What video formats will work on the latest ios version using the camera kit

question as per heading

Pad2, the new iPad Supported Video Formats & Movie Formats
H.264 video up to 1080p, 30 frames per second, High Profile level 4.1 with AAC-LC audio up to 160 Kbps, 48kHz, stereo audio in .m4v, .mp4, and .mov file formats;
MPEG-4 video up to 2.5 Mbps, 640 by 480 pixels, 30 frames per second, Simple Profile with AAC-LC audio up to 160 Kbps per channel, 48kHz, stereo audio in .m4v, .mp4, and .mov file formats;
Motion JPEG (M-JPEG) up to 35 Mbps, 1280 by 720 pixels, 30 frames per second, audio in ulaw, PCM stereo audio in .avi file format
 Cheers, Tom

Similar Messages

Any Skype Video that will work with the A1 ?

Is there a version of Skype Video that will work with the A1 ?
Moderator Note: Edited subject to match content.

Skype works wonderfully on the HTC Thunderbolt. The Tegra single core is just fine. It's not the chip, it's this device. As I've written as well, playback of any video is poor and any HD video is unwatchable. The phone plays HD video reasonably smoothly.
The Skype issue is the same - the app sees that it is video capable but cannot find the front facing camera (or any camera for that matter.) I'm surprised to find that video functions on this device don't work very well. Hopefully the company will be behind supporting this device. I'm surprised that it has Gingerbread only but you can't expect them to dump these out without having made sure they worked properly just for simple things that have worked properly on comparable devices.

What SSD drives will work in the GT60 0NE?

I'm about ready to give up on my GT60. I have purchased two different SSD drives and neither one is recognized in the bios when placed in the first drive slot. They are recognized in the 2nd drive slot, but not the first. I've updated everything, bios and firmware. Will someone tell me what model and brand SSD drive will work int the GT60? When the operating system is install in the second drive slot, i can't use the first drive slot for data because it won't boot windows. So, i have to leave the first drive bay empty. Tech support could not help me.

Quote from: maximus216 on 10-February-13, 21:51:49
I'm about ready to give up on my GT60. I have purchased two different SSD drives and neither one is recognized in the bios when placed in the first drive slot. They are recognized in the 2nd drive slot, but not the first. I've updated everything, bios and firmware. Will someone tell me what model and brand SSD drive will work int the GT60? When the operating system is install in the second drive slot, i can't use the first drive slot for data because it won't boot windows. So, i have to leave the first drive bay empty. Tech support could not help me.
It's rather difficult to recommend a drive....
What drives did you already try?
Are you trying to use the SuperRaid drives?
Do you need a normal 2.5" drive or mSATA drives?
Honestly, any drive should work, it just may not work perfectly. For instance, Samsung 840 Pro drives are known to only operate at SATA II speeds, even when installed in the SATA III slot.
Any Sandforce 2281 based drive should work fine. Intel 520 series should work well, along with 530 as well.

What camera models work with the camera Kit.

This Camera was not listed as one that works. But I gave it a try anyways and I was able to import pictures just fine from it..
I have the Ipad WIFI + 3G.
Plugged the Camera's USB cable into the camera kit ipad adapter and the Ipad Photo app popped up and let me select the pictures I wanted to inport.
The Camera is a 3 year old Olympus Stylus 720SW Shock and waterproof Digital Camera.

It's a proprietary accessory. The build of iOS is not supported for that device whereas it is supported in the iPad. Similar to why there are certain apps that only work with iPad.

What video format will iTunes accept?

I want to add some videos to my music video library. What format will iTunes accept and play? I am not concerned about playing them on an iPod so I would like a little better resolution than the standard for the iPod. Help!!!

Perhaps this will provide the information you need:
Adding, Browsing, and watching videos in iTunes
Hope it helps.

Which video formats will work for sure in FrameMaker 11?

I have done multiple test with somewhat discouraging results now. I want to embed a small video file in a FrameMaker 11 file and have it work in pdf. But even though this features should be able to work in both FrameMaker 10 and 11, my results are poor to say the least. I have tried multiple videoformats and sometime I am in luck and the video embeds and works, but most often it does not embed or it opens somewhere else on the page than the place where it was inserted. Is there a best practice for embedding video regarding file formats, distiller settings etc. I have spent several days now trying to make this work the way it is expcted to.
regards
Bjørn

I am looking at a new project where I will have to do exactly this, so I am also interested in an answer to studiosm's query.
Thanks,
Laurie

What wireless speakers will work with the "remote speaker" feature?

I want to use the remote app on my iphone to control my itunes library and was considering purchasing some speakers to put out by my pool. My question is what kind of speakers will itunes detect? what technology are we talking about? RF, Bluetooth?

iTunes itself, that is it's built-in remote speaker function, will work only with an Airport Express. There may be other wireless speakers that have their own drivers or transmitter; someone else here may be able to make a recommendation.
Message was edited by: Dave Sawyer

What video card will work in a mac pro 1.1 2006?

what video works in a mac pro 1.1 2006 ? (I have a ati 1900xt 512 mb now!)

Not to be difficult but you do realize this is being asked and discussed today in multiple threads, and for the last... 23 months too.
Apple sells ATI 5750 $249 and is fine.
http://www.barefeats.com/wst10g5.html
http://store.apple.com/us/product/MC742ZM/A

What remote controls will work with the iMac 27inch.

Okay I hung the new iMac on the wall in my kitchen. Used the apple adapter I have a little apple remote control that works the dvd player fine. Of course the wireless keyboard and the wireless mouse work fine. I have an elgato tuner because this iMac is my dvr/tv does anyone have a remote that will work the iMac as a dvd and work the elgato hybrid tuner. Just trying to make this simple. Thanks

iTunes itself, that is it's built-in remote speaker function, will work only with an Airport Express. There may be other wireless speakers that have their own drivers or transmitter; someone else here may be able to make a recommendation.
Message was edited by: Dave Sawyer

Does anyone know if MOV or MP4 files from the JVC GY-HM150U will work with the Camera Connection Kit and then be readable by iMovie or similar apps?

The JVC GY-HM150U camera and others in it's line say they offer recording in two different formats:
Native .MOV format
Fastest HD shoot to edit workflow. Edit immediately on Final Cut Pro™ or Premiere™ without conversion or transcoding
Native .MP4(XDCAM-EX™) format
Native File Recording
Because it uses QuickTime™ as its native file format, the GY-HM150U is the perfect choice for users of Apple's Final Cut Pro™ editing system. Both HD and SD MOV files recorded by the camcorder can be dropped directly into Final Cut Pro™, keeping them first-generation and eliminating the time-consuming process of file conversion.For users of all major NLE systems, including solutions from Adobe, Avid, Grass Valley, Vegas and Apple, the GY-HM150U supports the MP4 file format, which can be brought into your editing system without re-encoding.
HD VIDEO RECORDING
Recording media
SDHC (Class 6/10), SDXC Slots: x 2
Video recording
Video codec: MPEG2 Long GOP
QuickTime™ File Format for Final Cut Pro™ (HD/SD)/
MP4 File Format (HD)/AVI type-2 File Format (SD)
Recording mode
HQ mode: VBR, 35 Mbps (Max) MPEG-2 MP@HL
SP mode: CBR, 25 Mbps (1440 x 1080i)/
19 Mbps (1280 x 720p24/25/30): MPEG-2 MP@H-14
19 Mbps (1280 x 720p50/60): MPEG-2 MP@HL
SD Video: DV compression 4:1:1, 8-bit, 25Mbps
Audio: LPCM 2ch, 48 kHz/16bit
Video frame rate
NTSC settings:
HQ mode: 1920 x 1080/59.94i, 29.97p, 23.98p, 1440 x 1080/59.94i,
1280 x 720/59.94p, 29.97p, 23.98p
SP mode: 1440 x 1080/59.94i, 1280 x 720/59.94p, 29.97p, 23.98p
SD mode: 720 x 480/59.94i
PAL settings:
HQ mode: 1920 x 1080/50i, 25p, 1440 x 1080/50i, 1280 x 720/50p, 25p
SP mode: 1440 x 1080/50i, 1280 x 720/50p, 25p
Audio recording
LPCM 2ch, 48kHz/16-bit(Internal stereo mic/External mic input)
and the files recorded to folders labeled "CQAV" (.MOV) or "BPAV" (.MP4), respectively, located in /PRIVATE/JVC/ off the root.
So will the Camera Connection Kit see them properly and transfer them over to Photos, and then will iMovie be able to handle them? Or is the CCK restricted to only formats derived from DSLR cameras with "DCIM" folders, as I have heard?
Any knowledge, especially first hand testing, would be greatly appreciated!
Thanks,
David
Message was edited by: dwoodworth
Changes made to correct the recorded file paths.

Excuse the late post but just wondering if you came up with a solution for this problem? I experienced the exact same issue but copying the movies from Aperture into iTunes (which worked) still didn't allow them to be played on the iPad. As they had played faultlessly when imported directly from the camera connection kit!

What Video Formats will iDVD5 import?

Apple's website is not very clear on this.
Will it import anything other than DV?
Will it import all QT codecs? MPEG2?
Thanks for any help,
Ross
P.S. My search here did not find it either.

I'm late to this thread - so maybe this is for Those Who Come After.. - but, I found this all a bit hard to follow & still can't figure out why Sheila's buying Toast (a great but not cheap product) to make DVDs with all the 'fancy bits' when she already has a superb, free product that does precisely that.... iDVD. (Compared to most of the other software I've used to do this stuff iDVD is so User-Friendly I've taken it home to meet Mother ..
In a general answer to the original question - and related -, (HDVid,pics/extras aside)
b all the iDVD/ iMovie products were designed to take Digital Video,, i.e. DV from a compatible DV Cam (or precisely-formatted DV files which came from DV from a compatible DV Cam...) work with it and produce various output or Delivery products (whatever else the Docs etc. may suggest).
Ignoring pictures, iDVD takes in DV, allows extensive easy user customisation and produces DVDs after 'hidden' transcoding To MPEG-2 and creating the full DVD structure itself. (you could start from lots of other formats, transcode to a DV file and use iDVD from there but the results will likely range from bad to unviewable - if your Dad sends you an MPEG2 file, that's what you'll have to do to use iDVD - and chances of the transcoding screwing up are high - in my experience of the huge variations in file format/quality/bug level etc on PC-encoded MPEGs).
Best approach for iMov/iDVD (or almost anything else...is as suggested by our friend above):- have him send you a DV Tape copy, access a cam for a couple of hours and use iMovie to Capture as a DV file and proceed from there .... as you encounter the inevitable roadbumps (buy some DVD-RW.. you'll always have the original, full, highest-quality DV to go back to.
Toast (and DVDSP & other DVD creator/author tools) require solid, standards-compliant MPEG-2 as input (but I refer you to my comments above). There are a number of tools that'll do the DV->MPEG2 transcode on the Mac. They vary in quality, speed, price...... (you can't easily use the 'hidden' iDVD stuff last time I looked...).
To put it less technically, e.g. Mpeg-1 is mostly pretty small and pretty poor quality. "Enlarging' it in transcoding to DV is just going to give you a LARGE, bad-quality picture... - [an extreme example, but transcoding UP or 'across' - in 'quality' - is always bad. Transcoding DOWN from hi-quality DV to MPEG-2 for Delivery on DVD (e.g.) can be quite good - which is why you always try to do it ONCE and do it last.
[Perhaps it's not obvious to people, but most of these formats 'throw away' huge amounts of data/picture information: 2hr DV is about 30Gig... Transcoded to MPEG2, it may be 4. That's 26Gig worth of picture info that just isn't there anymore....]
For anyone working with this stuff, I recommend some Googling for info/tutes and FAAQs on Capture, editing and Delivery CODECs (CODECCentral used to be one....)
b 1 line summary: wherever possible, start with hi quality DV (or better), edit/play about in that, last, transcode to Deliver in whatever suits.
Best wishes.....

What bluetooth speaker will work with the new IMAC 27"?

Is Bose better than JamBox? Can someone recommend one? Is the speaker built into the new IMAC 27" good enough without external speaker?

I would expect the Yosemite list to be about the same as what is well-supported today.
This guy (Mac Gizmo guy) has done some research and lists on his site cameras that work with Macs AND are available on amazon.com.
I believe his recommendations are accurate, BUT -- Full Disclosure: gets some payments from amazon for his service.

What video formats are compatible in DVDSP??

I have DVD Studio Pro 4 and I need to know what video formats are compatible in the program? I made an .m2v file but its too large to fit even on a DL DVD so I need to drop the .m2v file into Mpegstreamclip and convert it to something else and decrease the size so then I can drop it back into DVDSP and burn it. Any help with this? What are formats supported in DVDSP? Or, is there another way around my problem (too big of a file)?? Thanks!

Can you make the audio AC3? That may put you under.
Also keep in mind that if the 2 hour 2 minute movie is that large in file size, it means it probably was encoded at a high rate which can cause issues (you can try to re-encode the m2v in a couple of ways if needed)
As to the story issues it sounds like you made a story accidently. Take a look here
http://dvdstepbystep.com/layofland.php
In the blue section towards the upper left, you will see the story listed in the track icon - delete the story and you should be good to go

What external modem will work with Satellite L500-1XL running Windows 7

Hi,
When in Spain I need to use dial up to the internet via Telefonica.
I am assuming the L500-1XL does not have an internal modem?
What external modem will work with the L500-1XL running Windows 7 ?
Many thanks in advance for your help.
A

Hi
Youre right Satellite L500 doesnt have an internal modem so you need an external one.
I think you can buy every modem that is at least compatible with Vista. Alternative ask your authorized service provider or favorite computer dealer
Friend of me has good experience with 56K modem from USRobotics like this one:
[USRobotics 56K USB Faxmodem USR5637|http://www.amazon.co.uk/USRobotics-56K-USB-Faxmodem-USR5637/dp/B0019LZCEI/ref=sr_1_1?ie=UTF8&s=electronics&qid=1269253039&sr =8-1]

What earlier version of FCP will work with the intel-3processor?

what earlier version of FCP will work with the intel-3 processor?

The version of the CR designer that the reports were created in is really not that important. Though more on that below. What you need is Crystal Reports XI R2A (11.5.x). That is the last version of CR to ship the Report Designer Component (RDC) that you are presumably using at this time. Note that this version is out of support thus no fixes, no phone support, though we welcome your queries on these forums. To obtain CR XI R2A you will have to contact sales; 866-681-3435. Do not get CR 2008 (12.x) as this version does not ship the RDC and only has the SDK for .NET and Java.
Re. version of the reports. While the version of the designer the reports were created in should not be that important, the older the designer, the more potential problems you may run into. Updating the reports to CR XI R2A is highly advised. You can do this manually by simply opening the reports in the designer and saving them - making sure they still run once that is done. Alternatively, you can do this in code by simply using the .SaveAs method, or exporting to rpt file format. This may not however update the database connectivity correctly (the database engine was completely rewritten in CR 9) and testing will be needed to make sure these reports still work. This is particularly true of your version 8 reports. Version 9 reports and later should be OK.
Ludek
Follow us on Twitter http://twitter.com/SAPCRNetSup
Got Enhancement ideas? Try the [SAP Idea Place|https://ideas.sap.com/community/products_and_solutions/crystalreports]

What video formats will work on the latest ios version using the camera kit

Similar Messages

Maybe you are looking for