What's the proper behavior of Standard ACLs?

Hi, I have a question regarding the Standard ACL.
If I have 1000 lines of ACEs in an standard ACL, and I remove one ACE from the standard ACL, should this ACL be completely gone? Or we should have the rest of 999 ACEs still there?
Thanks!

Ok. So you want to remove ONE (or more) selected offending line from your ACL. Let's take your example:
access-list 10 deny 130.0.0.1
access-list 10 deny 120.0.0.1
access-list 10 deny 130.0.1.1
access-list 10 permit any
Let's say you want to remove "access-list 10 deny 130.0.1.1". Cut-n-paste your original ACL into a Wordpad or Notepad and you'll wind up with something like this:
conf t
no access-list 10
access-list 10 deny 130.0.0.1
access-list 10 deny 120.0.0.1
access-list 10 permit any
end
wr
Cut-n-paste everything back into your ACE.

Similar Messages

What is the proper way to publish standard proxies/services using PI?

Hello experts,
Iu2019m working on a Project where we have an ECC 6.0 and we need to publish some standard services to external third-party applications. We found that the functionality that these third-party applications need is accomplished by the service MaintenanceRequestCreateRequestConfirmation_In of component ESA ECC-SE 603. As we are centralizing all our interfaces in SAP Process Intregration I have installed the ESA ECC-SE 603 XI content in SAP PI. After the installation, in tr. SPROXY transaction of the ECC system I can see the proxy properly implemented and ready to be called. And now I have to configure the interface in Integration Directoy. What I wonder is whatu2019s the best practice to configure this in PI? As I can see in ESR the service category is Inbound but, if Iu2019m not wrong, I have to publish a Outbound service? What should I do? Copy the entire definition to my own Software Component and create my own Outbound service? What is the proper way to publish standard proxies/services using PI?
Thank you in advance.

Using the Page Items to Submit property on the report region, the Refresh action is all that should be needed. I created a copy of page 2 on page 3, removed the Set Value action, and it is working as expected. I don't have access to 4.2.1 to try it on that specific patch level, but I've been using Page Items to Submit with a Refresh DA since 4.2.0 with no problems.

What Are The Proper Settings In Audio/MIDI Setup?

In the Audio Input, Line In, what is the proper setting for Hz? 44100, 48, 96, And should the 2ch be 16bit, 20bit or 24 bit? Right now I'm using an older gray iMic as the Audio in
Thanks

Steve B5 wrote:
what is the proper setting for Hz?
44100
And should the 2ch be 16bit, 20bit or 24 bit?
16 is standard, 24-bit (new to GB4) is the highest resolution

What is the proper way to change rowHeight? (possibly animate?)

What is the proper way to change rowHeight for UITableView? I set tableView.rowHeight and do a [tableView reloadData]. Is this necessary? Also, is it possible to animate the height change? It is not a standard transition.

Not a perfect solution for your animation question - but....
in the function where you want to change the height
WARNING PSUDO CODE
//indexPath is the path for theCell you want to edit
thePlaceThatYouStoreYourHeights[x] = aNewHeight;
[tableView deleteRowsAtIndexPaths:[NSArray arrayWithObject:indexPath] withRowAnimation:UITableViewRowAnimationFade];
[tableView insertRowsAtIndexPaths:[NSArray arrayWithObject:indexPath] withRowAnimation:UITableViewRowAnimationTop];
and inside of - (CGFloat)tableView:(UITableView *)tableView heightForRowAtIndexPath (NSIndexPath *)indexPath
return thePlaceThatYouStoreYourHeights[indexPath.row];
Basic flow
1. Store new desired height somewhere
2. Remove the cell deleteRowsAtIndexPaths
3. UITableView paints the animation for the "remove" transition **see note
4. Re-add the cell insertRowsAtIndexPaths (which subsequently kicks of a call to heightForRowAtIndexPath before animating)
5. UITableView paints the animation for the "add" transition
You do NOT need to call reloadData to get this to work.
**note: an enum such as UITableViewRowAnimationNone does not exist (it should but it doesnt seem to). the docs for InsertRowsAtIndexPaths say "A constant that either specifies the kind of animation to perform when inserting the cell or requests no animation." however there are only 5 items in the UITableViewRowAnimation enum and UITableViewRowAnimationFade resolves to 0 - so passing NO will actually get you fade. Nor will it take nil.
Hope this helps shed some light.

My calendar date is not automatically changing, what's the proper setting?

My calendar date is not automatically changing, what's the proper setting?

If the population of the ObservableList (independent of any UI considerations takes a long time, then you probably want to do the populations off the JavaFX application thread (e.g. via a javafx.concurrent.Task)).
If you do populate the list in a Task, standard threading cautions apply in terms of not updating items in the scene graph off the JavaFX application thread and ensuring that the system is absent of race conditions, etc.
Look over the documentation of http://docs.oracle.com/javafx/2.0/api/javafx/scene/control/Cell.html and that may help you.
The JavaFX controls such as ListView have been carefully designed to exhibit high performance even when backed by extremely large lists (through the concept of virtualization explained in the Cell documentation). For example, if the backing list is updated but the portion of the list being updated is not within the currently displayed list contents, (I would hope) the update would be very efficient.

How can I use 2 Apple IDs in Itunes? I have 2 IOS Devices. They each have there own AppleID. What is the proper way to sync both of them to Itunes?

How can I use 2 Apple IDs in Itunes? I have 2 IOS Devices. They each have there own AppleID. What is the proper way to sync both of them to Itunes? I wanted my teenager's AppleID to be different from mine so that she couldn't charge stuff to my AppleID, therefore I created me another one. Now when I go to Sync either device, it tells me that this IOS device can only be synced with one AppleID. Then I get a message to erase it, not going to do that, lol. If I logout as one ID and login as the other, will it still retain all synced information on the PC from the first IOS device? If I can just log in out of the AppleID, then I have no problem doing that as long as the synced apps, music, etc stays there for both. I am not trying to copy from one to the other, just want to make sure I have a backup for the UhOh times. If logging in and out on the same PC of multiple AppleIDs is acceptible then I need to be able to authorize the PC for both devices. Thanks for the help. I am new to the iOS world.

"Method Three
Create a separate iTunes library for each device. Note:It is important that you make a new iTunes Library file. Do not justmake a copy of your existing iTunes Library file. If iTunes is open,quit it.
This one may work. I searched and searched on the website for something like this, I guess I just didn't search correctly, lol. I will give this a try later. My daughter is not be back for a few weekends, therefore I will have to try the Method 3 when she comes back for the weekend again. "
I forgot to mention that she has a PC at her house that she also syncs to. Would this cause a problem. I am already getting that pop up saying that the iPod is synced to another library (even though she is signed in with her Apple ID to iTunes) and gives the pop up to Cancel, Erase & Sync, or Transfer Purchases. My question arose because she clicked on "Erase & Sync" by mistake when she plugged the iPod to her PC the first time. When the iPod was purchased and setup, it was synced to my PC first. When she went home, she hooked it up to her PC and then she erased it by accident. I was able to restore all the missing stuff yesterday using my PC. However, even after doing that it still told me the next time I hooked it up last night that the iPod was currently synced with a different library. Hopefully, you can help me understand all this. She wants to sync her iPod and also backup her iPod at both places. Both PCs have been authorised. Thanks

What is the proper way to record line numbers in Master/Detail records?

Guys and Gals,
Been thinking about this for awhile, but thought it best to ask the people who really know what they are doing.
What is the proper way to record & show line numbers in a Master / Detail record set?
For example, take Master/Detail relationship Orders and OrderItems. Orders has a column Document_Number and OrderItems has Document_Number, Line_Number. Line_Number should contain the row number 1,2,3,4 ... etc. for each row in a document.
Should I ...
<ol><li>Add a sequence and a trigger in the database? The FusionOrderDemo does this, but then the sequence never "resets" and I've got row numbers that keep incrementing. So one document has rows 4,5,6 and the next document has 7,8,9 when they should both have 1,2,3.</li>
<li>Programmatically take care of the row numbers? This seems like I'm asking for trouble. Anytime an insert or delete operation gets done, I'll have to iterate through rows and re-assign row numbers.</li>
<li>Is there a way to assign row numbers in a table iterator (or data collection?) to an entity?</li></ol>
Any suggestions would be appreciated. It's looking like #2 is my only option, but if anyone knows different I'd love the input.
Will

Thank you both guys.
As John said, I believe I'm looking for a gap-free sequence per master record.
The line number of the OrderItems table is the second half of the primary key. The first half of the primary key (DocumentNumber) is the foreign key to the Orders table.
Think of it like line items on an order or invoice. For example, if you were talking to someone on the phone concerning an invoice, you might say, "The pricing for line item #3 is incorrect." In this case, it's good to have a common reference. Or imagine a Microsoft Excel spreadsheet with no row numbers displayed! You'd never get anywhere if you had to explain something over the phone.
If this is tricky to perform, I take it using a sequence and trigger such as the Fusion Order Demo is the best way to approach the challenge for simplicity's sake?
Will

Need to convert mini dvi to s video to run a school's Hatiachi ceiling mount projector. What is the proper adapter?

Need to convert mini dvi to s video to run a school's Hatiachi ceiling mount projector. What is the proper adapter?

Check the projector and see what kind of input is has, most have a VGA connector, so you would need a male to male VGA. You will also need the Mac mini dvi to male VGA (of course).
Some of the older projetors have a component in only, which is the red,yellow,green, RCA connectors, which are avaialable. (Usually the are fairy short, 5 ft or so, so you would need to get a VGA with yhe mini DVI to VGA, and a component (the one with the 3 RCA's) you will probaly have to get a Female to Female VGA adapter to connect te VGA to the component.
And finaally if that weren't enough, the really old projectors have only a composite input. All I can say about that is "the hunt is on"
Best of luck

What is the proper way to close all open sessions of a NI PXI-4110 for a given Device alias?

I've found that, when programming the NI PXI-4110 that, if a the VI "niDCPower Initialize With Channels VI" (NI-DCPower pallette) is called with a device
alias that all ready has one or more sessions open (due to an abort or other programming error) a device reference results from the reference out that has a (*) where "*" is post-fixed to the device reference where and is an integer starting that increments with each initialize call. In my clean up, I would like to close all open sessions. For example, let's said the device alias is "NIPower_1" in NI Max, and there are 5 open sessions; NIPower_1, NIPower_1 (1), NIPower_1 (2), NIPower_1 (3), and NIPower_1 (4). A simple initialize or reset (using niDCPower Initialize With Channels VI, or, niDCPower Initialize With Channels VI, etc.) What is the proper way to close all open sessions?
Thanks in advance. Been struggleing with this for days!

When you Initialize a session to a device that already has a session open, NI-DCPower closes the previous session and returns a new one. You can verify this very easily: try to use the first session after the second session was opened.
Unfortunately, there is a small leak and that is what you encountered: the previous session remains registered with LabVIEW, since we unregister inside the Close VI and this was never called. So the name of the session still shows in the control like you noted: NIPower_1, NIPower_1 (1), NIPower_1 (2), NIPower_1 (3), and NIPower_1 (4), etc.
There may be a way to iterate over the registered sessions, but I couldn't find it. However, you can unregister them by calling "IVI Delete Session". Look for it inside "niDCPower Close.vi". If you don't have the list of open sessions, but you have the device name, then you can just append (1), (2) and so forth and call "IVI Delete Session" in a loop. There's no problem calling it on sessions that were never added.
However - I consider all this a hack. What you should do is write code that does not leak sessions. Anything you open, you should close. If you find yourself in a situation where there are a lot of leaked sessions during development, relaunching LabVIEW will clear it out. If relaunching LabVIEW is too much of an annoyance, then write a VI that does what I described above and run it when needed. You can even make it "smarter" by getting the names of all the NI-DCPower devices in your system using the System Configuration or niModInst APIs.
Hope this helps.
Marcos Kirsch
Principal Software Engineer
Core Modular Instruments Software
National Instruments

What is the expected behavior in a zone after adding a new static route in Solaris 10....

Hi Folks,
I have a few Solaris 10 production machines here at work and had a strange thing happen. I added a new route to these machines using the "add route <destination > <gateway>" command and my web applications running in the zones on these machines froze up. The applications that froze had no reason to do this as they have never talked to the machine in this new route. Here is the old route table via netstat -rn:
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface
172.23.248.0 172.23.248.24 U 1 6794 bge1
204.154.126.0 172.23.248.100 UG 1 0
204.154.127.0 172.23.248.100 UG 1 0
204.154.134.0 172.23.248.100 UG 1 0
204.154.135.0 172.23.248.100 UG 1 0
204.154.132.0 172.23.248.100 UG 1 0
204.154.133.0 172.23.248.100 UG 1 0
204.154.130.0 172.23.248.100 UG 1 0
204.154.131.0 172.23.248.100 UG 1 0
204.154.128.0 172.23.248.100 UG 1 0
204.154.129.0 204.154.129.74 U 1 7980 bge0
204.68.180.0 172.23.248.100 UG 1 0
204.68.181.0 172.23.248.100 UG 1 0
192.168.0.0 172.23.248.100 UG 1 34
172.28.0.0 172.23.248.100 UG 1 9
172.29.0.0 172.23.248.100 UG 1 0
172.30.0.0 172.23.248.100 UG 1 0
172.31.0.0 172.23.248.100 UG 1 0
172.24.0.0 172.23.248.100 UG 1 0
172.25.0.0 172.23.248.100 UG 1 44
172.26.0.0 172.23.248.100 UG 1 934
172.27.0.0 172.23.248.100 UG 1 0
172.20.0.0 172.23.248.100 UG 1 0
172.21.0.0 172.23.248.100 UG 1 0
172.22.0.0 172.23.248.100 UG 1 82
172.23.0.0 172.23.248.100 UG 1 161975
172.16.0.0 172.23.248.100 UG 1 0
172.17.0.0 172.23.248.100 UG 1 0
172.18.0.0 172.23.248.100 UG 1 0
172.19.0.0 172.23.248.100 UG 1 82
10.0.0.0 172.23.248.100 UG 1 1766
224.0.0.0 204.154.129.74 U 1 0 bge0
default 204.154.129.1 UG 1 8411
127.0.0.1 127.0.0.1 UH 225713773 lo0
Here is the route table after I added my one additional route (note the top line):
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface
204.154.129.209 172.23.248.100 UGH 1 5
172.23.248.0 172.23.248.28 U 1 5757 bge1:3
204.154.126.0 172.23.248.100 UG 1 0
204.154.127.0 172.23.248.100 UG 1 0
204.154.134.0 172.23.248.100 UG 1 0
204.154.135.0 172.23.248.100 UG 1 0
204.154.132.0 172.23.248.100 UG 1 0
204.154.133.0 172.23.248.100 UG 1 0
204.154.130.0 172.23.248.100 UG 1 0
204.154.131.0 172.23.248.100 UG 1 0
204.154.128.0 172.23.248.100 UG 1 0
204.154.129.0 204.154.129.86 U 1 484 bge0:2
204.68.180.0 172.23.248.100 UG 1 0
204.68.181.0 172.23.248.100 UG 1 0
192.168.0.0 172.23.248.100 UG 1 114
172.28.0.0 172.23.248.100 UG 1 2
172.29.0.0 172.23.248.100 UG 1 0
172.30.0.0 172.23.248.100 UG 1 0
172.31.0.0 172.23.248.100 UG 1 0
172.24.0.0 172.23.248.100 UG 1 0
172.25.0.0 172.23.248.100 UG 1 43
172.26.0.0 172.23.248.100 UG 1 944
172.27.0.0 172.23.248.100 UG 1 0
172.20.0.0 172.23.248.100 UG 1 0
172.21.0.0 172.23.248.100 UG 1 0
172.22.0.0 172.23.248.100 UG 1 77
172.23.0.0 172.23.248.100 UG 1 160823
172.16.0.0 172.23.248.100 UG 1 0
172.17.0.0 172.23.248.100 UG 1 0
172.18.0.0 172.23.248.100 UG 1 0
172.19.0.0 172.23.248.100 UG 1 0
10.0.0.0 172.23.248.100 UG 1 183
224.0.0.0 204.154.129.86 U 1 0 bge0:2
default 204.154.129.1 UG 1 1850
127.0.0.1 127.0.0.1 UH 58 225894 lo0:3
My question is why did my application die and need to be restarted after this one simple route was added? What is the expected behavior in a zone after adding a new route to the root zone?
Thanks,
Tom Gellert
tom.gellert@tellabs.com

Greg- Dreamweaver CS4/Live View integration with BrowserLab allows you to send interactive states of a local site/design directly to BrowserLab (dynamic data, rollover/mouse interaction states, widget states, et al), and from behind firewalls no less- definitely a scenario we covered. You can get the extensions (which require Dreamweaver CS4, of course) up on the Labs site: http://labs.adobe.com/technologies/browserlab/

What's the proper protocol for a reset on my ipod touch 4g? iOS 6 has totally jacked it up and it will no longer do anything but crash, and won't sync with itunes wirelessly or by cable.

What's the proper protocol for a reset on my ipod touch 4g? iOS 6 has totally jacked it up and it will no longer do anything but crash, and won't sync with itunes wirelessly or by cable.
It's a 64G ipod touch and was fine till Apple told me to upgrade to ios 6. Now most of my apps crash, my music won't play and I just get a white screen when I hit Music.
When I try to sync to itunes it acts like it's going to sync and appears to recognize the ipod, but it's grayed out and has an update circle by it that spins for a while until itunes eventually freezes alltogether. Is there a way to go back to ios 5 after a erase and reset?

iOS: Unable to update or restore

What Is The Proper J2EE Architect For This National Defense Project?

A brief description of a national defense project I am looking into is that the system being developed is supposed to verify the "smartcard" of the card holder and his/her fingerprints against the Defense Department database. The system also reads in information about people (facial features, height, weight, etc.) and stores the information in the database, and then issues new "smartcard".
1. People involved in the project already decided to use swing for the client tier.
2. The problem is the Defense Department database. It is a flat file database and this database cannot be touched. It is a black box for Java developers. The Defense Department may provide a jar as an outer layer of this database.
Question 1: Is the web tier essential for this defense project?
Question 2: What is the proper J2EE architect for this project?
Question 3: How to deal with the data problem? Especially it looks that entity beans are not applicable.
Question 4: How does the system handle very heavy load? It is possible that tens of thousands of people will use the system at the same time.

A brief description of a national defense project I am
looking into is that the system being developed is
supposed to verify the "smartcard" of the card holder
and his/her fingerprints against the Defense
Department database. The system also reads in
information about people (facial features, height,
weight, etc.) and stores the information in the
database, and then issues new "smartcard".
1. People involved in the project already decided to
use swing for the client tier.
2. The problem is the Defense Department database. It
is a flat file database and this database cannot be
touched. It is a black box for Java developers. The
Defense Department may provide a jar as an outer layer
of this database.
Question 1: Is the web tier essential for this defense
project?
Question 2: What is the proper J2EE architect for this
project?
Question 3: How to deal with the data problem?
Especially it looks that entity beans are not
applicable.
Question 4: How does the system handle very heavy
load? It is possible that tens of thousands of people
will use the system at the same time.
Hi,
You can get it done here :http://www.thesoftwareobjects.com

What is the proper procedure to backup to multiple external hard drives if one wishes to rotate drives such that you may store one in a fire safe?

Description: If I want to back up to two external hard drives using Time Machine, what is the proper procedure to follow such that I could keep one attached to Time Machine for daily backups, and one that I attach monthly such that I can back it up monthly, and then store it in a fire safe. To do this, what are the exact steps to follow?
Research in Progress:
I selected the "?" icon in Time Machine which took me to "Mac Help - Time Machine Preferences" section. I reviewed this section, including the "Select Backup Disk, Select Disk, Add or Remove Backup Disk." It says, "If you haven’t set up Time Machine, click Select Backup Disk to set up a backup disk. Repeat the steps for each backup disk you want to set up." I did add two backup disks. It goes on to say "If you already set up Time Machine, your backup disks are listed, and information about each backup disk is shown. To select, add, or remove backup disks, click Select Disk or Add or Remove Backup Disk." Well, what is lacking here is what happens when you "Remove" the backup disk.
As I have read this section, it raises additional questions:
What are some cautionary statements.
What happens after you remove a backup disk? Will Time Machine recognize it later?
What is the proper procedure for removing and ejecting one of your external hard drive when you use it with Time Machine? What happens if you don't "remove" a backup drive and instead just drag it to the "trash can, i.e. eject it" and later reconnect it.?

Time Machine supports multiple backup drives including network area storage volumes (NAS) as well as physically-connected external backup drives.
In , System Preferences, Time Machine, add the second drive by clicking Select Disk.
All available connected drives including connected network drives are displayed.
Select the additional drives, one at a time.
Connected Network drives are displayed on the desktop only when actively being used by Time Machine for backup.
When prompted, select 'use both' when adding the second drive.
Then choose Select or Remove at the bottom of the list of available devices and network volumes to add additional drives.
Time Machine then automatically rotates backups among the available designated devices and volumes.
If the drive is physically not present, Time Machine skips to the next available backup drive.
To DISMOUNT a drive to take it off-site, it is NOT necessary to remove it from the Time Machine preferences.
When the drive is NOT in use, dismount it by Command+clicking that Drive icon on your desktop (or in Finder) and then "Eject".
That's it.
After 10 days with no backups to a given device, Time Machine does display a message and (as I recall) asks if you want to remove that drive from the rotation.
You can never be too rich or have too many backups!

What is the proper way to charge battery in 2012 15 inch macbook pro.

what is the proper way to charge the battery and make it last longest

About Batteries in Modern Apple Laptops
Battery University
Apple - Batteries - Notebooks
Apple - Batteries
Extending the Life of Your Laptop Battery
MacBook and MacBook Pro- Mac reduces processor speed when battery is removed while operating from an A-C adaptor
Apple Portables- Calibrating your computer's battery for best performance
Mac notebooks- Determining battery cycle count

What is the expected behavior in iOS 7 when hitting send on an email with no wifi or cell connection being present?

What is the expected behavior in iOS 7.x when hitting send on an email with no wifi or cell connection being present? Also is the behavior designed to be any different if the user intiates airplane mode ahead of time?
We have a couple of users that claim in this situation the email will act like it sent in which they expect it will go out once a network connection is restored. They then come to find the recipient never recieved it and that it does not show in sent email. Its merely lost and they claim its also not in drafts.
I would hope the expected behavior would be that it would either retry sending once network connectivity is restored or at least warn that it needs to be saved as a draft since no connection is present.

It should show "X unsent messages" at the bottom of the mail app.
It also should create an outbox where the unsent emails will queue up, but this could also vary on the email provider.
Once you re connect to a network, it should just send the messages

What's the proper behavior of Standard ACLs?

Similar Messages

Maybe you are looking for