What kind of card should I use with my DAQ setup?

We are using the e-series multifunction DAQ PCI-MIO-16XE-10 and are looking for a good DAQcard to go with it. We are wondering if there is a DAQcard with 16 bit analog output and higher than 20 kS/s.

National Instruments currently doesn't have a 16-bit analog output PCMCIA card. There is a 16-bit analog input card, however. For those customers interested, I am referring to the DAQCard-AI-16XE-50.
If speed is critical, you might still consider the 12-bit DAQCard-6062E. It has a single-channel analog output rate of 850 kS/sec.

Similar Messages

What XA JDBC driver should I use with Oracle 8i 8.1.6

I need to use an XA JDBC driver for Oracle 8i 8.1.6. I am using the driver in
a ConnectionPool in a TxDataSource for use by some entity beans using EJB 2.0.
I'm running WebLogic Server 6.0 sp2, EJB 2.0, Java 2 SDK 1.3.1 Server VM, Solaris
2.7, and Oracle 8i 8.1.6.
I know of three different Oracle XA drivers: WebLogic jDriver for Oracle XA, Oracle
OCI type 2 driver XA, and Oracle Thin tyoe 2 XA. Are there any other drivers
that I can use for Oracle 8.1.6? Which driver and which version should I use?
For example, can I use the Oracle 8.1.7 JDBC drivers with the Oracle 8.1.6 server,
or would the Oracle 9i drivers work with the Oracle 8i server? Which drivers
are faster, and which support more features? I assume that I should not use the
type 4 driver since I am not using an applet, but I don't know if there are bugs
in the OCI C library for Solaris or in the JDBC drivers that use it that prevent
XA from woking. Which version of the Oracle C OCI library should I use if I use
a type 2 driver?
Thanks,
Ross Goldberg

Hi,
I think you can't use the 8.1.6 thin driver for XA, you would have to
use the OCI driver or 2PC-enable your datasource. AFAIK this has been
changed for 8.1.7
Check http://e-docs.bea.com/wls/docs61/////jta/thirdpartytx.html.
Daniel
-----Original Message-----
From: Gene Chuang [mailto:[email protected]]
Posted At: Thursday, August 30, 2001 2:04 AM
Posted To: jdbc
Conversation: What XA JDBC driver should I use with Oracle 8i 8.1.6
Subject: Re: What XA JDBC driver should I use with Oracle 8i 8.1.6
I've asked this question before. This is the reply from Joe
Weinstein:
For reliability and JDBC 2.0 compliance, I recommend the
Oracle thin driver.
If not that driver, you should verify that a type-2 driver
actually does
deliver better performance, but then I would not have a
strong preference
between their type-2 and ours. Theirs may be faster, and JDBC
2.0 compliant.
Both are succeptible to OCI bugs, some of which only they can
fix, but we
listen.
Gene
"Ross Goldberg" <[email protected]> wrote in message
news:[email protected]...
>
I need to use an XA JDBC driver for Oracle 8i 8.1.6. I am using thedriver in
a ConnectionPool in a TxDataSource for use by some entity beans usingEJB 2.0.
I'm running WebLogic Server 6.0 sp2, EJB 2.0, Java 2 SDK 1.3.1 ServerVM, Solaris
2.7, and Oracle 8i 8.1.6.
I know of three different Oracle XA drivers: WebLogic jDriver forOracle XA, Oracle
OCI type 2 driver XA, and Oracle Thin tyoe 2 XA. Are there any otherdrivers
that I can use for Oracle 8.1.6? Which driver and which versionshould I use?
For example, can I use the Oracle 8.1.7 JDBC drivers with the Oracle8.1.6 server,
or would the Oracle 9i drivers work with the Oracle 8i server? Whichdrivers
are faster, and which support more features? I assume that I shouldnot use the
type 4 driver since I am not using an applet, but I don't know ifthere are bugs
in the OCI C library for Solaris or in the JDBC drivers that use itthat prevent
XA from woking. Which version of the Oracle C OCI library should Iuse if I use
a type 2 driver?
Thanks,
Ross Goldberg

What word processing program should I use with my Mac, what word processing program should I use with my Mac, what word processing program should I use with my Mac

what word processing program should I use with my Mac?

steve359 wrote:
For free you can download NeoOffice
Not quite. Downloading the current version of NeoOffice is definitely not free (downloading the previous version is). The developers of NeoOffice (the most Mac-like of the StarOffice descendants) make a distinction between the application itself (which is free) and downloading it, for which they require what they are pleased to call a "donation" (since it's mandatory, I would call it a fee).
shldr2thewheel wrote:
I totally forget about TextEdit all the time..
Indeed. For basic WP tasks, TextEdit can be quite satisfactory.
embauerxz
I only need it for reports
Would that include the report on the state of the US economy -- you know, the one President Obama asked you to deliver to the White House no later than 7AM on January 4? The one in two columns, with numbered paragraphs, table of contents, footnotes, mathematical formulae, 40 figures, 60 charts, quotations in Arabic, Japanese, and classical Greek, and 15 pages of references in APA style?
Grant Bennet-Alder is right -- "the real answer depends on what work you expect to do with it, and with whom you expect to do this work". There are dozens of word processors for Mac, from the venerable Word to the no less venerable Tex-Edit+. It would pointless to start listing them all, when many of them might be either too little or too much for your needs.

What type of repeater should I use with my new Airport Extreme?

what type of repeater should I use with my new Airport Extreme? Thanks.

If you want to repeat both bands of your dual band AirPort Extreme, another AirPort Extreme would meet these requirements.
If you only need to extend one of the bands that the AriPort Extreme provides, then an Airport Express would do that nicely.

What kind of convertor can I use with my I mac in Israel?

What kind of convertor can I use with my I Mac in Israel?

What do you want to convert? More details about what you are trying to do would help.

My iMac was infected with a virus or malware the other night. I was told that I didn't have any firewall protection. How do I fix that? And what kind of software should I use to protect my computer from further attacks?

I am running OS X Version 10.9.5 on n iMac I brought in 2011. Had a virus or malware attack the other night and a window opened with a # to call for help. Didn't know if I should trust the # but ended up calling it anyway and paid to have them 'fix' things. Was told I didn't have firewall protection. Am not sure if I do now. [It still says to allow all incoming connections]. So what do I do now? And what kind of antivirus program is recommended?
Firewall

Read "Ransomware" web pages.
Assuming you let the scam outfit remotely control your Mac, the information on it can no longer be considered secure. Neither can the Mac itself. You should immediately shut it down and take actions to prevent or recover from identity theft, which is quite likely to have occurred. This means contacting the financial institutions and other companies that may permit access to your accounts using login names and passwords, canceling and replacing credit cards, and similar actions that only you can know.
Determine if you can contest the charge made to your credit card for this criminal transgression.
And what kind of antivirus program is recommended?
None. The Mac is highly secure against malware or virus intrusion, but nothing can prevent you from willfully installing dubious software or granting remote access to criminals. No "anti-virus" software in the world will protect you from that. The OS X application firewall is not intended to prevent this sort of occurrence.

What kind of T1 service to use with a T1 IMA card?

If I have two routers geographically separated, and each router has a 4 port T1 IMA ATM module, what kind of T1 service do I need to order?
Let's say I want 3Mbps bandwidth. So, I have to order 2 access T1's at each location. Now, do these T1's have to be leased lines? Can they be frame-relay? Can I connect the IMA card to a provider's ATM network??
Also, will a multiport IMA ATM card support just one T1, or does it have to be at least two??

The IMA cards are specifically for
ATM network connectivity;
http://www.cisco.com/univercd/cc/td/doc/pcat/mut1e1p1.htm#xtocid1
You can use any number of the 4 ports
that you wish.

What kind of motor should I use for lifting a heavy load?

I'm working on an automation application in which I need to control a lifting mechanism with heavy load (about 120 lbs). I will be getting constant temperature readings and based on that data I can determine the rate of change of the temperature. If the temperature rate is too fast then I need to be able to slow down the motor, if it is too slow then I need to speed it up. I'm looking for some support with choosing the right motor and hardware so that I have full speed control, while still being able to lift this heavy load, hold the load in a certain position, and then raise the load back to its original position. I was considering a stepper motor for this due to its ability to brake so the load can stabilize. Is this the right call or should I use a continuous servo? Where can I get such a stepper that can handle this type of load and has software that interfaces with LabVIEW? Would I be safe getting low-cost hardware for this application? Any guidance would be sincerely appreciated. Thanks.

Thanks for your replies to this topic. I just discovered the worm gear option yesterday while talking to a professor. I think that is the route we are going to take because the DC motor won't be as expensive as a high-torque stepper or servo. Also, I have three engineers that will be calculating the motor size based on gear reduction, spool size, cable length, and the load that we have to lift (which is about 120 lbs.). If any of you would like to suggest a motor size, that would be great too. I'm thinking something around 1HP should probably do it. My goal is to stay cost-effective while making an easy apparatus. I know that the worm gears may also be inefficient at times but it seems like the best solution for this application. Not to mention it's not to hard for our mechanical engineers here to make the spool and bearings. And I believe you can buy a DC motor that interfaces directly with a worm gear. However, a follow up question is what computer hardware do I need to control the voltage of the motor so I have speed control? Is this done through an RS232 board? My output from the LabVIEW program will be voltages, from which device is that binary signal converted into physical voltage? Thanks for your help so far.

What kind of SSD should I use and will it benefit my laptop?

My Macbook Pro (either early or late 2008, not sure) is in dire need of an upgrade. I'm thinking about upgrading it to a 128 GB SSD-drive and was wondering if anybody has experience with the performance-gains (especially in Adobe Photoshop) and what kind of drives anyone would recommended? It's quite difficult to find recent info on this online so any help would be greatly appreciated.
Cheers,
Michiel

Ah, this opens up new perspectives. Could you shed some light on the RAM-subject? How can I find out what model I have and what kind of RAM I need? I mean, logic dictates I need the same RAM I have now, but I'm sure there has been some development on those voodoo-sticks that should make them faster etc.
Also, any info on the SSD-thing is still greatly appreciated. Upgrading RAM ánd HD is ofcourse better then just switching to an SSD..

What kind of RAM do you use with your K7D Master-L? (esp. unbuff)

I was windering what kind of RAM people sue with their K7D Master-L mobos. I recently got one with a 512 stick of Mushkiin Level 2 CAS222 RAM however I'm having boot problem. I'm going to test registered RAM soon to see if that is the problem.
Have people had success with unbuffered RAM? I really want to use Mushkin or Corsair XMS RAM for their high performance and overclockability, but if I can't oh well
-Matt

Use registered. I have used kingston and infineon working fine ( besides some funny things at some point)
Senior people will tell you there isn't any choice...

HT5299 What kind of cable should I use for movies on my macbook pro if I want to watch it on my 60 inch tv?

What kind of cable for my macbook pro, do I use to watch movies on my 60 inch tv ?

Which model MacBook Pro do you have (e.g., "15-inch Late 2011")?
Clinton

What version of AR should I use with Win XP to avoid App Error?

When trying to access a pdf file, I receive the "AcroRd32.exe - Application Error." The description reads: "The exception unknown software exception (OXc0000409) occured in the application at 0X0040492a." Once I close the error, the pdf file is not an issue to open or close.
I'm using Adobe Reader XI (11.0.03) with Win XP and read somewhere that I should be using an older version of AR, like 8 or 9. I hate to go through removing my current app without further advise. I would appreciate help with getting this error issue solved! Thank you.

Thank you Pat. I have disabled Protected Mode, and opened about 4 pdf files without issue, but with the next one, I received the same error message. I don't understand why this error doesn't appear when accessing every pdf file.
As it turns out, sometimes it takes quite a while, often 2 to 5 minutes, for the error to show up. The only thing that changes in the description is the location - sometimes 0x0040122b and sometimes 0x0040492a, but it seems to show up consistently now that I know to wait.

What kind of printers can I use with mountain lion?

i have a MacBook Pro
OSX 10.8.5
what brand of Printers can I use, compatible with Apple Computers with OSX 10.8.5

Welcome to Apple Support Communities
Most printers are compatible with Mac OS X. You can find the list of all printers supported in this website > http://support.apple.com/kb/HT3669
Main brands like HP, Epson or Canon sell Mac-supported printers, or you can have a look at the Apple Online Store > http://store.apple.com/us/mac/mac-accessories/printers

What kind of database can I use with jsp pages?

Well I have been an ASP programer for a while and now I want to be able to host sites on an Apache server so that means i need to just jsp pages or something that is not windows dependant. So I need to start a database, a small one just for client information, and I don't know what to create it in. I was going to use MS acess but I am guessing that won't work with jsp. So what are my options for desktop database applications? Should I download star office and try that I havne't ever used that but I imagine it comes with some kind of database program. Well let me know thanks.

JSP should work with any database that worked with ASP. The key is to use JDBC which is the equivalent to ADO. As long as you get the appropriate driver for the database, you're all set. As the previous poster mentioned, for MS Access you must use a JDBC-ODBC bridge which is really a JDBC driver that works on top of ODBC. This is the worst performing type of driver, but if you're using MS Access then perhaps performance isn't a priority.
Check out the Sun tutorial on JDBC if interested.

What kind of path should be used in a *portable* .getResource()?

I am porting to NetBeans an application that was running fine under JBuilder. There is one type of statement that refuses to be ported (getResource()).
The application contains a lot of lines like this:
url = AnnualReportsDialog.class.getResource("images/CheckMark.gif");Even the JBuilder tutorial has the same kind of file access relative to some current or default directory:
ImageIcon image1 = new
ImageIcon(hello_world.HelloWorldFrame.class.getResource("openFile.png"));When the "url" line above is reached, the getResource() fails.
I have tried several variations:
url = AnnualReportsDialog.class.getResource("C:\\images\\CheckMark.gif");
url = AnnualReportsDialog.class.getResource("C:/images/CheckMark.gif");but they don't work.
Perhaps something has changed between JRE 1.4 and 1.6?
What is the more general solution to the problem of Java not having a 'chdir()'? My app runs on Windows but I would like to run in in *ix as well.
Is there a way to place all those GIFs in some sort of resource, that can be carried around different O/Ss and filesystem paths? I would like the following to work under any OS:
getResource("images/CheckMark.gif");
TIA,
-Ramon

X-FI PCI 32Bit Cards?with 33MHz will fit into a PCi 64Bit slot. (The Slots must only support PCI 2.2 or later.)?Even a PCI-X slot can dri've PCI 32 33MHz cards. Downside: the PCI bridge will clock down all connectet PCI slots to 33MHz. Most PCI 64Bit slots supports 66MHz clock speed.
Older PCI cards like Audigy will run in a 2. or lower?compatible PCI Slot.
Message Edited by fffcmad on 03-26-2008 0:3 PM

What kind of card should I use with my DAQ setup?

Similar Messages

Maybe you are looking for