What is Variant Configuration!!!

Hi Guyz,
Can anyone please help me with Variant configuration,I got some info from this forum but that is not explaining anything in detail,what,wher,why?when i create a material with KMAT(configurable material),in basic data 2 screen it is asking for Cross plant CM, i don't have a clue what i need to enter in that field,So plz if you can send some info on variant config. that would great.Really appreciate your help,
u can mail me on [email protected]

Hello Mujtaba,
Refer to the following links for a good understanding of variant configuration.
<a href="https://forums.sdn.sap.com/click.jspa?searchID=944477&messageID=2978315">Process</a>
<a href="https://forums.sdn.sap.com/click.jspa?searchID=944477&messageID=2972200">Variant Pricing</a>
<a href="https://forums.sdn.sap.com/click.jspa?searchID=944477&messageID=2918196">General error</a>
Regards,
Gauravjit.
Reward points if the links are helpful

Similar Messages

SD SAP Variant Configuration questions

Hello guys, I'm preparing for an exam and trying to find the answers for the following questions, please help me, I need them as soon as possible, full points will be given to any answer, Thanks all !
- What is variant configuration?
- What is characteristic?
- What is value?
- What is class?
- What is configuration profile?
- What is dependency and what are the types?
- What is a variant table?
- And the transaction codes for the above.

Dear Kevin,
Thease are possible quetions
the possible questions could be
1. What is item category group in VC
2. what is the item category for the material in VC
3. What is meant by class
4.what is meant by Charateristics values
5.how pricing in mapped in variant confi
6.what are setting in material master in variant material
7.can material type FERT can used has variant material(KMAT), if it is then how
8.waht is requiremnt type while doing variant confi
9.what is stragey group you will select in for vaiant material
10.what is meant by object dependency
11.waht arethe dependency types
12.waht is meant by precondition,selection conditions,actions, procedures
Hope this helps you
Prem.

Variant configuration

I have done all the settings for variant configuration. But still I am getting a error while raising sales order (VA01) (ERROR -configuration not possible for material)
now what should i do.

Dear pavan kumar,
Check Delivering plant is maintained or not in sales order.
Regards,
Srikanthraj

Sales Order text for Variant Configuration

Hello
I have researched my issue and also have asked other peers for guidance. I feel that I am really close to getting my issue to work but I am not sure what I am missing, so I am hoping that someone can give me some advice as to what to check please. See below for the description.
My issue is in reference to SD Variant Configuration and is outlined below.
Overview
Main Unit is a radio test set
Test set can have an upgraded software
Example
Model 6015 u2013 standard test set
Model 6015T u2013 Upgraded software test set
Model 6015V u2013 Upgraded Software + test Set
Requirement
Use same Material Number using Variant Configuration for the upgrades
Price is to default to the Upgraded price
NOTE:
Our materials are already established and are set up as material type Finished Goods; ERLA item category; sales order item category is a copy of TAC. I am using a Configurable Material type KMAT, item category 0002 and linking to the FG material item category ERLA in the material master.
I have created the Material Variant (KMAT) in MM01
Created the characteristic in CT04
Created Classification in MM02 for material FG
Created Super BOM for Configurable Material in CS01 and added the upgrades as Alt Bom 2 for upgrade and 3 for Upgrade+. Also added the Alt BOM text
Created Profile of configurable material in CU41
For the Material I added the configurable material to MRP 3 screen in MM02
Created the BOM link in CS40
I simulate the material in CU50. I enter my material; select the icon for configuration, I can see the characteristic Value Assignment nad see my characteristics Description. I go to the value and use the drop down I then see the pop up of all the different values.
I have created Characteristic Reference VCSD_UPDATE_ARKTX with table VCSD_UPDATE and field ARKTX - no values
I have created a characteristic Test_Choice with the 2 values one is Test Upgrade 1 and the other is Test Upgrade 2. Both of these have the description as well.
For Material Text:
I have set up a reference characteristic using 30 character format (named VCSD_UPDATE_ARKTX),
with table name VCSD_UPDATE and field name ARKTX.
Then in the Configuration Profile(CU42) for configurable material, added a procedure(named PR_PRODUCT_DESCRIPTION) to the dependencies which contains code that sets the description
$self.VCSD_UPDATE_ARKTX = ''Test Upgrade 1u201D
If $self.TEST_CHOICE = Test_Upgrade_1,
$self.VCSD_UPDATE_ARKTX = ''Test Upgrade 2u201D
If $self.TEST_CHOICE = Test_Upgrade_2,
When Entering the sales order for Material Number XXXXXX, I receive a pop up that I can select which Alternate BOM (from CS02) I would like. I select my line item and then select the configuration icon at the bottom of the sales order. I see again my characterestics values (the same as CU50) but am unable to select the radio button. Not sure if this part is standard. Still no change in the sales order line item. I have validated that I am using a copy of the standard TAC item category. How does the text change to the correct value? Am I missing a seeting somewhere. Please provide any guidance with this as I have been trying to get this to work for over a month.
Thank you for your time. It is greatly appreciated.

I have figured out that this will work if I go to the standard material (it is not KMAT but it is a FERT material type) and set the flag in the Material Master Basic Data 2 tab that this is a configurable material and not use KMAT material type for a super BOM. The text changes for this scenario so it give me hope.
This is not ideal, as I want to use the Super BOM because there are different variations (non stock items) that I need to pull through on the picking list in order to tell the end user which option needs to be loaded in the standard material. At least I know the text can change on the sales order; but I am still struggling with the use of the super BOM and changing the sales text when there is use of a super bom as you tie that to the MRP 3 screen of the FERT material type. I can set everything up, but the text will not change if I set up the material master this way. Guidance is appreciated.
Example
Material 72433 (FERT)
on sales order I enter 72433, my alternate BOM comes up with different Options. Alternate BOM 1 is standard configuration; My Alternate BOM 2 has Option 3 and 4 while alternate BOM 3 has option 5 and 6. Alternate BOM 2 is a 6015T and Alternate BOM 3 is a 6015V.
I want my sales order to pull through the text of 6015T or 6015V, whichever is chosen. I want my picklist to print out the option that was selected.

Variant configuration u2013 availability check for Configurable material

Hi Guys,
We are doing the variant configuration scenario for one of our client. We are using planning strategy as 25 (sales order with variant configuration).
When we configure the Configurable material at sales order level, we wanted to check the availability check of Configurable for the combination of selected characteristics.
How we can configure it in the system.
Regards,
Shailendra

Hi,
availability check will work as per the checking group you had defined in system.
additionaly you need to put tick in configuration profile for availability check.
checking for material varient is optional, if your bussiness has materail varients you can activate type matching and while configuring the sales order if the values of charactersticks matches system will suggest you the the appropiate varient and you can replace your configurable material in sales order with it.
hope it will help you.
If you need some more information please explain what exactly your are expecting from system during availability check.
Regards
Ritesh
Edited by: R S D on May 28, 2009 7:29 AM

Process order with variant configuration material

Hi,
I create a process order for a material XX.
This material has a BOM with a material that has variant configuration "class type 300" for price configuration.
When I save the process order I get a message saying "There are still characteristics for components to evaluate". I dont want to evaluate this material in my process order.
What can I do to not have this message?
Regards.

Hi all,
Yes, I work with variant configuration. But sales orders are not involved.
What I do is:
1) I create a purchase order for material X (this material belongs to a BOM), this material has variant configuration. I give a value to the characteristics in the PO.
2) I create a process for a material XXX that has a BOM (material X is in the BOM and cannot be removed).
3) When I save the process order the system asks me to evaluate again the characteristics. This is what I dont want it to do.
Any ideas?
Regards.
Eduardo

COPA Report as Per Characterstics in Variant Configuration

Hi,
I need to develop a COPA Report for the characterstics which are created in Variant Configuration. Kindly help me in bringing those Variant configuration characterstics to COPA.
1. How can i add those characterstics in COPA?
2. How can i bring them to COPA?
3. What should i do if the values of those characterstics into COPA?
Kindly Help me ...
Thanks
Kishore

Hi Kishore,
Please have a look at note 1344848 (Derivation of Variant configuration characteristics). This note explains you all the required steps you should take to derive the charachteristics.
I hope it helps.
Best Regards,
Abhisek

Consuming Material Having Variant Configuration

HI
We are using Variant Configuration for our semi finished product and its
batch managed.There are two plants in one plant say A and B. In A plant
we are using Variant configuration.The same material is stock transferred
to plant B and is further processed.
We are creating CIR in plant B. After taking MRP run we are converting
planned order to purchase requisition and subsequently Stock transfer
purchase order on Plant A. When the material is produced in plant A,it is
transferred to plant B on stock transfer order mentioned above. But the
material is against CIR in plant B. We remove the material from CIR
through 411E movement and system keep it as free stock in unrestricted.
Now when i am consuming this material for further processing in
production order of Material getting manufactured system is asking me for
Variant Characteristics.
System should not ask me variant characteristics once it has been removed
from CIR i.e. special stock.
Any Work around avilable.
Regards,
Anand.

Hi Anand,
Finally, I could understand your issue from your CSS message.
In your description, AA is configurable material in both plant A and plant B, BB is not a configurable material in plant B, AA is a component of material BB, so when you produce BB, there will be dependent requirement generated for AA from BB, now you want to use the stock of AA to fullfill the dependent requirement, however, the system will require you to enter the characteristic at that time.
Then where is the stock of AA comes from? I have mentioned this in my previous reply. But as I have mentioned it is not correct to have unristricted stock for the configurable material, therefore, your process to have free stock of AA is not correct.
Another point is that, your process to have configurable material as a component of a non-configurable material is also not proper.
For example, material BB is a Car, material AA is the Door of the Car, your Car is not configurable, but the Door is configurable, you may have green door and red door according to the configuration, but as your car is a firmed material then what's the meaning to have different door, if you want to have different door, then that means you also need to have different color of the car, like green door for green car, red door for red car, then that means your car should be also a configurable material to make you can select the color of the car too.
Or if your Car is a firmed material as green car, then do you think there is any meaning to configure the door of the car? Unless you do want a red door for a green car, but this can also be realized with a configurable car.
So normally, like your situation, you should use multi-level configuration structure to do the production in make to order scenario.
Therefore, still the problem has been described in my previous reply, no matter how you get the stock of AA, the AA is produced with the configured configuration module, so the stock of AA is also with the configuration data, then no matter how you want to consume the stock of AA, system will always ask for the characteristic of the requirement to compare it with the stock configuration to see if they are same.
For example, you are producing your Car, but as far as I can see you should have no place to configure the door in production order, therefore when you try to consume the door, the system will of course need to know which color you want, because if you want red door but there is only stock of green door, then how the system should do in your opinion?
Then finially, the best way of solving your issue is to have material variant for the configurable material, like the door, you may have material variant as green door and red door, if your firmed Car is green car, then you can use green door as the firmed component, if your firmed Car is red car, then you can use red door as the firmed component, also when you do the production, you could simply produce the green door directly without configure the door, because the material variant is a stockable item but the configurable material is not, then your scenario would be very simple and there will no such problem any more.
If you do still want to keep your scenario, but don't want the system requires you enter the charateristics, then you may have to do the modification of the goods movement transaction to disable that, but it may lead to the inconsistency situation, like actually you want red door, but what you have in stock is green door, without that, you may consume the green door stock for the red door requirement, then it will mess up all the following process.
Also as you are doing the goods movement in MM transaction, so if there is user-exit could be used to change this behavior is decided by MM function, however, base on my checking there will be no such user-exit to control this behavior at MM side, because the consequnce is really dangerous for the system operation.
Therefore, I think the best way for you is still adjust your production scenario to make your production standard, then SAP system will accept that standard production scenario under your requirement.
Thanks and regards,
Rachel
Edited by: Rachel Tang on Apr 2, 2010 10:25 AM
Edited by: Rachel Tang on Apr 2, 2010 10:32 AM

PO EDI - How do I exclude a specific variant configuration value

Hello,
When sending POs via EDI we include our variant configuration values (segment E1CUCFG/E1CUVAL). There is one specific variant configuration we don't want to include as it's irrelevant to the vendor and keeps confusing them. We do need to send all the other variant configuration values. What would be the best way to do this?
Thank you,
Michael

Never mind, I found it.
MM06E001 / EXIT_SAPLEINM_013 allows me to modify E1CUVAL.

BAPI/FM in ECC to create a sales order with variant configurable material

Hi all,
I need to create a function module that creates a sales order in ECC with a variant configurable material.
can some one tell me if there is a in built function module or BAPI that i can make use of to create a sales order with variant configurable material in ECC.
Regards,
Jessica Sam

Thanks MxG,
I dont know how to use this BAPI. .Can you suggest me a sample code.
My reqmnt is, i have
Sold to party, ship to party, bill to party , VC config material and all char values that should be populated while creating a sales order.
please help me with what values should i populate in i/p paramters and and how to use this BAPI with some sample code if posible.
Regards,
Jessica.

Using ALE to synchronize Variant Configuration data from Production to Dev

SAP Gurus,
We are trying to move away from opening our production environment every time with need to add new Variant configuration for products.
In order to do so, we need to ensure that our development and staging systems are in line with production LO-VC data. We have been looking at a possible ALE solution but I would like to get other suggestions.
Any thoughts you may have with regards to either pros and cons of ALE, or another solution we may have overlooked. If your clients are transporting Variant Configuration to production, what method are they currently using to ensure data consistency between environments.
Our landscape currently has two production environments for two separate business lines but both use LO-VC therefore we would like to standardize the process.
Thanks and Regards,
Kevin Webb
SAP SD Senior Consultant

Hi Webb,
General its a complex process to transport VC but for system consistency you can:
1. do the changes Manually in each system
2. Use ALE idoc process to transport.
But ALE transport generally used for fresh VC transport, if the VC already present in transporting system, it may cause inconsistency. Hence if you want to transport some changes then I can suggest you to do MANUALLY.
But if you are transporting VC freshly in each system, go for ALE.
try and revert

Implementing Variant configuration with Non-configurable assembly

Hi Gurus!
I have a scenario but don't know how to implement it.
My header material is configurable and has 3 semi-finished components under it. One of the semi-finished component contains a BOM with 2 raw materials, but this component is not configurable. I mean my model has a multi-level BOM but single a single level configuration. I want to implement an assemble-to-order manufacturing process for the header material. The component with 2 BOM items is manufactured in-house and the other semi-finished components are procured externally.
What kind of planning strategy should I use at the header level and should I maintain any special planning strategy for the non-configurable assembly?
I am new to SAP and also to variant configuration. So please give detailed explanation.
I have read the Planning strategies in the link SAP Library - Demand Management (PP-MP-DEM) but it is too confusing to me.
Best Regards,
Thileepan P

Hi Caetano Almeida
Thank you for the links. I got a few more questions after reading that.
1. In order type settlement profile which order should I check? I am creating a sales order (OR) for a configurable material in MTO strategy 25. In that case should I check "SD1 Sales Order MTO Production"? If so, am I looking at the right screen (refer screenshot below) and are the settings correct in my system?
2. As you have mentioned in the other links. Is it fine to make changes in material valuation in OMS2? Have you come across any situation in which this change has led to other inconsistencies?
Thanks and Regards,
Thileepan

Configuration management (LO-CM) used with Variant configuration (LO-VC)

Hi
I am new to SAP, working with Variant configuration (LO-VC).
I wish to enforce configuration management during development of a new Variant configurator.
Would Configuration management (LO-CM) work together with Variant configuration (LO-VC)?
My expectation is that SAP Configuration management (LO-CM) will work similar to solutions like e.g. MsVisualSourceSafe, SubVersion, CVS, IBM/Rational ClearCase etc. in the software development domain.
best regards Henrik

Hi Amber
Thanks a lot for answer, and please apologize my late response.
I am not confused by the term 'configuration', being used in two different meanings.
(1) Variant configuration (VC) is the dicipline of creating product variants by making a set of choises from the characteristics describing the product. A complete and consistent set of choises is a 'configuration'.
(2) Configuration Management in the 'traditional' software development meaning: Software Configuration Management (SCM). E.g. Microsoft VisualSourceSafe, IMB/Rational ClearCase, Subversion etc. are examples of tools used for the kind of SCM I wish to apply to VC models.
My confusion is whether the SAP CM that I can read about in the SAP online help, is similar to traditional SCM, and whether it can be applied to VC models.
I wish to apply SCM to a VC model. All the objects that together make up the VC model may then each exist in various versions (version control). A complete set of the objects (in a given version) make up a configuration of the VC model.
What is achieved is : you can control the development of VC model in just the same way that all serious software is under the control of SCM. This will allow an evolution of the VC model, like e.g. version 1.0 is released in January, then version 1.1 is released in June. A major upgrade of the model may become version 2.0 in December etc. The 'source code' (the objects) of each of the versions can be retrieved at any time from the SCM system. Also with SCM several developers may work on the same VC model at the same time, and merge their individual work into the same model.
This is very different from todays VC model development. In todays VC model development, only one version exists, that is 'todays version'. Any change to the model is released immediately, and you can undo model changes only if you remember what it was like a little while ago.
We do develop and test VC models in one SAP system, and then move them to the production system. This is however still very far from the benefits of SCM.
best regards
Henrik Saugbjerg

User Exit - VA01 / VA02 Sales Order, using Variant Configuration Fields

Hi,
I'm doing a user exit for creating / changing a sales order (VA01/VA02), and in my program I'm trying to use the characteristic values in variant configuration: Extras -> Configuration.
I know there's a whole bunch of data in SAPMV45A, but I can't seem to find what I need. Structure RV45A is the closest I can find, but the characteristic name / value fields appear empty during the execution of the user exit.
Any help would be greatly appreciated.
Thanks!

R u creating your own user exit or using the ones which are available for VA01/VA02?
If you can use existing ones, to get the more details abt them, please have a look at below link.
http://help.sap.com/saphelp_46c/helpdata/en/1c/f62c7dd435d1118b3f0060b03ca329/content.htm
I hope it helps.
Best Regards,
Vibha
*Please mark all the helpful answers

URGENT :What is webdynpro configuration identifier?

Dear Experts,
Can you please let me know what is webdynpro configuration identifier?
I am new to the webdynpro technology and am not sure .
I am involved in an eRecruiting implementation wherein we have to modify the start page to a cutom one which is in Webdynpro ABAP.
To define a custom start page, i have to specify a configuration id ?
Documentation says : "Enter the Web Dynpro configuration identifier (component configuration ID of the start page component) that defines the start page variant."
Please refer the post i had logged in another areafor more details:
e-Recruiting :Webdynpro for ABAP start page modification
Thanks in advance,
Sowmya

Hi Sowmya
There is a concept called Application Configuration in Web Dynpro ABAP
http://help.sap.com/saphelp_nw04s/helpdata/EN/83/61a042f036c46ae10000000a155106/content.htm
You have to create a configuration for the application or pass the existing configuration to the application.
right click the application and choose create/change configuration, which will take you to configuration editor.
you have to pass the created or existing configuration ID to the application, because the application internally uses the configuration
you have to the pass the parameter WDCONFIGURATIONID=<the configuration id name>
i hope it is clear
Abhi

What is Variant Configuration!!!

Similar Messages

Maybe you are looking for