What is the procedure for storing iPads over the summer
What is the procedure for storing iPads over the summer
Lock them up in a cart. Power off completely. If you don't have enough iPad carts any secure area will do - see environmental requirements below. You will just have to recharge each one next fall as they will not retain enough power to turn back on.
Operating temperature: 32° to 95° F (0° to 35° C)
Nonoperating temperature: -4° to 113° F (-20° to 45° C)
Relative humidity: 5% to 95% noncondensing
Maximum operating altitude: 10,000 feet (3000 m)
Similar Messages
-
What is the best practice for storing iPads over the summer?
Over the summer break do iPads need a maintenance charge or can they be charged to full, stored over the summer, and then a week or so before school charged again for deployment? Thanks.
Generally, it's not a good idea to charge Li-P batteries fully prior to long-term storage. A more correct method is to have them charged between 40-60% before long-term storage. Be sure to shut off the devices fully by holding the power button down until the Power Off screen appears.
-
I recently used the computer for I player over the TV, but when removing the external speakers the internal speaker appears to have stopped working and when going on to system preferences and sound I am only given the option of digital out put. Help
Do you see a red light shining in the headphone port?
-
In planning to upgrade from OS 10.4.11, to 10.6 Snow Leopard , which now seems to be due I am a bit anxious not to confuse my current
data storage of pictures, films, music, documents and graphics.
My query centres around: Must I fully reformat my HD, have major backups done and set aside, before inserting
my 10.6 diskette? must I uninstall certain programs before just backing up?
OR
will I come across to the Snow Leopard by just entering it over my old 10.4.11 left still in place.
My iMac desktop is 6 years old, dec. 2006, Intel duocore. I kindof hope not to have to buy another one quite yet..
Please wise men/women advise!?I am a bit anxious not to confuse my current data storage of pictures, films, music, documents and graphics.
Be certain to have at least 2 backups, one a clone of the drive that you can boot from.
Must I fully reformat my HD...
No.
have major backups done and set aside, before inserting my 10.6 diskette?
Not unless all your stuff is important... meaning a very good idea to Backup first.
must I uninstall certain programs before just backing up?
Mostly not a worry, some 3rd party things will likely need updating after the Install.
My iMac desktop is 6 years old, dec. 2006, Intel duocore.
If it's a core Duo & not a Core2Duo, then it'll only run in 32 bit mode.
Snow Leopard/10.6.x Requirements...
General requirements
* Mac computer with an Intel processor
* 1GB of memory (I say 4GB at least, more if you can afford it)
* 5GB of available disk space (I say 30GB at least)
* DVD drive for installation
* Some features require a compatible Internet service provider; fees may apply.
* Some features require Apple’s MobileMe service; fees and terms apply.
Which apps work with Mac OS X 10.6?...
http://snowleopard.wikidot.com/
It's been pulled from the online store & Apple Stores, so you have to call Apple to buy it, last I heard.
Call Apple Sales...in the US: 1-800-MY-APPLE. Or Support... 1-800-275-2273
Other countries...
http://support.apple.com/kb/HE57 -
If I disable the passcode by accident, can I restore the iPad and not lose my pictures?
If you haven't backed it up, neither to your computer's iTunes nor to iCloud, then unfortunately you won't have a copy of the photos to restore back.
For anything that you've downloaded from iTunes, then you may be able to re-download/some of them via the Purchased tabs in the App Store and iTunes store apps. -
I was downloading the update for my ipad. The wifi stopped working and when I try to enter my password it says cannot connect. The download won't finish unless I'm connected to my wifi. Any suggestions?
First restart your WiFi router.
You can also try resetting your iPad by simultaneously pressing and holding the Home and Sleep/Wake buttons until you see the Apple Logo. This can take up to 15 seconds so be patient and don't release the buttons until the logo appears.
Try again to see if the problem persists. -
What are the procedures for getting Apple to wipe the data off my original ipad I bought two years ago. I had it stolen from a hotel room over the weekend and it is not password protected and no I did not download app to find it.
Any hwlp would be greting appreciated!Apple can't do it, only you could potentially do it if you had enabled Find My iPad on it before it was stolen.
If it was stolen then you should report it to the police. As a safety precaution you should also change your iTunes account password, your email account passwords, and any passwords that you'd stored on websites/emails/notes etc. -
What is the procedure for verifying that my photos, after syncing up my iPad and my iMac, actually are in iTunes?
iTunes manages your photos between the iPad and iPhoto on the iMac. If you have things set up correctly, then the photos will go to iPhoto for safe keeping and later use.
-
What is the procedure for a hard boot of my iPod touch 4th generation
without iTunes, and without computer, and without iPod data screen?
6 months after purchase I updated my iPod touch as recommend by iTunes.
It has not worked since that day. It frozen (disabled) with a "connect to
iTunes" icon displayed...that is the only thing it does. itunes does not
recognize the iPod. My Windows7 computer recognizes an Apple device.
Other computers recognize the devise but if iTunes resided on that
computer it did not recognize the iPod
I suffered a setback with deep depression and am just now getting out of it enough to do something. The depression prohibited me from taking action.
I have done every procedure recommended from Apple help and external
sources. I did this thoroughly with help for other owners and IT experts,
Apple employees etc etc. I and associates have perform reboots utilizing a
number procedure using only button on the iPod. These were unsuccessful
also have performed.
Please do not ask me to do the usual.
Online I saw a process using the buttons on the iPod to completely
reformat
the iPod. It was NOT the hold buttons for 10 sec let go of one wait 8 sec
etc. I can not find the process now...a friend showed it to me in passing
I have lost contact with him. This is the procedure, I believe, that with
enable me to update and use the iPod.You need an internet connection and likely a computer with iTunes but an iPhone, iPad or iPod touch with the FindMy iPhone App may work by:
If you previously turned on FIndMyiPod on the iPod in Settings>iCloud and wifi is on and connected go to iCloud: Find My iPhone, sign in and go to FIndMyiPhone and use Remote Wipe to erase the contents of your device. If you have been using iCloud to back up, you may be able to restore the most recent backup to reset the passcode after the device has been erased.
You can also wipe the iOS device by installing the FindMyiPhone app on another iOS device and using that app to wipe the device.
Otherwise
Disabled
Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
iOS: Forgot passcode or device disabled
If recovery mode does not work try DFU mode.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
For how to restore:
iTunes: Restoring iOS software
To restore from backup see:
iOS: Back up and restore your iOS device with iCloud or iTunes
If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
You can redownload most iTunes purchases by:
Downloading past purchases from the App Store, iBookstore, and iTunes Store
If problem what happens or does not happen and when in the instructions? When you successfully get the iPod in recovery mode and connect to computer iTunes should say it found an iPod in recovery mode.
Yo may have to go to an Apple store or a friend's house with an internet connection and iTunes. -
What should be the procedure for export parameter in CATT
Hello Everybody,
I am working with CATT, and the transactions are <b>ME21N</b> and <b>MIGO</b>.
when i am executing the transaction <b>ME21N</b> i will get the <b>Pur Ord No</b>in the message, and i would like to export <b>Pur Ord No</b> to the transaction <b>MIGO</b> as thr is one field named Purch.ord no in Migo.
what should be the Procedure for exporting a parameter?
Thanks,
Regards AfrozHello Afroz,
If you are using eCATT then following is the procedure of capturing messages in the two recording methods - TCD & SAPGUI.
=> TCD Recording Mode:
In TCD recording mode, after dobleclicking on Interface name from the TCD command in the editor on left side, just before the MSG folder DYNPRO folder will appear on right side.
-This DYNRPO folder contains the screen sequences contain the screen occurred during recording time. The last Dynpro of this folder contains the messages occurred during recording.
-Select this last folder & click on Simulate Screen icon of the same Interface editor. It will redirect to the screen where the message values exist. There select the Purchase Order Number and click on Read Field Value icon. Give the name of Export Variable.
The export variable will contain the value of the purchase order number, which can be passed to MIGO.
=> SAPGUI Recording Mode:
In the SAPGUI recording mode, the screen on which the message appeared will be used to capture the variable name, which is Purchase Order Number in this case.
If the Purchase Order Number is second variable of the message displayed(e.g. Purchase Number 2122323 Is Created)
then use the following code -
e.g.
MESSAGE ( MSG_1 ).
SAPGUI ( ME21N_4001_STEP_5 ).
ENDMESSAGE ( E_MSG_1 ).
Assing the value from the message to the export
parameter
P_EC_PurOrdNo = E_MSG_1-[1]-MSGV2.
There are total four MSGV1-MSGV4 variables. Dobule click on MSG_1 of the MESSAGE statement above. Putting the value in the export variable from the right message variable will give the purchase order number.This can be passed as MIGO.
Regards -
The procedures for restarting Mountain Lions downlown do not seem to apply in my ssituation. Before today's impass I had failed twice to download then was able to start all over again from the beginning. The system knew that I had purchased the program and allowed me to start again. Both times i lost the data (6-8 hrs per attempt) in the downloads. But that's not the problem that I am faced with now. The techniques provided to restare don't work. I can't initiate the program's download through "purchasing". The message "an error has occurred" is persistent. It don't disappear. I reboot, reenter the Apps Store. There it is again. The "pause/download" button is dead, Has anyone had a similar experience? I wish Apple would supply a disk for this program.
Welcome to the Apple Support Communities
Press Shift key on boot, delete Mountain Lion installer from Applications, open App Store > Purchases and download OS X. If it doesn't help > http://www.apple.com/support/mac/app-store/contact -
I have an iphone 4 with videos on it that I'd like to transfer to an IMac so that I can email them. (the iphone isn't in use anymore.) What's the procedure for transfering videos from an iphone to an iMac?
Connect the iPhone to your Mac with its USB cable and launch iPhoto. In iPhoto you can select which files to upload into the library. Once in the library export them out of iPhoto to a folder on the Desktop via File ➙ Export ➙ File Export with Kind=Original. That will give you copies of the videos in the folder for use outside of iPhoto.
If you want to bypass importing into iPhoto try launching Image Capture and manually upload the selected video files to the folder of your choice.
OT -
The question was, if I can also install the app on my Ipad without the need to purchase it again over the App Store?
Hi Wolly,
You would need to purchase the IOS version of Numbers in order to get it on your iPad. The version running on your Mac is an OS version and not compatible with i-devices. If you had purchased it, say, for an iPhone, it would be available on your iPad, but not a Mac. Different OS, different software.
Sorry,
GB -
Very urjent (What is the procedure for adding a table documentation to IMG)
Hi abapers,
It was very urjent,
What is the procedure for adding a table documentation to IMG entries.
(It does not have "deletion" information, but there is a section on making changes to Z tables and then updating the IMG, which presumably could be expanded for deletion of objects.)
I having the procedure, But that is not clear.
Can any body tell me step by step.
With regards.Hi,
Assign IMG Documentation
Prerequisites
You have opened the IMG structure in change mode and created an IMG activity.
Procedure
Choose the Document tab in the Assigned objects group box.
If you want to create a new document for the IMG activity, enter a name for the document and choose Create.
The name can contain alphanumeric characters and the special character "_".
You go to the text editor. Specify a package class when you save the text. You return to the previous initial screen with Back.
To use an existing document, choose the Assign other document pushbutton to the right of the document name. Choose an existing document and choose Copy.
Save the changes with IMG activity Save.
Regards,
Renjith Michael. -
What is the procedure for FDM App Migration from v9 to v11
Kindly provide the procedure for Migrating of FDM application from system 9.3.1 to v11.1.2.1.
and also Please share the documents if you folks having.
Thanks in Advance.
AVSR
Edited by: 948364 on Jul 24, 2012 5:07 AMThis is covered in the documentation pretty well I believe; however, here's the outline I followed...
- Copy FDM databases to v11 database server. (I renamed mine to follow my v11 naming scheme, but ...)
- Copy FDMApps folders over (i.e. Inbox files, scripts, etc)
- Add the applications to the new FDM. (i.e. from the login screen, pick Add Application
- Run Schema Update tool on your FDM applications
- Run User Migration Tool on your FDM applications
- Extract Oracle\Middleware\EPMSystem11R1\products\FinancialDataQuality\SharedComponents\DBSetup.zip to /Data/Scripts/Custom folder for each FDM App
- Update Machine Profiles (Workbench) (Repeat for each application)
- Add Adapter (Repeat for each application)
- Configure Adapter (Repeat for each application)
- Fix mappings*
In v9, you don't have to map dimensions you don't use. In v11 you do.... Instead of doing it that hard way and manually updating hundreds of maps, I used SQL to do it. In my environment ICP, UD3, UD1, and UD2 generally were not mapped. You would need to update this accordingly.
NOTE : I TAKE NO RESPONSIBILITY IF THE FOLLOWING CODE BLOWS YOUR STUFF UP. IT SHOULDN'T, BUT ...........
Function : Bulk Create Import File Format field creator
Author : Charles Beyer
Date : 5/10/2012
Description : This routine will automatically create a new record for each Import File Format
Corresponding to the supplied information. This may come in handy if you find
yourself needing to map a field that you have never needed before and MOST
of the locations are not actively mapping it yet.
It will also take care of the incrementing of the ImpSeq field automatically for you
Finally, it will create a * to * mapping to serve as a generic placeholder in the location's
map
Input(s) :
@FDMField = This is the FDM field name such as UD2
@FieldValue = This is the hardcoded value to start with such as [None]
--Declare Working Memory
DECLARE @FDMField varchar(50)
DECLARE @FieldValue varchar(50)
DECLARE @ImpSeq int
--Initialize Working Memory
SET @FDMField = 'UD2'
SET @FieldValue = '[None]'
SET @ImpSeq = (select top 1 ImpSeq from tBhvImpItemFile order by ImpSeq DESC)
-- Insert a Import File Field corresponding to the supplied Field Name
-- For each location that *DOES NOT* already have that field defined in their
-- Import Format
insert into tBhvImpItemFile (ImpGroupKey, ImpSeq, ImpFldFieldName, ImpFldFixedText, ImpFldStartPos, ImpFldLength)
select distinct (ImpGroupKey), 0 as ImpSeq, @FDMField, @FieldValue, 1, 1 from tBhvImpItemFile where ImpGroupKey not in (Select ImpGroupKey from tBhvImpItemFile where ImpFldFieldName = @FDMField)
-- Since for some silly reason ImpSeq is not an identity field, we need to increment the values
-- To play nice
update tBhvImpItemFile set @ImpSeq = ImpSeq = @ImpSeq + 1 where ImpSeq = 0
--Add a '* to *' type mapping
insert into tdatamap (PartitionKey, DimName, SrcKey, SrcDesc, TargKey, WhereClauseType, WhereClauseValue, ChangeSign, Sequence, VBScript)
select distinct partitionkey, @FDMField, '*','* to * Default Map', '*', 'Like', '*',0, 0, '' from tDataMap
where PartitionKey not in (select distinct partitionkey from tDataMap where DimName = @FDMField)
Maybe you are looking for
-
Driver program name for script j_1i_57f4 challan
hi .... plz i needed driver program name for delivery challan script : J_1I_57F4 . i tried to find it but since the output is displayed only from sp02 im unable to get its driver program name . i have to add certain fields in that form and correspond
-
Website not displaying correctly in chrome
Tonight, I updated muse to v2.1, build 974, cl 770522. I then made a few changes to my website www.drselenasnow.com. When I attempted to display it in chrome, there was a weird doted line on the left side of my website and the coloring of the menus w
-
Invoke node unfonctionnal after compiling
Hello, I'm currently trying to use an invoke node (I'm not using an english LabVIEW so I don't know if the words are exactly the same translated) : Obtain VI / Editor Version When I'm using it in my .VI my project work perfectly, but when I'm trying
-
Photoshop CS3 prints not central on print preview
I have CS3 and use a 3800 for my work. Whenever I set an image to print the preview displaces the image to the left and up about 1 cm. no other application I have does this. I am using windows XP on a dual core PC. From what I can tell it is a proble
-
Emoji doesnt work in texting app
when i get a emoji app and get the keyboard i try to sent a text through a texting app and the person i text doesnt get the face just a symbol can someone help me out is ther anyway it will work