WHAT SHOULD I DO MORE TO GET MY FILES BACK IN THE FCP FORMAT ?
A ROUND-ABOUT PROBLEM
RECENTLY I GRADUATED FROM. FCE AND FCE HD. I DECIDED TO INSTALL FCP 5. I HAVE POWER BOOK G4 V10.4.8, PROCESSOR 1.5 GHZ PC SDRAM WITH INTERNAL MEM 80 DISK STORAGE AND 1 GB DDR SDRAM. I ALSO HAVE AN EXTERNAL LaCIE WITH 200 CAPACITY.
IN THE PROCESS OF INSTALLING FCP, THE STUPID THING I DID WAS TO CHANGE NAME OF THE MEDIA FILE, AND THIS ACTION CAUSED ALL MY FILES GO OFFLINE. THE OPTIONS GIVEN TO ME BY THE RECONNECT FILLES TABLE BOX TO GET BACK MY FILES ARE:I TRIED TO USE BOTH BUT WITH NO SUCCESS.
I WOULD BE GRATGEFUL TO ANY ONES WHO COULD HELP ME RECOVER MY FILES WITHOUT GOING INTO THE PAIN OF CAPTURING THEM FROM TAPE.
FOR THOSE OF YOU WHO HAVE THE PATIENCE PLEASE READ MOR BELOW. THANK YOU SO MUCH.
WHEN I TRY I GET A WARNING WHICH SAYS:
THE FILE FORMAT OF THIS PROJECT IS FROM AN EARLIER VERSION. WOULD YOU LIKE TO UPDATE THIS PROJECT?
NOTE: ONCE SAVED, THIS FILE CANNOT BE OPENED BY PREVIOUS VERSION. TO AVOID OVERWRITING THE ORIGINAL PROJECT FILE , YOU CAN CHOOSE SAVE PROJECT AS FROM THE FILE MENU WHEN PROJECT UPDATING IS COMPLET
WHEN I SAY YES, ANOTHER BOX APPEARS: UPDATE PROJECT. IT SAYS THE FOLLOWING:
THIS PROJECT CONTAINS ONE OR MORE SEQUENCES WHICH THIS VERSION OF FINAL PRODUCT PRO CAN RENDER WITH MOTION TAP QUALITY(NAMELY SCALIBG, ROTATION, ETC). PLEASE CHOSE A SCALING QUALITY TO USE (“FASTEST” RECOMMENDED IS THE QUALITY LEVEL 4.5.
NEW QUALIT Y CHICKED INSIDE THE BOX ARE: BEST, NORMAL, FASTEST OR LINEAR . THE UNCHECKED LITTLE BOX READS: REMOVE EXISTING FILES (THIS ACTION IN NOT UNDOABLE
WHEN I PRESS OK “OFFLINE FILES” BOX APPEARS AND SAYS:
SOME OF THE MEDIA OF YOUR PROJECT REFERENCES EITHER CHANGED, MOVED, OR GONE AWAY.YOU CAN EITHER RECONNECT THESE FILES , OR CONTINUE WITH THEM BEING OFFLINE. BELOW THIS SAYS AS FOLLOWS:
FORGET FILES. BELOW THAT THERE IS AN UNCHED BOX WHICH SAYS: MEDIA FILES 69 OFFLINE
WHEN I PRESS CONNECT INSTEAD OF CONTINUE , THE RECONNECT FILLES BOX OPENS AND 69 OFFLINES FILES APPEAR. IN THIS RECONNECT FILES BOX THERE ARE 2 SECTIONS
THE 1ST SECTION HAS A LITTLE UNCHECKED SKIP FILE BOX AND ANOTHER LITTLE CHECKED BOX WHICH READS: SEARCH SINGLE LOCATION. WHEN I OPEN IT TWO OPTIONS ARE GIVEN AS FOLLOWS:
MACINTOSH HD: USERS WITH MY NAME AND DOCUMENT
LaCILE:FINAL CUT PRO DOCUMENTS; AUTO SAVE VAULT WITH THE TITLE OF MY FILE
WHEN I PRESS RECONNECT I GET THE FALLOWING PATH :
MY NAME.>MACINTOSH HD >APTS FCT 5 >GRAY FILES
WHEN I CHANGE THE SHOW BOX TO REVEAL FILES .I GET OFFLINE
WHEN I ADD RESEACH, IT TAKES ME TO THE A CHOOSE A FOLDER WITH THE FOLLOWING PATH:
MY NAME>LACIE DISK>FINAL CUT DOCUMENT >FOLDER >GRAY FILES WHICH CANNOT BE RVEALD., AND WHICH I CANNOT CHOOSE. IT GOES ON AND ON IN A CIRCLE WITHOUT HELPING ME TO GET MY FILES IN FCP FORMQAT.
WHAT SHOULD I DO MORE TO GET MY FILES BACK IN THE FCP FORMAT WITHOUT BEING STUCK TO OFFLINE FILES FOR EVER? YOUR STEP BY STEP TO WALK ME THROUGH TO REESTABLISH MY FILES WOULD BE GREATLY APPRECIATED.
A round-about problem
I thank you all for your very kind replies. I have rewritten my issue in lower case as suggested by all of you. I hope I will be helped.
Recently, I thought I had graduated from final cut express and final cut express HD when . I decided to install final cut pro. Perhaps a wishfull thinking!
I have a power book g4 v 10.4.8, processor 1.5 ghz sdram with internal memory of 80 storage disk and 1 gb ddr sdram. I also have an external LaCie with a 200 storage capacity.
In the process of installing final cut pro, I stupidly changed the name of the media file. Maybe this action caused all my clips, video and audio, files go offline. The options given to me by the Reconnect Files Table , to get my files back, are : Single Search Location and Search.
I tried and tried both with no success. I would be grateful to any ones who might be able to help me to recover my clips without going through the pain of recapturing them from the tape. There are several tapes to be recaptured.
Now, for those of you who may have the patience, please read more below to see what I have gone through.
When I try to get to the files, I get the first warning: “The file of this project is from an earlier version. Would like to update this project?” And then it continues: “Note, once saved, this file cannot be opened by previous version. To avoid overwriting the original project file , you can choose Save Project As from the File Menue when the project updating is complete”. (It was at this point where I changed the files names formatted by the previous versions).
When I say Yes, another box appears: Update Project. It reads as follows:
“This project contains one or more sequences which this version of Final Cut Pro can render with Motion Tap (i.e. scalable, rotation, etc). Please choose a scalable quality (“fastest” recommended is the quality level 4.5. New Quality checked inside the little Box are: Best. Normal Fastest or linear." I choose Normal. The unchecked little Box reads: "Remove existing files ( this action is not undoable, it says”.
(By the way, in my project no sequences, have been set up as yet; they are all clips inside the bins with red slash in all clips).
When I press OK, “Offline Clips” Box opens and says the following:
“Some of the media of your project references either changed, moved, or gone away. You can either Reconnect these files, or Continue with them being Offline”. Below this it continues:
“Forget files.” Below that there is an unchecked box which says: “Media Files 69 Offline”.
When I press Connect instead of Continue, the Reconnect Files Box opens with 69 Offline files. In this Reconnect Files Box there are two sections’
The first section has a little unchecked Skip Files Box and another little checked Box which reads: “Search Single Location”.
When I open it, two paths are given to recover my files:
My name>LaCie> Final Cut Document>Folder>Gray files which cannot be revealed, and which I cannot open. I go on and onl ike a checken without a head in a circle without being able to get to the files off Offline.
I have the same problem with the second path: My name>Macintosh HD>FCP 5>gray files.
What should I do more to get my clip files back in the FCP format without being stuck to Offline files for ever?
I am new to this field and enjoy what I am doing. I am old, and sometime my head goes off. Your expert step by step walking me through to reestablish my file linkage with Media would be greatly appreciated. Thank you all and have a nice holiday. Faruk Sabet
Similar Messages
-
What do I do when I get my iPhone back from the repair center?
What do I do when I get my iPhone back from the repair center?
If it was replaced then you should be able to restore a back up of your phone
iTunes: Backing up, updating, and restoring iOS software
If you received a note it will tell you what they found and why they could not repair. It depends on the situation -
What should I do when I get failure to instal error message?
what should I do when I get a failure to install error message?
Could you please provide some more details like Product you are installing, OS details etc.
-
Hello. I ve got a question. I accidentally bought membership but it doesnt have Adobe Muse that I need. What should I do? Can I extend my membership for the right one, or should I first get the money back. What kind of membership do I need to have Adobe Muse software?
Plans are listed at Creative Cloud pricing and membership plans | Adobe Creative Cloud
The drop down at individual plans does show that you may subscribe to only Muse
You probably need to cancel what you have... You need Adobe support to cancel a subscription
-start here https://forums.adobe.com/thread/1703848
-or by telephone http://helpx.adobe.com/x-productkb/global/phone-support-orders.html
--and two links which may provide more details, if the above links don't help you
-http://helpx.adobe.com/x-productkb/policy-pricing/return-cancel-or-change-order.html
-http://helpx.adobe.com/x-productkb/policy-pricing/cancel-membership-subscription.html -
My backup got interrupted and now when I try to backup I get the following message: The backup disk image “/Volumes/Data/Macintosh.sparsebundle” is already in use. What should I do so that I can start backing up again?
1. Restart your MBP and try the back up again. If this fails try step #2 below
2. Unplug your Time Capsule from the AC giving it thirty seconds or so to discharge, plug it back in and retry the back up again once you're back online.
3. if step #1 and #2 fails, go here:
http://pondini.org/TM/C12.html -
what should I do when I get this message ? (NSURLErrorDomain error -3001.)(102)
Many poeple has the same problem. All you have to do is download and istall this update manually from here: http://swcdn.apple.com/content/downloads/53/02/041-8081/2jwp4wjrwygtm4lc608qy4h0 n4a9yyq37g/Safari6.0.2Mountain.pkg
Hope this helps! -
What should I trust more when it comes to preparing a project for DVD (exporting a timeline to Compressor then using DVD Studio Pro)?
My bars look fine on the internal waveform and vectorscope. So does the image. (And everything looked fine when I captured the footage on an external waveform/vectorscope).
When I play a burned DVD, all the levels (blacks and whites) are low on my home 1080p LCD (the DVD is SD, anamorphic).
When I play the DVD on 4 different consumer CRTs and LCDs, the image looks very close to what FCP shows on the computer screen.
At work, when I play the DVD through an SDI framesync, through a Sony 8000 switcher, into a waveform vectorscope, the blacks are -7.5 and the whites are at 105. The chroma is just a tiny bit high.
Why is there such inconsistency between these three? How do you deal with it when you want to make a pro quality DVD?
And, most importantly, which program is making this change in levels: compressor, or DVD Studio Pro?
The target audience for my DVD is the consumer market, but it'll also be sent to industry people, so it needs to look as good as possible.
Thanks for your help.Exiting my exile as this thread is interesting.
A couple of things. If you work at a place with a big ole 8000 switcher, there should be some staff engineers to help you track down your black level problem, aren't there? Also, there's no need to hit a switcher crosspoint simply to monitor your levels in a waveform/vectorscope.
In FCP, black is digital which means zero IRE. The output of your dvd player is analog which means black is 7.5 IRE. Darn near every dvd player made has a menu choice to manipulate black levels, you should probably find out where your studio dvd player is set.
The dvd player output is analog, why not plug the thing into an analog waveform?
If you must convert the dvd output to SDI, you need to make sure the frame shaker TBC controls are set to unity, did you do this?
If you must hit a switcher crosspoint, (my knowledge of the Sony switchers is very very thin) there are handles within the switcher for TBC controls; make sure that crosspoint is set to unity as well.
Black levels are tricky, without being there it's hard to tell you exactly why. Have a house engineer walk through the steps with you.
But, to answer your first question, the built-in scopes within FCP are innaccurate, trust calibrated hardware scopes first. Again, if you must use a frame shaker, you MUST set the TBC controls to unity before you can make any sort of qualitative judgements.
Report back. -
When installing the new iTunes software, the message : "the older version of apple software update cannot be removed." What should I do? I tried deleting files related through control panel or the manual way, but it doesn't work. Am I missing something?
(1) Download the Windows Installer CleanUp utility installer file (msicuu2.exe) from the following Major Geeks page (use one of the links under the "DOWNLOAD LOCATIONS" thingy on the Major Geeks page):
http://majorgeeks.com/download.php?det=4459
(2) Doubleclick the msicuu2.exe file and follow the prompts to install the Windows Installer CleanUp utility. (If you're on a Windows Vista or Windows 7 system and you get a Code 800A0046 error message when doubleclicking the msicuu2.exe file, try instead right-clicking on the msicuu2.exe file and selecting "Run as administrator".)
(3) In your Start menu click All Programs and then click Windows Install Clean Up. The Windows Installer CleanUp utility window appears, listing software that is currently installed on your computer.
(4) In the list of programs that appears in CleanUp, select any Apple Software Update entries and click "Remove", as per the following screenshot:
(5) Quit out of CleanUp, restart the PC and try another iTunes install using an iTunesSetup.exe (or iTunes64Setup.exe) downloaded from the Apple Website:
http://www.apple.com/itunes/download/
Does it go through properly this time? -
ok, so I transferred my 3S info to my 4S by restoring from an old phone backup. But SIRI is gone and god knows what else?? Can I get my old stuff into the new phone and keep the 4S new functionality?
I suspect unless he had some items in iCloud backup then they are gone. Connecting an iPhone to a different library from that to which it was previously connected will result in the device asking if you want to erase it.
-
I get a message "The file "iTunes Library.itl" cannot be read because it was created by a newer version of iTunes." Please advise what I need to do to get around this issue - at the moment iTunes wont open up!
Hi did you ever get a solution to this problem? Having the same issue myself!
-
i recently bought a few films from itunes but i had to reset my laptop and the films have gone and i have tried downloading purchased items but no films come up and im not buying them again. what do i do now to get my films back ?
Did you fail to back up your purchases?
If so, then they are gone. -
my phone just has searching... up in the top left hand corner and it has been like this for 4 hours now! i am unable to make calls or texts. what should i do? It is an iphone 5 by the way
Take a look at this link, http://support.apple.com/kb/TS4148
-
All of my songs have exclamation points next to them but when I go to my iTunes media folder to find the files, there is nothing in the folders. Any idea what happened and how I can get my music back?
I wish I could help. There are numerous threads about missing music but last I looked, no solution. You might want to read through them anyway.
-
I'm having trouble using the iTunes and Apps store because i can't register my Nigerian mastercard. What should i do. i'm trying to register it in the Nigerian iTunes store.
Is this a new Apple iD? If it is, and you have already set it up, then you have two options:
1. Temporarily put a Credit Card or Gift Card on the account to download the free app. If you put a credit card, then once you have downloaded the app, you should be able to go into your Account preferences and change the payment option to = None.
2. You can download the fee App, and then set up a new Apple ID.
Cheers,
GB -
I have a macbook pro 17" 1,1 model (early 2006), but I do not have installation discs.
If I order a replacement, what version is it?
Can I install the latest version 10.8.4 in 1,1 model?
If it is possible, what I have to do to get it done? And the price?
ThanksMacBookPro1,1 can only run Mac OS X 10.6.8, as it has got a 32-bit processor.
If you order replacement DVDs, Apple will send you DVDs with the original Mac OS X version that came with your Mac, in this case, Mac OS X 10.4.5.
If you decide to get replacement DVDs, Apple will only charge you for the delivery
Maybe you are looking for
-
How to stop the posting of documents when there is an error in record
Hi, I have one issue with respect to posting of documents. In my Exl sheet there are 1900 records which would split into 950 records during run time. For each 950 records a document to be created. Here the issue, during test run thers is no error wh
-
I have a form for booking appointments and would like the date field to automatically fill with today's date and to print. I have set the text field's format to "Date" and when I place the cursor into the date field, today's date shows. It disappears
-
When to support autocad 2012 in acrobat x?
It was long time that Autodesk release autocad 2012 products, but it is still missing pdf converting toolbox in ACad 2012. So is there any update or time talbe about this? Thank you all~ Regards from Asia
-
How to put iphone in DFU mode ?
Hello, how i can put my iphone4 in DFU mode ?
-
Hi all, I'm following the "2 day HTML db developer" guide and I've come across a problem. Following all the steps of the "issue tracking app" I have created a form for insert/updating/deleting issues. Here the form contains a hidden item for navigati