What needs to be done to avoid WIFI drop-offs with Apple AirPort Extreme Base station with Extended Wifi
Hi there,
can anybody please advise me what needs to be done to avoid WIFI drop-offs every half an hour or 1 hours.
I use voip phoe calls a lot using my WIFI, However my AirPort WIFI connection drops-off while I am in the middle of WIFI VOIP calls. This is causing significant disturbance in my family.
Please assist.
In details, I have extended my WIFI range using 2 Apple Airport Extreme Base Station.
Main Base is - A1408 9 (5th Gen), and I have extended my WIFI in my L shape house by connecting another Apple AiPort A1354 ( 4th Gen) with AA1408.
Note1:
> when I am close to A1408 my iPhone4 connected with A1408 automatically
> When I am close ot A1354 , my iPhone4 connected with A1354 automatically.
Note2: these drop-offs never occurred when I had only 1 Apple AirPort Extreme Base station WIFI
I think, this Auto switching causing the slight drop outs in my Wifi when I am on the VOIP call.
Do you think that something is going wrong with my Apple AirPort Wifi extended?
Much appreciated
To help eliminate drop-offs you need to ensure that your extended network is operating at its peak bandwidth performance. Base station placement is critical in an extended network. Please check out the following AirPort User Tip for details.
Similar Messages
-
Hi I'm from Australia.
If I buy an Apple Airport Extreme Base Station and I have an Optus Cable internet. Do I really need an Apple Care Protection? or I don't have to?Any specific recommendations for a standalone ADSL modem though?
Always a good idea to use the modem that your service provider supplies or recommends....often free....since you know that it will be supported in the event of connection difficulties.
I have made the mistake of choosing the "best" modem based on test reports....only to find out later that the ISP would not offer any support when I was having connection difficulties.
The ISP blamed the modem. The modem support folks blamed the ISP. -
I have an Appl,e AirPort Extreme Base Station (Simultaneous Dual_Band( MC340LL/A. After updating the software, no devices can connect via wifi.
As suggested in another discussion area, (AirPort), I reset the AEBS to factory defaults. On the TV, I went to >Settings>General>Network>Configure Wireless>Wireless Networks. I could then see the generic "Apple Network xxxxx" on the TV. From my MacBookPro, I verified that I could connect to the TV by launching iTunes and noting that the TV was now visible in the "Devices" menu. Went back to the AEBS and ran through the "Setup" routine. I did NOT use the "Previous Settings" but instead, saved the old settings profile, created a new wireless network and new settings profile and enabled WPA2 Personal encryption. I then went back to the TV and went through the "Settings" routine again (as noted above). This time, after entering my WPA2 password, the TV connected to the network and problem was solved. Thanks.
-
Hello Anyone and Everyone who can answer my question,
I would like to be able to offer wireless access to the internet for my guest's who use my apartment above my garage that is about 75 feet away from my house/computer. I have a MacBook Pro and have satellite internet service through an ehternet connection. I recently purchased an Apple Extreme Base Station with simultanious Dual-Band (MC34OLL/A), that is in the process of being shipped as I type, and am wondering if I need anything else to install in the apartment for the wireless to work with the Apple Extreme Base Station? Thank you for any help in this matter.
Sincerely,
LizzyIn AirPort Utility, enable the guest network by selecting your Extreme, then the Edit button, then the Wireless tab, then check the box for "Enable Guest Network":
-
What needs to be done to avoid the vulnerability discovered according to hacking story yesterday?
what needs to be done to avoid the vulnerability discovered according to hacking story yesterday?
abombaci wrote:
This software update is only available for people that have Java installed on their Macs. For someone like me since I don't, I don't get the update because I don't need it.
Then you don't need to worry about the Java vulnerability being exploited on your Mac. -
What is the most sensible way to extend a wifi signal. I am in a cinderblock house and I have to buy something that will give me a single network but added range from my airport extreme base station.
Use an Airport Express. Configure the AEBS to allow it's wireless network to be extended. This is a dropdown menu option under the Wireless tab. Configure the Airport Express to Extend an Existing Network also under it's Wireless tab. You will need to provide the name of your network used in the AEBS as well as the network's access password.
-
Need Help
Let's see if I can get this straight.
You have an Airport Extreme base station that is set to "Create a wireless network" and you have the box checked for "allow this network to be extended"....
Then you have an Airport Express that is set to "Extend a wireless network" which you selected the name of your network in the box...
Correct?
See this Apple document:
http://support.apple.com/kb/HT4259?viewlocale=en_US&locale=en_US
The wireless unit on the right of the diagram can be either of the newer Apple base stations.
Extreme, Express, Time Capsule -
Thanks in advance for any help you folks can offer. I'm a newb here and will try to offer as much detail as I can about the dilemma at hand.
Scenario: Home network has been recently set up for wireless internet access via NEW Airport Extreme Base Station (purchased September 2011). Units accessing the network include: 2011 Macbook Pro, 2011 Macbook Air, 2007 Macbook, 2009 Macbook Pro, 2 iPhone 3GSs, and a 1st-gen iPad (and a partridge in a pear tree AEBS is configured to run WPA2 encrypted network, as well as a WPA2 guest network. I am attempting to yoke a BROTHER HL5370DW wireless B or G/ ethernet / usb-capable printer to the main network such that any and all units can print wirelessly or its equivalent (i.e., via printer hooked to AEBS through USB hub)
Problem: Despite configuring the Brother printer to recognize the main WPA2 network I created, I am unable to get wireless printing to work. My workaround was to physically connect Brother printer to AEBS via USB, specifically using a Belkin USB hub (after all, I wanted access to usb drives, as well as the printer). This workaround works ONLY SOME OF THE TIME. Generally, after a fresh boot of any computer or after a restart of the AEBS, any given computer will be able to print (i.e., any computer wirelessly connected to the main WPA2 network recognizes the printer). HOWEVER, at random times, printer access is gone (as is access to USB drives connected to AEBS's usb hub). Wireless networks are still up and running when that happens. IS THERE A WAY TO GET THE USB HUB's devices (i.e., printer and usb drives) to ALWAYS REMAIN AVAILABLE AS LONG AS THEY STAY CONNECTED TO THE AEBS? In other words, what accounts for the intermittent loss of the usb peripherals?
Sometimes, I just shut the airport off on whatever computer is having this problem, and the problem goes away. Sometimes, the problem is present across all computers in the house, sometimes only a few are affected. I can ALWAYS see the AEBS in the Airport Utility if the AEBS is connected to the particular computer via ETHERNET CABLE.
My theories:
- true wireless printing (i.e., without usb hub workaround) doesn't work because the N network somehow isn't backwards compatible with the Brother printer, which, i believe, is B/G. Although...isn't Wireless N networking supposed to work with BG devices? I did find a thread (https://discussions.apple.com/thread/2570774?start=0&tstart=0 ) that explains some of the particulars of WPA2 encryption and Wireless B/G issues, but it was beyond my level of comprehension (I'm a psychologist, but not an Apple Genius
- The usb workaround is only intermittently viable because of some flaw in the Airport or Airport Utility that causes dropouts to happen when a Macbook Pro or Air's lid gets closed or one gets opened after having been at a different network (e.g., at my office).
QUESTIONS:
- Should I try to use my old router (7 year old Linksys WRT54G) as an access point and connect the Brother printer to that G-router? How do I do that?
- I wouldn't mind just relying on the usb hub method if I could just insure more consistency (i.e., no random dropouts of peripherals). How could I do this?
Rule out:
- wireless printing works on my printer - it was being recognized back before the AEBS. I had the Linksys router running a WEP network and had the wireless printer talking with no cables to the router and the computers. (I just don't want to revert to using WEP encryption given its lack of security and my trying to protect HiPAA related health information on behalf of patients)
Any help will be greatly appreciated.
Thanks in advance!13 ASCII characters = 104 (aka 128)-bit WEP
encryption
If turning off WEP works, then you just need to
provide the cameras with the "Equivalent Network Password".
One of the problems with WEP is that the actual
standard relies on a 10 character HEX key for 40bit
WEP and a 26 character HEX key for 128bit WEP.
In order to make things easier, vendors use certain
algorithms to convert simple alphanumeric passwords
(or passphrases) into HEX keys, thus enabling the use
of simple easy to remember WEP password rather than
lengthy HEX keys. The problem is that different
vendors use different algorithms to generate the HEX
key and therefore a ASCII password on an AEBS will be
hashed differently on a non-Apple client and vice
versa.
You may find the following article helpful:
- Apple article, especially the part about
"Third-party client to Airport".
Brilliant idea about trying the system with No encryption on... that DID solve the problem... almost.. once I turned off the encryption option, and restarted the Airport, I got a dialog box showing that the "Base station needs attention" but it didn't indicate WHAT kind of "assistance" it needed. Nonetheless, I closed out of the Airport program only to find that the indicator light, which had been Green, was now, flashing Yellow and I could not connect anything, including my computer. I opened the Airport program again and found the ONLY way I could get the Green light on was to select some sort of encryption option... then the light would go Green again but my cameras would not hook up again, and when I went back in and ONLY changed the option to NO encryption, I got the yellow flashing light and the "this base unit needs attention" warning...
I think your suggestions are almost on the mark... is there any way of reconciling the WEP coding between the cameras and the Airport??? Or turning off the encryption option and STILL have Airport work?
Thanks again for your help and suggestions... I really appreciate it.
geoff -
Hi. In November I set up my airport extreme base station (5th generation I believe) to wirelessly extend the wifi network we use at home to see if it would increase download speeds. Before doing that, I did a factory reset of my airport extreme, and the owner of the airport extreme to which the ethernet cable is attached made changes to his network to allow it to be extended. I folllowed all the directions from the apple support pages, and finally got it to work. I could even access a portable hard drive which I attached to the airport extreme base station being used as the extension. Then a week or so ago I noticed that my laptop would no longer connect to my base station. I did not have time to look into it until this week. Airport utility, either on my Mac or iphone no longer recognizes my base station. My mac is running OS X 10.10.1 and my iPhone is running iOS 8.1.2 I have tried both hard, soft and factory resets of my base station to no avail. The only thing that has changed after doing that, is that when I do a soft reset of my base station, a neighbors airport express appears when it never did before. I can't actually connect to it, but it does try. Then after approximately 5 minutes, it disappears from my list.
Today I went and pulled out my OLD AIRPORT EXTREME base station... you know, the one that looks like a space ship and is running wifi 802.1 b/c? airport utility DOES locate and display that, but airport utility returns a message stating that it cannot be set up by this software. I am attaching an image of that.
Thank you,
John
Does this have anything to do with the fact that 'Back to My Mac' is probably enabled?I think the initial problem is that your iPhone was connected to an open network that wasn't yours.
Go to Settings > WiFi and "Forget" the network created by that AirPort Extreme, it's older than dirt. Forget your neighbor's network also.
Perform the equivalent actions with your Mac: System Preferences > Network > Wi-Fi > Advanced... Delete every network that appears, including your own.
Then, connect to your own network on all your devices, after which you ought to be able to use any of them and configure your Extreme without any difficulty. You may need to start over with a "hard reset" on both the main AirPort Extreme and the one extending its network.
Does this have anything to do with the fact that 'Back to My Mac' is probably enabled?
Not exactly, but using iCloud Keychain will populate all your devices with the names of preferred networks that any of them connect to, no matter where they are. I don't know why Apple considers that a beneficial feature. -
Can I buy an Airport Express plug-in wifi signal booster to connect to a Cisco wireless router, or do I have to buy an Airport Extreme base station to make the Airport Express plug-in work?
You would need either an AirPort Extreme or an AirPort Express connected to the Cisco router, with a permanent Ethernet cable connection.
Configure the Extreme or Express that is connected to the Cisco router to "create a wireless network".
Then, you could add an AirPort Express to "extend a wireless network" to provide more wireless coverage for the network that the Extreme or Express would be creating.
Remember that the Express can only "extend" the quality of signal that it receives, so it must be located where it can receive a strong signal from the "main" AirPort.
If you don't need the Cisco wireless signal, you could turn it off.....or use that network for guests or something similar.
The bottom line here......you always need two Apple routers if you want to extend the network wirelessly. -
External hard drive on Airport Extreme Base Station - need some help!!
Can you suggest an external drive make and model that works with the extreme? Need around 300 gb?
What format should the drive be in so my Windows Vista and Windows 7 and my mac will be able to backup to it?
What backup software do you recommend that I run on my Windows Vista and Windows 7 PC to it?
ThanksCan you suggest an external drive make and model that works with the extreme? Need around 300 gb?
There are literally dozens of external USB hard drives that will work with the 802.11n AirPort Extreme Base Station (AEBSn), but of course, not all. Please check out the following iFelix site to see some that are not recommended. FWIW, I currently use both a Newertech miniStack v3 (750 GB) & a Western Digital MyPassport (500 GB) with my AEBSn without any issues.
What format should the drive be in so my Windows Vista and Windows 7 and my mac will be able to backup to it?
HFS+ for the most efficiency between the AEBSn & the drive(s). Note that the AEBSn's file server will support both AFP & SMB when communicating between Mac & PCs (respectively) for file services. If you don't have a Mac, you can always format the drive in FAT32. Only NTFS (or any of the Linux partition formats) will not be supported by the AEBSn file service.
What backup software do you recommend that I run on my Windows Vista and Windows 7 PC to it?
I use Genie - soft's Genie Backup Manager, but just about any backup software that supports network-attached drives for backups should be fine. -
Can Airport Extreme Base Station 802.11g Connect To Park's Free WiFi?
The RV resort where I'm staying has free WiFi for Internet connections. It shows up on my iBook's Airport list of possible networks in the menu bar, along with my own local network which is an older Airport Extreme Base Station (white dome 802.11g) which has my HP printer plugged into it via an ethernet cable.
However, when I am connected to the park's WiFi via the laptop's Airport network choices, I am NOT connected to my AEBS, and therefore cannot print to the printer wirelesslessly. Is there a way for the AEBS to make the connection to the park's WiFi so I can use both Internet and printer from my iBook G4 without having to switch from one network to use the other?Is there a way for the AEBS to make the connection to the park's WiFi so I can use both Internet and printer from my iBook G4 without having to switch from one network to use the other?
Sorry, but no. You cannot connect your iBook's AirPort to more than one wireless network at a time. Since it will be highly unlikely that you will be able to create a Wireless Distribution System (WDS) between your RV resort's Wi-Fi and the 802.11g AirPort Extreme Base Station (AEBS), you won't be able to extend it to meet your needs. -
I need help with connecting an external HD to Airport Extreme base station
So i have the base station set up, and it recognizes my hard drive in the airport utilities and have the file sharing turned on, but when i connect to the base station wirelessly from my macbook pro, the hard drive and base station does not show up in the shared section in my finder. Any ideas as to whats up?
I'm having a similar problem, and I hope you'll excuse my ignorance but is there a difference between rebooting and just restarting. I've done the latter (numerous times) but not the former.
I have set up my Airport Extreme Base Station to my wireless router (DSL Internet connection) and to an external hard drive (MyBook Essential 640GB with USB connection). Internet works fine.
When I plug the hard drive directly into my MacBook it recognizes it fine, I can copy files to it, add folders, explore them etc.
When I plug the hard drive into the Base station, it appears as a network drive on the side bar of my finder window, but when I click on it to open it, it is empty, it shows 0 items and the available memory, but none of the files I put on it are visible to explore. -
I have been searching the Apple communities and Internet for a final answer. I just bought an Airport Extreme Base Station (5th generation) and LaCie d2 quadra 1TB external drive as a replacement for TWO failed Time Capsules, neither of which Apple would replace due to failed power supplies. I formatted the 1TB drive using Disk Utility (Mac OS extended (journaled)) from my MacBook Pro, and then plugged into the Airport Extreme Base Station USB port. The Airport Extreme Base Station see the Hard Drive, and my MacBook Pro sees the Hard Drive in my finder under shared resources. Time Machine, however, does not see the drive. Is there a solution for this problem? If Time Machine will not work, is there another software product out there that will work, like Carbon Copy. Having to plug the backup drive into the USB port of your laptop every evening kind of defeats the purpose of having a laptop. Any suggestions would be appreciated.
Keeping in mind that this is not supported by Apple, I have been successful at doing the following:
1) Format the entire drive (1 Partition) as Mac Extended (Journaled). You must click in Options and set it as a GUID Partition Table (first option)
2) Plug drive via USB to AEBS
3) Using Airport Utility, use Manual Setup, then under Disks, select the new Disk and click File Sharing, then Enable File Sharing and Secured Shared Disks (recommended, of course). Other settings are up to you.
4) IMPORTANT: you will NOT see this Disk in Time Machine until you open Finder and double-click on it. You will not need to do this again (hopefully).
5) Now it should appear in Time Machine. Remember to exclude any large files like Virtual Machines, since they will be re-backed-up (is that a word?) every time it changes in any way.
6) Remember that the first backup (over WiFi) is the longest. Leave the computer alone during this period.
Good luck, and let us all know how it went for you! -
After a recent iTunes update attempt iTunes no longer functions and the airport extreme base station is not accessable on our computer. We still have wifi but cannot access the base station software.
Thanks for the reply. I appreciate the response. I tried that approach this evening and it didn't work for me. (Technically it worked for me, when I was hardwired into my base station, but would not work for me wirelessly, which is my main issue.)
Again, using the approach you recommended works only if I have my ethernet cable attached to the LAN port so my computer is communicating directly to the base station through the hard wire. I am able to scan for my base station and make setting adjustments normally this way too.
As soon as I disconnect from the LAN port and try to go wireless is where I run into problems. The Base Station's wireless network I created is available to choose in the top right corner of the monitor with all of the other available wireless devices/networks -- but the network I created does not have access to the internet. I am also unable to configure my Base Station wirelessly. When my Airport Utility tries to scan for the Base Station and Network, it cannot find any Apple Wireless Device. It's like the Wireless Network in my base station is not sending out a signal.
Is there a way to resolve this issue?
Maybe you are looking for
-
Why is my Creative Cloud desktop app telling me I don't have any apps installed, when in fact I do?
Just noticed this forum so thought I'd post my question in here too... So, I [think] I just downloaded the latest CC desktop app/manager and when it finished etc and opened up, it's now telling me that I don't have any apps installed. I do, I have PS
-
CSS layout and IE6 suddenly gone wrong
Hi I have been working on a site, unfortunately I diont have a copy of IE6 but looked great in IE7 and FF, checked through development in IE6 when i had the opportunity, suddenly at the last hurdle it seems to have gone terribly wrong and I have no i
-
Dear Experts, Am trying with User Exit (V50EPROP) EXIT_SAPLV50E_001 to create Default data of Transportation in Delivery Header Foreign Trade/Customs data. This Exit working for Foreign Countries but not working with in the same country. Eg: IN to IN
-
Offline approval for Purchase order response
Hi All, Currently we are in SRM 7.02. we want to know whether offline approval is applicable for Purchase order response (PCO). I have searched all available blogs but in Vain. Hope someone can enlighten me in this topic Regards, Nishanth
-
Unable to view custom folders (SQL)
Hello I've created an sql folder in "The Discoverer V5 EUL" BA. Desktop users are unable to view and use reports based on the sql folder, although complex folder are available. also, sql folders on other BA's are available can someone advise?