Whats the power consumption in standby and read/write mode on the Hitachi HTS545032B9A302 ?

Hello, im about to but an ssd and dont want to pick a drive with more energy consumption to reduce the battery time so i wonder if someone knows the conumption for the Hitachi HTS545032B9A302 drive on the new macbook pro or in worst case if someone dares to approximately guess the consumption in W(Watt)

Does the hard drive label say 5V 700ma?
You might look at the Hitachi spec sheet for the A300/A301's, which have the same power specs: http://www.hitachigst.com/tech/techlib.nsf/techdocs/FFA370A7BF845F87862574FE0003 054C/$file/TS5K500B_DS_final.pdf

Similar Messages

HT201335 I found it cost a lot of energy . Is it true? Is there any spec to describe detail power consumption about airplay and airplay mirroring?

I found it cost a lot of energy . Is it true? Is there any spec to describe detail power consumption about airplay and airplay mirroring?

Welcome to the Apple Community.
The Apple TV uses 6 W, which IMO is hardly a lot of energy.

Optimising power consumption of backlight and wifi

Hi there,
Do you have any effective measures in place to optimise power consumption of backlight and wifi?
On my Thinkpad X200T they are by far the biggest consumers of power.
How much does backlight and wifi consume on your laptops?

@centos
Well, I tried acpi_osi='!Windows 2012' acpi_backlight=legacy and got 11.9 W and 4 hours which is a record
Interestingly when the results were 13.5 W and 15 W powertop showed
7.66 W 33.7% Device Display backlight
Now it shows
11.0 W 76.8% Device Display backlight
@orschiro
And I also have it twice
orschiro wrote:
If you go to the Device stats tab, you see that the % column is labelled Usage.
Out of curiousity, is Display Backlight displayed twice for you under Device Stats?
With acpi_osi='!Windows 2012' acpi_backlight=legacy and 11.9 W and 4 hours
5.52 W 76.8% Display backlight
5.52 W 20.0% Display backlight
Without acpi_osi='!Windows 2012' acpi_backlight=legacy and 13.5 W and approximately 3 hours
3.83 W 33.7% Display backlight
3.83 W 20.0% Display backlight

How to open a "manual" Physical standby database in read/write mode

Hi,
I am running Oracle Database 10g Release 10.2.0.3.0 - 64bit Production Standard Edition on Linux version 2.6.9-42.0.8.ELsmp ([email protected]) (gcc version 3.4.6 20060404 (Red Hat 3.4.6-3))
I've created a physical standby database, but since I am running Standard Edition, I am not using the DataGuard features. I use the rsync utility to copy over the archivelogs to the standby database, and I apply them periodically to the standby database.
The standby database is started this way :
startup nomount pfile='/u01/oradata/orcl/initorcl.stdby';
alter database mount standby database;
Everything runs perfectly fine, I can do "alter database open read only" and then I can do selects into tables to confirm that everything is up to date.
The thing is, if I shutdown immediate the database, then do just startup :
shutdown immediate;
startup;
The database opens with no error messages, but is still in read-only mode...
I read that the default behavior for a standby database is to open read-only, like I am experiencing, but I would like to know what is the right way to open it correctly in read-write mode (I understand that after that, my standby will not be standby anymore and that I will have to recreate my standby database).
Thanks,
Mat

Hello,
There're features which allows you to open a Standby database in Read/Write mode but for all I know
it needs Entreprise Edition.
In Enterprise Edition you can use Logical Standby database. More over, for Physical standby there's
a way by using flashback database so as to rolling backward the database and avoiding to recreate
the Standby.
In Standard Edition I'm afraid that you'll have to recreate your Standby database.
Best regards,
Jean-Valentin

Open standby database read/write

What's the syntax to open a standby database read/write?
Any help will be appreciated.
Thanks

Technically it's not open Standy database read/write,
Activate the standby database using the SQL ALTER DATABASE ACTIVATE STANDBY DATABASE statement.
This converts the standby database to a primary database, creates a new reset logs branch, and opens the database. See Section 8.5 to learn how the standby database reacts to the new reset logs branch.
Physical Standby can only be open read/write in 11g with active standby option.

Search record combine with read only and read/write record

can the search record display read only and read write only record together ?

Maybe your Mac-B user account has the same (short) user name
as your Mac-A user account. Matching user names or short user names
could make the Mac-B account able to Read & Write to your shared folder.
Because I think you can log in with short user names to a server
as well. I guess passwords should be matching as well,
and perhaps the user ID's (System Preferences -> Accounts
-> right-click on user) also?
Cheers,
Vincent Verheyen.

Clone Production Database and Convert into Read Write Mode

Hi,
Please help me for below question...
How to Create Test Database from Production Database without transporting backup of Production Database to Test Database and the Test Database should be in different directory structure and converting into read write mode?
Please find me a solution as early as possible...
Thanks & Regards
Akhil

if you don't need to move backup from prod to dev you need to create rman catalog and have access on it from dev server , after that you will be able to duplicate your prod to dev without moving backup and database will be in Read write by default .

To export query from Access to Excel in Read/Write mode in VBA

Below is the code which exports the query named 'LatestSNR' from Access to Excel;
Public Sub Expdata()
Dim rst As DAO.Recordset
Dim Apxl As Object
Dim xlWBk, xlWSh As Object
Dim PathEx As String
Dim fld As DAO.Field
PathEx = Forms("Export").Text14 'path comes from the directory given in form
Set Apxl = CreateObject("Excel.Application")
Set rst = CurrentDb.OpenRecordset("LatestSNR")
Set xlWBk = Apxl.Workbooks.Open(PathEx)
'xlWBk.ChangeFileAccess xlReadWrite
Set xlWBk = Workbook("PathEx")
Apxl.Visible = True
Set xlWSh = xlWBk.Worksheets("Metadatasheet")
xlWSh.Activate
xlWSh.Range("A2").Select
For Each fld In rst.Fields
Apxl.ActiveCell = fld.Name
Apxl.ActiveCell.Offset(0, 1).Select
Next
rst.MoveFirst
xlWSh.Range("A2").CopyFromRecordset rst
xlWSh.Range("1:1").Select
' selects all of the cells
Apxl.ActiveSheet.Cells.Select
' selects the first cell to unselect all cells
xlWSh.Range("A2").Select
rst.Close
Set rst = Nothing
' Quit excel
Apxl.Quit
End Sub
After the execution of code, the query is transferred to excel sheet and is viewed in 'Read only' mode. If I try to save it, a copy of the excel file is produced. Can the Excel be opened in Read/Write mode ? so as to save the workbook and also to transfer
the query to same workbook repeatedly.
If in case the change of mode is not possible, then is there any alternative method?

Try this version:
Public Sub Expdata()
Dim rst As DAO.Recordset
Dim Apxl As Object
Dim xlWBk As Object, xlWSh As Object
Dim PathEx As String
Dim i As Long
PathEx = Forms("Export").Text14 'path comes from the directory given in form
Set Apxl = CreateObject("Excel.Application")
Set xlWBk = Apxl.Workbooks.Open(PathEx)
Set xlWSh = xlWBk.Worksheets("Metadatasheet")
Set rst = CurrentDb.OpenRecordset("LatestSNR")
For i = 1 To rst.Fields.Count
xlWSh.Cells(1, i).Value = rst.Fields(i - 1).Name
Next i
rst.MoveFirst
xlWSh.Range("A2").CopyFromRecordset rst
xlWBk.Close SaveChanges:=True
Apxl.Quit
rst.Close
Set rst = Nothing
End Sub
or else
Public Sub Expdata()
Dim PathEx As String
PathEx = Forms("Export").Text14 'path comes from the directory given in form
DoCmd.TransferSpreadsheet TransferType:=acExport, _
SpreadsheetType:=acSpreadsheetTypeExcel12Xml, _
TableName:="LatestSNR", _
Filename:=PathEx, _
HasFieldNames:=True, _
Range:="Metadatasheet!"
End Sub
Regards, Hans Vogelaar (http://www.eileenslounge.com)

ORA-22292: Cannot open a LOB in read-write mode without a transaction

Hi ,
somebody can help me, what is that problem.
I run the script by using the Oracle SQL developer to update the clob column.
error message is :
ORA-22292: Cannot open a LOB in read-write mode without a transaction.
Regards,
Message was edited by:
user533045

Without posting the code its difficult for anyone to figure out whats wrong with this
error.Please paste the code.
Khurram

Mounting UDF formatted DVD+RW in read-write mode

Hi folks,
I'm having trouble getting Leopard to mount a freshly formatted UDF DVD+RW in read-write mode. It always seems to come up mounted read-only regardless of the options I give mount or mount_udf. I've tried default and 2.5 versions of UDF, specifying fix-packet when creating the volume, specifying -w on mount_udf, specifying -o w on mount, etc.
The disc seems to be created okay, and shows free space..Just can't figure out how to use it. Any thoughts/working recipes? Example transcript follows..
Thanks in advance,
- Zanthrox
scutter:~ doucej$ newfs_udf -v "Backup" /dev/disk1
write to block device: /dev/disk1 last written block address: 2295103
scutter:~ doucej$ mkdir /Volumes/Backup
scutter:~ doucej$ sudo mount_udf -w /dev/disk1 /Volumes/Backup
scutter:~ doucej$ df
Filesystem 512-blocks Used Available Capacity Mounted on
/dev/disk0s2 454819840 320448088 133859752 71% /
devfs 213 213 0 100% /dev
fdesc 2 2 0 100% /dev
map -hosts 0 0 0 100% /net
map auto_home 0 0 0 100% /home
/dev/disk0s3 32905496 32284360 621136 99% /Volumes/Untitled
/dev/disk1 9178360 572 9177788 1% /Volumes/Backup
Looks good so far -- the volume was created fine, is readable, mountable, and shows free space..
scutter:~ doucej$ mount
/dev/disk0s2 on / (hfs, local, journaled)
devfs on /dev (devfs, local)
fdesc on /dev (fdesc, union)
map -hosts on /net (autofs, automounted)
map auto_home on /home (autofs, automounted)
/dev/disk0s3 on /Volumes/Untitled (ntfs, local, read-only, noowners)
/dev/disk1 on /Volumes/Backup (udf, local, read-only)
scutter:~ doucej$
....but it still won't come up read-write, so I can't actually use it.

If LVM has dropped write permissions on a volume or group then its probably for a good reason. You might want to look at the root cause for the failure and check /var/log/messages for any information.
If you don't care about the data, you might be able to to bring back write access using
<pre>
lvchange --ignorelockingfailure -p w VolGroup00-LogVol14
</pre>
But like I said, there is probably a good reason why the volume is write protected in order to prevent further damage, or because of a underlying hardware issue.

Clone production db, & convert it to read write mode

Hi Guys.,
I'm having dba1 & dba2 server's , At dba1 there is my production database , Using this production database I want to create a new 'test' database
"WITHOUT taking the BACKUP of MY production database."
Note: I want to convert 'test' database to read write mode Too.
please help me out with neat steps ,, Thanks in advance:-)

If your database version is 11g R2 then you can use active database duplication as Hermant says.
http://taliphakanozturken.wordpress.com/2011/06/26/creating-standby-database-with-rman-active-database-duplication-in-11gr2/
Otherwise you need data pump export/import, transportable tablespace, etc to transfer your data.
Talip Hakan Ozturk
http://taliphakanozturken.wordpress.com/

Average power consumption comparision: i7 and t500

Hi,
What is the average power consumption (non-peak) of a t500 system,
doing web-surfing and light tasks ?
I have read that the i7 mobiles (non-lenovo) are at 52W avg, and 75W peak,
and this will help me decide whether to buy the t500 or wait for the lenovo
i7 based laptops
thanks!

P8400 / P8600 etc core2duo mobile (2,2-2,4ghz) take 25W. I think in office use my T400 uses about 15W, not sure. It depends on load. I find quad core laptop CPUs quite useless for the average user.I think the i7 mobiles have a 45W specification, which is quite higher than the modern dual cores. I prefer longer battery life to having four cores i will most likely never use in daily work. This changes, of course, if you use your laptop as Desktop replacement or primarily for CPU intensive tasks, such as video en/decoding.
Thinkpad T400 (Windows 7 Ultimate x64)

Power consumption for router and switch

I have a linksys EZSX88W switch which I checked power consumption of 70ma idle. It's supplied by the adapter which has an output of 1000ma. Not sure what the consumption when switch is being used. I also have an WRT54GS but haven't checked consumption yet, but it's powered by the same 1000ma adapter. In an effort to save energy-that -GREEN FEELING- I was thinking of using on power adapter to power bothe the router and switch. Has anyone tried this yet?? Also if I posted this in the wrong area I hope the moderator will move the post.
thanks

So you are thinking of Powering on both the Devices using a single Power Adapter? Well never tried to make both the devices use a single power adapter. As far as i think its not possible. But if you still wish, you can give a try and check if that works for you or not.

What tool is used to open and read UCS tech support files

Hello,
Due to internal Infosec policies, I need to open and read UCS tech supoort files that I generate prior to sending them to Cisco TAC. Can someone tell me what tool I can use to accomplish this task? Thanks.

Good to hear.
Are you intending to blank out all the proprietary info? IPs, Hostnames etc?
Suggest an advanced editor such as ultraEdit which can find and replace any private information.
Robert

Issue regarding open word file and read only mode using c# & MS-word interop

i am programmatically open a word file for search and highlight keyword. my routine is working fine. the problem is when i am opening the file programmatically then a dialog come and ask me to open file in read only mode. the dialog look like below one
actually i do not want to open the file in read only mode because people can open and like to change and save. so guide me what i can do to not to open the file in read only mode.
here is my full code. just have a look and tell me what is wrong in my code or tell me any trick as a result i can open the file not in read only mode. here is my code.
private void button1_Click(object sender, EventArgs e)
            object fileName = "";
            string filePath = "";
            string strSaveasPath = "";
            DialogResult result = openFileDialog1.ShowDialog();
            if (result == DialogResult.OK)
                fileName = openFileDialog1.FileName;
                //strSaveasPath = Path.GetDirectoryName(path.ToString());
            //fileName = "Z:\\C0000000003.doc";
            List<string> _list = new List<string>();
            _list.Add("tridip");
            _list.Add("arijit");
            //object fileName = "D:\\CVArchievePath\\C0000000001.doc";
            object textToFind = "test";
            object readOnly = false;
            Word.Application word = new Word.Application();
            Word.Document doc = new Word.Document();
            object missing = Type.Missing;
            try
                doc = word.Documents.Open(ref fileName, ref missing, ref readOnly,
                                          ref missing,
ref missing, ref missing,
                                          ref missing,
ref missing, ref missing,
                                          ref missing,
ref missing, ref missing,
                                          ref missing,
ref missing, ref missing,
                                          ref missing);
                doc.Activate();
                object matchPhrase = false;
                object matchCase = false;
                object matchPrefix = false;
                object matchSuffix = false;
                object matchWholeWord = false;
                object matchWildcards = false;
                object matchSoundsLike = false;
                object matchAllWordForms = false;
                object matchByte = false;
                object ignoreSpace = false;
                object ignorePunct = false;
                object highlightedColor = Word.WdColor.wdColorGreen;
                object textColor = Word.WdColor.wdColorLightOrange;
                object missingp = false;
                Word.Range range = doc.Range();
                foreach (string line in _list)
                    textToFind = line;
                    bool highlighted = range.Find.HitHighlight(ref textToFind,
ref missing,
ref missing,
ref missing,
ref missing,
ref missing,
ref missing,
ref missing,
ref missing,
ref missing,
ref missing,
ref missing,
ref missing,
ref missing,
ref missing,
ref missing,
ref missing,
ref missing,
ref missing,
ref missing);
                System.Diagnostics.Process.Start(fileName.ToString());
            catch (Exception ex)
                Console.WriteLine("Error : " + ex.Message);
                //Console.ReadKey(true);
            finally
                //doc.Close(missing, missing, missing);
                if(doc!=null)
                    System.Runtime.InteropServices.Marshal.ReleaseComObject(doc);
                if (word != null)
                    System.Runtime.InteropServices.Marshal.ReleaseComObject(word);
                word = null;
                doc = null;
                GC.Collect();
                GC.WaitForPendingFinalizers();

I know it's a very old issue and I reached to this page looking for a solution. Finally, I have found a fix to this problem.
The problem is that we create an instance of Word and do not close it correctly. This makes program believe that the file is already open and hence you're getting the respective message of file being locked by you.
Set the visibility of your application to true and then when you close it both file and instance should close and you will not get the problem again.

Whats the power consumption in standby and read/write mode on the Hitachi HTS545032B9A302 ?

Similar Messages

Maybe you are looking for