What is the recommendation for cleaning ones sensor? I have a 5D.

What is the recommendation for cleaning the sensor on the 5D III
Thank you,
M

The manual recommends using a blower when the automatic cleaning fails - or better yet, sending it to Canon for service.  Sometimes - rarely - a blower will work and is the simplest and reasonably safe thing to use.
Otherwise many like the Sensor Swab solution.  It is tedious and expensive, but I have used it effectively several times - especially on the 5D that seemed more prone to spots than the newer models.  The problem I always have is going from bad to worse to finally better - a lot of patience is required and wasting or going through several of the swabs is not uncommon.  Maybe my technique sucks, but I find it takes a lot of time and swabs to be eventually be satisfied.  That said, I have never caused any damage and I have always managed to finally get the sensor clean.   Along with the swabs, good lighting and magnification (reading glasses or similar) is also necessary as the spots that look huge on a photo will be nearly invisible.
http://www.sensorswab.com/
Steve
EOS 5D MKIII

Similar Messages

  • 4.6C to ERP6.0 Upgrade - what are the recommendations for Unicode and Java

    Hi All,
    Forgive such a basic question.
    We are just beginning to look at our ERP6.0 upgrade and am unclear whether we should convert to unicode at the same time, and also what are the uses for the Java stack.
    Unicode?
    We are a single language Latin-1 site so don't need Unicode. However will it become mandatory eventually? Are we better, if we have the opportunity now, just to convert. Also I believe the Java stack is only Unicode. Does ASCII ABAP and Java Unicode complicate things?
    Java?
    Will we need it? We are proposing a technical upgrade from our 4.6c Javaless environment. Where does Java come in to play in ERP6.0? Doesn't it increase greatly the iSeries HW requirements? (I'm looking at a 2 way 550 at the moment)
    Look forward to hearing your views.
    Regards
    Steve

    Hi Stephen,
    at the moment, in a latin-1 environment Unicode is for old customers not a requrirement. This might change in 5-10 years ...
    Java: No problem at all with ASCII (in latin-1 environments)
    => there is no need for you, but you could go for it. We did several Unicode conversions already and these Latin-1 conversions are pretty easy and simple especially on iSeries, because of the special InPlace Unicode Conversion.
    ... but this can be done at any time ...
    Regards
    Volker Gueldenpfennig, consolut.gmbh
    http://www.consolut.de - http://www.4soi.de - http://www.easymarketplace.de

  • What is the biggest SAP Business One database you have ever seen?

    Hi All
    I'm trying to determine what capabilities of how big a SAP Business One database can become without it becomming to slow to work with... The reason for this question is that have a customer with a database of 27GB ... The customer have only been in production for one year, but because they roughly place 1500 sales orders each day the growth rate is big...
    So the question is simple how many GB is your largest customer and how does the system manage?

    Hi Rasmus,
    I'd agree with the above, the overall size isn't as important as the hardware that they are using. I've seen a 75GB database system which was suffering badly because they hadn't specc'd the disk I/O correctly although memory and CPU were fine (we didn't spec this, it was a site we were called in to help on when they started having issues). Of course, a larger database is going to have other issues (eg backup and restore times, patch upgrade times etc) and you'd probably want to be more proactive on database maintenance than on a smaller database (eg you don't want to have autogrow kicking in during the day so you'd need to make sure that there is sufficient space in the database at all times).
    If you are concerned about database size then one option is to clear the history tables. This can reduce the database up to 50% but, of course, you'll lose the change history.
    Database archiving is still rumoured to be coming out in the next version.
    Kind Regards,
    Owen

  • What is the recommendation for metadata, where to install the schema?

    Should we install metadata in a separate database or in application database? I am looking for experts advise, also throw any links on requirments of having a schema in application database when we install metadata in its own database..Trying to understand what is the role of additional schema in application database (fyi, this schema gets created when you register the application database).

    It has 3 possible connectors for a Monitor...
    ADC Apple Display Connector...
    DVI...
    VGA...
    ADC to DVI adapter...
    http://www.eworldsale.com/belkin-adc30m-to-dvi24f-cube-adapter855630844.html

  • HT1379 My computer I-mac is running super slow.  If I zap the PRAM it goes back to running well , briefly... a few hours, then back to super slow.  What is the resolution for this problem?  I have a Time machine that does back up well.

    My computer is running super slow.  I can correct the problem briefly by zapping the PRAM but is resumes as a problem after a few hours.  I have good time machine (capusle) backup daily.  I have done a disk verify and there doesn't appear to be anything wrong there.
    Help, this is wasting a lot of time to do simple functions.

    Hard to say what's going wrong without more information. Try the troubleshooting steps in my Mac Performance Guide. Post back if you need help with any of that or questions about the results.

  • Can I migrate from WCS 7.0 to PI 1.2. If so, what are the guidelines for migration?

    Can I migrate from WCS 7.0 to PI 1.2. If so, what are the guidelines for migration? Do we have any Instructions/steps?

    Migration from WCS 7.0 to PI 1.2 can be  performed. If the customer wants to migrate data you need to first upgrade to  NCS 1.1.1  You can download NCS 1.1.1 from Cisco.com if you have a valid service  contract.
    For the migration step involving NCS an evaluation license is  sufficient.  You can obtain an NCS evaluation license from http://www.cisco.com/go/license >  Get Demo > Network Mgmt Products > Cisco Prime NCS Evaluation License.  
    Instructions for migrating data from WCS 7.0 to NCS 1.1.1 are available in  NCS 1.1.1 Release Notes.  Do not upgrade to NCS 1.1.2 as this release is not  upgradeable to Prime Infrastructure 1.2.  If you are ordering a Cisco Prime  physical appliance (PRIME-NCS-APL-K9) be sure to select the NCS 1.1 image which  you can later upgrade to Prime Infrastructure 1.2 after you have migrated your  WCS data.
    There is a post in the support forum which can be refered.
    https://supportforums.cisco.com/docs/DOC-26972

  • What is the range for Find my iPhone

    What is the range for Find my iPhone

    Both devices have to be connected to either WiFi or Cellular and have location services enabled. Find My iPhone does not require that you be close to the phone you're trying to find. If it's connected to a network thousands of miles away, it should still work.

  • What is the price for Photoshop CS3?

    what is the price for Photoshop CS3?
    I have an old mac PRO (2008) and have problems with newer versions

    kjersti fjøsne wrote:
    I have an old mac PRO (2008) and have problems with newer versions
    Your Mac Pro 2008 should have no problems with CS6.  Not sure about CC or CC2014. Note that Adobe stills sells CS6 with a perpetual license.
    I run CS6 13.0.6 on a 2996 Mac Pro 1,1 without any problems or slowdowns whatsoever.  Just make sure you have your Mac equipped with plenty of RAM, a physically separate HD for Photoshop's scratch, and a video card with enough VRAM on it.  See my machine's specs below.
    Intel Xeon Mac Pro 1,1 [late 2006] 2.66 GHz Quad; 16 GB RAM; mutant/flashed, factory-overclocked 875/1225 "Apple PowerColor" ATI Radeon HD 5770 with 1 GB of GDDR5VRAM driving side-by-side dual 22"/24" monitors in Extended-Desktop mode; Mac OS X Lion 10.7.5 and Snow Leopard 10.6.8 boot drives; intrusive Spotlight and frivolous Dashboard permanently disabled; USB wireless 'n' available but connected to the Internet and networked via wired Ethernet. Photoshop CS6 13.0.6.

  • What software is recommended for the maintenance of mac?

    What software is recommended for the maintenance of mac?

    How to maintain a Mac
    1. Make redundant backups, keeping at least one off site at all times. One backup is not enough. Don’t back up your backups; all should be made directly from the original data. Don’t rely completely on any single backup method, such as Time Machine. If you get an indication that a backup has failed, don't ignore it.
    2. Keep your software up to date. In the App Store or Software Update preference pane (depending on the OS version), you can configure automatic notifications of updates to OS X and other Mac App Store products. Some third-party applications from other sources have a similar feature, if you don’t mind letting them phone home. Otherwise you have to check yourself on a regular basis.
    Keeping up to date is especially important for complex software that modifies the operating system, such as device drivers. Before installing any Apple update, you must check that all such modifications that you use are compatible. Incompatibility with third-party software is by far the most common cause of trouble with system updates.
    3. Don't install crapware, such as “themes,” "haxies," “add-ons,” “toolbars,” “enhancers," “optimizers,” “accelerators,” "boosters," “extenders,” “cleaners,” "doctors," "tune-ups," “defragmenters,” “firewalls,” "barriers," “guardians,” “defenders,” “protectors,” most “plugins,” commercial "virus scanners,” "disk tools," or "utilities." With very few exceptions, such stuff is useless or worse than useless. Above all, avoid any software that purports to change the look and feel of the user interface.
    The more heavily promoted the product, the more likely it is to be garbage. The most extreme example is the “MacKeeper” scam.
    As a rule, the only software you should install is that which directly enables you to do the things you use a computer for, and doesn't change the way other software works.
    Safari extensions, and perhaps the equivalent for other web browsers, are a partial exception to the above rule. Most are safe, and they're easy to get rid of if they don't work. Some may cause the browser to crash or otherwise malfunction.  Some are malicious. Use with caution, and install only well-known extensions from relatively trustworthy sources, such as the Safari Extensions Gallery.
    Never install any third-party software unless you know how to uninstall it. Otherwise you may create problems that are very hard to solve.
    4. Beware of malware. Malware is malicious software that circulates on the Internet. This kind of attack on OS X used to be so rare that it was hardly a concern, but it's now increasingly common, and increasingly dangerous.
    There is some built-in protection against downloading malware, but you can’t rely on it — the attackers are always at least one day ahead of the defense. You can’t rely on third-party protection either. What you can rely on is common-sense awareness — not paranoia, which only makes you more vulnerable.
    Never install software from an untrustworthy or unknown source. If in doubt, do some research. Any website that prompts you to install a “codec” or “plugin” that comes from the same site, or an unknown site, is untrustworthy. Software with a corporate brand, such as Adobe Flash Player, must come directly from the developer's website. No intermediary is acceptable, and don’t trust links unless you know how to parse them. Any file that is automatically downloaded from the web, without your having requested it, should go straight into the Trash. A web page that tells you that your computer has a “virus,” or that anything else is wrong with it, is a scam.
    In OS X 10.7.5 or later, downloaded applications and Installer packages that have not been digitally signed by a developer registered with Apple are blocked from loading by default. The block can be overridden, but think carefully before you do so.
    Because of recurring security issues in Java, it’s best to disable it in your web browsers, if it’s installed. Few websites have Java content nowadays, so you won’t be missing much. This action is mandatory if you’re running any version of OS X older than 10.6.8 with the latest Java update. Note: Java has nothing to do with JavaScript, despite the similar names. Don't install Java unless you're sure you need it. Most people don't.
    5. Don't fill up your boot volume. A common mistake is adding more and more large files to your home folder until you start to get warnings that you're out of space, which may be followed in short order by a boot failure. This is more prone to happen on the newer Macs that come with an internal SSD instead of the traditional hard drive. The drive can be very nearly full before you become aware of the problem.
    While it's not true that you should or must keep any particular percentage of space free, you should monitor your storage use and make sure you're not in immediate danger of using it up. According to Apple documentation, you need at least 9 GB of free space on the startup volume for normal operation.
    If storage space is running low, use a tool such as OmniDiskSweeper to explore the volume and find out what's taking up the most space. Move seldom-used large files to secondary storage.
    6. Relax, don’t do it. Besides the above, no routine maintenance is necessary or beneficial for the vast majority of users; specifically not “cleaning caches,” “zapping the PRAM,” "resetting the SMC," “rebuilding the directory,” "defragmenting the drive," “running periodic scripts,” “dumping logs,” "deleting temp files," “scanning for viruses,” "purging memory," "checking for bad blocks," "testing the hardware," or “repairing permissions.” Such measures are either completely pointless or are useful only for solving problems, not for prevention.
    Let go of the Windows mentality that every computer needs regular downtime maintenance such as "defragging" and "registry cleaning." Those concepts do not apply to the Mac platform. The machine should not be a focus of your attention. You shouldn't have to think about it at all. It should be a transparent, almost unnoticeable tool by means of which you communicate, work, and play. If you want a computer that depends on you to keep going, use a PC.
    The very height of futility is running an expensive third-party application called “Disk Warrior” when nothing is wrong, or even when something is wrong and you have backups, which you must have. Disk Warrior is a data-salvage tool, not a maintenance tool, and you will never need it if your backups are adequate. Don’t waste money on it or anything like it.

  • What is the recommended way to do multiple channel, single point sampling for control with an NI PCI-6255 in RLP?

    Hello,
    I am writing a driver for the M-series NI PCI-6255 for QNX. I have downloaded the MHDDK and have all the examples working. I have also enhanced the examples to do interrupt handling (e.g. on AI_FIFO interrupt or DMA Ring Buffer interrupt). My ultimate goal is to write a driver that I can use for closed-loop control at 500 Hz using all 80 channels of the NI PCI-6255. I may also need to synchronize each scan with a NI PCIe-7841R card for which I've already written a driver. I want an interrupt-driven solution (be it programmed I/O on an interrupt or DMA that generates an interrupt) so that the CPU is available to other threads while the 80 analog inputs are being read (since it takes quite a while). I also want to minimize the number of interrupts. Basically, I will need to collect one sample from all 80 channels every 2 milliseconds.
    There are many different options available to do so, but what is the recommended technique for the NI PCI-6255 card? I tried using the AI FIFO interrupt without DMA, but it seems to interrupt as soon as any data is in the AI FIFO (i.e. not empty condition), rather than when all 80 channels are in the FIFO, so more interrupts are generated than necessary. I tried using DMA in Ring Buffer mode to collect a single sample of 80 channels and interrupting on the DMA Ring Buffer interrupt, which appears to work better except that this technique runs into problems if I cannot copy all the data out of the DMA buffer before the next AI scan begins (because the DMA will start overwriting the buffer as it is in ring buffer mode). If the DMA is not in ring buffer mode or I make the ring buffer larger than one 80-channel sample then I don't have a way to generate an interrupt when one sample has been acquired (which I need, because I'm doing control).
    I saw something in the documentation about a DMA Continue mode in which it looks like you can switch between two different buffers (by programming the Base Count/Address with a different address than the current address) automatically and thereby double-buffer the DMA but there is no real documentation or examples on this capability. However, I think it would work better than the Ring Buffer because I could interrupt on the DMA CONT flag presumably and be copying data out of one buffer while it is filling the other buffer.
    Another option would be DMA chaining, but again, I cannot find any information on these features specific to the NI DAQs.
    I tried interrupting on AI STOP figuring that I could get a single interrupt for each scan, but that doesn't appear to work as expected.
    I know that DAQmx on Windows has the ability to do such single sample, multiple channel tasks at a fixed rate so the hardware must support it.
    Any suggestions would be appreciated.
    Thanks.
    Daniel Madill

    Hello,
    The interrupt that will happen nearest the times that you need is the AI_Start_Interrupt in the Interrupt_A group. This interrupt will occur with each sample clock. By the second time this interrupt fires, the AI FIFO should have the samples from the first conversion. If it is easier to use programmed IO, you can read the samples out of the FIFO until you get all 80.
    Additionally, you can set the DMA to send samples as soon as the FIFO is no longer empty...instead of waiting for half full or full. This change will reduce latency for your control loop. You can set AI_FIFO_Mode in AI_Mode_3_Register to 0. By the second time this interrupt fires, you should be able to check how much data is in the DMA ring buffer and read the 80 samples when they are available. You can make the ring buffer larger than 80 samples if you see data getting overwritten.
    There is no interrupt associated with 80 samples being available in the FIFO or 80 samples being available/transferred by DMA to the host. X Series has much more flexibility with these interrupts.
    I hope this helps!
    Steven T.

  • What is the best mac cleaner and anti virus for mac pro.

    what is the best mac cleaner and anti virus for mac pro.

    OS X already includes everything it needs to protect itself from viruses and malware. Keep it updated with software updates from Apple.
    A much better question is "how should I protect my Mac":
    Never install any product that claims to "speed up", "clean up", "optimize", or "accelerate" your Mac. Without exception, they will do the opposite.
    Never install pirated or "cracked" software, software obtained from dubious websites, or other questionable sources. Illegally obtained software is almost certain to contain malware.
    Don’t supply your password in response to a popup window requesting it, unless you know what it is and the reason your credentials are required.
    Don’t open email attachments from email addresses that you do not recognize, or click links contained in an email:
    Most of these are scams that direct you to fraudulent sites that attempt to convince you to disclose personal information.
    Such "phishing" attempts are the 21st century equivalent of a social exploit that has existed since the dawn of civilization. Don’t fall for it.
    Apple will never ask you to reveal personal information in an email. If you receive an unexpected email from Apple saying your account will be closed unless you take immediate action, just ignore it. If your iTunes or App Store account becomes disabled for valid reasons, you will know when you try to buy something or log in to this support site, and are unable to.
    Don’t install browser extensions unless you understand their purpose. Go to the Safari menu > Preferences > Extensions. If you see any extensions that you do not recognize or understand, simply click the Uninstall button and they will be gone.
    Don’t install Java unless you are certain that you need it:
    Java, a non-Apple product, is a potential vector for malware. If you are required to use Java, be mindful of that possibility.
    Disable Java in Safari > Preferences > Security.
    Despite its name JavaScript is unrelated to Java. No malware can infect your Mac through JavaScript. It’s OK to leave it enabled.
    Block browser popups: Safari menu > Preferences > Security > and check "Block popup windows":
    Popup windows are useful and required for some websites, but popups have devolved to become a common means to deliver targeted advertising that you probably do not want.
    Popups themselves cannot infect your Mac, but many contain resource-hungry code that will slow down Internet browsing.
    If you ever see a popup indicating it detected registry errors, that your Mac is infected with some ick, or that you won some prize, it is 100% fraudulent. Ignore it.
    Ignore hyperventilating popular media outlets that thrive by promoting fear and discord with entertainment products arrogantly presented as "news". Learn what real threats actually exist and how to arm yourself against them:
    The most serious threat to your data security is phishing. To date, most of these attempts have been pathetic and are easily recognized, but that is likely to change in the future as criminals become more clever.
    OS X viruses do not exist, but intentionally malicious or poorly written code, created by either nefarious or inept individuals, is nothing new.
    Never install something without first knowing what it is, what it does, how it works, and how to get rid of it when you don’t want it any more.
    If you elect to use "anti-virus" software, familiarize yourself with its limitations and potential to cause adverse effects, and apply the principle immediately preceding this one.
    Most such utilities will only slow down and destabilize your Mac while they look for viruses that do not exist, conveying no benefit whatsoever - other than to make you "feel good" about security, when you should actually be exercising sound judgment, derived from accurate knowledge, based on verifiable facts.
    Do install updates from Apple as they become available. No one knows more about Macs and how to protect them than the company that builds them.
    Summary: Use common sense and caution when you use your Mac, just like you would in any social context. There is no product, utility, or magic talisman that can protect you from all the evils of mankind.

  • What is the recommended ratio of publish nodes to dispatcher web servers for CQ5.5?

    What is the recommended ratio of publish nodes to dispatcher web servers for CQ5.5?
    We are getting conflicting opinions on this form the field. I realize this is a loaded question. I'd like to see how Adobe presents this opinion. In the past scaling at the webserver level was only loosely tied to the publishing layer. Now it seems as dynamic functionality increases the ratio is getting closer to 1:1.
    Also,I'd like to know in what use cases this load on publisher increases dramatically.

    Hello, this is an evergreen. Just call setPickOnBounds(false) on the CustomHexagon.
    An issue tracking this problem is open here: https://javafx-jira.kenai.com/browse/RT-17024

  • What is the recommended way for persisting JMS messages?

    What is the recommended way for persisting JMS messages?. As per the IMQ admin documentation , using the default built-in persistence type which is through unix flat files is much efficient and faster, compared to the database persistence .
    Tried setting up the jdbc stuff for database persistence on iAS 6.5 . I am getting the following
    error .
    [24/Apr/2002:16:09:20 PDT] [B1060]: Loading persistent data...
    [24/Apr/2002:16:09:21 PDT] Using plugged in persistent store: database connection
    url=jdbc:oracle:thin:@dbatool.mygazoo.com:1521:qa1 brokerid=ias01
    [24/Apr/2002:16:09:23 PDT] [B1039]: Broker "jmqbroker" ready.
    [24/Apr/2002:16:11:56 PDT] ERROR [B4012]: Failed to persist interest
    SystemManager%3ASystemManagerEngine%2BiMQ+Destination%0AgetName%28%29%3A%09%09SM_Response%0AClass%3A%09%09%09com.sun.messaging.Topic%0AgetVERSION%28%29%3A%09%092.0%0AisReadonly%28%29%3A%09%09false%0AgetProperties%28%29%3A%09%7BJMQDestinationName%3DSM_Response%2C+JMQDestinationDescription%3DA+Description+for+the+Destination+Object%7D:
    java.sql.SQLException: ORA-01401: inserted value too large for column
    [24/Apr/2002:16:11:56 PDT] WARNING [B2009]: Creation of consumer SM_Response to destination 1
    failed:com.sun.messaging.jmq.jmsserver.util.BrokerException: Failed to persist interest
    SystemManager%3ASystemManagerEngine%2BiMQ+Destination%0AgetName%28%29%3A%09%09SM_Response%0AClass%3A%09%09%09com.sun.messaging.Topic%0AgetVERSION%28%29%3A%09%092.0%0AisReadonly%28%29%3A%09%09false%0AgetProperties%28%29%3A%09%7BJMQDestinationName%3DSM_Response%2C+JMQDestinationDescription%3DA+Description+for+the+Destination+Object%7D:
    java.sql.SQLException: ORA-01401: inserted value too large for column
    Any thoughts?

    From the output, you are using imq 2.0. In that release
    the key used to persist a durable subscriber in the database
    table has a limit of 100 characters. The output shows that
    your value is:
    SystemManager%3ASystemManagerEngine%2BiMQ+Destination%0AgetName%28%29%3A%09%09SM_Res
    ponse%0AClass%3A%09%09%09com.sun.messaging.Topic%0AgetVERSION%28%29%3A%09%092.0%0Ais
    Readonly%28%29%3A%09%09false%0AgetProperties%28%29%3A%09%7BJMQDestinationName%3DSM_R
    esponse%2C+JMQDestinationDescription%3DA+Description+for+the+Destination+Object%7D:
    which is much longer than 100 characters.
    You might want to shorten the string you use for the
    durable name.
    And yes, the default file-based persistence store is
    more efficient when compared to the plugged-in persistence
    through a database.

  • What is the recommended virus software for my MacBook?

    what is the recommended virus software for my MacBook?

    None, actually, is needed as there are no known viruse affecting OS X.
    Helpful Links Regarding Virus Protection
    An excellent link to read is Tom Reed's Mac Malware Guide.
    Also, visit The XLab FAQs and read Detecting and avoiding malware and spyware.
    If you require anti-virus protection I recommend using ClamXav.

  • What's the recommended setting for "Process memory usage" ("process virtual" in UI) for a 64-bit host on a 64-bit OS?

    Hi gurus
    In resource based throttling, what's the recommended setting for "Process memory usage" ("process virtual" in the resource based throttling tab of the UI) for a 64-bit host
    on a 64-bit Windows OS?
    According to MS (http://msdn.microsoft.com/en-us/library/ee308808(v=bts.10).aspx):
    "By default, the
    Process memory usage throttling threshold is set to 25. If this value is exceeded and the BizTalk process memory usage is more than 300 MB, a throttling condition may occur. On a 32-bit
    server, you can increase the Process memory usage value to 50. On a 64-bit server, you can increase this value to 100. This allows for more memory consumption by the BizTalk process before throttling
    occurs."
    Does this mean that 100 is the recommended setting for a 64-bit host on a 64-bit Windows?
    Thanks
    Michael Brandt Lassen

    Hi Michael,
    Recommended setting is the default setting which is 25 .dot.
    If your situation is abnormal and you see message delivery throttling state to “4” when the following performance counters are high or if you expect any of you integration
    process could have impact on following counters, then you can consider the suggestion by Microsoft. Don’t change the default setting.
    High process memory
    Process memory usage (MB)
    Process memory usage threshold (MB)
    You can see these counters under “BizTalk:MessageAgent”
    You can gauge these performance counter and its maximum values if have done any regression/performance testing in your test servers. If you have seen these counters having
    high values and causing throttling, then you can update the Process memory usage.
    Or unexpectedly you’re process high throughput messages in production which is causing these counters to go high and cause throttling, then up can update the Process memory
    usage.
    The above two cases where I know my expected process usage (by doing performance testing) or suddenly my production server processing has gone high due to unexpected business
    hike (or any reasons) which caused throttling, then do changes to default throttling setting.
    Just changing the default setting without actual reason could have adverse effect where you end up allocating 
    more processing capacities but the actual message processing message usage ever is low means you end up investing in underutilised resources.
    Regards,
    M.R.Ashwin Prabhu
    If this answers your question please mark it accordingly. If this post is helpful, please vote as helpful by clicking the upward arrow mark next to my reply.

Maybe you are looking for