What RAM is needed for Laserjet Printer CP1525nw Windows 7 64-bit

Hi,
just found your post...
To install your HP1010 on Win7do the following:
Start
Devices & Printers
Add a printer
Adda local printer
Use an existing port: DOT4_001 (Generic IEEE...)
Next
Pick HP from manufacturer
Select HP LaserJet 3055 PCL5
Next
Name the printer something to your liking
Finish (or so, just follow the prompts)
Here you are!
Works every time for me, never had a problem from any application.
I don't know how this forum works and if i am notified if you reply or anyone else posts on this thread, so i try to check it again soon to check if you left a message. Be with me...
Matt

Similar Messages

Can someone help me tell what Ram i need for my macbookpro 7,1

please help my an tell me what speed and everything for my macbook pro7,1 13''
Model Name:          MacBook Pro
Model Identifier:          MacBookPro7,1
Processor Name:          Intel Core 2 Duo
Processor Speed:          2.4 GHz
Number Of Processors:          1
Total Number Of Cores:          2
L2 Cache:          3 MB
Memory:          4 GB
Bus Speed:          1.07 GHz
Boot ROM Version:          MBP71.0039.B0E
SMC Version (system):          1.62f7
Serial Number (system):          WQ0191N5ATM
Hardware UUID:          3AB05D30-0C69-5962-BFE8-FEC2780C76AD
Sudden Motion Sensor:
State:          Enabled

8GB (4GB X2) or 16GB (8GB X2) 1066MHz DDR3 SODIMM.
Do not use non-Apple Certified RAM.
Install RAM made by the following:
Corsair - Crucial - Mushkin - G.Skill - Kingston (non Value) - Patriot Mac Series.
The ones to avoid:
PNY - Kingston Value RAM - Corsair Value RAM - No Name RAM
Good luck

What patches are needed for OCS R1 singlebox Windows installation

Hi there,
I'm trying to install OCS R1 on Windows 2000 server and I wanted to know if I need any patch to perform the installation.
I'm following the Note 221812.1 and according to it I have created email accounts as mailadmin (System Administrator) and now I should apply the patch 2606325, but I don't know if this is required for Windows. It probably is, because I skip this step and test the mail system by sending mails between the accounts already created and I get a message which says that: an error has occurred at attempting to send the message.
I don't know if this is due to the fact that I haven't applied the patch or due to something else...
I would appreciate any help.
Best regards,
Jorge

I tried to check out that note of yours, i think it no longer exists, the same goes for the patch number.
Anyway from my linux install as far as the installation goes, there was no need for patches ocs installs without them. However if you want to use something like workflow for files, then you need a few patches.
Firstly you need to patch which is applied after your workflow installation - i cannot rememeber its number, but you should find it in eithr the files admin guide or files release notes for 9.0.3.
In addition to that, when you install workflow, you also need to add a few languages, which if you do not with result in your workflow/files integration failing.

What is the need for setting property data inside the JMSMesage

Hi
Could anybody please let me know
*What is the need for setting property data inside the JMSMesage??
For example i have a seen a similar example as shown ??
I have seen a
Message.setStringProperty("Sport","Basketball");
and also please tell me how can the MDB recievies this property data ??
Thanks in advance .

raviprivate wrote:
Could anybody please let me know
*What is the need for setting property data inside the JMSMesage??
For example i have a seen a similar example as shown ??
I have seen a
Message.setStringProperty("Sport","Basketball"); Look at the detail JMS documentation on [Message Properties|http://java.sun.com/j2ee/sdk_1.3/techdocs/api/javax/jms/Message.html] .
>
and also please tell me how can the MDB recievies this property data ?? MDB onMessage method argument is the Message object and if you look at the documentation, Message interface has getter methods to retrieve the properties.

What is the need for calling default constructor by JVM?

What is the need for calling default constructor by JVM? why the JVM should intiializes default values to the data
fields if the constructor is not there in our class?

mahar wrote:
What is the need for calling default constructor by JVM? Huh? The JVM does not need to call the default constructor. It needs to call a constructor.
You decide which one by the way you use "new".
why the JVM should initialize default values to the data fieldsHuh?
... if the constructor is not there in our class?Huh? The default constructor is always there. It may be private but it is still there.

What ram to buy for mac mini ?

What ram to buy for a 2007 mac mini intel core 2 duo 1.83Ghz? can you tell me site too like newegg thanks.

http://support.apple.com/kb/HT4432?viewlocale=en_US&locale=en_US#3 You can use 2 GB DDR2 667 MHz. Purchase that in OWC

Just bought a new iPod touch 16G - I think it's a 5th gen. - I used my old iPod to record rehearsals. The new one is stating that my Belken mic is not compatible. Can I record with this new one? If so, what do I need for a mic?

Just bought a new iPod Touch 16G - (I think it's a 5th gen.). I used my old iPod to record music rehearsals. This new iPod is stating that my old Belken mic (with new adaptor) is not compatible. Does this new iPod Touch have ability to record audio? If so, what do I need for a mic??

Thanks very much! I found the app, tested it, and it sounds fairly lifelike. Big help!!

I have already bought a macbook pro in USA and I want to use it in Europe. What adapter I need for my Airport Extreme?

I have already bought a macbook pro in USA and I want to use it in Europe. What adapter I need for my Airport Extreme?

No power adaptor is needed as the power units are auto-switching. But you will need wall outlet adaptors such as you will find in Apple's World Travel Kit, at AAA stores, and other vendors.

HT1222 Since I'm an American, what's the need for me to update?

Since I'm an American, what's the need for me to update?
How does the new update apply to me?

What update are you referring to? If you mean iOS 6.1.3, there are a number of security updates that apply to all iOS devices:
http://support.apple.com/kb/HT5704
If that's not what you mean, please explain further.
Regards.

Can someone tell me what settings I need for ipad texting. Went to Mexico and now can't get the texting to work at all on ipad. Thanls

Can someone tell me what settings I need for ipad texting. I went to Mexico and when I returned the texting does not work on my ipad. The support at Apple wanted to charge me to get info.
THanks

Can't address the problem directly, cause even though my iPad4 is Cell+Wi-Fi, I've never put a SIM in it and never had the need to text, SMS or iMessage, from it. When away from the office or home wireless network, I tether it off the iPhone. Skype, both text and video, work just fine thru the Wi-Fi link, though.
HOWEVER, when I was hashing out the contract details to get the iPhone 5 about 14 months ago at Telcel, the representative distinctly mentioned that both Visual Voicemail as well as iMessages would be included in the package and they would be mandatory cause "I was getting a (subsidized) Apple iPhone" on a 24 month leash. Then when the gizmo came out of its box for SIM installation and activation, she went thru the motions of making sure both were working properly. So I assume the carrier has some say in the matter.

What Equipment is Needed for CCNP Security Lab

Hello,
Im Looking to find out what Devices are needed for a ccnp security home lab. I keep hearing that 2 5510's are a must for labbing. The downside Is the Prices avg $800 each on the low end. I also saw some ppl had an ips in their lab. Im looking to find out what is 100% needed. I alredy have a lab in place used for my ccnp r&s.
Thanks

I would also say that two ASAs is a must to practice with them. But in my opinion, 2 5505 SecPlus are enough. What are the differences to the 5510? You configure subinterfaces instead of vlan-interfaces. But that's something you know from R/S. And the failover is only stateless, but failover in general also works. Sof if you find these ASAs for less money, take them. IPS is probably the topic where most CCNP Security students are least familar with. So owning a sensor would also help.
And don't forget that the bigger CCIE-Training vendors have complete labs for rent with all you need for CCNP Sec preparation. That could also save some money.
Don't stop after you've improved your network! Improve the world by lending money to the working poor:
http://www.kiva.org/invitedby/karsteni

What all is needed for this type of Flash Design Studio

What all is needed for this type of Flash Design Studio.
There are a couple of sites out there that use both flash and
shockwave. I am looking ot get somethign like this started and need
some help getting pointed in the right direction. here are some
examples:
http://www.uberprints.com/studio/
http://www.customavenue.com/online-design-studio/online-design-studio.html
https://www.youdesignit.com/youdesignit.cfm
http://www.pixeltees.com/make

Rclarkhaddock,
> What all is needed for this type of Flash Design Studio.
There
> are a couple of sites out there that use both flash and
shockwave.
Of the examples you showed, I saw Flash (Adobe Flash),
Shockwave (Adobe
Director), and JavaScript, but never a combination on the
same site. (It
might make sense to combine Flash with JavaScript or
Shockwave with
JavaScript, but not really to combine Flash with Shockwave.)
> I am looking ot get somethign like this started and need
some help
> getting pointed in the right direction.
Any of the above technologies will do it. You could also use
a Java
applet or even a .NET solution of some kind, so the choice
you take will
depend largely on what platform you want to support and code
for. This sort
of project will require significant amounts of custom
programming. My
personal approach would be to use Flash, mainly because of
the popularity of
the plugin. The Shockwave example looks beautiful, and I
started out years
ago using Director, but fewer people nowadays have the
Shockwave plugin
installed. It doesn't look like any of the sites shown use 3D
modeling,
which is the only relevant feature that Shockwave has over
the other
approaches. JavaScript (probably some Ajax approach) would
work -- as
seen -- but then you're dealing with compatibility issues
among various
JavaScript implementations in the great variety of browsers
out there.
Flash minimizes that, in my opinion.
All you really "need" to produce what you've seen is Flash
and some sort
of database back end (MySQL, say), which means you'll need a
bit of
middleware (PHP, ASP, Cold Fusion, etc.) to act as your
ambassador between
Flash and the database.
David Stiller
Adobe Community Expert
Dev blog,
http://www.quip.net/blog/
"Luck is the residue of good design."

What permission is needed for a login to access the restored database(backup from different server)

what permission is needed for a login to access the restored database(backup from different server)
frequently reach the situation, when vendor restores a database, but he cannot access it unless I remap or add his login to the restored database. What permssion can grant the vendor so that he can but only can access the database he restored, not all other
databases.

Hi George,
According to your description, When you move a database from one server that is running SQL Server to another server that is running SQL Server, a mismatch may occur between the security identification numbers (SIDs) of the logins in the master database
and the users in the user database. As other post, you can use the sp_change_users_login stored procedure to map SQL Server logins. Also , you can use the following statement after doing the restore database. It will
fix the mis-mapped SID inside the restored DB.
ALTER USER <username> WITH LOGIN = <username>
For more information, you can review the following article.
http://blogs.lessthandot.com/index.php/DataMgmt/DBAdmin/MSSQLServerAdmin/do-you-still-use-sp_change_users_login/
Regards,
Sofiya Li
Sofiya Li
TechNet Community Support

What software is needed for system recovery? (cont'd)

What software is needed for system recovery of a Toshiba Satellite Pale8u-02p01D (also known as L355D-S7901) running Vista?
If I can just get the name/number for the recover software I will get it from eBay.
Thanks!
Solved!
Go to Solution.

Satellite L355D-S7901
If you want to look for that on eBay, look for the recovery discs for the model above. I doubt you'll find them there.
You can order them from Toshiba, of course.
   Order Toshiba Recovery Media
And you might get them cheaper from a third-party vendor.
   Digitalmedia-labs.com
   MyRecoveryCDs.com
   Recovery-CD.com
   RestoreDisks.com
   RestoreCD4u
-Jerry

Can't find the Audit Vault 10.3 software for the agent on Windows 32 bit.

the docs for 10.3 suggest windows 32 bit is supported but I can only find on edelivery the 64 bit agent kit.
Does anyone know where the 32 bit kit is please?
Thanks
Mike

I do see that in Section 1.1 of the 10.3 Collection Agent Install Guide. However Section 2.3 of that same guide refers you to the latest list of certifications (again, document 848402.1 ). Not sure why the inconsistency, but you might want to file a SR to get further clarification from Oracle.

What RAM is needed for Laserjet Printer CP1525nw Windows 7 64-bit

Similar Messages

Maybe you are looking for