What is the second, third, etc. next-hop address in the route-map set command for?

What is the second, third, etc. next-hop address in the route-map set command for?
route-map TEST_PBR permit 10 match
match ip address 101
router(config-route-map)#set ip next-hop 1.1.1.1 ?
A.B.C.D IP address of next hop

Hi,
You may get your answer in below link
http://www.groupstudy.com/archives/ccielab/200812/msg00999.html
First next-hop will be used unless until that is not unreachable. If first is unreachable, then next one will be used. Since these next-hops are directly connected, router can easily come to know whether they are active or not. In case you want to set some loopback ip as next-hop then you need to use keyword recursive "set ip next-hop recursive"
--Pls dont forget to rate helpful posts--
Regards,
Akash

Similar Messages

  • Network address as the next hop address in ip route statement???

    Hi All,
    I am confused about ip route statements in the following Cisco document.
    Configuring ISDN DDR with Dialer Profiles
    Document ID: 9568
    http://www.cisco.com/warp/public/793/access_dial/ddr_dialer_profile.html
    The statements are;
    ip route 172.22.0.0 255.255.0.0 172.22.80.0
    ip route 172.22.80.0 255.255.255.0 Dialer1
    Why does it use network address as next hop address on the first line?
    And it is a source network address on the second line.
    Please suggest me.
    Thanks a lot,
    Nitass

    When you specify a network address as next hop in a ip route statement, the router does recursive lookup. When it matches a packet for a network other than 172.22.80.0, it will match the router 172.22.0.0 and the route basically says use 172.22.80.0 as the next hop. Now the router looks up the routing table for how to reach 172.22.80.0 and ends up routing via Dialer 1.

  • What is the best home set up for a family to share/use apple products

    Hi, I am relatively new to apple (have an iPad) and having been a PC user for years I was pleasantly surprised with the apple experience and am now trying to work out the best set up for me, my husband and young son as I am buying them both of them apple products this Christmas.  New Mac laptop/ ipad for hubby and then an ipod touch for my son oh and a new mac laptop for me. We are also thinking of moving from Blackberries to iPhones. Yes we seem to be hooked! but i am unsure about the home family set up and how to replace my PC network that I run off an 8TB server.
    In reading the forums I keep seeing people talk about problems they have with two apple IDs and trying to merge them. I have also heard about a family ID allowing us to share apps legally.  I am really nervous of setting us up wrong and then having problems later and hence i am now looking for some advice on how to share as much as we can legally but also make usage practical and not invading each others privacy. thoughts so far:
    Music - I think we are happy to share the same music and access using one ID (we currently don't buy much music from apple but have lots of CDs we share).
    Photos - It would be nice to share photos - as long as my son or husband cannot accidentally delete photos of mine (which is my biggest concern). I currently load all camera photos onto my 8TB storage box as the network owner and my husband has full access to copy any photo to his laptop but can never delete the original copies by accident.
    Apps - If possible i would like us to share these but they are cheap enough these days to separate if really needed. Would be good to share licence for pages etc though
    cloud, contacts, facetime, email -  this is what is making me consider separate IDs or learning how to have multiple users in one apple ID - I do not want to have to share synced contacts with my husband. I have near 300 contacts now through work etc and he will not want them plus i will not want his or him being able to delete mine by mistake. and then for email and facetime, well I want to give him his privacy so I do not receive his messages etc. especially now that we are considering switching to iPhones
    Then last but not least, i don't know the best solution for my son. he is only 7 years old so even though I don't want to pay for things again I don't want him being able to download "just any" app from the purchased icon in Appstore. Also, is there a child friendly setting to prevent him from viewing inappropriate content on the internet?
    Appreciate I have asked a lot of questions here but I am looking for any genuine advice out there. Thank you in advance to any potential advisers.

    Welcome to the Apple Community.
    You don't need to use the same ID on a device for iCloud and iTunes.
    iCloud covers mail, contacts, calendars, reminders, notes, bookmarks, photostream, document syncing etc and for these I recommend you each have your own ID's, this will stop others from having access to and likely more importantly being able to edit or even delete your personal information.
    Someone of Age needs to be responsible for an account, so for younger children you will need to create and be responsible for an account yourself but let the child use it.
    For iTunes you could use a single account so everyone can share music and apps or you could use separate accounts (there are ways to share content between users, Apple provides homesharing to do this).
    When choosing how to proceed with iTunes, it might be worth remembering that someday your children will reach 21 (or whatever age they feel they have become independent) and will likely want their own account, changing accounts later may make it difficult to access previous content.
    Photostream now has shared albums, so you can share just what you want with others. Shared photos using shared albums cannot be deleted by others with different accounts, but if you all shared the same account they could be.
    Facetime and messages can also use an ID independently of each other, iCloud and iTunes. Separate ID's are recommended for these, joint accounts can be problematic.
    iTunes has parental controls for youngsters, however at 7, I suggest you don't reveal the password to him and enter it yourself when he needs to purchase something, otherwise you may receive unexpected bills.

  • What should the moile netword setting be for the Driod maxx

    I just got my Driod Maxx and the mobile network setting are set on global is it OK for it to stay there or should I can it?

    As demmo86rt mentioned and SuzyQ  I run my phones on LTE / CDMA for me I think my phones response to the Network is better in this setting but for some Gloabal will work probably just as Good,  Something I want be made aware of there is new update that has recently came out for the Droid Maxx.. some customers / members on here are having issues with there phone after updating to this Latest update and possibly the one right before it,, My Droid Maxx is running Totally Fine as is with 4.4.4  system Version 21.11.21.obake-maxx.. If you have not updated and have this Version here I posted and your phone is running fine I'd keep it were it's at for a little while any way..
    Hope this helps..

  • What's the best map in india for BlackBerry user?

    I am new to BlackBerry world..in india bb map is not available....so am having difficulty in navigation without any app!!and also tried google map..but they are useless without google play...!so kindly help me in this!!!!

    Customers can't create new folders under the Public branch.  Generally it isn't a huge problem to put your own images into the SAP folders, although keep in mind that they can be delete or overwritten during an upgrade and you might have to replace them or rename them at that point.
    Everytime you create a BSP or Web Dynpro application you basically have a custom Mime folder.  You can always set the logon information for this folder to embed a user name and password into that note.  If you only have static images in this node and not any actually applications then you souldn't run into any licesnsing problems.

  • What is the best free email provider for a small business? E.g gmail or iCloud etc

    What is the best free email provider for a small business? E.g gmail or iCloud etc

    svdmmanta wrote:
    Is there a free anti-virus download for Macs? Do they do the job or do I have to spend money on something better?
    In General 3rd Party AV Software and Cleaning Utilities tend to cause More Issues than they claim to fix...
    They Not Required...
    Mac OS X tends to look after itself.
    See  >  Mac OS X Built in Security  >  http://www.apple.com/osx/what-is/security.html
    More Info Here  >   https://discussions.apple.com/thread/4545776?tstart=0
    And Here  >  Antivirus Discussion
    The Safe Mac  >  http://www.thesafemac.com/mmg/

  • What is the benefit in using OID for names resolution?

    I have been wondering about this for awhile. I have been working on getting this to work in Iplanet along with Pat Lehane ([email protected]), and it works now.
    What are the benefits in using OID for names resolution when you can just use the static tnsnames.ora. Database and database names are not created dynamically and they don't change that often. Would creates a new database every day and has to worry about changing the static tnsnames.ora file. In my environment, we run Oracle applications from a server, so there is only one tnsnames.ora file, on the file server.
    It would appear that using OID would cause extra traffic (LDAP lookups) on your network.
    I would like some opinions from both Oracle and Oracle users. Thanks

    hi,
    A benefit of using OID for names resolution is that it allows you to centralize net8 naming (i.e., tnsnames) information in the same place (OID) where other types of administrative information (about users, enterprise groups, enterprise roles, etc) gets stored. If you are more comfortable using tnsnames.ora files for net8 naming, that is perfectly fine!
    An important reason that Oracle had for providing Net8 naming functionality in OID is that the legacy 'Oracle Names' functionality of Oracle 7 will eventually be desupported. This is discussed in metalink Note #135696.1 on http://metalink.oracle.com .
    Hope this helps.

  • What are the best imovie, mpeg4 settings for making dvds?

    What are the best imovie, mpeg4 settings for making dvds?

    • iMovie'08 to 11
    - Share to Media Browser - AND as Large (or Medium) - HD or other resolutions degrades the final result
    iMovie'08 to 11 are not the tools of choise if quality is important as they all degrade the picture by discarding every second line when going from, Event's to Project's and this can not be mended.
    iMovie HD6 and FinalCut delivers 100% of what any DVD-Authoring program needs.
    • DVD is as standard MAX - intrelaced SD-Video - and can not be any better than this
    • iDVD does only care about TIME / Duration as
    iDVD 08, 09 & 11 has three levels of qualities. (version 7.0.1, 7,0.4 & 7.1.1) and iDVD 6 has the two last ones
    • Professional Quality
    (movies + menus up to 120 min.) - BEST (but not always for short movies e.g. up to 45 minutes in total)
    • Best Performances
    (movies + menus less than 60 min.) - High quality on final DVD (Can be best for short movies)
    • High Quality (in iDVD08 or 09) / Best Quality (in iDVD6)
    (movies + menus up to 120 min.) - slightly lower quality than above
    Menu can take 15 minutes or even more - I use a very simple one with no audio or animation like ”Brushed Metal” in old Themes.
    About double on DL DVDs.
    • iDVD Does Region = Zero (to be played everywhere)
    • Frame rate - DVD can be in two types PAL (25fps) and NTSC (29.97fps)
    If Your material is 30fps then keep to NTSC (29.97fps), if 25fps keep to PAL.
    One can feed iDVD the other frame rate - BUT RESULTING DVD WILL BE BAD
    I use JES_Deinterlacer (free on Internet) to convert all material to the same and final frame rate
    • NTSC - US etc
    • PAL - EU etc
    Yours Bengt W

  • What is the best mac to get for downloading over 30,000 photos?

    what is the best mac to get for downloading over 30,000 photos?

    Download from where into what? What are you going to do with the photos?
    I agree with Larry that a Mac with an SSD boot drive and addtional standard drive is blazingly fast.  I have an iMac setup that way and it boots in 14 seconds.  With the system and applicaitons and iPhoto library on the SSD drive and most other documents, backup photos, etc. on the std. drive. it works beautifully.  However, I do not let the free space on the SSD drive get less than 50 GB.
    I also have an external HD that I sue with Time Maching to backup both my SSD and standard drive in the iMac.
    OT

  • What are the Corresponding fields in CRM for sales order in ECC

    HI! Experts,
    While creating a standard sales order in CRM I want to poulate these fields in ECC Sales order, these fields are
    VBKD-BSARK - Purchase order type
    VBAK-BNAME - Name: user ordered
    VBKD-IHREZ - Web Confirmation Number
    VBAK-TELF1 - Telephone number
    Or the other way round I want to know what are the corresponding fields in CRM for these fields so that when I pass the data in crmd_order in those fields it gets populated in the above mentioned fields.
    Thanks and Regards
    Mayank

    Mayank,
    May I suggest you to create an Order in R/3 with these fields and check that back in CRM. This is not as easy as it may sound. It is possible that some of these fields are "determined" by the system - for example the "Sold-To"'s first telephone number maintained in VBAK-TELF1. So, though it becomes a part of the Order header in R/3, CRM, generally doesn't duplicate them in the transaction but allows to refer back to the master data from the transaction!
    Check the following fields in CRM and see if you find the data you require.
    VBKD-BSARK - Purchase order type There is a field in CRM that "holds" this value. ACTIVITY CATEGORY. This can be found in the ACTIVITY_H set of the transaction. Filed name CATEGORY. Problem with this is, - "Category Type" of a CRM Activity to be mapped to PO type? Didn't workout good for us since the master data for both vary widely. So, we used custom Header Extension data for this (EEWB). So, you have to work
    VBAK-BNAME - Name: user ordered Is usually CREATED_BY in the CRM Order Header (CRMD_ORDERADM_H). But this fills up the VBAK_ERNAM bit not the BNAME.See the next item, that may give a clue if this is related to the next item.
    VBAK-TELF1 - Telephone number is usually "determined". Usually the Sold-To's first telephone number maintained in the Business Partner "Communication" section for that Sold-To.
    VBKD-IHREZ - Web Confirmation Number Actually it is Customer's or vendor's internal reference as per standard use. Looks like your customer is using it for custom purposes. Well, if you maintain the relationship  "Is Correwspondence Recipient for" with the Sold-To partner in CRM, and maintain the details of this Person, then this will be transferred to R/3.
    Hint: Once you have the R/3 order in CRM, try using the Report program (SE38)  CRM_ORDER_READ in CRM. This is a good tool to "dissect and see" and order in CRM. The program needs only the Transaction Number as the input.
    Easwar Ram
    http://www.parxlns.com

  • What are the 3-bit field choices for Hw_Arm_Sel in PCI-6601

    Hi,
    I am programming our own driver to operate the PCI-6601. For our application we need hardware arm option. I know it is possible to use 2 counters for that, but NI-TIO should support also hw_arm. Although it is not explained in the registry document at all, after some tedious check in the DDK examples I found that this bits are located in the Gi counting mode register. I know the position of the HW_enable as well as the position of the 3 bits for pin sellect options. What I do not know is What are the 3-bit field choices for Hw_Arm_Sel . I contacted NI support but got no support. How can NI sell boards and when a customer who is not using LAbview or Measurement Studio or DDK, but is implementing his own driver is then so arrogantly turned down from NI? Also, how can NI publish just part of the registers the board support, and when a customer contacs and asks for some registers get not at all support? I can not foretell the missing registers, and it is pretty unprofessional to document just partly the registers of 660x devices. And on request you got nothing.
    I hope someone from the community know about this Hw_Arm_Sel 3 pin options. Otherwise, there is just an option of error and trial. Or simply throw the board in the garbage.
    Dr. Kirco Arsov
    Solved!
    Go to Solution.

    Hi Kirco,
    I have some more information for you :-)
    I haven't been able to speak to the developer who is the most familiar with TIO programming since he's out of the office, but I have come across his notes from when he was writing support for the DAQmx driver.
    As I described earlier, the HW_Arm_Sel bits don't select a connector I/O pin, but an internal trigger signal. There are seven internal trigger lines, and the HW_Arm_Sel bits map directly to the internal trigger signal: 0b000 - 0b111 map to 0d0 - 0d7. In order to route an I/O pin to an internal trigger, you must also write to a few more registers.
    From what I've read, there are two more register families that need to be programmed: TG_x_LevelEdgeReg and TG_x_CombinationReg, where x is the internal trigger number. In your case, you only need one pin from the I/O connector to be your arm start trigger, so TG_0_LevelEdgeReg and TB_0_CombinationReg will suffice for your application.
    TB_0_LevelEdgeReg :: Offset 0x660
    TG_0_LevelEdgeReg is only 8 bits wide, and maps as follows:
    7..6: EdgeMode
    5..0: LESel
    LESel selects the I/O connector pin to use as the source for the internal trigger signal. 0d0 - 0d39 will select the I/O pin of the same number. NB: behavior for TG_x_LevelEdgeReg is more limited for triggers 1-7, and only a small subset of the I/O pins can be selected for those trigger signals. Trigger 0 can use any I/O pin. Setting these bits to 0d63 forces the trigger source low, and can be used as a way to 'unroute' it when you're finished with your program.
    EdgeMode determines whether the TIO will detect an edge of the incoming signal, or just pass the signal level straight through. When detecting edges, it will latch the signal and generate a single TIMEBASE3 pulse instead. 0b00 sets level mode; 0b01 sets rising edge; 0b10 sets falling edge; 0b11 sets either edge.
    TG_0_CombinationReg :: Offset 0x6A0
    TG_0_CombinationReg is 32 bits wide, and has three fields of interest:
    19..16: CombFunction
    5..4: CombTypeB
    1..0: CombTypeA
    CombTypeA controls which trigger subsystem to use as the source for the trigger signal. Since you're coming from an I/O pin and using the edge/level subsystem, you must set these bits to 0b01.
    CombTypeB is similar to CombTypeA, and although you won't be using trigger B, set it to 0b01 to be safe.
    CombFunction performs a simple logic function on A and B. Since you're only using a single I/O connector, you only need the A output, so set these bits to 0b1100.
    All of the other bits should be set to 0b0.
    Unfortunately, I'm unable to test these statements since my test machine is currently being used for another research project. Please let me know what happens if you decide to test.
    Joe Friedchicken
    NI VirtualBench Application Software
    Get with your fellow hardware users :: [ NI's VirtualBench User Group ]
    Get with your fellow OS users :: [ NI's Linux User Group ] [ NI's OS X User Group ]
    Get with your fellow developers :: [ NI's DAQmx Base User Group ] [ NI's DDK User Group ]
    Senior Software Engineer :: Multifunction Instruments Applications Group
    Software Engineer :: Measurements RLP Group (until Mar 2014)
    Applications Engineer :: High Speed Product Group (until Sep 2008)

  • What are the best books to purchase for pl/sql programming?

    What are the best books to purchase for pl/sql programming?
    I am new to this field and I am looking for the best books to help me in pl/sql programming. Can someone please suggest?
    Thanks

    In my opinion one of the best to start
    Oracle PL/SQL Programming, Third Edition
    Steven Feuerstein

  • What are the best dimensions to allow for iPad 3 Retina for full-page landscape images?

    What are the best dimensions to allow for iPad 3 Retina for full-page landscape images?
    I read an article and cannot find it that said something about trying to make it 2million pixels and JPG to keep it small, but what exactly should the dimensions be that I ultimately import?  Is there some kind of a "density" setting I have to use, as well, when exporting from Photoshop, for example?

    See Optimizing performance in your iBooks Author books
    Density is discussed by Apple in this context as 'dpi'...
    132 - iPad 2
    264 - new iPad
    At the top of this forum there are popular links listed on the right, including image sizing etc. Be sure to study those existing/previous threads on this topic.
    Good luck.
    Ken

  • What is the safest duplicate file cleaner for macbook pro?

    What is the safest duplicate file cleaner for macbook pro?

    Welcome to the Apple Support Communities
    First, use speech recognition. It's installed on OS X, so you don't have to install a third-party app. See > http://support.apple.com/kb/PH11258?viewlocale=en_US

  • What is the best voice control program for macbook pro

    what is the best voice control program for macbook pro?
    i have lost the use of my arms and need full voice control.
    thank you.

    Welcome to the Apple Support Communities
    First, use speech recognition. It's installed on OS X, so you don't have to install a third-party app. See > http://support.apple.com/kb/PH11258?viewlocale=en_US

Maybe you are looking for