What's cooking? My CPU!!!

I have resently purchased a K7N2-L mobo. I installed it with no great problems, but when I started it up, my CPU temp went through the roof. It's now idle at 65C and I know that's high. The wierd thing is that everything on my computer is the same except the mobo. I did have a MSI KT3 Ultra-ARU and my CPU temp ws idle at 42C. Now I have checked with a few different programs to see if this temperature was correct and everyone says 65C.
SpeedFan 4.08:
Temp1: 43C
Temp2: 52C
Temp3: 65C
PCAlert 4: 65C
BIOS Reading: 65C
Any ideas as to why it's running so hot? Plus my system now randonly reboots. I'm guessing it's because of the heat.

I have this Diana Case a littie bigger case than old baby AT cases. Likewise your problem the temperature was at 65 degrees C. The power supply was masking the AMD approved Coolermaster DP5-6J31C-A1 fan and cooler aluminium block. I remoeved the power supply out and tried again, with a surprise I get 45 deg.C . Than I put the power supply back to its place and put a case fan next to Coolermaster . Now I am reading 52 deg. C. I am going to get another case which power supply will not placeses near coolers fan.
But be careful there is some cases which is made of very thin metal. Whatever you screw on it it bends a lot. Even floppy jerks rigt or left when you try to insert diskette in it.
Bye.
Athlon XP1800+ 0.13micron
MSI K7N2-L bios3.0
Collermaster DP5-6J31C-A1
2X Kingston 128Mb DDR 266mhz
MSI agp4x MX440SE 64 Mb
MSI CD rom
300w P4 power supply
inca keyboard/chic scroll mouse
AP 250w speaker system

Similar Messages

What is cookies.sqlite and why does it slow the start up of mozilla by a minute or so. I found it and deleted it,fixed the problem, but it reappears eveery time I restart mozilla.

what is cookies.sqlite and why does it slow the start up of mozilla by a minute or so. I found it and deleted it,fixed the problem, but it reappears every time I restart mozilla.

AVG reports these sqlite cookies each time firefox starts. they usually belong to tribalfusion or some other tracker. How do I block them in the first place. I thought firefox is a safe browser. Did not have this problem until I upgraded to 3.6.

What is %IOWAIT of CPU states in TOP command output

What is "% iowait" in CPU States in Solaris? See below output it shows 11.2 % of CPU was used for IO.
Is CPU used in IO as well? If yes how?
last pid: 15598; load averages: 3.66, 3.39, 3.07 18:33:27
292 processes: 283 sleeping, 1 running, 5 zombie, 3 on cpu
CPU states: 17.9% idle, 54.8% user, 16.1% kernel, 11.2% iowait, 0.0% swap
Memory: 16G real, 8029M free, 5425M swap in use, 19G swap free
PID USERNAME THR PRI NICE SIZE RES STATE TIME CPU COMMAND

The value of %iowait is relatively semi-meaningless these days and as a result we removed it from Solaris 10 onwards. The parameter is still displayed in certain commands but it will always be zero.
System Administration Commands                         iostat(1M)
     wt        the I/O wait time is no longer calculated as a
               percentage of CPU time, and this statistic will
               always return zero.Which means top will also show zero, eg:
load averages: 0.08, 0.17, 0.16;               up 0+02:04:38
88 processes: 87 sleeping, 1 on cpu
CPU states: 96.1% idle, 2.4% user, 1.5% kernel, *0.0% iowait*, 0.0% swap
Kernel: 1181 ctxsw, 21 trap, 1056 intr, 2553 syscall, 13 flt
Memory: 3327M phys mem, 932M free mem, 1663M total swap, 1663M free swap

What are cookie domains used for?

there is a choice, can someone give me some suggestion?
What are cookie domains used for?
A/ to be easily recognizable by digital certificates that are also based on domains
B/ to instruct the browser that the cookie should be send only to the domain it came from
C/ to provide convenient way for the user to group cookies by their domains
D/ All of Above
E/ None of Above

Not only does that not appear to be a Java question,
but the OP didn't even take a guess at the answer and
explain why he thought that that answer was correct.thanks! i support with your viewpoint, solve a problem will be the most important mission, but not consured! i am cognizant of this is a mistake to ask other questions in java forum ,but this question didn't far away j2ee project, though this is a choice, but only get a answer is not my original intention! i hope i can call on anyone join in this discussion!
thanks...

What are cookies and cache?

I've heard every once in a while you want to remove your cookies and cache! Why is this? Is that true? And what are cookies and cache exactly? Like their purpose

The cache stores data from websites so you can load pages faster but on occasion the cache gets full and needs to be emptied.
Read here about cookies.
http://en.wikipedia.org/wiki/Internet_cookies
You can empty the Safari cache from the menu bar, Safari / Empty Cache.
If you have problems accessing a site, deleting the site related cookie can help. Go to Safari / Preferences then select the Security tab.
Click: Show cookies
You can delete all cookies or individually.

When I open email or texting I am often sent to the Web to either the Playstore to look at a new app or some site that want me to choose some singles site to chat with chick avatar. How do I remove this - what? cookie?

When I open email or texting I am often sent to the Web to either the Playstore to look at a new app or some site that want me to choose some singles site to chat with chick avatars. How do I remove this - what? cookie?

I will try safe mode.
I did download Ad Network Detector and opted out of JumpTap and AdMob. Today I found more: MoPub and Millenial which I will opt out of. I had previously opted out of Google Ads on the Cell phone but not on the net - so did that. Allegedly it take time for the opt outs to reach the originators of these pop ups
Thanks all for the suggestions - but not cleaned up yet.
Verizon Wireless Customer Support <[email protected]> wrote:
Verizon Wireless Customer Support created the discussion
"When I open email or texting I am often sent to the Web to either the Playstore to look at a new app or some site that want me to choose some singles site to chat with chick avatar. How do I remove this - what? cookie?"
To view the discussion, visit: https://community.verizonwireless.com/message/1081202#1081202
>

WHAT ARE COOKIES??

CAN ANYBODY TELL ME WHAT ARE COOKIES AND HOW I CAN USE COOKIES IN MY PROGRAMMES??

See http://www.cookiecentral.com/
The FAQ section probably has enough information to get going.
As for using them in an app... Google for cookies, sessions and servlets and I'm pretty sure there will be a document containing information on how sessions are implements using cookies (one of the main uses of cookies in webapps)

6380-E mobo - what's the max CPU?

Hi - I have an MSI 6380-E (KT3-Ultra2) motherboard. The manual says an Athlon XP 2200+ is the fastest CPU it can handle.
However, I believe I read that up to an Athlon XP 3000+ can be used if the BIOS has been updated.
The AMI BIOS version is 5.70 - the last one MSI released for this motherboard.
What is the fastest CPU this motherboard can handle?
Thanks
Joe

Hi - thanks for responding.
1 GB PC2700 333 MHz DDR RAM
Motherboard Properties
V5.7 022403
Motherboard Name   MSI KT3 Ultra2 (MS-6380E)
Front Side Bus Properties
Bus Type   DEC Alpha EV6
Bus Width   64-bit
Real Clock   133 MHz (DDR)
Effective Clock   267 MHz
Bandwidth   2132 MB/s
Memory Bus Properties
Bus Type   DDR SDRAM
Bus Width   64-bit
Real Clock   167 MHz (DDR)
Effective Clock   333 MHz
Bandwidth   2666 MB/s
Chipset Bus Properties
Bus Type   VIA V-Link
Bus Width   8-bit
Real Clock   67 MHz (QDR)
Effective Clock   267 MHz
Bandwidth   267 MB/s
Motherboard Physical Info
CPU Sockets/Slots   1
Expansion Slots   5 PCI, 1 AGP, 1 CNR
RAM Slots   3 DIMM
Integrated Devices   Audio
Form Factor   ATX
Motherboard Size   230 mm x 300 mm
Motherboard Chipset   KT333
Extra Features   Fuzzy Logic 4
Antec True Power 330 watt PSU
Individual dedicated circuits for +3.3V, +5V and +12V outputs.
Voltage feedback and tighter ±3% regulation maintains accurate voltage to all components.
Antec Low Noise Technology achieves the optimum balance between noise reduction and necessary cooling.
ATX12V compliant with +12V connector and Aux. power connector for use with AMD™ and Intel® based systems. Backwards compatible with previous ATX standards.
2 Serial ATA drive connectors.
Dedicated Fan Only power connectors allow TruePower to control the speed of case fans, reducing total system noise.
Very low minimum load: 0.8A at +12V
Nylon sleeve on wiring harness for improved ease-of-use and airflow.
Two double ball bearing fans.
Gold plated connectors.
Additional Info about PSU at this link:
http://www.antec.com/specs/true330_spe.html
Joe

K7N2 Delta: what are the fastest cpu available?

I have a K7N2 Delta-ILSR with a AMD Athlon XP 2200+
I am thinking about upgrading the CPU.
On the product page: http://www.msicomputer.com/product/p_spec.asp?model=K7N2_Delta-ILSR&class=mb
it says that it "Supports 600MHz up to Athlon™ XP 3000+ processor or higher"
What does that exactly mean?
It supports Athlon XP 3000+ but what is the "higher" processors that it can support??
??? ??? ???

Quote from: HenryW on 15-July-07, 04:29:19
CPU List HERE.
You just have to make sure you have BIOS as shown near top of list to support any 200/400Mhz FSB CPU you might get (Barton 3000+/3200+ ~ 200/400Mhz FSB). The earliest BIOS's only supported up to 166/333Mhz FSB
I'm also assuming you now have PC2100 RAM and you would also need to upgrade to either PC2700 or PC3200 depndinding on which CPU you get keeping in mind that PC3200 should also work with the 166/333Mhz CPU's
Thanks for the link.
I see that the AthlonXP 3000+ has a FSB of 166,
Higher than that there is the 3000+ and 3200+ with FSB of 200.
Now lets see if i understand correctly:
My current processor 2200+ (1.8ghz) has 133MHZ = FSB 266
The 3200+ (2.2ghz) has a 200 MHZ = FSB 400
The specifications of the board say that it supports fsb of 400 so it should work with that processor.
You say i have to upgrade the memory also?
Im using DDR333 - PC 2700 that operate at 166mhz
I need to switch to DDR400 - PC 3200 that operate at 200mhz for the 3200+ to work? Or can i still use my current memory?

What is the fastest CPU I could put in Satellite Pro L20

This is a desperate request for help!!
The Football Manager 2010 is coming out soon and my laptop needs to be up to scratch.
I know I need to upgrade it because Football Manager 2009 nearly killed it!
At the moment I have 1.4ghz Intel Celeron M chip and 704mb of ram.
What is the fastest chip I could put in? I've done a bit of research and found I can only have 2gb of ram
The laptop is in perfect working order so I don't want to buy a new one just for the sake of it and its served me well over the last 4 years - I've dropped it enough times! Just need to speed it up a bit!

Hmm... Do you really want to upgrade the pretty old Satellite Pro L20? I mean new notebooks are not so expensive anymore and I doubt that you will get a strong performance boost with new CPU.
Anyway, in your notebook is only the preinstalled CPU pretested and nobody is able to say what other CPUs will run. But you should look on the specifications for other Satellite Pro L20 notebooks. If another L20 is equipped with faster CPU, it should also work in yours. You can try it but in worst case it will not work.
Good luck!

What are the minimum CPU and Memory requirements for R12 Vision instance?

We are in the process of trying to figure out what the minimum hardware requirements are for installing the R12 Vision instance. This Vision instance would only have 5 or less concurrent users. We may have to order a new server and we are wondering what the minimum CPU and memory would be? Oracle Support will not give us this information.
We aleady know how much disk space it will need.
Dan

Hi,
See these links.
A Primer on Hardware Sizing for Oracle E-Business Suite
http://blogs.oracle.com/stevenChan/2010/08/ebs_sizing_primer.html
What Are the Minimum Desktop Requirements for EBS?
http://blogs.oracle.com/stevenChan/2010/09/ebs_pc_clients.html
Also, please see old threads for similar discussion.
Hardware Requirements
http://forums.oracle.com/forums/search.jspa?threadID=&q=Hardware+Requirements&objID=c3&dateRange=all&userID=&numResults=15&rankBy=10001
Benchmark
http://forums.oracle.com/forums/search.jspa?threadID=&q=Benchmark&objID=c3&dateRange=all&userID=&numResults=15&rankBy=10001
Thanks,
Hussein

What's the maximum cpu speed?

My KT3V manual says that I can use 2.8GHZ CPU or higher.
Mine is a 1.7GHz one.
What's the limit to the above "higher". I have heard that a friend of mine uses a KT3V with a 3.2 GHZ (the latest released by MSI)
Thanks for claryfing this to me
J. Muleto

Quote
Originally posted by maesus
your friend cheat you :P or you have taken assumption that 1.7Ghz = XP1700+, and 3.2Ghz = XP3200+, which is a WRONG assumption. :O
You are right Maesus. The technical sheet shows the Barton XP 3000+ as the maximum possible cpu to use on this board. Perhaps I was confused or my friend, I won't hear from him until the beginin of July when he comes back from L.A.
Anyway, I'm not an expert, just a single user. If in the future it MSI launches a CPU higher than 3.0+ for 166/333MHZ chipset, can I expect to use it with the K3TV or this Barton would be the latest?
Thank you for your help
J.Muleto

What is a safe CPU temp?

So I've noticed my MBA has been getting up to 90 degrees+ while gaming (I know these aren't meant for that, but hey, it works so it will). Anyway, I was wondering if such high temps was healthy and if they are okay, and if they are fine, is it healthy to have these temps for hours(Since Thursdays I game for roughtly 3-4hrs)?
P.s.
It actually gets hot enought that the metal around the WASD keys heat up, and can almost burn my figertips :s

BodomTheVixen wrote:
Thanks for the intel link, I'll be sure to watch if it goes past 100°c.
Intel's CPUs are designed to "throttle back" when they reach that temperature. Thats why the "turbo boost" speed is higher, the speed listed as its main speed is what it can run at constantly and what the cooling system is designed to handle. The "turbo boost" increases power beyond that to the CPU's full speed until the thermal limit is reached.
By increasing fan speed you will delay the time when it has to throttle, increasing long-term performance.
BodomTheVixen wrote:
Also, this isn't the first time I've seen someone say 'Speeds higher than 2000 rpm may damage your Macbook' but I'm kind of questions how exactly.
They are the same kind of people that will say "never revv your cars engine over 3000rpm when accelerating". Overly cautious because they aren't sure how it actually works.
Higher fan speeds will hurt nothing but your battery time, just as revving a cars engine will hurt nothing but fuel economy.

What settings to make cpu not use its...

Hi when I Overclock my 4690k, obviously it will run on its full speed even when at idle mode or not playing, MSI boards has this settings to make cpu not use its full power when on idle mode,, so what settings is it??? Anyone???

CPU Ratio Mode Dynamic
EIST Enabled
And As Svet said Balanced power plan

What is the best cpu for Premiere Pro and autocad?

I am considering these three cpu's. My build has to run Premiere Pro CS6 and the latest Autocad (I know this a Adobe forum, but if any out there also run Autocad in addition to PP...let me hear from you and what your build is).
I am PP hobby enthusiast/student/want to eventually have video postproduction company in future. Right now autocad is 'bread and butter' part-time.
These three are in my price range...which would you choose for PP and why? (side comments about autocad suitability also appreciated)
1. Core i7-3930K Sandy Bridge-E 3.2GHz (3.8GHz Turbo) LGA 2011 130W
2. Core i7-4770K Haswell 3.5GHz LGA 1150 84W
3. Core i7-3770K Ivy Bridge 3.5GHz (3.9GHz Turbo) LGA 1155 77W

Note that AutoCad is not an avanced software, it only uses one cpu thread (so if you have a fast solo processor that's all AutoCad makes use of) but the cpus mentioned above are the fastest cpus per single core. I don't know about the Premiere Pro i.e. what this program does in the regard of utilizing all cores and threads, but AutoCad for sure does not. So an AutoCad machine only needs a fast CPU, good memory and a graphics card that AutoCad knows how to make use of in 3D (if you are using AutoCad for 3D) but AutoCad is definitely not the program to consider for use in 3D modeling. AutoCad is still vector based program (and probably will continue to be in future, since there will always be some need for vector based design software) but Autodesk does have software that is not vector based like Inventor.

What's cooking? My CPU!!!

Similar Messages

Maybe you are looking for