used the following code:
Process p = Runtime.getRuntime().exec("C:\\Perl\\bin\\Perl.exe script.pl) ;
InputSream in = p.getInputStream();
b...
do
System.out.println(b);
while ((b = in.read()) > 0)
But there is no way that I get the output in the inputstream. If I use the command "cmd script.pl", the output is displayed in the Dos box, but also not in the inputstream.
I will appreciate any help.

Try this
Process p = Runtime.getRuntime().exec("C:\\Perl\\bin\\Perl.exe script.pl) ;
BufferedReader rd = new BufferedReader(new InputStreamReader(p.getInputStream()));
String str;
while((str=rd.readLine())!=null){
System.out.println(str);
Manu

Is it Possible to upload the output from Oracle reports To Access database

Hi All,
Wish you All a Very Happy New Year.
I have a query.Is it possible to
upload the output from the Oracle reports
to the Access database???
Any suggestions would be appreciated.
TIA
sg

Hi sg,
Research the DDE option.
Dynamic Data Exchange (DDE) is a mechanism by which applications can communicate and exchange data in Windows.
I have imported data into the excel spreadsheet using DDE built in functions. I am sure it can work with MS Acess as well. If not, then you need to create a 2 step process .. reports -> excel -> access.

What are the benefits from upgrading from Acrobat 9 Pro Extended to Acrobat11 Pro?

What are the benefits from upgrading from Acrobat 9 Pro Extended to Acrobat11 Pro?

Acrobat is a program used by a wide variety of users for a even wider number of purposes. So if we simply gave you a feature list, that wouldn't be very helpful.
Tell us how you use Acrobat, and what you do with it, and we can suggest improvements that were made in Acrobat X and XI Pro.

Openshot + Blender: No frame was found in the Output from Blender

Can't get this to work. Anyone know why?
Using OpenShot version 1.4.0
blender -v
Blender 2.61 (sub 0)
build date: 2012-01-05
build time: 10:31:02
build revision: unknown
build platform: Linux
build type: Release
build c flags: -march=x86-64 -mtune=generic -O2 -pipe -fstack-protector --param=ssp-buffer-size=4 -D_FORTIFY_SOURCE=2 -fopenmp -msse2 -msse -pipe -fPIC -funsigned-char -fno-strict-aliasing -Wall -Wcast-align -Werror=declaration-after-statement -Werror=implicit-function-declaration -Werror=return-type -Wstrict-prototypes -Wno-char-subscripts -Wno-unknown-pragmas -Wpointer-arith -Wunused-parameter -Wwrite-strings -Wno-error=unused-but-set-variable
build c++ flags: -march=x86-64 -mtune=generic -O2 -pipe -fstack-protector --param=ssp-buffer-size=4 -D_FORTIFY_SOURCE=2 -D__STDC_CONSTANT_MACROS -fopenmp -msse2 -msse -pipe -fPIC -funsigned-char -fno-strict-aliasing -Wall -Wno-invalid-offsetof -Wno-sign-compare
build link flags: -pthread
build system: CMake
Blender command: blender -b '/usr/lib/python2.7/site-packages/openshot/blender/blend/blur.blend' -P '/home/user/.openshot/blender/fdd1c574-44dd-11e1-bf0d-54e6fc88c972/blur.py'
Traceback (most recent call last):
File "/home/user/.openshot/blender/fdd1c574-44dd-11e1-bf0d-54e6fc88c972/blur.py", line 150, in <module>
bpy.context.scene.render.file_format = params["file_format"]
AttributeError: 'RenderSettings' object has no attribute 'file_format'
No frame was found in the output from Blender
Blender render thread finished
Last edited by whoops (2012-01-22 09:47:37)

yes, that is correct that it crashes with the new code when i have both made it a separate library function node and when i incorporated it into an existing code. the odd thing is that it actually seems to work now. i believe that i was using the wrong environment to call the new codes, which is why whenever i tried to revert to the original code previously, it still crashed. it seems that in order to be called, i need to use Deployment rather than Development and ppc instead of i386 in the active configuration and architecture in Xcode, respectively. while playing around with the iphone app, it must have reset my defaults to a non-labview friendly form. so now that i've got that part of the code working, i need to find out why it's still crashing on me. at first, i thought it must be the random number generator, but testing that separately in the code works just fine, so there must be something internal in the code. probably a memory allocation fault. but now that i can actually get everything running once more, i should be able to sort that issue out myself.
thank you very much for the help. sorry i didn't actually have anything to fix, unfortunately. i'm going to spend some time trying to debug this section of code to find where the fault lays. i may come back if i cannot find it in there, but hopefully it will not come to that.
take care and many thanks,
justin

Need to fetch results as the output from QGA2

Hi Gurus,
My scenario is that i need to develop an interface in which I would send Material,Plant,MIC and Period from one system to SAP R/3 and I need to fetch the output as I get the output from QGA2 while i enter the above mentioned fields.
Input: Material,Plant,MIC and Period
Output:
1) Inspection Start Date
2) Inspection Lot number
3) Material
4) Material Description
5) UD code and code group
6) Quality Score( at inspection lot level)
7) UD code text
8) Valuation of characterstic
9) System Status of lot
10) Characterstcic description
11) Operation Number at which charaterstic was inspected
12) Characterstic Number inspected
Please let me know any BADI or FM which could help me in fetching out these values as standard QGA2 transaction does fetch out these values.
Thanks

hi
Please check
BAPI_INSPCHAR_GETREQUIREMENTS
BAPI_INSPCHAR_GETRESULT
BAPI Modify result lot inspection
Regards
Sujit

Can the output from ADC port power a HDTV

This is part of my other post http://discussions.apple.com/thread.jspa?threadID=2222857&tstart=0
*I've been told that the output from an ADC port is not sufficient to power a HDTV.*
I have my ADC port connected by a ADC/DVI adaptor cable to a HDMI port on my HDTV.
Is this correct?
Can anyone confirm it?

This is the update for some NVIDIA cards.
<http://docs.info.apple.com/article.html?artnum=120168>

The bookmark tab went from the right side to the left side. I did not change that. what cause the change from the right side to the left side?

The bookmark tab went from the right side to the left side. I did not change that. what cause the change from the right side to the left side? Also the the Mozilla Firefox tab on the upper left hand corner changed.
Its was a red colored tab and now its blue in color. I did not change any thing!

Hey jimmiet,
There were some recent ui changes around the downloads manager. What version where you on before? Anyway, you can customize things in Firefox really easily. Take a look at [[Customize Firefox controls, buttons and toolbars|this article on customizing Firefox]] for details. Should be a piece of cake to move the bookmarks button.
As for the color of the button, you might be in [[Private Browsing - Browse the web without saving information about the sites you visit|Private Browsing]] mode. That changes the color of the button from orange to a purplish color.
Matt

What is the output from AN300?

Similar Messages

Maybe you are looking for