Whats the fastest way to get CS6 out of trial mode?

Premiere 6 is in trial mode, only allowing Standar Def DV settings. Application manager wont launch and says " Adobe Genuine Software Validation Failure. The product you are trying to install is not Adobe Genuine Software and appears to be counterfeit/ What is the most efficient way to get back to work?
Windows 7 64 bit

Please try the following document:
http://helpx.adobe.com/x-productkb/global/digital-certificate-revoked-aam.html

Similar Messages

What is the fastest way of getting data?

With a scanning electron microscope, I need to scan a 512*512 pixel area with a pixel repetition of 15000 (two channels), meaning averaging over 15000 measurements. Simultaneously I have to adjust the voltage output for every pixel.
I am using a 6111E Multifunction I/O board in a 800MHz P3. The whole task has do be done as fast as possible (not more than 20 minutes altogether).
What is the fastest way to get this huge amount of data with averaging and output in between? (E.g. do I use buffered read with hardware triggering or is there a faster way?)

Using the NI-DAQ API (not LabView) will give you a significant amount of more control over what happens and when to the data stream; which translates to a more efficient program. But you need to program in C/C++ or Delphi then. The Measurement Studio provides ActiveX controls that are like the LabView ones for C&C++ (they�re slow like the LabView ones though � not a lot you can do about the Windows GDI).
What are you trying to sample 15000 times? The 512*512 pixel field?
That�s almost 15Gigs of data! And it means you need to process data at 12.8MB/s to finish it in 20 minutes. I hope you know C, x86 assembly and MMX.
I would setup a huge circular buffer (NI-DAQ calls them �double buffers�), about 30 seconds worth or so, to use with SCAN_Start. Then I would proces
s the actual buffer the card is DMA�ing the data into with a high priority thread. Progressively sum the scan values from the 16bit buffer (the samples are only 12 bit, but the buffer should still be 16bits wide) into a secondary buffer of DWORDs the size of the screen (512*512), and you�ll need two of those, one for each channel. Once the 15000 scans are complete, convert each entry into a float divide by 15000.0f, and store it in a third buffer of floats.
If you wish to contract this out, send me an email at [email protected]

When I'm done with my fcp sequence, whats the best way to get it to dvd?

When I'm done with my fcp sequence, whats the best way to get it to dvd?

The advice to go to Compressor left out the part that you may want to convert your audio to AC3 becaus ethe MPEG2 bitrate is probably too high for DVD specs.
This method is in the DVDSP manual and it's in the Compressor manual, both difficult to locate, but easily searchable.
Here's what I'd do: Export the timeline form FCP in the native sequence settings, self-contained. Bring that self-contained movie into DVDSP and let DVDSP handle the transcode.
The advice to go to iDVD is even easier.
bogiesan

Whats the best way to get a big text file in a CLOB variable?

Hi,
I have a very premitive type of question.
I have a big text file, say 30 MB, in a Unix directory (Solaris). I want to get the whole text of that file in a CLOB variable.
I saw the procedure dbms_lob.loadfromfile/loadclobfromfile. In both these cases, according to the documentation, the target where is collect the data will be a BLOB and not a CLOB. So, I have to convert that blob into a clob.
If I want to avoid all this conversion process, whats the best way to get a text from a file into a CLOB variable?
Please suggest.
Regards

In addition, LoadFromFile is overloaded to handle both BLOB and CLOB:
PROCEDURE LOADFROMFILE
Argument Name                  Type                    In/Out Default?
DEST_LOB                       BLOB                    IN/OUT
SRC_LOB                        BINARY FILE LOB         IN
AMOUNT                         NUMBER(38)              IN
DEST_OFFSET                    NUMBER(38)              IN     DEFAULT
SRC_OFFSET                     NUMBER(38)              IN     DEFAULT
<BR>
PROCEDURE LOADFROMFILE
Argument Name                  Type                    In/Out Default?
DEST_LOB                       CLOB                    IN/OUT
SRC_LOB                        BINARY FILE LOB         IN
AMOUNT                         NUMBER(38)              IN
DEST_OFFSET                    NUMBER(38)              IN     DEFAULT
SRC_OFFSET                     NUMBER(38)              IN     DEFAULT

Whats the best way to get dvd onto 5800

Peoples,
I'm strugglin to get DVD onto my noka 5800. It's not obvious in the user manual and looking around the web i need to 'convert' it to the fim on.
Please does anybody have an easy, fool proof way of doing this??????
Message Edited by blueleaches on 21-Aug-2009 06:02 PM

If its possible there should be some walkthrough's on google.
http://www.lmgtfy.com/?q=whats+the+best+way+to+get+dvd+onto+5800

Im having trouble with my ipad mini in regards with the icloud back up notification; if i press "ok" it doesnt dis appear, i couldn open my ipad/turn off because of this notification; whats the best way to get rid of this? please help

im having trouble with my ipad mini in regards with the icloud back up notification; if i press "ok" it doesnt dis appear, i couldn open my ipad/turn off because of this notification; whats the best way to get rid of this? please help

Have you tried a soft-reset ? Press and hold both the sleep and home buttons for about 10 to 15 seconds (ignore the red slider if it appears), after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot.

Whats the best way to get the server name in a servlet deployed to a cluster?

          Hi,
          I have a servlet in a web application that is deployed to a cluster, just
          wondering what is the best way to get the name of the node that the server is
          running on at run time??
          Thanks


          Please try to modify the following code and test for your purpose: (check Weblogic
          class document for detail)
          import javax.naming.*;
          import weblogic.jndi.*;
          import weblogic.management.*;
          import weblogic.management.configuration.*;
          import weblogic.management.runtime.*;
          MBeanHome home = null;
               try{
                    //The Environment class represents the properties used to create
                         //an initial Context. DEfault constructor constructs an Environment
                         //with default properties, that is, with a WebLogic initial context.
                         //If unset, the properties for principal and credentials default to
                         //guest/guest, and the provider URL defaults to "t3://localhost:7001".
                         Environment env = new Environment();
                         //Sets the Context.PROVIDER_URL property value to the value of
                         //the argument url.
                         if(admin_url!=null){
                              env.setProviderUrl(admin_url);
                              //Sets the Context.SECURITY_PRINCIPAL property to the value of
                              //the argument principal.
                              env.setSecurityPrincipal(username);
                              //Sets the value of the Context.SECURITY_CREDENTIAL property to
                              //the value of the argument cedentials
                              env.setSecurityCredentials(password);
                              //Returns an initial context based on the properties in an Environment.
                              ctx = env.getInitialContext();
                         }else ctx = new InitialContext();
                         home = (MBeanHome) ctx.lookup(MBeanHome.ADMIN_JNDI_NAME);
                         ctx.close(); //free resource
                         // or if looking up a specific MBeanHome
                         //home = (MBeanHome) ctx.lookup(MBeanHome.JNDI_NAME + "." + serverName);
                         DomainMBean dmb = home.getActiveDomain(); //Get Active Domain
                         ServerMBean[] sbeans = dmb.getServers(); //Get all servers
                         if(sbeans!=null){
                              for(int s1=0; s1<sbeans.length; s1++){
                                   String privip = sbeans[s1].getListenAddress();
                              sbeans[s1].getName();
                         sbeans[s1].getListenPort();
                                             WebServerMBean wmb = sbeans[s1].getWebServer();
               }catch(Exception ex){
          "Gao Jun" <[email protected]> wrote:
          >Is there any sample code? Thanks
          >
          >Best Regards,
          >Jun Gao
          >
          >"Xiang Rao" <[email protected]> wrote in message
          >news:[email protected]...
          >>
          >> Sure. You can use the Weblogic management APIs to query ServerBean.
          >>
          >>
          >> "Me" <[email protected]> wrote:
          >> >
          >> >Thanks for your reply, i was hoping to find a better way for example
          >> >a class in
          >> >weblogic API.
          >> >
          >> >Thanks
          >> >
          >> >"Xiang Rao" <[email protected]> wrote:
          >> >>
          >> >>Physical: InetAddress.getLocalHost().getHostName()
          >> >>Weblogic: System.getProperty("weblogic.Name");
          >> >>
          >> >>
          >> >>"Me" <[email protected]> wrote:
          >> >>>
          >> >>>Hi,
          >> >>> I have a servlet in a web application that is deployed to a
          >cluster,
          >> >>>just
          >> >>>wondering what is the best way to get the name of the node that
          >the
          >> >>server
          >> >>>is
          >> >>>running on at run time??
          >> >>>
          >> >>>Thanks
          >> >>
          >> >
          >>
          >
          >

Using final cut studio what the best way of getting a mini disc in to FCP?

I do some weddings and record some audio on to a mini disc recorder ( the small ones . On my avid liquid edit suite I just used to run it in live or ingest it on a 2 hour timer, and just record audio.
What the best way to do it with final cut studio and final cut pro?

Is there a reason you can't do the same on your mac system? What outputs does the audio recorder have?
Jerry

IMovie: whats the fastest way to import and save all original media?

Good afternoon. Ok I need help please. Is there a way to simply take all the imported original media and just save it all in one fell swoop? Rather than having to import and then process/export clip by clip.
I thought I had a quicker way just grabbing all the original media from the imported camera (right clicking imovie library > show package contents > original media) untill I tried to play one of the original media files - no sound and it was mov file. I assume mp4 is better???
I have 2800 hours of video I need to import off my camera. I don't need to modify them at all, aside from the occasional combining of clips into one movie. So I need the fastest way. Importing and then exporting clip by clip will take me forever. I would prefer to just import and then just drag all 50 clips or so into my movies folder. But as stated above that does not seem to work as expected unless I'm missing a step.
Thank you!

ps Can I take the original media files (mov format) and batch convert them using handbrake or MPEG streamclip? And if so would the resulting videos then have sound? And which is the best format (container codec whatever) to export them to? Thanks!

What's the fastest way to get a broken phone replaced?

Summary:
What a joke. Clearly broken iPhone, but when I get to the store, no one will help me. I have to make an appointment with a "Genius" and come back later. In the meantime, no phone for me.
Anyone know the secret code to get timely help with a broken iPhone?
Details:
iPhone crashed yesterday around 5:00. Wouldn't go past Apple logo. Using the recovery mode, I have:
- Restored using my backup.
- Deleted my backup and restored to a "new phone".
- Re-downloaded and re-installed iTunes, deleted my backup, and restored to a new phone.
- Uninstalled iTunes, deleted all ipsw files, redownloaded and reinstalled iTunes and restored to a "new phone"
After each of these, the situation is the same. The phone works (albeit very slowly and unevenly) until I turn it off (off off, not standby). When I turn it back on, stuck at the apple logo again.
So now I sit at the apple store, hoping someone will miss their appointment and I can sneak in off the standby list. What a joke. I'm definitely going to have to swing by the at&t store and see about switching to a phone that has adequate support when it breaks. I love the iPhone interface, but with a complete meltdown in the first 6 weeks of ownership and the long wait to see someone to get it replaced, it's just not reliable enough as a phone (not to mention the fact that the 3G really isn't ready for primetime). Sigh.

Tamara wrote:
Make an appointment at the Genius Bar - http://www.apple.com/retail/geniusbar/ . You can also do it in store on any of the Macs there. It beats sitting around hopping a slot will open up.
I did both - I scheduled the earliest available appointment, but it was hours away and I needed my phone, so I tried waiting for a hour or so as well.
deggie wrote:
See my answer to your last post.
Are you some sort of VIP that I don't know about? Why should you get to just walk in and have your problem solved when others made a Genius Bar appointment and showed up for it.
I don't think I'm better than anyone else. I think anyone with a broken phone should be able to get immediate assistance. I wasn't looking for training in how to use my phone, or assistance with some obscure functionality - the freaking thing wouldn't turn all the way on and couldn't be used for it's primary purpose, that of a mobile phone.
Tenacious MC wrote:
I suppose you do the same thing when walking into a doctor's office without making an appointment and expect him to see you about your cholesterol being high? You'd go into an ER for an emergency like a broken arm but you're gonna have to wait in line just like everyone else unless it's a life-threatening condition.
See my response above. If my phone wasn't "feeling well", I could live with waiting to talk to someone. But my phone was in a persistent vegitative state and deserving of urgent care.
The one time I had a problem with my Motorola RAZR, I walked into an at&t store and the next available person helped me out (by replacing the nonfunctional phone). I didn't have to make an appointment with a special subset of the staff. I would expect Apple, the actual manufacturer (and, in my case, vendor) of the phone to at least meet the standard that at&t sets for phones they don't even manufacture.
And I hope for the sake for Apple's enterprise penetration plans that they don't share your misconception that this is just a matter of "hampering my lifestyle". It's a matter of interrupting mission critical infrastructure functionality.

Whats the best way to get an averaged measurements while scanning?

I currently have a PXI 4071 DMM and a PXI 2575 Mux. I've played around with the examples of how to do scanning of channels which all works out fine. However the scanning only takes one measurement every time it steps down the scan list. What I need is for every scan step to take X number of measurements and average them before moving on to the next scan step. I've played around with the Sample Count and Trigger count but cannot seem to get this done correctly. I've gotten it to the point where it runs through the scan list multiple times and I can average from that but I don't want to tax the relays that much. Can anyone point me in the correct direction for this?

Hey Duke,
I can say with great confidence that the 407x DMM is much more accurate
than any DAQ product NI sells; if you're seeing unexpected accuracy errors after acquiring one data point with the 407x DMM, I think the best method is to figure out the discrepancy, not average it out. I recommend you verify the DUT signal with a scope (you can use the DMM in digitizer
mode) to see if the signal is still settling as you take your first measurement. If this is the case, each successive measurement becomes much closer to the value you expect, so averaging 5 samples allows the system to settle at the later points, and we get close to the actual value. If this is the case, then I recommend you increase the settling time property (configuration»Advanced»Settle Time) enough that your DUT signal has settled and then take a single measurement (with increased aperture time, if desired, as mentioned previously). Note that the value you obtain will differ from the old system if the above conditions exist... the 407x measurements are more accurate.
Obviously, if you scope the signal and it's steady during your first measurement, then my previous post would solve the problem while still taking only one measurement. For my own curiosity, what type of measurement are you performing?
Keep us up to date on your progress and don't hesitate to post of with any additional questions.
-John Sullivan
Analog Engineer

Whats the best way to get a description for a code

Hi,
What is the best way to find description for a code, when both of them resides in different table.I have to do this like 3 times for different codes.The code and description lies in differnt table.
Can i use select statement.. if yes, what operator should i use?
Thanks

Hi,
to do a lookup you may either use the Key Lookup Operator (it makes it easier to define default return values if the lookup fails) or a Joiner (to probably outer join your lookup table).
If you have many lookups you can do them in one joiner instead of having a key lookup operator for every one of them to reduce the total number of operators in your mapping.
Regards,
Carsten.

Whats the best way to get a copy of a clients DB onto an internal test DB?

Hi there
We have a client who hosts an Oracle 9i DB in house and we need to get a copy of this DB onto our own servers for testing purposes. What is the best way to go about doing this?
I was reading about the data pump for exporting and importing [http://www.exforsys.com/tutorials/oracle-10g/oracle-10g-using-data-pump-export.html]
Would this meet my requirements and how easy is it to do? Also what type of export would I need to do (there a 5+ schemas using different tablespaces)
Sorry if this is all a bit vague, but i am not a DBA and have been tasked with doing this :(
Thanks in advance,
Toby
edit: sorry i meant a 9i DB
Edited by: redeye on Nov 5, 2009 11:21 AM

If you want to export schemas/objects from 9i db you wouldn't be able to use datapump for exporting them,although you can import the dump file that will be created using the datapump.
Determine what schemas you need at the test(destination) database, and then export them from the source(clients db) database.
Also make sure that on the target database server, os paths where the oracle related files will be created(redo logs,datafiles...) are the same as the ones that are on the source database.

Whats the easiest way to get data from R/3 from XI

Hi there
I would like to know if there is a way to to access a database table in the R/3 system in a user defined function in Message Mapping? I have to map some fields where I have to get data from a table. What would be the easiest way?
Thanks,
Jan

This article provides details on the usage of Generic Lookup API used for calling RFC from user defined functions.
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/a03e7b02-eea4-2910-089f-8214c6d1b439
RFC Lookup.
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/a03e7b02-eea4-2910-089f-8214c6d1b439

Whats the best way to get rid of a virus, whats the best way to get rid of a virus

Preferences

I'll echo MadMacs0's request for specific information about the threat. You should find it in Kaspersky's Detected Threats list. The first column will show the path of the file determined to be malware, and the Name column lists the name that Kaspersky calls that malware. We need to know what the full contents of both those values are. Be sure to resize the columns so you can see the whole thing, if necessary.
Most likely, this is just Windows malware attached to an e-mail message or something along those lines.

Whats the fastest way to get CS6 out of trial mode?

Similar Messages

Maybe you are looking for