What would cause the EVA WWN to change

Good Morning,
After a scheduled power outage my EVA P6000 Management Module changed its World Wide Name automatically causing our licenses to not load. Does anyone know of any possible causes?

Can you be more specific?
When you power it on, you should get a red Pilot light when it's ready to fire. If you press the light (it's a button) it should test-fire the flash. That will confirm the flash actually works.
You can tell the camera to disable the flash... this is useful when you just want to use the flash's focus-assist beam to help the camera lock focus, but do not actually want the flash to fire. Check your camera menu... probably under "External Speedlite Control" -> "Flash Firing" and check that it is set to "Enable".
Tim Campbell
5D II, 5D III, 60Da

Similar Messages

What would cause the microphone in the iPhone 3Gs to stop working?

What would cause the microphone in the iphone 3Gs to stop working?

Basic troubleshooting steps are restart, reset, restore. If these are tried and you still have problems then you have a hardware failure and will need to have your phone replaced by Apple.

What would cause the original I Pad shut itself off while playing games or online? it is not a battery issue or time issue. When I turn it back on it goes to were I was when I was online ,but have to start games over.

What would cause the original I Pad shut itself off while playing games or online? it is not a battery issue or time issue. When I turn it back on it goes to were I was when I was online ,but have to start games over.

The original iPad has a slow processor and only 256 MB of memory so it often runs into low-memory failures.
Double click the home button and dismiss all of the recents - I do that weekly.
Then reboot by holding both the power and home buttons until the apple logo appears, ignore the red slider - I also do that weekly.
Both seem to help to reduce the low-memory faults that occur.

What would cause the printer to only print text in microsoft word but no images

i have a hp deskjet D1320 printer, windows xp operating system, and i have always printed greeting cards from microsoft word by inserting an image and then printing it with the printer set to duplex(2sided)printing option, so after you print the image you flip the card around and then print the text on the inside of the card. now the printer does not print any images when i insert the image and then click print it just runs 1 piece of paper through the printer and stops but it will still print text just fine, does anyone know what would cause this type of an issue?
thank-you,
hwnugent

Hi there hwnugent,
Try downloading and running the print and scan doctor located here:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03275041&cc=us&dlc=en&lc=en
It can fix a lot on its own and if not give a better idea of what is going on. Let us know the results.
Best of Luck!
You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

What would cause the flash not to fire?

What would cause 580ex not to fire?

Can you be more specific?
When you power it on, you should get a red Pilot light when it's ready to fire. If you press the light (it's a button) it should test-fire the flash. That will confirm the flash actually works.
You can tell the camera to disable the flash... this is useful when you just want to use the flash's focus-assist beam to help the camera lock focus, but do not actually want the flash to fire. Check your camera menu... probably under "External Speedlite Control" -> "Flash Firing" and check that it is set to "Enable".
Tim Campbell
5D II, 5D III, 60Da

I have a macbook pro 10.6.8 system. My hard drive was replaced under warranty. Since then, my computer runs hot. The original hard drive never ran hot. What would cause the new hard drive to run hot?

I have a 2011 MacBook Pro, OS X 10.6.8, 2.2 GHz Intel Core i7, 4 GB 1333 MHz DDR3. This is my first computer so don't know anything about trouble shooting. A week before the warranty expired, I took my computer to Apple to be checked. I was told that my hard drive was bad and they replaced the hard drive. Since then, my computer runs hot most of the time and the fan is constantly coming on, which is good My computer rarely ran hot with the original hard drive. What would be causing this?

racergirl,
have you tried resetting your MacBook Pro’s System Management Controller, to see if that makes a difference with the heat?

What would cause the display to be blurry and fuzzy

What causes the display to be blurry and fuzzy

Have you dropped the iPad?
Try this - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.) No data/files will be erased. http://support.apple.com/kb/ht1430
 Cheers, Tom
BTW - You don't need to double post.

What would cause the computer to have a continuous knocking sound below the key board on the right hand side?

I have had my MacBook Pro since the middle of 2009 and am concerned that this continuous knocking sound that is inside and on the right side of my computer is indicative that my computer is starting to die on me. Has anyone experienced this same issue? And if you have what was the determined cause.
Thanks you

raymar65 wrote:
Hello Barney, its microsoft office 2008 , not sure how to revert to original shipping thanks Ray
There should be disks that came with the Mac. Gray in color, likely two of them. One is the installer.
As I mentioned, I'm not sure if just booting into the installer and erasing the drive with Disk Utility is simple with the recovery hd. However, there are other posts around here I've seen discuss reverting to Snow Leopard, so I'm sure you can find something that describes it.
If you've lost the disks, you should call AppleCare and order replacements for the new owner. They'll need the serial number which you can find from About This Mac (click on the version number twice).
As for Microsoft 2008, I would suggest that the new owner install that before installing Mountain Lion.

What would be the best way to change the color of part of this image? (image attached)

I am on XP using PS CS4.
Please see the photograph below. I would like to change the color of the shirt/apron of this lady & I was wondering what the best way is to do that. I know if I try replace color, the white bowls change color as well. In the past I have isolated parts of images using paths, but I wanted to know if that was the most efficient way. Maybe masking is the answer. I just wanted to hear from the pros
Thank you.

You're welcome!
Refine Edge button is in the options bar when the QST is active.
Refine Mask should be available whenever a mask is targeted.

What would cause a enum typedef constant changes during execution

Hello,
In my program I having a problem with an enum constant for a tab selection changing value at runtime. The enum is in the initialization part of the program and when I single step through the loop you see the tab property node for the value highlight and then in the next step the enum changes value. I'm running LV 8.0
Any information will be greatly appreciated.
Gary
Solved!
Go to Solution.

Ben,
Here are three jpg's to view with the first one once I enter the loop, the second is single stepping up to the property node and the third is the next single step and where the constant changes. I hope this helps I'm looking into a possible race condition could be the cause of this, but I'm not sure yet.
Gary
Attachments:
Enum constant changing at run-time.JPG ‏177 KB

What would cause the Messages App to only work intermittently?

The first letter typed should switch the Send button on indicating things are ok, more often than not this doesn't happen. Settings seem to be right so what else might be causing this?

I'll bet the lightbulb for execution highlighting isn't visable either is it? The problem is that someone turned off debugging for the VI in question. Debugging code does cost a little time so people who typically run their applications in the development system will sometimes turn off debugging. (Building a standalone application forces debugging off automatically).
To be able to probe your routine, right click on the vi's icon in the title bar and select "VI Properties..." and go to the "Execution" catagory and make sure the box labled "Allow Debugging" is checked.
This should put things right...
Mike...
Certified Professional Instructor
Certified LabVIEW Architect
LabVIEW Champion
"... after all, He's not a tame lion..."
Be thinking ahead and mark your dance card for NI Week 2015 now: TS 6139 - Object Oriented First Steps

What would cause the speaker in my iPad (III) to stop working suddenly?

I was listening to a podcast yesterday when the sound got staticky and the speaker stopped working. I tried plugging in external speakers and those do work, but that is the headphone jack . If I try to play a game with sound, it comes on very low - no matter how high up I have the sound- and then fades after about 30 seconds. The iPad not quite four months old and is in an OtterBox case, and has been since day one. Any ideas on what could have happened and if this may be something covered by the warranty? Thanks!

Mommylinda wrote:
I...I am in Japan and doubt they speak much English in the Tokyo store!
You'll be pleasantly surprised,

What would cause the screen to swith between backgrounds as if it is being controlled remotely? the system had created 7 new folders on it's own.

System is currently switching between mutliple screens without me touching it. The system has created several new folders. The system is performing as if it is being remotely controlled.

How recently did you switch? If it's less than 60 days, then Verizon simply reinstates your previous account. The fact that you were on the EDGE plan and mailed the devices back, and they apparently are somewhere in the system, could cause complications, and it might just work out that you just go back on the same plan and they set you up with the same devices. I'm not sure how it will go - but since you are still being billed for the devices...

Monitor display issues: what would cause the monitor to show really off colors?

When booted from my DVD startup disk the colors are fine. When using the computers startup, the colors are like a 35mm film negative. Any ideas out there?

troydimock
This solved my question:
Images on Monitor are all "negative" (colors are reversed) since cat wa
Nov 13, 2006 6:29 PM (in response to BGreg)
control-option+command8

What would cause the response time of Firefox to be very long?

I have been using Firefox for years with few problems. Now Firefox takes seconds to respond to any request. If I use a mouse click before Firefox is read, "not responding" appears on the top line and the little blue revolving circle appears. Firefox finally responds after seconds. Explorer is responding normally, so I don't think it is my Internet connection. I am using Firefox 3.6.10 under Windows 7.

Check the Time Zone support option in Settings > Mail > Calendars > Time Zone Support.

What would cause the EVA WWN to change

Similar Messages

Maybe you are looking for