What just happened??? (Macbook running slow & overheating)
So I've been experimenting with some software (a lot of installing/uninstalling), and my macbook went berzerk... It was running really glitchy for couple of days... Especially when trying to play flash content (CPU overloading, really high temp levels etc...)... I tried running third-party disk repair software like tech tool but nothing was "repaired"... But today I rebooted the OS in safe mode and then rebooted back to normal mode... And now everything is magically cured. I know I should just be happy and let it go, but I really want to know what happend, in case something like this happens again...
Thank you!
Cheerz
HI,
*"I tried running third-party disk repair software like tech tool but nothing was "repaired"."*
*Did TechTool report any errors?"*
Boot from your install disk and make sure the hard disk is ok.
Insert Installer disk and Restart, holding down the "C" key until grey Apple appears.
Go to Installer menu (Panther and earlier) or Utilities menu (Tiger and later) and launch Disk Utility.
Select your HDD (manufacturer ID) in the left panel.
Select First Aid in the Main panel.
(Check S.M.A.R.T Status of HDD at the bottom of right panel. It should say: Verified)
Click Repair Disk on the bottom right.
If DU reports disk does not need repairs quit DU and restart.
If DU reports errors Repair again and again until DU reports disk is repaired.
When you are finished with DU, from the Menu Bar, select Utilities/Startup Manager.
Select your start up disk and click Restart
*"Especially when trying to play flash content (CPU overloading, really high temp levels etc...)..."*
If this happens again, try resetting the NVRAM & PRAM. http://support.apple.com/kb/HT1379
Carolyn
Message was edited by: Carolyn Samit
Similar Messages
-
Hi,
A few people have asked this question, my macbook is running very slow and the mouse spinning circle comes up quite a lot. I am unsure of why it is doing this.
I have attached a copy of the EtreCheck I have done on my system.
Can you please have a look and see if you can see if there is anything wrong, as I am unsure of what I am looking at.
Thanks for your help
Problem description:
Macbook running slow
EtreCheck version: 2.0.11 (98)
Report generated 25 November 2014 11:54:22 GMT
Hardware Information: ℹ️
MacBook Pro (13-inch, Late 2011) (Verified)
MacBook Pro - model: MacBookPro8,1
1 2.4 GHz Intel Core i5 CPU: 2-core
4 GB RAM Upgradeable
BANK 0/DIMM0
2 GB DDR3 1333 MHz ok
BANK 1/DIMM0
2 GB DDR3 1333 MHz ok
Bluetooth: Old - Handoff/Airdrop2 not supported
Wireless: en1: 802.11 a/b/g/n
Video Information: ℹ️
Intel HD Graphics 3000 - VRAM: 384 MB
Color LCD 1280 x 800
System Software: ℹ️
OS X 10.10.1 (14B25) - Uptime: 2 days 14:34:42
Disk Information: ℹ️
ST9500325ASG disk0 : (500.11 GB)
S.M.A.R.T. Status: Verified
EFI (disk0s1) <not mounted> : 210 MB
Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
Macintosh HD (disk1) / [Startup]: 498.88 GB (170.58 GB free)
Encrypted AES-XTS Unlocked
Core Storage: disk0s2 499.25 GB Online
MATSHITADVD-R UJ-8A8
USB Information: ℹ️
Apple Computer, Inc. IR Receiver
Apple Inc. FaceTime HD Camera (Built-in)
Apple Inc. BRCM2070 Hub
Apple Inc. Bluetooth USB Host Controller
Apple Inc. Apple Internal Keyboard / Trackpad
Thunderbolt Information: ℹ️
Apple Inc. thunderbolt_bus
Gatekeeper: ℹ️
Mac App Store and identified developers
Kernel Extensions: ℹ️
/Library/Extensions
[not loaded] foo.tap (1.0) Support
[not loaded] foo.tun (1.0) Support
/System/Library/Extensions
[not loaded] com.novatelwireless.driver.3G (2.2.9) Support
[not loaded] com.novatelwireless.driver.DisableAutoInstall (1.2) Support
[not loaded] com.option.driver.OptionMSD (1.11.0) Support
[not loaded] com.seagate.driver.PowSecDriverCore (5.2.3 - SDK 10.4) Support
[not loaded] com.sierrawireless.driver.SierraDIPSupport (1.0.0) Support
[not loaded] com.sierrawireless.driver.SierraFSRSupport (3.0.0 - SDK 10.6) Support
[not loaded] com.sierrawireless.driver.SierraHSRSupport (3.0.0 - SDK 10.6) Support
[not loaded] com.sierrawireless.driver.SierraIPDirect (1.1.5) Support
[not loaded] com.sierrawireless.driver.SierraQMISupport (1.0.1 - SDK 10.6) Support
[loaded] com.sierrawireless.driver.SierraVSP (1.0.0) Support
[not loaded] com.sierrawireless.driver.qmiNetDriver (1.0.3 - SDK 10.6) Support
/System/Library/Extensions/NovatelWireless3G.kext/Contents/PlugIns
[not loaded] com.novatelwireless.driver.3GData (2.2.9) Support
/System/Library/Extensions/Seagate Storage Driver.kext/Contents/PlugIns
[not loaded] com.seagate.driver.PowSecLeafDriver_10_4 (5.2.3 - SDK 10.4) Support
[not loaded] com.seagate.driver.PowSecLeafDriver_10_5 (5.2.3 - SDK 10.5) Support
[not loaded] com.seagate.driver.SeagateDriveIcons (5.2.3 - SDK 10.4) Support
Startup Items: ℹ️
HW_CreateNetwork: Path: /Library/StartupItems/HW_CreateNetwork
HWNetMgr: Path: /Library/StartupItems/HWNetMgr
HWPortDetect: Path: /Library/StartupItems/HWPortDetect
HWPortDetect_driver: Path: /Library/StartupItems/HWPortDetect_driver
StartOuc: Path: /Library/StartupItems/StartOuc
tap: Path: /Library/StartupItems/tap
tun: Path: /Library/StartupItems/tun
Startup items are obsolete and will not work in future versions of OS X
Problem System Launch Agents: ℹ️
[running] com.paragon.NTFS.notify.plist Support
Launch Agents: ℹ️
[running] com.epson.epw.agent.plist Support
[running] com.oracle.java.Java-Updater.plist Support
[loaded] com.paragon.updater.plist Support
[running] com.sierrawireless.SwitchTool.plist Support
[failed] de.novamedia.VodafoneDeviceObserver.plist Support
Launch Daemons: ℹ️
[loaded] com.adobe.fpsaud.plist Support
[loaded] com.microsoft.office.licensing.helper.plist Support
[loaded] com.oracle.java.Helper-Tool.plist Support
[loaded] com.oracle.java.JavaUpdateHelper.plist Support
User Launch Agents: ℹ️
[loaded] com.adobe.ARM.[...].plist Support
[failed] com.facebook.videochat.[redacted].plist Support
[loaded] com.google.keystone.agent.plist Support
[loaded] com.valvesoftware.steamclean.plist Support
User Login Items: ℹ️
Steam Application (/Applications/Steam.app)
iTunesHelper ApplicationHidden (/Applications/iTunes.app/Contents/MacOS/iTunesHelper.app)
VMCStatusMenu UNKNOWN (missing value)
AutoLaunchApp Application (/Applications/3Connect/3Connect.app/Contents/Resources/AutoLaunchApp.app)
uTorrent UNKNOWN (missing value)
AdobeResourceSynchronizer ApplicationHidden (/Applications/Adobe Reader.app/Contents/Support/AdobeResourceSynchronizer.app)
Android File Transfer Agent Application (/Users/[redacted]/Library/Application Support/Google/Android File Transfer/Android File Transfer Agent.app)
LexmarkNetworkServices ApplicationHidden (/Library/Application Support/Lexmark/LexmarkNetworkServices.app)
3500-4500 Series Button Monitor ApplicationHidden (/Library/Application Support/Lexmark/3500-4500 Series Scanner.bundle/Contents/SharedSupport/3500-4500 Series Button Monitor.app)
Internet Plug-ins: ℹ️
FlashPlayer-10.6: Version: 15.0.0.223 - SDK 10.6 Support
QuickTime Plugin: Version: 7.7.3
AdobePDFViewerNPAPI: Version: 10.1.12 Support
AdobePDFViewer: Version: 10.1.12 Support
Flash Player: Version: 15.0.0.223 - SDK 10.6 Mismatch! Adobe recommends 15.0.0.239
Default Browser: Version: 600 - SDK 10.10
SharePointBrowserPlugin: Version: 14.4.6 - SDK 10.6 Support
Silverlight: Version: 5.1.30514.0 - SDK 10.6 Support
JavaAppletPlugin: Version: Java 7 Update 51 Check version
3rd Party Preference Panes: ℹ️
Flash Player Support
Java Support
Paragon NTFS for Mac ® OS X Support
Time Machine: ℹ️
Skip System Files: NO
Mobile backups: ON
Auto backup: YES
Volumes being backed up:
Macintosh HD: Disk size: 498.88 GB Disk used: 328.30 GB
Destinations:
Seagate Backup Plus Drive [Local]
Total size: 0 B
Total number of backups: 0
Oldest backup: -
Last backup: -
Size of backup disk: Too small
Backup size 0 B < (Disk used 328.30 GB X 3)
Seagate Backup Plus Drive [Local]
Total size: 1.00 TB
Total number of backups: 10
Oldest backup: 2013-05-29 18:19:48 +0000
Last backup: 2013-12-03 06:32:04 +0000
Size of backup disk: Adequate
Backup size 1.00 TB > (Disk used 328.30 GB X 3)
Top Processes by CPU: ℹ️
23% firefox
8% WindowServer
2% hidd
2% mds_stores
1% com.apple.WebKit.WebContent
Top Processes by Memory: ℹ️
387 MB firefox
180 MB com.apple.WebKit.WebContent
146 MB com.apple.MediaLibraryService
125 MB Finder
107 MB iTunes
Virtual Memory Information: ℹ️
48 MB Free RAM
1.60 GB Active RAM
1.53 GB Inactive RAM
1.04 GB Wired RAM
5.95 GB Page-ins
63 MB Page-outsEither update or remove the Vodafone software and see whether there's an improvement.
Any third-party software that doesn't install by drag-and-drop into the Applications folder, and uninstall by drag-and-drop to the Trash, is a system modification.
Whenever you remove system modifications, they must be removed completely, and the only way to do that is to use the uninstallation tool, if any, provided by the developers, or to follow their instructions. If the software has been incompletely removed, you may have to re-download or even reinstall it in order to finish the job.
I never install system modifications myself, and except as stated in this comment, I don't know how to uninstall them. You'll have to do your own research to find that information.
Here are some general guidelines to get you started. Suppose you want to remove something called “BrickMyMac” (a hypothetical example.) First, consult the product's Help menu, if there is one, for instructions. Finding none there, look on the developer's website, say www.brickmymac.com. (That may not be the actual name of the site; if necessary, search the Web for the product name.) If you don’t find anything on the website or in your search, contact the developer. While you're waiting for a response, download BrickMyMac.dmg and open it. There may be an application in there such as “Uninstall BrickMyMac.” If not, open “BrickMyMac.pkg” and look for an Uninstall button. The uninstaller might also be accessed by clicking the Customize button, if there is one.
Back up all data before making any changes.
You will generally have to restart the computer in order to complete an uninstallation. Until you do that, there may be no effect, or unpredictable effects.
If you can’t remove software in any other way, you’ll have to erase and install OS X. Never install any third-party software unless you're sure you know how to uninstall it; otherwise you may create problems that are very hard to solve.
Trying to remove complex system modifications by hunting for files by name often will not work and may make the problem worse. The same goes for "utilities" such as "AppCleaner" and the like that purport to remove software. -
Hi everyone,
My macbook has been running slow for a little while, and by slow I mean taking forever to load applications, files etc and not being able to run too many things at once. It also gets hot quite quickly.
I know I can upgrade the RAM, but I was just wondering IF that will fix my problem before I go and spend that money on something that may not work.
Advice is appreciated!
Problem description:
Macbook running slow
EtreCheck version: 2.1.8 (121)
Report generated 3 March 2015 8:26:42 pm AEST
Download EtreCheck from http://etresoft.com/etrecheck
Click the [Click for support] links for help with non-Apple products.
Click the [Click for details] links for more information about that line.
Hardware Information: ℹ️
MacBook (13-inch, Mid 2010) (Technical Specifications)
MacBook - model: MacBook7,1
1 2.4 GHz Intel Core 2 Duo CPU: 2-core
2 GB RAM Upgradeable
BANK 0/DIMM0
1 GB DDR3 1067 MHz ok
BANK 1/DIMM0
1 GB DDR3 1067 MHz ok
Bluetooth: Old - Handoff/Airdrop2 not supported
Wireless: en1: 802.11 a/b/g/n
Battery Health: Normal - Cycle count 567
Video Information: ℹ️
NVIDIA GeForce 320M - VRAM: 256 MB
Color LCD 1280 x 800
System Software: ℹ️
OS X 10.9.5 (13F34) - Time since boot: 0:53:39
Disk Information: ℹ️
Hitachi HTS545025B9SA02 disk0 : (250.06 GB)
EFI (disk0s1) <not mounted> : 210 MB
Untitled (disk0s2) / : 249.20 GB (80.06 GB free)
Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
HL-DT-ST DVDRW GS23N
USB Information: ℹ️
Apple Inc. Built-in iSight
Apple Inc. BRCM2070 Hub
Apple Inc. Bluetooth USB Host Controller
Apple Inc. Apple Internal Keyboard / Trackpad
Gatekeeper: ℹ️
Mac App Store and identified developers
Kernel Extensions: ℹ️
/Library/Application Support/Roxio
[not loaded] com.roxio.TDIXController (1.7) [Click for support]
/System/Library/Extensions
[not loaded] at.obdev.nke.LittleSnitch (3932 - SDK 10.8) [Click for support]
[not loaded] com.ZTE.driver.ZTEUSBCDCACMData (1.3.12) [Click for support]
[not loaded] com.ZTE.driver.ZTEUSBMassStorageFilter (1.3.12) [Click for support]
[not loaded] com.cisco.nke.ipsec (2.0.1) [Click for support]
[loaded] com.dvdfab.kext.fabio (1) [Click for support]
[not loaded] com.option.driver.Option72 (2.17.0) [Click for support]
[not loaded] com.option.driver.OptionMSD (1.21.0) [Click for support]
[not loaded] com.seagate.driver.PowSecDriverCore (5.0.1) [Click for support]
[not loaded] com.sierrawireless.driver.SierraDIPSupport (1.0.0) [Click for support]
[not loaded] com.sierrawireless.driver.SierraDevSupport (1.0.7) [Click for support]
[not loaded] com.sierrawireless.driver.SierraFSRSupport (3.0.0) [Click for support]
[not loaded] com.sierrawireless.driver.SierraHSRSupport (3.0.0) [Click for support]
[not loaded] com.sierrawireless.driver.SierraIPDirect (1.1.4) [Click for support]
[not loaded] net.Thomson.iokit.USBLAN_usbpart (1.6.0) [Click for support]
/System/Library/Extensions/Seagate Storage Driver.kext/Contents/PlugIns
[not loaded] com.seagate.driver.PowSecLeafDriver_10_4 (5.0.1) [Click for support]
[not loaded] com.seagate.driver.PowSecLeafDriver_10_5 (5.0.1) [Click for support]
[not loaded] com.seagate.driver.SeagateDriveIcons (5.0.1) [Click for support]
Problem System Launch Agents: ℹ️
[failed] com.paragon.NTFS.notify.plist [Click for support]
Launch Agents: ℹ️
[running] com.brother.LOGINserver.plist [Click for support]
[running] com.seagate.SeagateStorageGauge.plist [Click for support]
Launch Daemons: ℹ️
[loaded] com.adobe.fpsaud.plist [Click for support]
[loaded] com.microsoft.office.licensing.helper.plist [Click for support]
[loaded] com.sierrawireless.SWoCTool.plist [Click for support]
User Launch Agents: ℹ️
[loaded] com.adobe.ARM.[...].plist [Click for support]
[failed] com.apple.CSConfigDotMacCert-[...]@me.com-SharedServices.Agent.plist [Click for details]
[running] com.google.Chrome.framework.plist [Click for support]
[loaded] com.google.keystone.agent.plist [Click for support]
[running] com.spotify.webhelper.plist [Click for support]
User Login Items: ℹ️
Flux Application (/Applications/Flux.app)
Flux Application (/Applications/Flux.app)
Flux UNKNOWN (missing value)
Caffeine Application (/Applications/Caffeine.app)
Google Chrome Application Hidden (/Applications/Google Chrome.app)
StatusMenu UNKNOWN (missing value)
Internet Plug-ins: ℹ️
JavaAppletPlugin: Version: Java 8 Update 25 Check version
FlashPlayer-10.6: Version: 15.0.0.152 - SDK 10.6 [Click for support]
Default Browser: Version: 537 - SDK 10.9
AdobePDFViewerNPAPI: Version: 10.1.13 [Click for support]
AdobePDFViewer: Version: 10.1.13 [Click for support]
Flash Player: Version: 15.0.0.152 - SDK 10.6 Outdated! Update
QuickTime Plugin: Version: 7.7.3
SharePointBrowserPlugin: Version: 14.1.2 [Click for support]
Unity Web Player: Version: UnityPlayer version 3.3.0f4 [Click for support]
Silverlight: Version: 4.1.10329.0 [Click for support]
iPhotoPhotocast: Version: 7.0 - SDK 10.8
3rd Party Preference Panes: ℹ️
Flash Player [Click for support]
Time Machine: ℹ️
Skip System Files: NO
Auto backup: NO - Auto backup turned off
Destinations:
Backup [Local]
Total size: 0 B
Total number of backups: 0
Oldest backup: -
Last backup: -
Size of backup disk: Excellent
Backup size 0 B > (Disk size 0 B X 3)
Top Processes by CPU: ℹ️
5% WindowServer
4% Safari
2% hidd
2% com.apple.WebKit.Networking
0% ocspd
Top Processes by Memory: ℹ️
112 MB Safari
43 MB Finder
30 MB com.apple.WebKit.WebContent
28 MB com.apple.WebKit.Networking
26 MB Google Chrome
Virtual Memory Information: ℹ️
15 MB Free RAM
597 MB Active RAM
583 MB Inactive RAM
330 MB Wired RAM
1.10 GB Page-ins
59 MB Page-outs
Diagnostics Information: ℹ️
Mar 3, 2015, 07:29:45 PM Self test - passedHi Mike,
Thanks for your help. I've ordered 8gb of RAM and cleared up some of the software and extensions. Hopefully this helps it run a little faster.
Thanks again! -
Please tell me what just happened...
OK. Here is what just went down when I went into a corporate AT&T Store:
1. I told the sales guy that I just purchased a 3G iPhone on June 3rd online, and would like to pay the 10% restocking fee and get a new 3GS.
2. He said that would be fine and started messing on the computer and said he took the phone off my account and opted me back out of my 2 year contract I renewed.
3. The manager then came over and said they cannot issue refunds from online purchases and I need to mail it back to AT&T.
4. The sales guy then let me pre-order the iPhone 32GB 3GS iphone for $299 and said he had to keep my 3G iphone until I pick up my 3GS next friday, unless I wanted to come by sooner and "tell them how to return it to AT&T".
5. He gave me my sim card out of my phone so I could use it on a backup phone I have at home.
6. Now I am home, and AT&T website is telling me I am eligible for an upgrade (although I just upgraded at the store).
Am I officially upgraded? If I order one online get I get the one next friday in the store AND in the mail and have 2, activate 1, and sell the other one on the side? If someone has any idea what just happened please let me know.
ThanksDoes View > Zoom > Reset help to get a normal font size?
* http://kb.mozillazine.org/Zoom_text_of_web_pages -
I accidentaly pressed on "forget this devise" in the bluetooth settings. Now my iPhone would not even list my headset. How can I reverse what just happened and connect my headset? Can anyone assit please?
You need to put the headset into pairing mode. The phone should then see it even though you have done the forget this device.
-
I have macbook pro running Intel Core 2 Duo if I upgrade to Lion OS Xv10.7 will my macbook run slower?
I have a 13" MBP with the Core 2 Duo processor. I do have 8 GB of memory, needed because I need to run Windows in a virtual machine (Fusion) to access client web sites that require ActiveX controls. The Windows VM environment locks up 3 GB of the memory.
I did all the maintenance steps in disk utility on the harddrive before upgrade, double checked compatability with all applications and drivers and made sure that I had a drive clone in addition to my Time Capsule backup.
The only thing that didn't work on Lion was my RingCentral VOIP client, and that was expected from my research.
The upgrade went smooth and I really haven't noticed much speed difference. -
My MacBook runs slow. Tried "Safe Mode", not very clear effect to improve. Anyone has better idea? Thanks!
Its a possibility there is hardware issues,
or even adware. Bring your MB into a licensed store and run a diagnostic!
OR
(AT YOUR OWN RISK)
Run a program called adware medic http://www.adwaremedic.com/index.php
It will detect anything that shouldn't be there.
You can also put your ear up to the location of the HDD (right bottom where you right hand rests) and listen if the HDD is making any strange noises or repetitive clicking. -
I was working on a project and all of a sudden everything with in PS got noteably slow and choppy. This first happened while using the selection tool (polygonal lasso), which was lagging behind and making late clicks. I finished my selection and noticed the cursor in general was slow choppy still. I saved my work, shutdown PS, then reboot my computer. I reopen my project, the cursor lag seemed to be gone but the brush tool was not working correctly. Instead of making smooth burst of color with one click (gradient like), it now looks like 256 4 bit (old nintendo style) bursts. Or you could say it looks like multiple rings getting smaller and darker, like counting the rings of a tree trunk.
This happens instantly after opening a file of any type and size. I work with CMYK and 300dpi and while working on a page, this just happened out of nowhere.
I have an ASUS G74SX, i7 CPU, GeForce 560M w/2 gig RAM, 8 gig of SDRAM, 3 each SSD 300gigs (this is basically a 6 month old gaming laptop and has been working fine with PS until now). I have my PS scratch disk set to my F drive for all art and there is nothing more than 2 gigs of space being used right now. My RAM used in PS prefs was maxed at 5205k as suggested by the program.
I would post a picture but this forum will not allow a big enough image to show exactly what I am describing.
PS CS6 is fully up to date as well as all drivers for my GPU and the rest of my laptop.
Thanks
JoshI personally like to Crop, and then use PNG for my screen-caps. If I need more images, say to show other Palettes, etc., then I do one each for those shots.
We see a lot of full-screen caps posted, where aggressive JPEG is used, and nothing can be read. That is especially true with images, like Adobe Encore's Flow-chart, where there is a lot of text and linking being shown.
Just my personal preferences.
Hunt -
I just purchased a new Macbook this month. I transferred everything from my old computer (a powerbook) to my new one and it seems like everything on the new computer is running more slowly than it should. For example, it takes a few minutes for the computer to open programs, like adobe acrobat reader or word. I get the spinning rainbow pinwheel a lot when the computer encounters new documents or applications to open. The other day, I downloaded a 2 page PDF document and it took the computer more than 3 full minutes or spinning pinwheel to open acrobat and the document. It doens't just happen with acrobat, it happens with most programs. Once the programs are open, they seem to run okay. I am planning to upgrade the ram (I have 512 right now), but even without the upgrade, this computer is running very slowly. I had the same problem with my old powerbook towards the end, but I assumed it was the aging computer. Is there anything I can check, as far as the software or setup in my new computer that could fix this problem? I think maybe whatever was slowing down my old computer was transferred to my new computer and is causing the same issue. I'm not sure where to start, as far as troubleshooting it and figuring out what's wrong. Any advice is appreciated. Thanks.
Macbook Mac OS X (10.4.7)The apps you mention -- Adobe Reader and MS Word -- are not Intel-native. So they run in the emulation layer called Rosetta. That makes them slow.
Try using Preview to open PDFs.
Adding more RAM will help some, because Rosetta itself needs RAM in addition to the application it's running. But the ultimate solution is for Adobe and Microsoft to release Intel versions of their apps. This should happen sometime in 2007. -
Why is my new macbook running slow?
I've had this computer since August 2012 and now it's suddently starting to run slow. The spinning wheel keeps appearing evertime I use the computer. I tired shuting down and restarting the thing but it still acts the same. It pops up every few seconds and it's frustrating. I also tried deleting history and other things to make the computer work faster but nothing seems to work.
This all started happening on Saturday. It was working fine since then. I don't know what's the problem. Simply just clicking on anything now is a hassel.I am also so dsappointed of buying macbook pro for the first time,and to think it was just almost a month ago....I am worried about the over heating issue,battery span that never lasprot that long as what the advertisement says...I really take extra care of this gadget because it is my first time having this so expenssive lappy...Ooohhh before I forget,my gadget is Macbook Pro 13 with memory of 8gb 1600 MHz DDR3..processor 2.9GHz Intel core I7...the only heave application tha I downloaded was the Mountain Lion I think ,and it was updated now from 10.8.1 - 10.8.2 ..maybe the next heavy app is the google chrome...and the rest is those apps that I bought from the Apple store that didnt cost me $10...before buying this unit ,I am using a lappy from Gateway with windows OS that runs slowly because of maybe being so old...lol I am using it for almost 3yrs because I only bought it from a junk shop alternately with Dell desktop thats so cheap,I only bought it almost $200 from a junkshop still.now after learning to fix and upgrade computers,I upgraded the DELL desktop from 1GB to 2GB,but I upraded my hardrive from 80gb to 1000gb...now I did test booting the 2,the desktop and this new Macbook Pro.my dell really boot so fast half more than this macbook pro...when I am downloading videos,really the Dell desktop have the fastest loading and downloading...I am not kidding and telling lies...I am so shock to know the real truth....I am sorry, but i is really true...But I promise my self to take care of this gadget because its my first time to have a genuinely brand new gadget and so expenssive...if no one believe this, i will upload a video on my youtube accnt just to prove that I am not telling a lie...oooh before I forget...just to prove that this gadget is geguine and new, here is the Serial Number of my Macbook Pro 13 which I posses almost a month now.. Serial Number C0******DTY4
<Edited by Host> -
My wife has a 2009 Macbook, today it would turn on for a moment and start to load then just shut off. I reset the SMC by pressing the left shift+control+option and power button. Didnt work on the first try but the second time it did. So i have the computer on now but it has been running slow lately and I am not sure why. We did a virus scan and nothing, she has the memory clean program that she uses to clean her memory, also updated her software to mountain lion, but I dont know what else to do. Any advice on how I may speed her computer back up?
Upgrading a machine does not speed it up, except maybe upgrading the RAM. See my FAQ*: http://www.macmaps.com/badram.html
-
MacBook running slow after installing Snow Leopard
I have 1 Gb of memory & MacBook is running slow after I installed Snow Leopard. Would it help to add more memory?
R C-R wrote:
No, inactive memory is just that: memory not actively used by anything. Paged out memory is a chunk of memory that has been swapped out to the hard drive. It must be paged back into memory if its contents are needed for anything. "Paged" refers to the amount of memory swapped in & out at a time, since the OS does this in units of memory called "pages."
This is the simplified, executive summary version. For all the gory details, see Mac Dev Center: Memory Usage Performance Guidelines: Memory Management in Mac OS X.
Thanks much. I know that it is not being used by anything currently. But, does it contain what I mentioned above, or is there a better description for what is in inactive memory? And, were does it go when replaced by something else? Paged to swapfiles?
Edit: Go to go now. Will check in later. And, I will read the memory link provided.
Message was edited by: donv (The Ghost) -
Why is my macbook running slower after loading OSX mountain lion?
Just downloaded OSX Mountain Lion a few weeks ago and my laptop seems to be running slower - delayed window filling, etc. Anyone else notice this problem or have any solutions? Should I just go in to see a genius?
TIA,
ddhallFirst, back up all data immediately, as your boot drive might be failing.
One possible cause of a slow user interface is a large number of image or video files on the Desktop with preview icons. If you have more than a dozen or so such files, move them to another folder.
Otherwise, take these steps when you notice the slowdown.
Step 1
Launch the Activity Monitor application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Activity Monitor in the icon grid.
Select the CPU tab of the Activity Monitor window.
Select All Processes from the menu in the toolbar, if not already selected.
Click the heading of the % CPU column in the process table to sort the entries by CPU usage. You may have to click it twice to get the highest value at the top. What is it, and what is the process? Also post the values for % User, % System, and % Idle at the bottom of the window.
Select the System Memory tab. What values are shown in the bottom part of the window for Page outs and Swap used?
Next, select the Disk Activity tab. Post the approximate values shown for Reads in/sec and Writes out/sec (not Reads in and Writes out.)
Step 2
If you have more than one user account, you must be logged in as an administrator to carry out this step.
Launch the Console application in the same way you launched Activity Monitor. Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left.
Select the 50 or so most recent messages in the log. Copy them (command-C) to the Clipboard. Paste (command-V) into a reply to this message.
When posting a log extract, be selective. Don't post more than is requested.
Please do not indiscriminately dump thousands of lines from the log into this discussion.
Important: Some personal information, such as your name, may appear in the log. Anonymize before posting. -
Macbook running slow after mountian lion install??
i have a late 2010 macbook (white) and i recently upgraded my mac to mountian lion after ugrading to 4 GB of RAM. i tried the vram and pram reset but that was a couple months ago. maybe i should try it again? what else do i need to do?
it takes 1:30 mins boot up
45 - 50 sec to log in.
all of my app take for ever to open.
trackpad is extremely sensitive.
safari is slow and wasnt before
any help or suggestions would be greatly appreciated!Things You Can Do To Resolve Slow Downs
If your computer seems to be running slower here are some things you can do:
Start with a visit to: OS X Maintenance - MacAttorney.
Boot into Safe Mode then repair your hard drive and permissions:
Repair the Hard Drive and Permissions Pre-Lion/Mountain Lion
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
Repair the Hard Drive - Lion/Mountain Lion
Boot from your Lion Recovery HD. When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported, then click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu. Select Restart from the Apple menu.
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Restart your computer normally and see if this has helped any. Next do some maintenance:
Suggestions for OS X Maintenance
For situations Disk Utility cannot handle the best third-party utility is Disk Warrior; DW only fixes problems with the disk directory, but most disk problems are caused by directory corruption; Disk Warrior 4.x is now Intel Mac compatible.
OS X performs certain maintenance functions that are scheduled to occur on a daily, weekly, or monthly period. The maintenance scripts run in the early AM only if the computer is turned on 24/7 (no sleep.) If this isn't the case, then an excellent solution is to download and install a shareware utility such as Macaroni, JAW PseudoAnacron, or Anacron that will automate the maintenance activity regardless of whether the computer is turned off or asleep. Dependence upon third-party utilities to run the periodic maintenance scripts was significantly reduced since Tiger. These utilities have limited or no functionality with Snow Leopard or Lion and should not be installed.
OS X automatically defragments files less than 20 MBs in size, so unless you have a disk full of very large files there's little need for defragmenting the hard drive. As for virus protection there are few if any such animals affecting OS X. You can protect the computer easily using the freeware Open Source virus protection software ClamXAV. Personally I would avoid most commercial anti-virus software because of their potential for causing problems. For more about malware see Macintosh Virus Guide.
I would also recommend downloading a utility such as TinkerTool System, OnyX 2.4.3, or Cocktail 5.1.1 that you can use for periodic maintenance such as removing old log files and archives, clearing caches, etc.
For emergency repairs install the freeware utility Applejack. If you cannot start up in OS X, you may be able to start in single-user mode from which you can run Applejack to do a whole set of repair and maintenance routines from the command line. Note that AppleJack 1.5 is required for Leopard. AppleJack 1.6 is compatible with Snow Leopard. There is no confirmation that this version also works with Lion.
When you install any new system software or updates be sure to repair the hard drive and permissions beforehand.
Get an external Firewire drive at least equal in size to the internal hard drive and make (and maintain) a bootable clone/backup. You can make a bootable clone using the Restore option of Disk Utility. You can also make and maintain clones with good backup software. My personal recommendations are (order is not significant):
1. Carbon Copy Cloner
2. Data Backup
3. Deja Vu
4. SuperDuper!
5. SyncTwoFolders
6. Synk Pro
7. Synk Standard
8. Tri-Backup
Visit The XLab FAQs and read the FAQs on maintenance, optimization, virus protection, and backup and restore.
Additional suggestions will be found in Mac maintenance Quick Assist.
Referenced software can be found at CNet Downloads or MacUpdate.
Additional Hints
Be sure you have an adequate amount of RAM installed for the number of applications you run concurrently. Be sure you leave a minimum of 10% of the hard drive's capacity as free space.
Add more RAM. If your computer has less than 2 GBs of RAM and you are using OS X Leopard or later, then you can do with more RAM. Snow Leopard and Lion work much better with 4 GBs of RAM than their system minimums. The more concurrent applications you tend to use the more RAM you should have.
Always maintain at least 15 GBs or 10% of your hard drive's capacity as free space, whichever is greater. OS X is frequently accessing your hard drive, so providing adequate free space will keep things from slowing down.
Check for applications that may be hogging the CPU:
Open Activity Monitor in the Utilities folder. Select All Processes from the Processes dropdown menu. Click twice on the CPU% column header to display in descending order. If you find a process using a large amount of CPU time, then select the process and click on the Quit icon in the toolbar. Click on the Force Quit button to kill the process. See if that helps. Be sure to note the name of the runaway process so you can track down the cause of the problem.
Often this problem occurs because of a corrupted cache or preferences file or an attempt to write to a corrupted log file. -
I have a late 2011 macbook 2.7 GHz i7. This wasn't a gradual thing, it just happened all of a sudden. I had upgraded to mountain lion of which I de-fragged my hard-drive thinking it was a hard drive issue, and am now running snow leopard but it hasn't made a difference. Is there like a energy saving option I am unaware of?? Please help, its driving me crazy. Its making my mac literally useless.
Use Onyx (free) to do a system cleanup (cache cleanup, permissions repair, etc.).
Maybe you are looking for
-
Can we restrict the printing of PO Item text based on PO types?
Dear Experts, We have a requirement related to printing of PO Item Text. We need to print a perticular Item text only for a certaing PO type (ex: NB only). How can we restrict the printing of PO Item text based on PO types? Please advise. Regards,
-
How do I connect speakers to my Mac Mini
I am a new Mac user switching from a PC and I am wondering if there is a way to connect my 5.1 surround sound system to the Mac Mini?
-
Issue with activation of 0FISCPER
Hi Friends, I have an issue with activation of 0FISCPER.Based on this link i went uncheck the hirearchiel tab 0CALMONTH and 0FISCPER Not active in BW Production and i am trying to activating it is saying already exist transformations it is going to d
-
Using airport express as range extender?
I have a airport express that I use as my primary router. I also have the direct plug in airport express that I'd like to use as a range extender. I'd like to make this one fully wireless so that I can connect in an another room. However, I'm not sur
-
Column formatting based on grouping data value- advanced data grid
Hello Everyone, I am using advanced data grid to display hierarchial data nested upto depth 4. I have to color the leaf nodes conditionally based on the grouped column value. Say for Eg., If the data is something like Company Manager