What's the best forum in the UK for Sun ONE UDS

Does anyone know of a user group that meets regularly to discuss SUN ONE UDS ?in the UK ?

All printer manufacturer's play "catch-up" with OS revisions. If a printer doesn't work immediately with the latest OS, you should check the manufacturer's website. Here's a laugh: I purchased an Epson EPL-5700i monochrome laser printer a dozen years ago, for "only" $500. With all of the changes in Macs and the OS, I've never been not able to use the printer. Either Apple or the vendor has made printer driver software available seamlessly.

Similar Messages

What's the difference between Sun ONE Application Server 6 and IAS6.X

Hi, can anyone tell me what's the difference between Sun ONE Application Server6 and IAS 6.x?
Thanks a lot!

This is only the change in name from iPlanet Application Server to SunONE Application Server. Rest all is same as far as the product is concerned.

What is the recommendation for cleaning ones sensor? I have a 5D.

What is the recommendation for cleaning the sensor on the 5D III
Thank you,
M

The manual recommends using a blower when the automatic cleaning fails - or better yet, sending it to Canon for service. Sometimes - rarely - a blower will work and is the simplest and reasonably safe thing to use.
Otherwise many like the Sensor Swab solution. It is tedious and expensive, but I have used it effectively several times - especially on the 5D that seemed more prone to spots than the newer models. The problem I always have is going from bad to worse to finally better - a lot of patience is required and wasting or going through several of the swabs is not uncommon. Maybe my technique sucks, but I find it takes a lot of time and swabs to be eventually be satisfied. That said, I have never caused any damage and I have always managed to finally get the sensor clean. Along with the swabs, good lighting and magnification (reading glasses or similar) is also necessary as the spots that look huge on a photo will be nearly invisible.
http://www.sensorswab.com/
Steve
EOS 5D MKIII

Adobe X PDF files converted to jpg, edited and converted back to PDF have ragged, unclear text. I didn't have this problem with Acrobat 9 standard. What is the remedy for this. If this is the best I can expect, I won't be able to use X standard.

Adobe X PDF files converted to jpg, edited and converted back to PDF have ragged, unclear text. I didn't have this problem with Acrobat 9 standard. What is the remedy for this. If this is the best I can expect, I won't be able to use X standard.

I can't imagine any worse workflow than converting to JPEG to edit text, then back to PDF. Text in a PDF is a vector thing, smooth at all resolutions. And JPEG is made for photos. EVERY conversion to JPEG and back loses quality but how much loss there is will vary.
If you must go to an image format, try PNG.

What is the roadmap for BI-IP product w.r.t BPC

is it true that BPC will replace or serve the same function as BI-IP?
IF SO,
what is the rationale for such quick product replacement and what is the future direction for this planning product IP?
not long ago there is BW3.5 . then came BI 7 recently and that comes with IP, and now BPC in such a short span of time?
please share your views.

Hi,
First of all I would like to recommend you the relvant forum for all topics related to CPM:
You might get your answers refering to BPC and/or CPM more quickly and more precise at this forum:
Expert Forums » Business Process Expert » Corporate Performance Management
I welcome you to have a look there.
I did a quick research there and I found some information which might be interesting for you. You can find more about this at the following blog:
/people/muthu.ranganathan/blog/2007/05/22/sap-gets-serious-about-epm
Recommendations to existing customers
2007-07-10 20:35:28 Muthu Ranganathan Business Card Reply
As indicated earlier to another response in the blog, SAP would continue to support BPS,as per the existing maintenance arrangements. As of SAP NetWeaver 7.0, BI Integrated Planning (BI-IP) replaced BPS, so BPS is no longer being developed any further.Development plans for BI Integrated Planning will be unchanged by the OutlookSoft acquisition as BI-IP will continue to be SAPs long-term planning infrastructure.SAP Strategy Management is SAPs strategic nextgeneration
product in that category(scorcarding/strategy). However SAP would continue to support BSC as per the existing maintenance arrangements.
Some additional elements to each of the question:
1. Do we stop all new development in these products and start utilizing the new CPM product offerings right away?
If you already have implemented element of SEM, the maintenance allows you based on a SEM 6.0 (mySAP ERP 2005) to work on maintained product until 2013. Applications of the CPM suite are of course the recommended path for new customer, however, as each customer situation is different, I would recommend to use your local SAP contact to discuss these issues.
2. Do we continue new development in the old products and convert in the future (when the new CPM suite has stabilized and SAP has stopped further acquisitions)?
Each products of the CPM suite are now available in a stabilized and mature version, however the integration and Netweaver as a unified platform is not available. So it is more about integration than about stabilization. For more insight on the SAP roadmap again get in touch with your SAP contact.
3. Do we stop all new development in these products and use alternative SAP products like BI integreted planning, Visual composer etc. which are more mature than the new CPM products and are not scheduled for obsolesence like SEM and BPS? Then in the future we migrate to the new CPM suite when it is stabilized?
BI integrated Planning and Visual Composer are part of the technical infrastructure in Netweaver, whereas CPM elements are Application designed for performance management and with business user centric concepts. Again these products are fully matured and stabilized and the roadmap of the CPM group is to unify the technology platform and get the convergence of all Planning and Consolidation tools.
Thanks
++++++++++++
So I hope I could help you at least a bit,
Best regards,
Felix

What is the alternative for DisplayMemberPath="Value" for Windows Store applications?

I think there is a bug with Windows Store Applications when it comes to using DisplayMemberPath="Value".
Here is my code
<ComboBox Height="40" VerticalAlignment="Stretch" SelectedValuePath="Key" DisplayMemberPath="Value" x:Name="comboBox1" FontSize="25"/>
var source = new Dictionary<string, double>();
source.Add("Item1", 0.4);
source.Add("Item2", 0.3);
source.Add("Item3", 0.1);
source.Add("Item4", 0.1);
var formateDSource = new Dictionary<string, string>();
foreach (var item in source)
formateDSource.Add(string.Format("[{0}, {1}]", item.Key, item.Value), item.Key);
comboBox1.ItemsSource = source;
If you use this code in WPF in works perfectly. However if you use this code in a Windows Store Application then the Combo Box is empty and an error is thrown. So is there an alternative way to do this in Windows Store Applications and have I unearthed a
bug? Because I have researched the Web for days and found no solution to this.*please do not comment unless you have tried my code as a Windows Store App not a WPF in Visual Studios. Can Someone post an example based on my code that works in Windows Store
Apps please because this is terrible.
Thanks

It looks like you got an answer on SO:
http://stackoverflow.com/questions/29817124/what-is-the-alternative-for-displaymemberpath-value-for-windows-store-applicat
This does look like a bug.
Matt Small - Microsoft Escalation Engineer - Forum Moderator
If my reply answers your question, please mark this post as answered.
NOTE: If I ask for code, please provide something that I can drop directly into a project and run (including XAML), or an actual application project. I'm trying to help a lot of people, so I don't have time to figure out weird snippets with undefined
objects and unknown namespaces.

What are the steps for loading master data

Hello
what are the steps for loading master data? i want to learn about loading all master data and the steps to choose the best way to load the data.
if anyone has documents please send me the documents i will be really greatful
[email protected] thanks everyone
Evion

Hi Heng,
Download the data into a CSV file.
Write a program using GUI_UPLOAD to upload the CSV file and insert records.Chk the below link for example
http://www.sap-img.com/abap/vendor-master-upload-program.htm
Reward Points for the useful solutions.
Regards,
Harini.S

What are the settings for Primere Elements 9 if I've filmed with a Canon Powershot sx50 HS?

I just got this camera and I want the best quality possible. Unfortunately, it's hard for me to fully know if the settings I try create that. I get a fuzz or noise on objects like if I'm wearing a black jacket it's like static. When I put the video on my phone which is an Android Galaxy s4 it converts it into mp4 format and I get much more clear results than on my computer which perplexes me. I did a lot of trial and error with my previous camera (JVC Full HD Everio) which I got the same results. My newer Canon should be leagues ahead of the JVC, but I really can't tell as of yet. If anyone could help that would be awsome. I have examples of my trials and errors from my Youtube videos which you can see I felt I was slowly making progress with the JVC Oppositeofhood - YouTube

Opposite
Then I saw your latest post
Wait, I think I just found it. I pressed record on different settings to take pictures with like portrait to see if it would make a difference and when I uploaded them to my computer I found where it shows the BIt rate and it varied. They run at 23 frames per second 1920 x 1080 MOV video files and all the Bit rates are like 36,356 35,414 ,36,521
If your camera is recording with a variable bitrate, the Bitrate variations from file to file should not be contributing to the issue. But it does raise the issue related to whether or
not we are setting the appropriate bitrate level in the export settings. What are the units for 36,356, 35,414, and 36,517 -
kbps (also can be written Kbps) and is kilobits per second
or
Mbps which is megabits per second.
Let us try this for one of your 1920 x 1080p24 videos.
Go through the following workflow
Manually set project preset...
NTSC
DSLR
1080p
DSLR 1080p24
When you go to export your edited Timeline content, then use
Share
Computer
QuickTime
with Presets = NTSC DV 16:9 - that is going to be customized to 1080p24 (H.264.mov) under the Advanced Button/Video Tab of that preset
The essential settings under the Advanced Button/Video Tab
Video Codec = H.264
Frame Width = 1920
Frame Height = 1080
Frame Rate = 23.976
Field Type = Progressive
Aspect = Square Pixels (1.0)
Now here is where we are going to experiment....
Bitrate
Check Mark next to Limit Data Rate to and type in 36000 before kbps
note the file size of the export as well as the quality of the playback.
Repeat the whole process but in export
Remove the check mark next to Limit Data Rate. The Bitrate field will be disabled.
note the file size of the export as well as the quality of the playback.
We will be watching for your results.
Thanks.
ATR

What are the settings for the "Default Client Settings"?

What are the settings for the "Default Client Settings"? I changed them instead of creating a new policy and would like to fix that.
Thanks
James A+, Network+, MCP

Hi,
The blogs below provides the default client settings.
Default Client Settings in SCCM 2012 SP1
http://prajwaldesai.com/default-client-settings-sccm-2012-sp1-sccm-2012-sp1/
Note: Microsoft provides third-party contact information to help you find technical
support. This contact information may change without notice. Microsoft does not guarantee the accuracy of this third-party contact information.
Best Regards,
Joyce

What are the settings for apn data and mms for iphone 4 on straight talk?

what are the settings for cellular data network APN DATA and MMS for Straighttalk sims on IPhone 4?I cant send or recieve pictures.My service keeps losin signal constantly saying no service then 1 bar,2 bars,3 bars...then back down to no service.It drops calls.Iv been trying to find out the answer to this problem for 2 weeks!I have no Profile selection in my settings either to do wat its showing online on one website.and have entered numerous diffrent APNs and none have worked!!!!PLEASE HELP!!!

They're asking a question about carrier settings for their iPhone. I think that has everything to do with Apple.
Maybe they did already ask Straight Talk. I've called Straight Talk before... they're not too helpful.
You know, this forum would be much friendlier if people in this forum would quit squabbling, & posting comedic replies, not too mention name calling (like I did), when people are just needing some help.
It's also frustrating that people stick up for the guy who doesn't help, but rather takes the time to post some smart alec reply. Granted, I shouldn't have name-called... some people just frustrate me when they act like that.
Admittedly, there ARE some grey areas when it comes to carrier questions... but let the moderators do their job when someone is asking innappropriate stuff. And if the mods aren't chiming in, then that's a good indication that what the thread is about IS in fact Apple related.

What is the proceedure for replacing a hard drive (after failure) for RAID 5 with IX4-300D?

I have the IX4-300D with 4 hard drives (identical Seagate drives) using RAID 5.
Someday a hard drive will fail and I and I have to replace it. I read through the users manual briefly and I didn't see any documentation on how to perform a hard drive replacement and not lose any data.
So here are my questions:
1) I know per the instructions that Lenovo prefers using identical hard drives. Let's say in 2 years, 1 hard drive fails. Most likely, the same model Seagate hard drive will not be available. So will using a replacement hard drive by the same manufacturer with similar specifications work?
2) Will the front panel (or the software) tell me which hard drive has failed?
3) What is the proceedure for replacing a hard drive after a failure occurs? I read that the IX4-300D is not hot-swappable. So do I just power the IX4-300D down, replace the hard drive, and turn it back on?
Solved!
Go to Solution.

Hi exceptionalht,
It is best to replace the hard drive with one that is the same manufacturer, rotational speed, and capacity, so it does not have to be exactly the same model.
The front panel should show which drive has failed. If not you can check the web interface to find out.
That is the basic procedure for replacing a hard drive. You can see a more detailed instructions here: Installing hard drives in an ix4-300d
Have questions and need answers?
Search the database for answers to FAQ's, software/driver downloads, tutorials, news, features and more!
LenovoEMC Support & Downloads
LenovoEMC North America Support Contact Page

Illustrator keeps quitting-notice others have had similar issues, not resolved-so what it the reason for "sending a report" to Adobe if nothing can be done with it????? paying for a product that I can't use when I need to use it and no help-come on-someon

Illustrator keeps quitting…notice others have had similar issues…so what it the reason for "sending a report" to Adobe if nothing can be done with it????? paying for a product that I can't use when I need to use it and no help…come on…someone has to have an answer…HELP Pleeeeease

<moved from Adobe Creative Cloud to Illustrator>
reset your preferences -
acrobat: http://help.adobe.com/en_US/acrobat/X/pro/using/WS58a04a822e3e50102bd615109794195ff-7feb.w .html
adobe media encoder: https://forums.adobe.com/thread/1713540
after effects: http://helpx.adobe.com/after-effects/using/preferences.html
dreamweaver: https://helpx.adobe.com/dreamweaver/kb/restore-preferences-dreamweaver-cs6-cc.html
flash: http://helpx.adobe.com/flash/kb/re-create-preferences-flash-professional.html
illustrator: http://helpx.adobe.com/illustrator/using/setting-preferences.html
indesign: https://forums.adobe.com/thread/526990
lightroom: https://helpx.adobe.com/lightroom/help/setting-preferences-lightroom.html
muse (mac): https://forums.adobe.com/thread/1246022?tstart=0
photoshop: https://forums.adobe.com/thread/375776
photoshop elements: https://helpx.adobe.com/photoshop-elements/kb/preference-file-locations-photoshop-elements .html, http://www.photokaboom.com/photography/learn/Photoshop_Elements/troubleshooting/1_delete_p references_file.htm
premiere elements: https://helpx.adobe.com/photoshop-elements/kb/preference-file-locations-photoshop-elements .html
premiere pro: http://www.mediacollege.com/adobe/premiere/pro/troubleshooter/trash-preferences.html
if that fails, uninstall, clean (http://www.adobe.com/support/contact/cscleanertool.html) and reinstall

What are the tables for documents in PP Orders

Hi all,
What are the tables for Document Items (type D) in PP orders ?
Regards,
Magda

Welcome to SCN, please refer to the rules of engagement, link at the top of every forum, please search before asking basic questions.
Thread locked.
Thomas

In BSP-HTMLB what is the code for auto refresh.?

Hi friends,
In BSP-HTMLB what is the code for auto refresh.?
Means i gave the input every 2 minutes once my output should get refresh.
So what is the code in bsp-htmpb?
Moosa

Hi Moosa,
Many threads on this topic...
[Auto Refresh - I|Auto refresh]
[Auto Refresh - II|Auto-Refresh for BSP page]
[Auto Refresh - III|Page refresh.....]
Search the forum for more information.
Regards,
Anubhav

Can I migrate from WCS 7.0 to PI 1.2. If so, what are the guidelines for migration?

Can I migrate from WCS 7.0 to PI 1.2. If so, what are the guidelines for migration? Do we have any Instructions/steps?

Migration from WCS 7.0 to PI 1.2 can be performed. If the customer wants to migrate data you need to first upgrade to NCS 1.1.1 You can download NCS 1.1.1 from Cisco.com if you have a valid service contract.
For the migration step involving NCS an evaluation license is sufficient. You can obtain an NCS evaluation license from http://www.cisco.com/go/license > Get Demo > Network Mgmt Products > Cisco Prime NCS Evaluation License.
Instructions for migrating data from WCS 7.0 to NCS 1.1.1 are available in NCS 1.1.1 Release Notes. Do not upgrade to NCS 1.1.2 as this release is not upgradeable to Prime Infrastructure 1.2. If you are ordering a Cisco Prime physical appliance (PRIME-NCS-APL-K9) be sure to select the NCS 1.1 image which you can later upgrade to Prime Infrastructure 1.2 after you have migrated your WCS data.
There is a post in the support forum which can be refered.
https://supportforums.cisco.com/docs/DOC-26972

What's the best forum in the UK for Sun ONE UDS

Similar Messages

Maybe you are looking for